From: Claas Langbehn <claas@rootdir.de>
To: linux-kernel@vger.kernel.org
Cc: jf1@IMERGE.co.uk, B.Zolnierkiewicz@elka.pw.edu.pl,
James@superbug.demon.co.uk, Knut_Petersen@t-online.de
Subject: RE: VIA IDE performance under 2.6.0-test7/8? (and test9)
Date: Sun, 2 Nov 2003 11:48:18 +0100 [thread overview]
Message-ID: <20031102104818.GA1981@rootdir.de> (raw)
Hi,
If I cat /proc/ide/via it shows that my harddisc is only
using 88,8 MB/s, but it is an U100-disc. hdparm show that
its using udma5, is this all correct, or should /proc/ide/via
show 99,9 MB/s ?
----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.38
South Bridge: VIA vt8235
Revision: ISA 0x0 IDE 0x6
Highest DMA rate: UDMA133
BM-DMA base: 0xdc00
PCI clock: 33.3MHz
Master Read Cycle IRDY: 0ws
Master Write Cycle IRDY: 0ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: yes yes
Post Write Buffer: yes yes
Enabled: yes yes
Simplex only: no no
Cable Type: 80w 80w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: UDMA PIO UDMA PIO
Address Setup: 120ns 120ns 120ns 120ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 90ns 330ns 90ns 330ns
Data Recovery: 30ns 270ns 30ns 270ns
Cycle Time: 22ns 600ns 60ns 600ns
Transfer Rate: 88.8MB/s 3.3MB/s 33.3MB/s 3.3MB/s
# hdparm -i /dev/hda
/dev/hda:
Model=ST3120023A, FwRev=3.33, SerialNo=3KA1ERGQ
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=234441648
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:
* signifies the current active mode
Regards, claas
reply other threads:[~2003-11-02 10:48 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20031102104818.GA1981@rootdir.de \
--to=claas@rootdir.de \
--cc=B.Zolnierkiewicz@elka.pw.edu.pl \
--cc=James@superbug.demon.co.uk \
--cc=Knut_Petersen@t-online.de \
--cc=jf1@IMERGE.co.uk \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox