From: sakroot@medusa.homeunix.net
To: linux-kernel@vger.kernel.org
Subject: dma error disc
Date: Sun, 25 Apr 2004 04:21:07 +0200 [thread overview]
Message-ID: <20040425022107.GA11080@sakroot.org> (raw)
In-Reply-To: <20040424210614.GA10216@sakroot.org>
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain; charset=unknown-8bit, Size: 11649 bytes --]
On Sat, Apr 24, 2004 at 11:06:14PM +0200, sakroot wrote:
> Hello i have troubles with port ide1 and my disc matrox 80gb, error dma
>
>
>
> this is error:
>
> Apr 22 13:03:02 MeDuSa kernel: hdc: dma_timer_expiry: dma status == 0x20
> Apr 22 13:03:02 MeDuSa kernel: hdc: timeout waiting for DMA
> Apr 22 13:03:02 MeDuSa kernel: hdc: timeout waiting for DMA
> Apr 22 13:03:02 MeDuSa kernel: hdc: (__ide_dma_test_irq) called while
> not waiting
> Apr 22 13:03:02 MeDuSa kernel: hdc: status error: status=0x58 {
> DriveReady SeekComplete DataRequest }
> Apr 22 13:03:02 MeDuSa kernel: hdc: drive not ready for command
> Apr 22 13:03:02 MeDuSa kernel: hdc: status timeout: status=0xd0 { Busy }
> Apr 22 13:03:02 MeDuSa kernel: hdc: drive not ready for command
> Apr 22 13:03:02 MeDuSa kernel: ide1: reset: success
> Apr 24 20:25:48 MeDuSa kernel: hdc: dma_timer_expiry: dma status == 0x20
> Apr 24 20:25:48 MeDuSa kernel: hdc: timeout waiting for DMA
> Apr 24 20:25:48 MeDuSa kernel: hdc: timeout waiting for DMA
> Apr 24 20:25:48 MeDuSa kernel: hdc: (__ide_dma_test_irq) called while
> not waiting
> Apr 24 20:25:48 MeDuSa kernel: hdc: status error: status=0x58 {
> DriveReady SeekComplete DataRequest }
> Apr 24 20:25:48 MeDuSa kernel: hdc: drive not ready for command
> Apr 24 20:25:48 MeDuSa kernel: hdc: status timeout: status=0xd0 { Busy }
> Apr 24 20:25:48 MeDuSa kernel: hdc: drive not ready for command
> Apr 24 20:25:49 MeDuSa kernel: ide1: reset: success
>
>
>
> info my system:
>
> cat /proc/version
> Linux version 2.4.24 (root@MeDuSa-C.sakroot.org) (gcc version 2.95.4
> 20011002 (Debian prerelease)) #1 lun abr 19 00:17:19 CEST 2004
>
>
>
> Linux MeDuSa.homeunix.net 2.4.24 #1 lun abr 19 00:17:19 CEST 2004 i586
> GNU/Linux
>
> Gnu C 3.3.3
> Gnu make 3.80
> util-linux 2.12
> mount 2.12
> modutils 2.4.26
> e2fsprogs 1.35
> PPP 2.4.2
> Linux C Library 2.3.2
> Dynamic linker (ldd) 2.3.2
> Procps 3.2.0
> Net-tools 1.60
> Console-tools 0.2.3
> Sh-utils 5.0.91
> Modules Loaded ipt_multiport ipt_mac ipt_MASQUERADE iptable_nat
> ip_conntrack iptable_filter ip_tables bsd_comp af_packet loop ide-cd
> cdrom hostap_plx hostap hostap_crypt
>
>
>
>
> cat /proc/cpuinfo
> processor : 0
> vendor_id : GenuineIntel
> cpu family : 5
> model : 2
> model name : Pentium 75 - 200
> stepping : 12
> cpu MHz : 132.634
> fdiv_bug : no
> hlt_bug : no
> f00f_bug : yes
> coma_bug : no
> fpu : yes
> fpu_exception : yes
> cpuid level : 1
> wp : yes
> flags : fpu vme de pse tsc msr mce cx8
> bogomips : 264.60
>
>
>
>
>
> cat /proc/modules
> ipt_multiport 632 2 (autoclean)
> ipt_mac 664 8 (autoclean)
> ipt_MASQUERADE 1304 1 (autoclean)
> iptable_nat 15672 1 (autoclean) [ipt_MASQUERADE]
> ip_conntrack 17960 1 (autoclean) [ipt_MASQUERADE
> iptable_nat]
> iptable_filter 1668 1 (autoclean)
> ip_tables 11096 7 [ipt_multiport ipt_mac ipt_MASQUERADE
> iptable_nat iptable_filter]
> bsd_comp 3992 0 (autoclean)
> af_packet 8328 3 (autoclean)
> loop 8248 0 (autoclean)
> ide-cd 28512 0
> cdrom 27200 0 [ide-cd]
> hostap_plx 43380 1
> hostap 65636 0 [hostap_plx]
> hostap_crypt 1328 0 [hostap]
>
>
>
>
>
> cat /proc/ioports
> 0000-001f : dma1
> 0020-003f : pic1
> 0040-005f : timer
> 0060-006f : keyboard
> 0080-008f : dma page reg
> 00a0-00bf : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 0170-0177 : ide1
> 01f0-01f7 : ide0
> 0376-0376 : ide1
> 03c0-03df : vga+
> 03f6-03f6 : ide0
> 0cf8-0cff : PCI conf1
> 6100-61ff : Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
> 6100-61ff : 8139too
> 6200-627f : 3Com Corporation 3c900B-TPO [Etherlink XL TPO]
> 6200-627f : 00:12.0
> 6300-637f : Standard Microsystems Corp [SMC] SMC2602W EZConnect /
> Addtron AWA-100
> 6400-643f : Standard Microsystems Corp [SMC] SMC2602W EZConnect /
> Addtron AWA-100
> 6500-651f : Realtek Semiconductor Co., Ltd. RTL-8029(AS)
> 6500-651f : ne2k-pci
> f000-f00f : Intel Corp. 82371SB PIIX3 IDE [Natoma/Triton II]
> f000-f007 : ide0
> f008-f00f : ide1
>
>
>
> cat /proc/iomem
> 00000000-0009ffff : System RAM
> 000a0000-000bffff : Video RAM area
> 000c0000-000c7fff : Video ROM
> 000f0000-000fffff : System ROM
> 00100000-07ffffff : System RAM
> 00100000-002a7ce5 : Kernel code
> 002a7ce6-002fe487 : Kernel data
> e0000000-e00000ff : Realtek Semiconductor Co., Ltd.
> RTL-8139/8139C/8139C+
> e0000000-e00000ff : 8139too
> e0001000-e000107f : 3Com Corporation 3c900B-TPO
> [Etherlink XL TPO]
> e0002000-e0002fff : Standard Microsystems Corp [SMC]
> SMC2602W EZConnect / Addtron AWA-100
> ffff0000-ffffffff : reserved
>
>
>
>
>
>
>
> lspci -vvv
>
>
>
> 00:00.0 Host bridge: Intel Corp. 430VX - 82437VX TVX [Triton VX] (rev 02)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 32
>
> 00:07.0 ISA bridge: Intel Corp. 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:07.1 IDE interface: Intel Corp. 82371SB PIIX3 IDE [Natoma/Triton II] (prog-if 80 [Master])
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Region 4: I/O ports at f000 [size=16]
>
> 00:11.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
> Subsystem: Realtek Semiconductor Co., Ltd. RT8139
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (8000ns min, 16000ns max)
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at 6100 [size=256]
> Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=256]
> Expansion ROM at <unassigned> [disabled] [size=64K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:12.0 Ethernet controller: 3Com Corporation 3c900B-TPO [Etherlink XL TPO] (rev 04)
> Subsystem: 3Com Corporation 3C900B-TPO Etherlink XL TPO 10Mb
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (2500ns min, 12000ns max), Cache Line Size: 0x08 (32 bytes)
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at 6200 [size=128]
> Region 1: Memory at e0001000 (32-bit, non-prefetchable) [size=128]
> Expansion ROM at <unassigned> [disabled] [size=128K]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:13.0 Network controller: Standard Microsystems Corp [SMC] SMC2602W EZConnect / Addtron AWA-100 (rev 02)
> Subsystem: Standard Microsystems Corp [SMC] SMC2602W EZConnect / Addtron AWA-100
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 9
> Region 1: I/O ports at 6300 [size=128]
> Region 2: Memory at e0002000 (32-bit, non-prefetchable) [size=4K]
> Region 3: I/O ports at 6400 [size=64]
>
> 00:14.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
> Subsystem: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 12
> Region 0: I/O ports at 6500 [size=32]
>
> hdparam -I /dev/hdc
>
> /dev/hdc:
>
> ATA device, with non-removable media
> Model Number: Maxtor 6Y080L0
> Serial Number: Y3LLPCHE
> Firmware Revision: YAR41BW0
> Standards:
> Supported: 7 6 5 4
> Likely used: 7
> Configuration:
> Logical max current
> cylinders 16383 16383
> heads 16 16
> sectors/track 63 63
> --
> CHS current addressable sectors: 16514064
> LBA user addressable sectors: 160086528
> device size with M = 1024*1024: 78167 MBytes
> device size with M = 1000*1000: 81964 MBytes (81 GB)
> Capabilities:
> LBA, IORDY(can be disabled)
> Queue depth: 1
> Standby timer values: spec'd by Standard, no device specific minimum
> R/W multiple sector transfer: Max = 16 Current = 16
> Advanced power management level: unknown setting (0x0000)
> Recommended acoustic management value: 192, current value: 254
> DMA: mdma0 mdma1 *mdma2 udma0 udma1 udma2 udma3 udma4 udma5 udma6
> Cycle time: min=120ns recommended=120ns
> PIO: pio0 pio1 pio2 pio3 pio4
> Cycle time: no flow control=120ns IORDY flow control=120ns
> Commands/features:
> Enabled Supported:
> * NOP cmd
> * READ BUFFER cmd
> * WRITE BUFFER cmd
> * Host Protected Area feature set
> * Look-ahead
> * Write cache
> * Power Management feature set
> Security Mode feature set
> * SMART feature set
> * FLUSH CACHE EXT command
> * Mandatory FLUSH CACHE command
> * Device Configuration Overlay feature set
> * Automatic Acoustic Management feature set
> SET MAX security extension
> Advanced Power Management feature set
> * DOWNLOAD MICROCODE cmd
> * SMART self-test
> * SMART error logging
> Security:
> Master password revision code = 65534
> supported
> not enabled
> not locked
> not frozen
> not expired: security count
> not supported: enhanced erase
> HW reset results:
> CBLID- below Vih
> Device num = 0 determined by the jumper
> Checksum: correct
>
> cat /proc/ide/drivers
> ide-cdrom version 4.59-ac1
> ide-disk version 1.17
> ide-default version 0.9.newide
>
>
>
>
> cat /proc/ide/piix
>
> Controller: 0
>
> Intel PIIX3 Chipset.
> --------------- Primary Channel ---------------- Secondary Channel -------------
> enabled enabled
> --------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------
> DMA enabled: yes no no no
> UDMA enabled: no no no no
> UDMA enabled: X X X X
> UDMA
> DMA
> PIO
>
>
>
>
>
> this is every info, if you have some troubles my mail is sakroot@medusa.homeunix.net
>
> Thanksss¡¡¡
parent reply other threads:[~2004-04-25 2:33 UTC|newest]
Thread overview: expand[flat|nested] mbox.gz Atom feed
[parent not found: <20040424210614.GA10216@sakroot.org>]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20040425022107.GA11080@sakroot.org \
--to=sakroot@medusa.homeunix.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox