From: tabris <tabris@tabris.net>
To: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
Cc: linux-kernel@vger.kernel.org, Andrew Morton <akpm@osdl.org>,
Alan Cox <alan@lxorguk.ukuu.org.uk>
Subject: Re: undecoded slave?
Date: Thu, 23 Sep 2004 16:30:46 -0400 [thread overview]
Message-ID: <200409231630.49153.tabris@tabris.net> (raw)
In-Reply-To: <200409231314.55547.bzolnier@elka.pw.edu.pl>
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
On Thursday 23 September 2004 7:14 am, Bartlomiej Zolnierkiewicz wrote:
> [ use linux-ide@vger.kernel.org for ATA stuff ]
>
> On Thursday 23 September 2004 05:57, tabris wrote:
> > Probing IDE interface ide3...
> > hdg: Maxtor 4D060H3, ATA DISK drive
> > hdh: Maxtor 4D060H3, ATA DISK drive
> > ide-probe: ignoring undecoded slave
> >
> > Booted 2.6.9-rc2-mm2, and I no longer have an hdh. the error above
> > seems to be the only [stated] reason why.
>
> Please send hdparm -I output for both drives.
As you can see, both drives are the same brand/size/model.
Both are connected to the PDC20265 on my ASUS A7V266-E motherboard.
/dev/hdg:
ATA device, with non-removable media
Model Number: Maxtor 4D060H3
Serial Number: D3000000
Firmware Revision: DAK019K0
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 0
Supported: 6 5 4 3
Configuration:
Logical max current
cylinders 16383 65535
heads 16 1
sectors/track 63 63
--
CHS current addressable sectors: 4128705
LBA user addressable sectors: 120069936
LBA48 user addressable sectors: 120069936
device size with M = 1024*1024: 58627 MBytes
device size with M = 1000*1000: 61475 MBytes (61 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 57 Queue depth: 1
Standby timer values: spec'd by Standard, no device specific
minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0000)
Recommended acoustic management value: 192, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
* SMART feature set
* Device Configuration Overlay feature set
* 48-bit Address feature set
Automatic Acoustic Management feature set
SET MAX security extension
Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
/dev/hdh:
ATA device, with non-removable media
Model Number: Maxtor 4D060H3
Serial Number: D3000000
Firmware Revision: DAH017K0
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 0
Supported: 6 5 4 3
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 120069936
device size with M = 1024*1024: 58627 MBytes
device size with M = 1000*1000: 61475 MBytes (61 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 57 Queue depth: 1
Standby timer values: spec'd by Standard, no device specific
minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0000)
Recommended acoustic management value: 192, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
* SMART feature set
* Device Configuration Overlay feature set
Automatic Acoustic Management feature set
SET MAX security extension
Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
HW reset results:
CBLID- above Vih
Device num = 1 determined by the jumper
Checksum: correct
- --
tabris
- -
Tomorrow will be cancelled due to lack of interest.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.4 (GNU/Linux)
iD8DBQFBUzJ41U5ZaPMbKQcRAng0AJ4n5kAJCXwiO2JYu6wKa5RyS47+bQCfUisK
2d1CLQM7Lx1HlHZ6fKswZVk=
=oNxb
-----END PGP SIGNATURE-----
next prev parent reply other threads:[~2004-09-24 3:48 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-09-23 3:57 undecoded slave? tabris
2004-09-23 4:02 ` Andrew Morton
2004-09-23 7:22 ` tabris
2004-09-23 11:14 ` Bartlomiej Zolnierkiewicz
2004-09-23 20:30 ` tabris [this message]
2004-09-23 21:56 ` Alan Cox
2004-09-23 23:31 ` max file handles max David Lang
2004-09-24 0:09 ` undecoded slave? Bartlomiej Zolnierkiewicz
2004-09-24 1:41 ` Eric Mudama
2004-09-24 8:26 ` tabris
2004-09-24 16:29 ` Eric Mudama
2004-09-24 8:24 ` tabris
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200409231630.49153.tabris@tabris.net \
--to=tabris@tabris.net \
--cc=akpm@osdl.org \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=bzolnier@elka.pw.edu.pl \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox