ide0=ata66 obsolete, but replaced by what (2.6.10)?

ide0=ata66 obsolete, but replaced by what (2.6.10)?

[Ralf Hildebrandt]

Ever since a few kernels ago, my dmesg output says:

Kernel command line: BOOT_IMAGE=Linux ro root=303 noapic ide0=ata66 video=vesafb:mtrr,ywrap
ide_setup: ide0=ata66 -- OBSOLETE OPTION, WILL BE REMOVED SOON!

OK, but what is it replaced with?
Because later on, dmesg also says:

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller
    ide0: BM-DMA at 0x2080-0x2087, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x2088-0x208f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST94019A, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SD-R6252, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3
	 

My question is now:

1) What replaces the boot option "ide0=ata66"?
or
2) How do I get the old bus speed back?

-- 
Ralf Hildebrandt (i.A. des IT-Zentrum)          Ralf.Hildebrandt@charite.de
Charite - Universitätsmedizin Berlin            Tel.  +49 (0)30-450 570-155
Gemeinsame Einrichtung von FU- und HU-Berlin    Fax.  +49 (0)30-450 570-962
IT-Zentrum Standort CBF                 send no mail to spamtrap@charite.de

Re: ide0=ata66 obsolete, but replaced by what (2.6.10)?

[Bartlomiej Zolnierkiewicz]

Hi,

On Sun, 26 Dec 2004 19:58:30 +0100, Ralf Hildebrandt
<Ralf.Hildebrandt@charite.de> wrote:
> Ever since a few kernels ago, my dmesg output says:
> 
> Kernel command line: BOOT_IMAGE=Linux ro root=303 noapic ide0=ata66 video=vesafb:mtrr,ywrap
> ide_setup: ide0=ata66 -- OBSOLETE OPTION, WILL BE REMOVED SOON!
> 
> OK, but what is it replaced with?
> Because later on, dmesg also says:
> 
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
> NFORCE3-150: chipset revision 165
> NFORCE3-150: not 100% native mode: will probe irqs later
> NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround.
> NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller
>     ide0: BM-DMA at 0x2080-0x2087, BIOS settings: hda:DMA, hdb:pio
>     ide1: BM-DMA at 0x2088-0x208f, BIOS settings: hdc:DMA, hdd:pio
> Probing IDE interface ide0...
> hda: ST94019A, ATA DISK drive
> elevator: using anticipatory as default io scheduler
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Probing IDE interface ide1...
> hdc: SD-R6252, ATAPI CD/DVD-ROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: max request size: 1024KiB
> hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
> hda: cache flushes supported
>  /dev/ide/host0/bus0/target0/lun0: p1 p2 p3
> 
> My question is now:
> 
> 1) What replaces the boot option "ide0=ata66"?

Nothing ;-), what do you need it for?

> or
> 2) How do I get the old bus speed back?

What bus speed are you talking about?

"idebus=" is still there but you don't need to use it for nVidia chipsets AFAIK.

Bartlomiej