* 2.6.3: VIA+ACPI+yenta->hang
@ 2004-03-10 11:42 Mark Hindley
0 siblings, 0 replies; 3+ messages in thread
From: Mark Hindley @ 2004-03-10 11:42 UTC (permalink / raw)
To: linux-kernel
Hi,
I am doing a new install of 2.6.3 on an Acer 1353XV.
If I have anything more than acpi=ht loading yenta_socket causes a hang
requiring hard reset.
Boot gets as far as: (copied from screen)
Mar 10 11:23:41 mercury kernel: Linux Kernel Card Services
Mar 10 11:23:41 mercury kernel: options: [pci] [cardbus] [pm]
Mar 10 11:23:41 mercury kernel: PCI: Found IRQ 5 for device 0000:00:07.0
Mar 10 11:23:41 mercury kernel: PCI: Sharing IRQ 5 with 0000:00:08.0
Mar 10 11:23:41 mercury kernel: PCI: Sharing IRQ 5 with 0000:00:10.1
Mar 10 11:23:41 mercury kernel: Yenta: CardBus bridge found at 0000:00:07.0 [1025:0033]
Mar 10 11:23:41 mercury kernel: Yenta: Enabling burst memory read transactions
Mar 10 11:23:41 mercury kernel: Yenta: Using CSCINT to route CSC interrupts to PCI
Mar 10 11:23:41 mercury kernel: Yenta: Routing CardBus interrupts to PCI
Mar 10 11:23:41 mercury /usr/sbin/gpm[789]: Detected EXPS/2 protocol mouse.
Mar 10 11:23:41 mercury kernel: Yenta: ISA IRQ mask 0x0488, PCI irq 5
Mar 10 11:23:41 mercury kernel: Socket status: 30000010
Even without pcmcia in, apci seems unreliable, particularly ac and fan
modules. I get random hangs synchronised with the fan starting which
suugests an acpi related event. With just button and battery seems stable
Logs always empty
lspci -vv
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 3205
Subsystem: VIA Technologies, Inc.: Unknown device 7205
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [80] AGP version 3.5
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x2
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device b168 (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d1000000-d1ffffff
Prefetchable memory behind bridge: f0000000-f3ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 10
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:08.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8026 (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d0004000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 USB Controller: VIA Technologies, Inc. UHCI USB (rev 80) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin A routed to IRQ 4
Region 4: I/O ports at 1c00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.1 USB Controller: VIA Technologies, Inc. UHCI USB (rev 80) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 1c20 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 80) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin C routed to IRQ 9
Region 4: I/O ports at 1c40 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:10.3 USB Controller: VIA Technologies, Inc.: Unknown device 3104 (rev 82) (prog-if 20)
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 10
Interrupt: pin D routed to IRQ 11
Region 0: Memory at d0004800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc.: Unknown device 3177
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 4
Region 4: I/O ports at 1c60 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio Controller (rev 50)
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 9
Region 0: I/O ports at 1000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.6 Communication controller: VIA Technologies, Inc. AC97 Modem Controller (rev 80)
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 9
Region 0: I/O ports at 1400 [size=256]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:12.0 Ethernet controller: VIA Technologies, Inc. Ethernet Controller (rev 74)
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 4
Region 0: I/O ports at 1800 [size=256]
Region 1: Memory at d0004c00 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: VIA Technologies, Inc.: Unknown device 7205 (rev 01) (prog-if 00 [VGA])
Subsystem: Acer Incorporated [ALI]: Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min)
Interrupt: pin A routed to IRQ 4
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at d1000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Thanks for any help. Let me know if you need any more info.
Mark
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: 2.6.3: VIA+ACPI+yenta->hang
[not found] <A6974D8E5F98D511BB910002A50A6647615F4B49@hdsmsx402.hd.intel.com>
@ 2004-03-11 6:48 ` Len Brown
2004-03-11 10:27 ` Mark Hindley
0 siblings, 1 reply; 3+ messages in thread
From: Len Brown @ 2004-03-11 6:48 UTC (permalink / raw)
To: Mark Hindley; +Cc: linux-kernel
On Wed, 2004-03-10 at 06:42, Mark Hindley wrote:
> Hi,
>
> I am doing a new install of 2.6.3 on an Acer 1353XV.
>
> If I have anything more than acpi=ht loading yenta_socket causes a
> hang
> requiring hard reset.
Mark,
Please test the patch here:
http://bugzilla.kernel.org/show_bug.cgi?id=1564
thanks,
-Len
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: 2.6.3: VIA+ACPI+yenta->hang
2004-03-11 6:48 ` 2.6.3: VIA+ACPI+yenta->hang Len Brown
@ 2004-03-11 10:27 ` Mark Hindley
0 siblings, 0 replies; 3+ messages in thread
From: Mark Hindley @ 2004-03-11 10:27 UTC (permalink / raw)
To: Len Brown; +Cc: linux-kernel
On Thu, Mar 11, 2004 at 01:48:13AM -0500, Len Brown wrote:
> Mark,
> Please test the patch here:
>
> http://bugzilla.kernel.org/show_bug.cgi?id=1564
>
Thanks. Unfortunately, still hangs at the same point. Any other
suggestions? Would ACPI_DEBUG be helpful?
Mark
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2004-03-11 10:27 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <A6974D8E5F98D511BB910002A50A6647615F4B49@hdsmsx402.hd.intel.com>
2004-03-11 6:48 ` 2.6.3: VIA+ACPI+yenta->hang Len Brown
2004-03-11 10:27 ` Mark Hindley
2004-03-10 11:42 Mark Hindley
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox