From: kladit@t-online.de (Klaus Dittrich)
To: linux mailing-list <linux-kernel@vger.kernel.org>
Subject: 2.6.6-rc3 scsi symbios prevents booting
Date: Fri, 30 Apr 2004 12:42:29 +0200 [thread overview]
Message-ID: <20040430104229.GA595@xeon2.local.here> (raw)
Booting kernel-2.6.6-rc3 hangs because of the Symbios scsi-driver.
No errors with kernel-2.6.5.
(Mobo Tyan S2665, Dawicontrol DC-2964F (Chip used is AM53C974)
I get this messages .. (copied by hand from bootscreen).
Beginning Domain Validation
sym0:5 FAST SCSI 10 MB/s ST (100.0ns,offset 15)
scsi(2:0:5:0) ECHO BUFFER SIZE 5924 ist too big, trimming to 4096
scsi(2:0:5:0) Domain Validation detected failure, dropping back.
sym0:5 FAST SCSI 6.8 MB/s ST (148.0ns,offset 15)
scsi(2:0:5:0) Domain Validation detected failure, dropping back.
sym0:5:0 asynchronous
# This appeares two times
sym0:5:0 ABORT OPERATION started
sym0:5:0 ABORT OPERATION timed out
sym0:5:0 BUS RESET started
sym0:5:0 BUS RESET timed out
sym0:5:0 DEVICE RESET started
sym0:5:0 DEVICE RESET timed out
The system then hangs.
In contrast to this the messages from from kernel-2.6.5.
No errors here. All scsi-devices are working.
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11
<Adaptec AIC7902 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
(scsi0:A:9): 320.000MB/s transfers (160.000MHz DT|IU|QAS, 16bit)
(scsi0:A:10): 320.000MB/s transfers (160.000MHz DT|IU|QAS, 16bit)
Vendor: FUJITSU Model: MAP3367NC Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:9:0: Tagged Queuing enabled. Depth 32
Vendor: FUJITSU Model: MAP3367NC Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:10:0: Tagged Queuing enabled. Depth 32
scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11
<Adaptec AIC7902 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
sym0: <875> rev 0x4 at pci 0000:05:01.0 irq 22
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi2 : sym-2.1.18i
Vendor: PLEXTOR Model: CD-R PX-W1210S Rev: 1.06
Type: CD-ROM ANSI SCSI revision: 02
Vendor: EPSON Model: Perfection1640 Rev: 1.06
Type: Processor ANSI SCSI revision: 02
st: Version 20040318, fixed bufsize 32768, s/g segs 256
SCSI device sda: 71775284 512-byte hdwr sectors (36749 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2
Attached scsi disk sda at scsi0, channel 0, id 9, lun 0
SCSI device sdb: 71775284 512-byte hdwr sectors (36749 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2
Attached scsi disk sdb at scsi0, channel 0, id 10, lun 0
sym0:2: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 16)
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi2, channel 0, id 2, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 9, lun 0, type 0
Attached scsi generic sg1 at scsi0, channel 0, id 10, lun 0, type 0
Attached scsi generic sg2 at scsi2, channel 0, id 2, lun 0, type 5
Attached scsi generic sg3 at scsi2, channel 0, id 5, lun 0, type 3
Hope this helps to find the bug(s).
--
Klaus
next reply other threads:[~2004-04-30 10:43 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-04-30 10:42 Klaus Dittrich [this message]
-- strict thread matches above, loose matches on Subject: below --
2004-04-30 13:35 2.6.6-rc3 scsi symbios prevents booting Klaus Dittrich
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20040430104229.GA595@xeon2.local.here \
--to=kladit@t-online.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox