From: Ernst Herzberg <earny@net4u.de>
To: linux-kernel@vger.kernel.org
Subject: Kernel 2.6.3: tg3: can't set full duplex
Date: Tue, 24 Feb 2004 07:46:58 +0100 [thread overview]
Message-ID: <200402240746.58494.earny@net4u.de> (raw)
Moin.
tweaky ~ # dmesg | tail
Mounted devfs on /dev
Freeing unused kernel memory: 156k freed
Adding 2000084k swap on /dev/sda2. Priority:-1 extents:1
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
tg3: eth0: Link is up at 100 Mbps, half duplex.
tg3: eth0: Flow control is off for TX and off for RX.
tg3: eth1: Link is up at 1000 Mbps, full duplex.
tg3: eth1: Flow control is on for TX and on for RX.
tweaky ~ # ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Half
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
Link detected: yes
tweaky ~ # ethtool -s eth0 duplex full
tweaky ~ # ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Half
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
Link detected: yes
tweaky ~ # dmesg | tail
Mounted devfs on /dev
Freeing unused kernel memory: 156k freed
Adding 2000084k swap on /dev/sda2. Priority:-1 extents:1
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
tg3: eth0: Link is up at 100 Mbps, half duplex.
tg3: eth0: Flow control is off for TX and off for RX.
tg3: eth1: Link is up at 1000 Mbps, full duplex.
tg3: eth1: Flow control is on for TX and on for RX.
-----------------
Nothings happens. Was working with 2.4.21
-----------------
tweaky ~ # ethtool
ethtool version 1.7
[..]
tweaky ~ # lspci
00:00.0 Host bridge: ServerWorks CMIC-HE (rev 22)
00:00.1 Host bridge: ServerWorks CMIC-HE
00:00.2 Host bridge: ServerWorks CMIC-HE
00:00.3 Host bridge: ServerWorks CMIC-HE
00:03.0 SCSI storage controller: Adaptec AIC-7892P U160/m (rev 02)
00:04.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
00:0f.0 Host bridge: ServerWorks CSB5 South Bridge (rev 93)
00:0f.1 IDE interface: ServerWorks CSB5 IDE Controller (rev 93)
00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev 05)
00:0f.3 ISA bridge: ServerWorks GCLE Host Bridge
00:10.0 Host bridge: ServerWorks CIOB30 (rev 03)
00:10.2 Host bridge: ServerWorks CIOB30 (rev 03)
00:11.0 Host bridge: ServerWorks CIOB30 (rev 03)
00:11.2 Host bridge: ServerWorks CIOB30 (rev 03)
00:12.0 Host bridge: ServerWorks CIOB30 (rev 03)
00:12.2 Host bridge: ServerWorks CIOB30 (rev 03)
03:01.0 PCI bridge: Intel Corp. 21154 PCI-to-PCI Bridge
04:00.0 PCI bridge: Intel Corp. 21154 PCI-to-PCI Bridge
04:01.0 SCSI storage controller: QLogic Corp. ISP12160 Dual Channel Ultra3
SCSI Processor (rev 06)
05:00.0 RAID bus controller: American Megatrends Inc. MegaRAID (rev 20)
0a:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5700 Gigabit
Ethernet (rev 14)
0a:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5700 Gigabit
Ethernet (rev 14)
---------------------------------
Problem is: With this switch this card hangs sometimes if fullduplex is not
switched on. And the port on the Switch supports full duplex ;-)
~Earny
reply other threads:[~2004-02-24 6:47 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200402240746.58494.earny@net4u.de \
--to=earny@net4u.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox