* OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
@ 2005-07-06 10:11 Jeremy Laine
2005-07-06 14:44 ` Michael Krufky
2005-07-06 14:59 ` Alexey Dobriyan
0 siblings, 2 replies; 18+ messages in thread
From: Jeremy Laine @ 2005-07-06 10:11 UTC (permalink / raw)
To: linux-kernel
Hi!
I keep getting OOPS's when using a Bt878 TV card, I am basically unable to watch
TV for more than about 20-30mn without my system grinding to a halt. If I do not
make use of the bttv module, the system is perfectly stable. I saw the bttv
module is marked as "Orphan" in the MAINTAINERS file which is why I am writing
straight to the LKML, do not hesitate to correct me if this is wrong!
I have seen suggestions to try without PREEMPT enabled, which I will be doing
shortly. Any other suggestions to get to the bottom of this problem are most
welcome!
The OOPS on 2.6.12 goes like so:
Jul 6 10:43:58 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
(44-958)
Jul 6 10:45:15 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
(44-958)
Jul 6 10:55:44 sharky kernel: Unable to handle kernel paging request at virtual
address 0386c028
Jul 6 10:55:44 sharky kernel: printing eip:
Jul 6 10:55:44 sharky kernel: c0162ac6
Jul 6 10:55:44 sharky kernel: *pde = 00000000
Jul 6 10:55:44 sharky kernel: Oops: 0000 [#1]
Jul 6 10:55:44 sharky kernel: PREEMPT
Jul 6 10:55:44 sharky kernel: Modules linked in: nls_iso8859_1 nls_cp437 vfat
fat usb_storage vmnet vmmon lp ipt_TOS iptable_mangle ipt_MASQUERADE
ipt_multiport ipt_REJECT ipt_LOG ipt_limit ipt_state iptable_filter parport_pc
parport intel_agp 3c59x mii snd_bt87x tuner tda9887 msp3400 bttv video_buf
firmware_class btcx_risc tveeprom sk98lin tun snd_pcm_oss snd_mixer_oss
snd_intel8x0 snd_emu10k1 snd_rawmidi snd_seq_device snd_ac97_codec snd_pcm
snd_timer snd_page_alloc snd_util_mem snd_hwdep snd soundcore ip_nat_ftp
iptable_nat ip_tables ip_conntrack_ftp ip_conntrack nvidia usblp
Jul 6 10:55:44 sharky kernel: CPU: 0
Jul 6 10:55:44 sharky kernel: EIP: 0060:[__link_path_walk+1862/3520]
Tainted: P VLI
Jul 6 10:55:44 sharky kernel: EFLAGS: 00010206 (2.6.12)
Jul 6 10:55:44 sharky kernel: EIP is at __link_path_walk+0x746/0xdc0
Jul 6 10:55:44 sharky kernel: eax: 0386c000 ebx: d5c3f003 ecx: 00000000
edx: c79e46b4
Jul 6 10:55:44 sharky kernel: esi: 00000000 edi: ceac50b8 ebp: c7b85f10
esp: c7b85e1c
Jul 6 10:55:44 sharky kernel: ds: 007b es: 007b ss: 0068
Jul 6 10:55:44 sharky kernel: Process sylpheed-claws (pid: 12722,
threadinfo=c7b84000 task=cd51f020)
Jul 6 10:55:44 sharky kernel: Stack: c7b85f10 c7b85e4c c7b85e44 f6696700
00000000 c0156aab f6696700 0031f129
Jul 6 10:55:44 sharky kernel: 00001000 00000001 c17e0c80 c79e46b4
0011a425 00000003 d5c3f000 df56d0dc
Jul 6 10:55:44 sharky kernel: c7b85f10 c7b85f50 c7b85eb8 c7b85e78
c0163187 df56d0dc d5c3f000 df56d0dc
Jul 6 10:55:44 sharky kernel: Call Trace:
Jul 6 10:55:44 sharky kernel: [__getblk+43/96] __getblk+0x2b/0x60
Jul 6 10:55:44 sharky kernel: [link_path_walk+71/224] link_path_walk+0x47/0xe0
Jul 6 10:55:44 sharky kernel: [path_lookup+127/320] path_lookup+0x7f/0x140
Jul 6 10:55:44 sharky kernel: [__user_walk+51/96] __user_walk+0x33/0x60
Jul 6 10:55:44 sharky kernel: [vfs_stat+31/96] vfs_stat+0x1f/0x60
Jul 6 10:55:44 sharky kernel: [sys_stat64+27/64] sys_stat64+0x1b/0x40
Jul 6 10:55:44 sharky kernel: [schedule+228/1568] schedule+0xe4/0x620
Jul 6 10:55:44 sharky kernel: [do_gettimeofday+26/208]
do_gettimeofday+0x1a/0xd0
Jul 6 10:55:44 sharky kernel: [sys_time+23/64] sys_time+0x17/0x40
Jul 6 10:55:44 sharky kernel: [syscall_call+7/11] syscall_call+0x7/0xb
Jul 6 10:55:44 sharky kernel: Code: fb ff ff f6 44 24 24 01 8b 54 24 2c 8b 7a
08 0f 84 44 03 00 00 85 ff 0f 84 3c 03 00 00 8b 87 8c 00 00 00 85 c0 0f 84 2e
03 00 00 <8b> 70 28 85 f6 0f 84 23 03 00 00 bb 00 e0 ff ff 21 e3 8b 03 83
Below is some information about my environment:
---[ /proc/cpuinfo ]---
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Pentium(R) 4 CPU 2.80GHz
stepping : 9
cpu MHz : 2807.248
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36
clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr
bogomips : 5537.79
---[ /proc/modules ]---
vmnet 32420 3 - Live 0xf8bd2000
vmmon 172076 0 - Live 0xf8bf0000
lp 11588 0 - Live 0xf8bc3000
ipt_TOS 2688 1 - Live 0xf8bc1000
iptable_mangle 2944 1 - Live 0xf8bb1000
ipt_MASQUERADE 3584 1 - Live 0xf8bba000
ipt_multiport 2688 4 - Live 0xf8b6f000
ipt_REJECT 5248 4 - Live 0xf8bb4000
ipt_LOG 7296 4 - Live 0xf8b9d000
ipt_limit 2560 4 - Live 0xf8b9b000
ipt_state 2048 13 - Live 0xf8b71000
iptable_filter 3200 1 - Live 0xf8b19000
parport_pc 36036 1 - Live 0xf8b51000
parport 25664 2 lp,parport_pc, Live 0xf8b67000
usblp 13312 0 - Live 0xf8b4c000
intel_agp 23580 1 - Live 0xf8aff000
3c59x 42152 0 - Live 0xf8b5b000
mii 5760 1 3c59x, Live 0xf8afc000
snd_bt87x 15048 0 - Live 0xf8b0f000
tuner 28712 0 - Live 0xf8b06000
tda9887 14360 0 - Live 0xf8ad5000
msp3400 27944 0 - Live 0xf8aed000
bttv 157968 0 - Live 0xf8b73000
video_buf 22404 1 bttv, Live 0xf8af5000
firmware_class 10496 1 bttv, Live 0xf8ada000
btcx_risc 5128 1 bttv, Live 0xf8abd000
tveeprom 13464 1 bttv, Live 0xf8998000
sk98lin 177248 0 - Live 0xf8b1f000
tun 11776 2 - Live 0xf89b5000
snd_pcm_oss 53536 0 - Live 0xf8ade000
snd_mixer_oss 19840 1 snd_pcm_oss, Live 0xf8ab7000
snd_intel8x0 33984 0 - Live 0xf8ac3000
snd_emu10k1 118788 0 - Live 0xf8a33000
snd_rawmidi 25888 1 snd_emu10k1, Live 0xf89c6000
snd_seq_device 8844 2 snd_emu10k1,snd_rawmidi, Live 0xf89a1000
snd_ac97_codec 83320 2 snd_intel8x0,snd_emu10k1, Live 0xf89fb000
snd_pcm 95240 5 snd_bt87x,snd_pcm_oss,snd_intel8x0,snd_emu10k1,snd_ac97_codec,
Live 0xf89e2000
snd_timer 25860 2 snd_emu10k1,snd_pcm, Live 0xf89be000
snd_page_alloc 10244 4 snd_bt87x,snd_intel8x0,snd_emu10k1,snd_pcm, Live
0xf899d000
snd_util_mem 4736 1 snd_emu10k1, Live 0xf898b000
snd_hwdep 9504 1 snd_emu10k1, Live 0xf8994000
snd 54756 11
snd_bt87x,snd_pcm_oss,snd_mixer_oss,snd_intel8x0,snd_emu10k1,snd_rawmidi,snd_seq_device,snd_ac97_codec,snd_pcm,snd_timer,snd_hwdep,
Live 0xf89a6000
soundcore 10464 1 snd, Live 0xf8990000
ip_nat_ftp 3712 0 - Live 0xf8949000
iptable_nat 24028 3 ipt_MASQUERADE,ip_nat_ftp, Live 0xf8973000
ip_tables 22400 10
ipt_TOS,iptable_mangle,ipt_MASQUERADE,ipt_multiport,ipt_REJECT,ipt_LOG,ipt_limit,ipt_state,iptable_filter,iptable_nat,
Live 0xf894c000
ip_conntrack_ftp 73104 1 ip_nat_ftp, Live 0xf8960000
ip_conntrack 45752 5
ipt_MASQUERADE,ipt_state,ip_nat_ftp,iptable_nat,ip_conntrack_ftp, Live
0xf8953000
nvidia 3922812 12 - Live 0xf8d3b000
---[ /proc/ioports ]---
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0290-0297 : pnp 00:0a
02f8-02ff : serial
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial
0400-041f : 0000:00:1f.3
0400-040f : i801-smbus
0480-04bf : 0000:00:1f.0
0680-06ff : pnp 00:0a
0800-087f : 0000:00:1f.0
0800-0803 : PM1a_EVT_BLK
0804-0805 : PM1a_CNT_BLK
0808-080b : PM_TMR
0828-082f : GPE0_BLK
0cf8-0cff : PCI conf1
b000-b0ff : 0000:00:1f.5
b000-b0ff : Intel ICH5
b400-b43f : 0000:00:1f.5
b400-b43f : Intel ICH5
b480-b49f : 0000:00:1d.0
b480-b49f : uhci_hcd
b800-b81f : 0000:00:1d.1
b800-b81f : uhci_hcd
b880-b89f : 0000:00:1d.2
b880-b89f : uhci_hcd
bc00-bc1f : 0000:00:1d.3
bc00-bc1f : uhci_hcd
c880-c8ff : 0000:02:0c.0
c880-c8ff : 0000:02:0c.0
cc00-cc1f : 0000:02:0b.0
cc00-cc1f : EMU10K1
d000-d007 : 0000:02:0b.1
d000-d007 : emu10k1-gp
d080-d08f : 0000:02:09.0
d400-d403 : 0000:02:09.0
d480-d487 : 0000:02:09.0
d800-d8ff : 0000:02:05.0
d800-d8ff : SysKonnect SK-98xx
dc00-dc03 : 0000:02:09.0
e000-e007 : 0000:02:09.0
e080-e08f : 0000:02:04.0
e400-e403 : 0000:02:04.0
e480-e487 : 0000:02:04.0
e800-e803 : 0000:02:04.0
e880-e887 : 0000:02:04.0
ec00-ec7f : 0000:02:03.0
fc00-fc0f : 0000:00:1f.1
fc00-fc07 : ide0
fc08-fc0f : ide1
---[ /proc/iomem ]---
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000ce800-000d2bff : Adapter ROM
000d3000-000d37ff : Adapter ROM
000f0000-000fffff : System ROM
00100000-3ff2ffff : System RAM
00100000-0035a10c : Kernel code
0035a10d-0045ab7f : Kernel data
3ff30000-3ff3ffff : ACPI Tables
3ff40000-3ffeffff : ACPI Non-volatile Storage
3fff0000-3fffffff : reserved
40000000-400003ff : 0000:00:1f.1
e0000000-f3efffff : PCI Bus #01
e0000000-efffffff : 0000:01:00.0
f3ffe000-f3ffefff : 0000:02:0a.0
f3ffe000-f3ffefff : bttv0
f3fff000-f3ffffff : 0000:02:0a.1
f4fff400-f4fff4ff : 0000:00:1f.5
f4fff400-f4fff4ff : Intel ICH5
f4fff800-f4fff9ff : 0000:00:1f.5
f4fff800-f4fff9ff : Intel ICH5
f4fffc00-f4ffffff : 0000:00:1d.7
f4fffc00-f4ffffff : ehci_hcd
f5000000-f7efffff : PCI Bus #01
f5000000-f5ffffff : 0000:01:00.0
f6000000-f6ffffff : 0000:01:00.0
f6000000-f6ffffff : nvidia
f7ff4000-f7ff7fff : 0000:02:05.0
f7ff4000-f7ff7fff : SysKonnect SK-98xx
f7fff000-f7fff07f : 0000:02:0c.0
f7fff400-f7fff4ff : 0000:02:09.0
f7fff400-f7fff4ff : SiI680
f7fff800-f7ffffff : 0000:02:03.0
f8000000-fbffffff : 0000:00:00.0
ffb80000-ffffffff : reserved
---[ lspci -vvv ]---
0000:00:00.0 Host bridge: Intel Corp. 82865G/PE/P DRAM Controller/Host-Hub
Interface (rev 02)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] #09 [2106]
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+
Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
0000:00:01.0 PCI bridge: Intel Corp. 82865G/PE/P PCI to AGP Controller (rev 02)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f5000000-f7efffff
Prefetchable memory behind bridge: e0000000-f3efffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at b480 [size=32]
0000:00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at b800 [size=32]
0000:00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b880 [size=32]
0000:00:1d.3 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at bc00 [size=32]
0000:00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI
Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at f4fffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [20a0]
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000c000-0000efff
Memory behind bridge: f7f00000-fbffffff
Prefetchable memory behind bridge: f3f00000-f3ffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
0000:00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Bridge (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) Ultra ATA 100
Storage Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
0000:00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev
02)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 0400 [size=32]
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801EB/ER (ICH5/ICH5R)
AC'97 Audio Controller (rev 02)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at b000 [size=256]
Region 1: I/O ports at b400 [size=64]
Region 2: Memory at f4fff800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at f4fff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:00.0 VGA compatible controller: nVidia Corporation NV40 OS1RT00B30 (rev
a1) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 817b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 2: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at f7ee0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+
AGP3+ Rate=x4,x8
Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
0000:02:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 46) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 808a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size: 0x04 (16 bytes)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f7fff800 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at ec00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:04.0 RAID bus controller: VIA Technologies, Inc. VT6410 ATA133 RAID
controller (rev 06)
Subsystem: Asustek Computer, Inc.: Unknown device 80f4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e880 [size=8]
Region 1: I/O ports at e800 [size=4]
Region 2: I/O ports at e480 [size=8]
Region 3: I/O ports at e400 [size=4]
Region 4: I/O ports at e080 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:05.0 Ethernet controller: 3Com Corporation 3c940 10/100/1000Base-T
[Marvell] (rev 12)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 0x04 (16 bytes)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f7ff4000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at d800 [size=256]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
0000:02:09.0 RAID bus controller: Silicon Image, Inc. (formerly CMD Technology
Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) Winic W-680
(Silicon Image 680 based)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x01 (4 bytes)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at e000 [size=8]
Region 1: I/O ports at dc00 [size=4]
Region 2: I/O ports at d480 [size=8]
Region 3: I/O ports at d400 [size=4]
Region 4: I/O ports at d080 [size=16]
Region 5: Memory at f7fff400 (32-bit, non-prefetchable) [size=256]
Expansion ROM at f7f00000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:02:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f3ffe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver, audio
section)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f3fff000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev
08)
Subsystem: Creative Labs CT4850 SBLive! Value
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at cc00 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0b.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev
08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Region 0: I/O ports at d000 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev
74)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 0x04 (16 bytes)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at c880 [size=128]
Region 1: Memory at f7fff000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at f7fc0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Thanks in advance for any pointers!
Jeremy
--
http://www.jerryweb.org/ : JerryWeb.org
http://sailcut.sourceforge.net/ : Sailcut CAD
http://mpf70.sourceforge.net/ : MPman MP-F70 support for Linux
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-06 10:11 OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12) Jeremy Laine
@ 2005-07-06 14:44 ` Michael Krufky
2005-07-07 14:31 ` Lee Revell
2005-07-06 14:59 ` Alexey Dobriyan
1 sibling, 1 reply; 18+ messages in thread
From: Michael Krufky @ 2005-07-06 14:44 UTC (permalink / raw)
To: Jeremy Laine; +Cc: linux-kernel, Mauro Carvalho Chehab, Linux and Kernel Video
bttv is now maintained by Mauro Carvalho Chehab
<mchehab@brturbo.com.br>, as part of the video4linux project. I am
forwarding this to Mauro and the video4linux list. Linux and Kernel
Video <video4linux-list@redhat.com>
Jeremy Laine wrote:
>Hi!
>
>I keep getting OOPS's when using a Bt878 TV card, I am basically unable to watch
>TV for more than about 20-30mn without my system grinding to a halt. If I do not
>make use of the bttv module, the system is perfectly stable. I saw the bttv
>module is marked as "Orphan" in the MAINTAINERS file which is why I am writing
>straight to the LKML, do not hesitate to correct me if this is wrong!
>
>I have seen suggestions to try without PREEMPT enabled, which I will be doing
>shortly. Any other suggestions to get to the bottom of this problem are most
>welcome!
>
>The OOPS on 2.6.12 goes like so:
>
>Jul 6 10:43:58 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
>(44-958)
>Jul 6 10:45:15 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
>(44-958)
>Jul 6 10:55:44 sharky kernel: Unable to handle kernel paging request at virtual
>address 0386c028
>Jul 6 10:55:44 sharky kernel: printing eip:
>Jul 6 10:55:44 sharky kernel: c0162ac6
>Jul 6 10:55:44 sharky kernel: *pde = 00000000
>Jul 6 10:55:44 sharky kernel: Oops: 0000 [#1]
>Jul 6 10:55:44 sharky kernel: PREEMPT
>Jul 6 10:55:44 sharky kernel: Modules linked in: nls_iso8859_1 nls_cp437 vfat
>fat usb_storage vmnet vmmon lp ipt_TOS iptable_mangle ipt_MASQUERADE
>ipt_multiport ipt_REJECT ipt_LOG ipt_limit ipt_state iptable_filter parport_pc
>parport intel_agp 3c59x mii snd_bt87x tuner tda9887 msp3400 bttv video_buf
>firmware_class btcx_risc tveeprom sk98lin tun snd_pcm_oss snd_mixer_oss
>snd_intel8x0 snd_emu10k1 snd_rawmidi snd_seq_device snd_ac97_codec snd_pcm
>snd_timer snd_page_alloc snd_util_mem snd_hwdep snd soundcore ip_nat_ftp
>iptable_nat ip_tables ip_conntrack_ftp ip_conntrack nvidia usblp
>Jul 6 10:55:44 sharky kernel: CPU: 0
>Jul 6 10:55:44 sharky kernel: EIP: 0060:[__link_path_walk+1862/3520]
>Tainted: P VLI
>Jul 6 10:55:44 sharky kernel: EFLAGS: 00010206 (2.6.12)
>Jul 6 10:55:44 sharky kernel: EIP is at __link_path_walk+0x746/0xdc0
>Jul 6 10:55:44 sharky kernel: eax: 0386c000 ebx: d5c3f003 ecx: 00000000
>edx: c79e46b4
>Jul 6 10:55:44 sharky kernel: esi: 00000000 edi: ceac50b8 ebp: c7b85f10
>esp: c7b85e1c
>Jul 6 10:55:44 sharky kernel: ds: 007b es: 007b ss: 0068
>Jul 6 10:55:44 sharky kernel: Process sylpheed-claws (pid: 12722,
>threadinfo=c7b84000 task=cd51f020)
>Jul 6 10:55:44 sharky kernel: Stack: c7b85f10 c7b85e4c c7b85e44 f6696700
>00000000 c0156aab f6696700 0031f129
>Jul 6 10:55:44 sharky kernel: 00001000 00000001 c17e0c80 c79e46b4
>0011a425 00000003 d5c3f000 df56d0dc
>Jul 6 10:55:44 sharky kernel: c7b85f10 c7b85f50 c7b85eb8 c7b85e78
>c0163187 df56d0dc d5c3f000 df56d0dc
>Jul 6 10:55:44 sharky kernel: Call Trace:
>Jul 6 10:55:44 sharky kernel: [__getblk+43/96] __getblk+0x2b/0x60
>Jul 6 10:55:44 sharky kernel: [link_path_walk+71/224] link_path_walk+0x47/0xe0
>Jul 6 10:55:44 sharky kernel: [path_lookup+127/320] path_lookup+0x7f/0x140
>Jul 6 10:55:44 sharky kernel: [__user_walk+51/96] __user_walk+0x33/0x60
>Jul 6 10:55:44 sharky kernel: [vfs_stat+31/96] vfs_stat+0x1f/0x60
>Jul 6 10:55:44 sharky kernel: [sys_stat64+27/64] sys_stat64+0x1b/0x40
>Jul 6 10:55:44 sharky kernel: [schedule+228/1568] schedule+0xe4/0x620
>Jul 6 10:55:44 sharky kernel: [do_gettimeofday+26/208]
>do_gettimeofday+0x1a/0xd0
>Jul 6 10:55:44 sharky kernel: [sys_time+23/64] sys_time+0x17/0x40
>Jul 6 10:55:44 sharky kernel: [syscall_call+7/11] syscall_call+0x7/0xb
>Jul 6 10:55:44 sharky kernel: Code: fb ff ff f6 44 24 24 01 8b 54 24 2c 8b 7a
>08 0f 84 44 03 00 00 85 ff 0f 84 3c 03 00 00 8b 87 8c 00 00 00 85 c0 0f 84 2e
>03 00 00 <8b> 70 28 85 f6 0f 84 23 03 00 00 bb 00 e0 ff ff 21 e3 8b 03 83
>
>Below is some information about my environment:
>
>---[ /proc/cpuinfo ]---
>
>processor : 0
>vendor_id : GenuineIntel
>cpu family : 15
>model : 2
>model name : Intel(R) Pentium(R) 4 CPU 2.80GHz
>stepping : 9
>cpu MHz : 2807.248
>cache size : 512 KB
>fdiv_bug : no
>hlt_bug : no
>f00f_bug : no
>coma_bug : no
>fpu : yes
>fpu_exception : yes
>cpuid level : 2
>wp : yes
>flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36
>clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr
>bogomips : 5537.79
>
>
>---[ /proc/modules ]---
>
>vmnet 32420 3 - Live 0xf8bd2000
>vmmon 172076 0 - Live 0xf8bf0000
>lp 11588 0 - Live 0xf8bc3000
>ipt_TOS 2688 1 - Live 0xf8bc1000
>iptable_mangle 2944 1 - Live 0xf8bb1000
>ipt_MASQUERADE 3584 1 - Live 0xf8bba000
>ipt_multiport 2688 4 - Live 0xf8b6f000
>ipt_REJECT 5248 4 - Live 0xf8bb4000
>ipt_LOG 7296 4 - Live 0xf8b9d000
>ipt_limit 2560 4 - Live 0xf8b9b000
>ipt_state 2048 13 - Live 0xf8b71000
>iptable_filter 3200 1 - Live 0xf8b19000
>parport_pc 36036 1 - Live 0xf8b51000
>parport 25664 2 lp,parport_pc, Live 0xf8b67000
>usblp 13312 0 - Live 0xf8b4c000
>intel_agp 23580 1 - Live 0xf8aff000
>3c59x 42152 0 - Live 0xf8b5b000
>mii 5760 1 3c59x, Live 0xf8afc000
>snd_bt87x 15048 0 - Live 0xf8b0f000
>tuner 28712 0 - Live 0xf8b06000
>tda9887 14360 0 - Live 0xf8ad5000
>msp3400 27944 0 - Live 0xf8aed000
>bttv 157968 0 - Live 0xf8b73000
>video_buf 22404 1 bttv, Live 0xf8af5000
>firmware_class 10496 1 bttv, Live 0xf8ada000
>btcx_risc 5128 1 bttv, Live 0xf8abd000
>tveeprom 13464 1 bttv, Live 0xf8998000
>sk98lin 177248 0 - Live 0xf8b1f000
>tun 11776 2 - Live 0xf89b5000
>snd_pcm_oss 53536 0 - Live 0xf8ade000
>snd_mixer_oss 19840 1 snd_pcm_oss, Live 0xf8ab7000
>snd_intel8x0 33984 0 - Live 0xf8ac3000
>snd_emu10k1 118788 0 - Live 0xf8a33000
>snd_rawmidi 25888 1 snd_emu10k1, Live 0xf89c6000
>snd_seq_device 8844 2 snd_emu10k1,snd_rawmidi, Live 0xf89a1000
>snd_ac97_codec 83320 2 snd_intel8x0,snd_emu10k1, Live 0xf89fb000
>snd_pcm 95240 5 snd_bt87x,snd_pcm_oss,snd_intel8x0,snd_emu10k1,snd_ac97_codec,
>Live 0xf89e2000
>snd_timer 25860 2 snd_emu10k1,snd_pcm, Live 0xf89be000
>snd_page_alloc 10244 4 snd_bt87x,snd_intel8x0,snd_emu10k1,snd_pcm, Live
>0xf899d000
>snd_util_mem 4736 1 snd_emu10k1, Live 0xf898b000
>snd_hwdep 9504 1 snd_emu10k1, Live 0xf8994000
>snd 54756 11
>snd_bt87x,snd_pcm_oss,snd_mixer_oss,snd_intel8x0,snd_emu10k1,snd_rawmidi,snd_seq_device,snd_ac97_codec,snd_pcm,snd_timer,snd_hwdep,
>Live 0xf89a6000
>soundcore 10464 1 snd, Live 0xf8990000
>ip_nat_ftp 3712 0 - Live 0xf8949000
>iptable_nat 24028 3 ipt_MASQUERADE,ip_nat_ftp, Live 0xf8973000
>ip_tables 22400 10
>ipt_TOS,iptable_mangle,ipt_MASQUERADE,ipt_multiport,ipt_REJECT,ipt_LOG,ipt_limit,ipt_state,iptable_filter,iptable_nat,
>Live 0xf894c000
>ip_conntrack_ftp 73104 1 ip_nat_ftp, Live 0xf8960000
>ip_conntrack 45752 5
>ipt_MASQUERADE,ipt_state,ip_nat_ftp,iptable_nat,ip_conntrack_ftp, Live
>0xf8953000
>nvidia 3922812 12 - Live 0xf8d3b000
>
>
>---[ /proc/ioports ]---
>
>0000-001f : dma1
>0020-0021 : pic1
>0040-0043 : timer0
>0050-0053 : timer1
>0060-006f : keyboard
>0070-0077 : rtc
>0080-008f : dma page reg
>00a0-00a1 : pic2
>00c0-00df : dma2
>00f0-00ff : fpu
>0170-0177 : ide1
>01f0-01f7 : ide0
>0290-0297 : pnp 00:0a
>02f8-02ff : serial
>0376-0376 : ide1
>0378-037a : parport0
>03c0-03df : vga+
>03f6-03f6 : ide0
>03f8-03ff : serial
>0400-041f : 0000:00:1f.3
> 0400-040f : i801-smbus
>0480-04bf : 0000:00:1f.0
>0680-06ff : pnp 00:0a
>0800-087f : 0000:00:1f.0
> 0800-0803 : PM1a_EVT_BLK
> 0804-0805 : PM1a_CNT_BLK
> 0808-080b : PM_TMR
> 0828-082f : GPE0_BLK
>0cf8-0cff : PCI conf1
>b000-b0ff : 0000:00:1f.5
> b000-b0ff : Intel ICH5
>b400-b43f : 0000:00:1f.5
> b400-b43f : Intel ICH5
>b480-b49f : 0000:00:1d.0
> b480-b49f : uhci_hcd
>b800-b81f : 0000:00:1d.1
> b800-b81f : uhci_hcd
>b880-b89f : 0000:00:1d.2
> b880-b89f : uhci_hcd
>bc00-bc1f : 0000:00:1d.3
> bc00-bc1f : uhci_hcd
>c880-c8ff : 0000:02:0c.0
> c880-c8ff : 0000:02:0c.0
>cc00-cc1f : 0000:02:0b.0
> cc00-cc1f : EMU10K1
>d000-d007 : 0000:02:0b.1
> d000-d007 : emu10k1-gp
>d080-d08f : 0000:02:09.0
>d400-d403 : 0000:02:09.0
>d480-d487 : 0000:02:09.0
>d800-d8ff : 0000:02:05.0
> d800-d8ff : SysKonnect SK-98xx
>dc00-dc03 : 0000:02:09.0
>e000-e007 : 0000:02:09.0
>e080-e08f : 0000:02:04.0
>e400-e403 : 0000:02:04.0
>e480-e487 : 0000:02:04.0
>e800-e803 : 0000:02:04.0
>e880-e887 : 0000:02:04.0
>ec00-ec7f : 0000:02:03.0
>fc00-fc0f : 0000:00:1f.1
> fc00-fc07 : ide0
> fc08-fc0f : ide1
>
>
>---[ /proc/iomem ]---
>
>00000000-0009fbff : System RAM
>0009fc00-0009ffff : reserved
>000a0000-000bffff : Video RAM area
>000c0000-000c7fff : Video ROM
>000ce800-000d2bff : Adapter ROM
>000d3000-000d37ff : Adapter ROM
>000f0000-000fffff : System ROM
>00100000-3ff2ffff : System RAM
> 00100000-0035a10c : Kernel code
> 0035a10d-0045ab7f : Kernel data
>3ff30000-3ff3ffff : ACPI Tables
>3ff40000-3ffeffff : ACPI Non-volatile Storage
>3fff0000-3fffffff : reserved
>40000000-400003ff : 0000:00:1f.1
>e0000000-f3efffff : PCI Bus #01
> e0000000-efffffff : 0000:01:00.0
>f3ffe000-f3ffefff : 0000:02:0a.0
> f3ffe000-f3ffefff : bttv0
>f3fff000-f3ffffff : 0000:02:0a.1
>f4fff400-f4fff4ff : 0000:00:1f.5
> f4fff400-f4fff4ff : Intel ICH5
>f4fff800-f4fff9ff : 0000:00:1f.5
> f4fff800-f4fff9ff : Intel ICH5
>f4fffc00-f4ffffff : 0000:00:1d.7
> f4fffc00-f4ffffff : ehci_hcd
>f5000000-f7efffff : PCI Bus #01
> f5000000-f5ffffff : 0000:01:00.0
> f6000000-f6ffffff : 0000:01:00.0
> f6000000-f6ffffff : nvidia
>f7ff4000-f7ff7fff : 0000:02:05.0
> f7ff4000-f7ff7fff : SysKonnect SK-98xx
>f7fff000-f7fff07f : 0000:02:0c.0
>f7fff400-f7fff4ff : 0000:02:09.0
> f7fff400-f7fff4ff : SiI680
>f7fff800-f7ffffff : 0000:02:03.0
>f8000000-fbffffff : 0000:00:00.0
>ffb80000-ffffffff : reserved
>
>
>---[ lspci -vvv ]---
>
>0000:00:00.0 Host bridge: Intel Corp. 82865G/PE/P DRAM Controller/Host-Hub
>Interface (rev 02)
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
><MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
> Capabilities: [e4] #09 [2106]
> Capabilities: [a0] AGP version 3.0
> Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+
>Rate=x4,x8
> Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
>
>0000:00:01.0 PCI bridge: Intel Corp. 82865G/PE/P PCI to AGP Controller (rev 02)
>(prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: f5000000-f7efffff
> Prefetchable memory behind bridge: e0000000-f3efffff
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
>
>0000:00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1
>(rev 02) (prog-if 00 [UHCI])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> Region 4: I/O ports at b480 [size=32]
>
>0000:00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2
>(rev 02) (prog-if 00 [UHCI])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 19
> Region 4: I/O ports at b800 [size=32]
>
>0000:00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3
>(rev 02) (prog-if 00 [UHCI])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin C routed to IRQ 18
> Region 4: I/O ports at b880 [size=32]
>
>0000:00:1d.3 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4
>(rev 02) (prog-if 00 [UHCI])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> Region 4: I/O ports at bc00 [size=32]
>
>0000:00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI
>Controller (rev 02) (prog-if 20 [EHCI])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 23
> Region 0: Memory at f4fffc00 (32-bit, non-prefetchable) [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] #0a [20a0]
>
>0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2) (prog-if 00
>[Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> I/O behind bridge: 0000c000-0000efff
> Memory behind bridge: f7f00000-fbffffff
> Prefetchable memory behind bridge: f3f00000-f3ffffff
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
>
>0000:00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Bridge (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
>SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 0
>
>0000:00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) Ultra ATA 100
>Storage Controller (rev 02) (prog-if 8a [Master SecP PriP])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 18
> Region 0: I/O ports at <unassigned>
> Region 1: I/O ports at <unassigned>
> Region 2: I/O ports at <unassigned>
> Region 3: I/O ports at <unassigned>
> Region 4: I/O ports at fc00 [size=16]
> Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
>
>0000:00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev
>02)
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 5
> Region 4: I/O ports at 0400 [size=32]
>
>0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801EB/ER (ICH5/ICH5R)
>AC'97 Audio Controller (rev 02)
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 17
> Region 0: I/O ports at b000 [size=256]
> Region 1: I/O ports at b400 [size=64]
> Region 2: Memory at f4fff800 (32-bit, non-prefetchable) [size=512]
> Region 3: Memory at f4fff400 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:01:00.0 VGA compatible controller: nVidia Corporation NV40 OS1RT00B30 (rev
>a1) (prog-if 00 [VGA])
> Subsystem: Asustek Computer, Inc.: Unknown device 817b
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 248 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M]
> Region 2: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
> Expansion ROM at f7ee0000 [disabled] [size=128K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 3.0
> Status: RQ=256 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+
>AGP3+ Rate=x4,x8
> Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
>
>0000:02:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
>Controller (rev 46) (prog-if 10 [OHCI])
> Subsystem: Asustek Computer, Inc.: Unknown device 808a
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 64 (8000ns max), Cache Line Size: 0x04 (16 bytes)
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at f7fff800 (32-bit, non-prefetchable) [size=2K]
> Region 1: I/O ports at ec00 [size=128]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:02:04.0 RAID bus controller: VIA Technologies, Inc. VT6410 ATA133 RAID
>controller (rev 06)
> Subsystem: Asustek Computer, Inc.: Unknown device 80f4
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 64
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at e880 [size=8]
> Region 1: I/O ports at e800 [size=4]
> Region 2: I/O ports at e480 [size=8]
> Region 3: I/O ports at e400 [size=4]
> Region 4: I/O ports at e080 [size=16]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:02:05.0 Ethernet controller: 3Com Corporation 3c940 10/100/1000Base-T
>[Marvell] (rev 12)
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 0x04 (16 bytes)
> Interrupt: pin A routed to IRQ 22
> Region 0: Memory at f7ff4000 (32-bit, non-prefetchable) [size=16K]
> Region 1: I/O ports at d800 [size=256]
> Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [50] Vital Product Data
>
>0000:02:09.0 RAID bus controller: Silicon Image, Inc. (formerly CMD Technology
>Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02)
> Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) Winic W-680
>(Silicon Image 680 based)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size: 0x01 (4 bytes)
> Interrupt: pin A routed to IRQ 21
> Region 0: I/O ports at e000 [size=8]
> Region 1: I/O ports at dc00 [size=4]
> Region 2: I/O ports at d480 [size=8]
> Region 3: I/O ports at d400 [size=4]
> Region 4: I/O ports at d080 [size=16]
> Region 5: Memory at f7fff400 (32-bit, non-prefetchable) [size=256]
> Expansion ROM at f7f00000 [disabled] [size=512K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
>0000:02:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video
>Capture (rev 11)
> Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 64 (4000ns min, 10000ns max)
> Interrupt: pin A routed to IRQ 22
> Region 0: Memory at f3ffe000 (32-bit, prefetchable) [size=4K]
> Capabilities: [44] Vital Product Data
> Capabilities: [4c] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:02:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
>(rev 11)
> Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver, audio
>section)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 64 (1000ns min, 63750ns max)
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at f3fff000 (32-bit, prefetchable) [size=4K]
> Capabilities: [44] Vital Product Data
> Capabilities: [4c] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:02:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev
>08)
> Subsystem: Creative Labs CT4850 SBLive! Value
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 64 (500ns min, 5000ns max)
> Interrupt: pin A routed to IRQ 23
> Region 0: I/O ports at cc00 [size=32]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:02:0b.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev
>08)
> Subsystem: Creative Labs Gameport Joystick
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 64
> Region 0: I/O ports at d000 [size=8]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev
>74)
> Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
>SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
><MAbort- >SERR- <PERR-
> Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 0x04 (16 bytes)
> Interrupt: pin A routed to IRQ 20
> Region 0: I/O ports at c880 [size=128]
> Region 1: Memory at f7fff000 (32-bit, non-prefetchable) [size=128]
> Expansion ROM at f7fc0000 [disabled] [size=128K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
>Thanks in advance for any pointers!
>
>Jeremy
>
>
>
--
Michael Krufky
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-06 10:11 OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12) Jeremy Laine
2005-07-06 14:44 ` Michael Krufky
@ 2005-07-06 14:59 ` Alexey Dobriyan
2005-07-07 8:25 ` Jeremy Laine
1 sibling, 1 reply; 18+ messages in thread
From: Alexey Dobriyan @ 2005-07-06 14:59 UTC (permalink / raw)
To: Jeremy Laine; +Cc: linux-kernel
On Wednesday 06 July 2005 14:11, Jeremy Laine wrote:
> I keep getting OOPS's when using a Bt878 TV card, I am basically unable to watch
> TV for more than about 20-30mn without my system grinding to a halt.
> I have seen suggestions to try without PREEMPT enabled, which I will be doing
> shortly. Any other suggestions to get to the bottom of this problem are most
> welcome!
Try without loading all those proprietary modules (vmmon, vmnet, nvidia).
> Jul 6 10:55:44 sharky kernel: EIP: 0060:[__link_path_walk+1862/3520]
> Tainted: P VLI
^ permalink raw reply [flat|nested] 18+ messages in thread
* RE: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
@ 2005-07-06 15:02 Piszcz, Justin
2005-07-06 20:46 ` Lee Revell
0 siblings, 1 reply; 18+ messages in thread
From: Piszcz, Justin @ 2005-07-06 15:02 UTC (permalink / raw)
To: Jeremy Laine, linux-kernel
You probably aren't going to get any help with this until you reproduce
the problem without the vm* binary-only drivers.
Justin.
-----Original Message-----
From: linux-kernel-owner@vger.kernel.org
[mailto:linux-kernel-owner@vger.kernel.org] On Behalf Of Jeremy Laine
Sent: Wednesday, July 06, 2005 6:11 AM
To: linux-kernel@vger.kernel.org
Subject: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
Hi!
I keep getting OOPS's when using a Bt878 TV card, I am basically unable
to watch
TV for more than about 20-30mn without my system grinding to a halt. If
I do not
make use of the bttv module, the system is perfectly stable. I saw the
bttv
module is marked as "Orphan" in the MAINTAINERS file which is why I am
writing
straight to the LKML, do not hesitate to correct me if this is wrong!
I have seen suggestions to try without PREEMPT enabled, which I will be
doing
shortly. Any other suggestions to get to the bottom of this problem are
most
welcome!
The OOPS on 2.6.12 goes like so:
Jul 6 10:43:58 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
(44-958)
Jul 6 10:45:15 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
(44-958)
Jul 6 10:55:44 sharky kernel: Unable to handle kernel paging request at
virtual
address 0386c028
Jul 6 10:55:44 sharky kernel: printing eip:
Jul 6 10:55:44 sharky kernel: c0162ac6
Jul 6 10:55:44 sharky kernel: *pde = 00000000
Jul 6 10:55:44 sharky kernel: Oops: 0000 [#1]
Jul 6 10:55:44 sharky kernel: PREEMPT
Jul 6 10:55:44 sharky kernel: Modules linked in: nls_iso8859_1
nls_cp437 vfat
fat usb_storage vmnet vmmon lp ipt_TOS iptable_mangle ipt_MASQUERADE
ipt_multiport ipt_REJECT ipt_LOG ipt_limit ipt_state iptable_filter
parport_pc
parport intel_agp 3c59x mii snd_bt87x tuner tda9887 msp3400 bttv
video_buf
firmware_class btcx_risc tveeprom sk98lin tun snd_pcm_oss snd_mixer_oss
snd_intel8x0 snd_emu10k1 snd_rawmidi snd_seq_device snd_ac97_codec
snd_pcm
snd_timer snd_page_alloc snd_util_mem snd_hwdep snd soundcore ip_nat_ftp
iptable_nat ip_tables ip_conntrack_ftp ip_conntrack nvidia usblp
Jul 6 10:55:44 sharky kernel: CPU: 0
Jul 6 10:55:44 sharky kernel: EIP: 0060:[__link_path_walk+1862/3520]
Tainted: P VLI
Jul 6 10:55:44 sharky kernel: EFLAGS: 00010206 (2.6.12)
Jul 6 10:55:44 sharky kernel: EIP is at __link_path_walk+0x746/0xdc0
Jul 6 10:55:44 sharky kernel: eax: 0386c000 ebx: d5c3f003 ecx:
00000000
edx: c79e46b4
Jul 6 10:55:44 sharky kernel: esi: 00000000 edi: ceac50b8 ebp:
c7b85f10
esp: c7b85e1c
Jul 6 10:55:44 sharky kernel: ds: 007b es: 007b ss: 0068
Jul 6 10:55:44 sharky kernel: Process sylpheed-claws (pid: 12722,
threadinfo=c7b84000 task=cd51f020)
Jul 6 10:55:44 sharky kernel: Stack: c7b85f10 c7b85e4c c7b85e44
f6696700
00000000 c0156aab f6696700 0031f129
Jul 6 10:55:44 sharky kernel: 00001000 00000001 c17e0c80
c79e46b4
0011a425 00000003 d5c3f000 df56d0dc
Jul 6 10:55:44 sharky kernel: c7b85f10 c7b85f50 c7b85eb8
c7b85e78
c0163187 df56d0dc d5c3f000 df56d0dc
Jul 6 10:55:44 sharky kernel: Call Trace:
Jul 6 10:55:44 sharky kernel: [__getblk+43/96] __getblk+0x2b/0x60
Jul 6 10:55:44 sharky kernel: [link_path_walk+71/224]
link_path_walk+0x47/0xe0
Jul 6 10:55:44 sharky kernel: [path_lookup+127/320]
path_lookup+0x7f/0x140
Jul 6 10:55:44 sharky kernel: [__user_walk+51/96]
__user_walk+0x33/0x60
Jul 6 10:55:44 sharky kernel: [vfs_stat+31/96] vfs_stat+0x1f/0x60
Jul 6 10:55:44 sharky kernel: [sys_stat64+27/64] sys_stat64+0x1b/0x40
Jul 6 10:55:44 sharky kernel: [schedule+228/1568] schedule+0xe4/0x620
Jul 6 10:55:44 sharky kernel: [do_gettimeofday+26/208]
do_gettimeofday+0x1a/0xd0
Jul 6 10:55:44 sharky kernel: [sys_time+23/64] sys_time+0x17/0x40
Jul 6 10:55:44 sharky kernel: [syscall_call+7/11] syscall_call+0x7/0xb
Jul 6 10:55:44 sharky kernel: Code: fb ff ff f6 44 24 24 01 8b 54 24 2c
8b 7a
08 0f 84 44 03 00 00 85 ff 0f 84 3c 03 00 00 8b 87 8c 00 00 00 85 c0 0f
84 2e
03 00 00 <8b> 70 28 85 f6 0f 84 23 03 00 00 bb 00 e0 ff ff 21 e3 8b 03
83
Below is some information about my environment:
---[ /proc/cpuinfo ]---
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Pentium(R) 4 CPU 2.80GHz
stepping : 9
cpu MHz : 2807.248
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36
clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr
bogomips : 5537.79
---[ /proc/modules ]---
vmnet 32420 3 - Live 0xf8bd2000
vmmon 172076 0 - Live 0xf8bf0000
lp 11588 0 - Live 0xf8bc3000
ipt_TOS 2688 1 - Live 0xf8bc1000
iptable_mangle 2944 1 - Live 0xf8bb1000
ipt_MASQUERADE 3584 1 - Live 0xf8bba000
ipt_multiport 2688 4 - Live 0xf8b6f000
ipt_REJECT 5248 4 - Live 0xf8bb4000
ipt_LOG 7296 4 - Live 0xf8b9d000
ipt_limit 2560 4 - Live 0xf8b9b000
ipt_state 2048 13 - Live 0xf8b71000
iptable_filter 3200 1 - Live 0xf8b19000
parport_pc 36036 1 - Live 0xf8b51000
parport 25664 2 lp,parport_pc, Live 0xf8b67000
usblp 13312 0 - Live 0xf8b4c000
intel_agp 23580 1 - Live 0xf8aff000
3c59x 42152 0 - Live 0xf8b5b000
mii 5760 1 3c59x, Live 0xf8afc000
snd_bt87x 15048 0 - Live 0xf8b0f000
tuner 28712 0 - Live 0xf8b06000
tda9887 14360 0 - Live 0xf8ad5000
msp3400 27944 0 - Live 0xf8aed000
bttv 157968 0 - Live 0xf8b73000
video_buf 22404 1 bttv, Live 0xf8af5000
firmware_class 10496 1 bttv, Live 0xf8ada000
btcx_risc 5128 1 bttv, Live 0xf8abd000
tveeprom 13464 1 bttv, Live 0xf8998000
sk98lin 177248 0 - Live 0xf8b1f000
tun 11776 2 - Live 0xf89b5000
snd_pcm_oss 53536 0 - Live 0xf8ade000
snd_mixer_oss 19840 1 snd_pcm_oss, Live 0xf8ab7000
snd_intel8x0 33984 0 - Live 0xf8ac3000
snd_emu10k1 118788 0 - Live 0xf8a33000
snd_rawmidi 25888 1 snd_emu10k1, Live 0xf89c6000
snd_seq_device 8844 2 snd_emu10k1,snd_rawmidi, Live 0xf89a1000
snd_ac97_codec 83320 2 snd_intel8x0,snd_emu10k1, Live 0xf89fb000
snd_pcm 95240 5
snd_bt87x,snd_pcm_oss,snd_intel8x0,snd_emu10k1,snd_ac97_codec,
Live 0xf89e2000
snd_timer 25860 2 snd_emu10k1,snd_pcm, Live 0xf89be000
snd_page_alloc 10244 4 snd_bt87x,snd_intel8x0,snd_emu10k1,snd_pcm, Live
0xf899d000
snd_util_mem 4736 1 snd_emu10k1, Live 0xf898b000
snd_hwdep 9504 1 snd_emu10k1, Live 0xf8994000
snd 54756 11
snd_bt87x,snd_pcm_oss,snd_mixer_oss,snd_intel8x0,snd_emu10k1,snd_rawmidi
,snd_seq_device,snd_ac97_codec,snd_pcm,snd_timer,snd_hwdep,
Live 0xf89a6000
soundcore 10464 1 snd, Live 0xf8990000
ip_nat_ftp 3712 0 - Live 0xf8949000
iptable_nat 24028 3 ipt_MASQUERADE,ip_nat_ftp, Live 0xf8973000
ip_tables 22400 10
ipt_TOS,iptable_mangle,ipt_MASQUERADE,ipt_multiport,ipt_REJECT,ipt_LOG,i
pt_limit,ipt_state,iptable_filter,iptable_nat,
Live 0xf894c000
ip_conntrack_ftp 73104 1 ip_nat_ftp, Live 0xf8960000
ip_conntrack 45752 5
ipt_MASQUERADE,ipt_state,ip_nat_ftp,iptable_nat,ip_conntrack_ftp, Live
0xf8953000
nvidia 3922812 12 - Live 0xf8d3b000
---[ /proc/ioports ]---
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0290-0297 : pnp 00:0a
02f8-02ff : serial
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial
0400-041f : 0000:00:1f.3
0400-040f : i801-smbus
0480-04bf : 0000:00:1f.0
0680-06ff : pnp 00:0a
0800-087f : 0000:00:1f.0
0800-0803 : PM1a_EVT_BLK
0804-0805 : PM1a_CNT_BLK
0808-080b : PM_TMR
0828-082f : GPE0_BLK
0cf8-0cff : PCI conf1
b000-b0ff : 0000:00:1f.5
b000-b0ff : Intel ICH5
b400-b43f : 0000:00:1f.5
b400-b43f : Intel ICH5
b480-b49f : 0000:00:1d.0
b480-b49f : uhci_hcd
b800-b81f : 0000:00:1d.1
b800-b81f : uhci_hcd
b880-b89f : 0000:00:1d.2
b880-b89f : uhci_hcd
bc00-bc1f : 0000:00:1d.3
bc00-bc1f : uhci_hcd
c880-c8ff : 0000:02:0c.0
c880-c8ff : 0000:02:0c.0
cc00-cc1f : 0000:02:0b.0
cc00-cc1f : EMU10K1
d000-d007 : 0000:02:0b.1
d000-d007 : emu10k1-gp
d080-d08f : 0000:02:09.0
d400-d403 : 0000:02:09.0
d480-d487 : 0000:02:09.0
d800-d8ff : 0000:02:05.0
d800-d8ff : SysKonnect SK-98xx
dc00-dc03 : 0000:02:09.0
e000-e007 : 0000:02:09.0
e080-e08f : 0000:02:04.0
e400-e403 : 0000:02:04.0
e480-e487 : 0000:02:04.0
e800-e803 : 0000:02:04.0
e880-e887 : 0000:02:04.0
ec00-ec7f : 0000:02:03.0
fc00-fc0f : 0000:00:1f.1
fc00-fc07 : ide0
fc08-fc0f : ide1
---[ /proc/iomem ]---
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000ce800-000d2bff : Adapter ROM
000d3000-000d37ff : Adapter ROM
000f0000-000fffff : System ROM
00100000-3ff2ffff : System RAM
00100000-0035a10c : Kernel code
0035a10d-0045ab7f : Kernel data
3ff30000-3ff3ffff : ACPI Tables
3ff40000-3ffeffff : ACPI Non-volatile Storage
3fff0000-3fffffff : reserved
40000000-400003ff : 0000:00:1f.1
e0000000-f3efffff : PCI Bus #01
e0000000-efffffff : 0000:01:00.0
f3ffe000-f3ffefff : 0000:02:0a.0
f3ffe000-f3ffefff : bttv0
f3fff000-f3ffffff : 0000:02:0a.1
f4fff400-f4fff4ff : 0000:00:1f.5
f4fff400-f4fff4ff : Intel ICH5
f4fff800-f4fff9ff : 0000:00:1f.5
f4fff800-f4fff9ff : Intel ICH5
f4fffc00-f4ffffff : 0000:00:1d.7
f4fffc00-f4ffffff : ehci_hcd
f5000000-f7efffff : PCI Bus #01
f5000000-f5ffffff : 0000:01:00.0
f6000000-f6ffffff : 0000:01:00.0
f6000000-f6ffffff : nvidia
f7ff4000-f7ff7fff : 0000:02:05.0
f7ff4000-f7ff7fff : SysKonnect SK-98xx
f7fff000-f7fff07f : 0000:02:0c.0
f7fff400-f7fff4ff : 0000:02:09.0
f7fff400-f7fff4ff : SiI680
f7fff800-f7ffffff : 0000:02:03.0
f8000000-fbffffff : 0000:00:00.0
ffb80000-ffffffff : reserved
---[ lspci -vvv ]---
0000:00:00.0 Host bridge: Intel Corp. 82865G/PE/P DRAM
Controller/Host-Hub
Interface (rev 02)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] #09 [2106]
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+
Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP+ GART64- 64bit- FW-
Rate=x8
0000:00:01.0 PCI bridge: Intel Corp. 82865G/PE/P PCI to AGP Controller
(rev 02)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f5000000-f7efffff
Prefetchable memory behind bridge: e0000000-f3efffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB
UHCI #1
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at b480 [size=32]
0000:00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB
UHCI #2
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at b800 [size=32]
0000:00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB
UHCI #3
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b880 [size=32]
0000:00:1d.3 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB
UHCI #4
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at bc00 [size=32]
0000:00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2
EHCI
Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at f4fffc00 (32-bit, non-prefetchable)
[size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [20a0]
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2) (prog-if
00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000c000-0000efff
Memory behind bridge: f7f00000-fbffffff
Prefetchable memory behind bridge: f3f00000-f3ffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
0000:00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Bridge
(rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) Ultra
ATA 100
Storage Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at 40000000 (32-bit, non-prefetchable)
[size=1K]
0000:00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller
(rev
02)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 0400 [size=32]
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801EB/ER
(ICH5/ICH5R)
AC'97 Audio Controller (rev 02)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at b000 [size=256]
Region 1: I/O ports at b400 [size=64]
Region 2: Memory at f4fff800 (32-bit, non-prefetchable)
[size=512]
Region 3: Memory at f4fff400 (32-bit, non-prefetchable)
[size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:00.0 VGA compatible controller: nVidia Corporation NV40
OS1RT00B30 (rev
a1) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 817b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6000000 (32-bit, non-prefetchable)
[size=16M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 2: Memory at f5000000 (32-bit, non-prefetchable)
[size=16M]
Expansion ROM at f7ee0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+
AGP3+ Rate=x4,x8
Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit-
FW- Rate=x8
0000:02:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 46) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 808a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size: 0x04 (16 bytes)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f7fff800 (32-bit, non-prefetchable)
[size=2K]
Region 1: I/O ports at ec00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:04.0 RAID bus controller: VIA Technologies, Inc. VT6410 ATA133
RAID
controller (rev 06)
Subsystem: Asustek Computer, Inc.: Unknown device 80f4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e880 [size=8]
Region 1: I/O ports at e800 [size=4]
Region 2: I/O ports at e480 [size=8]
Region 3: I/O ports at e400 [size=4]
Region 4: I/O ports at e080 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:05.0 Ethernet controller: 3Com Corporation 3c940
10/100/1000Base-T
[Marvell] (rev 12)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 0x04 (16
bytes)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f7ff4000 (32-bit, non-prefetchable)
[size=16K]
Region 1: I/O ports at d800 [size=256]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
0000:02:09.0 RAID bus controller: Silicon Image, Inc. (formerly CMD
Technology
Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc)
Winic W-680
(Silicon Image 680 based)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x01 (4 bytes)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at e000 [size=8]
Region 1: I/O ports at dc00 [size=4]
Region 2: I/O ports at d480 [size=8]
Region 3: I/O ports at d400 [size=4]
Region 4: I/O ports at d080 [size=16]
Region 5: Memory at f7fff400 (32-bit, non-prefetchable)
[size=256]
Expansion ROM at f7f00000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:02:0a.0 Multimedia video controller: Brooktree Corporation Bt878
Video
Capture (rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo
receiver)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f3ffe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio
Capture
(rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo
receiver, audio
section)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f3fff000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1
(rev
08)
Subsystem: Creative Labs CT4850 SBLive! Value
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at cc00 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0b.1 Input device controller: Creative Labs SB Live! MIDI/Game
Port (rev
08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Region 0: I/O ports at d000 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M
[Tornado] (rev
74)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC
Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 0x04 (16
bytes)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at c880 [size=128]
Region 1: Memory at f7fff000 (32-bit, non-prefetchable)
[size=128]
Expansion ROM at f7fc0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Thanks in advance for any pointers!
Jeremy
--
http://www.jerryweb.org/ : JerryWeb.org
http://sailcut.sourceforge.net/ : Sailcut CAD
http://mpf70.sourceforge.net/ : MPman MP-F70 support for Linux
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel"
in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 18+ messages in thread
* RE: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-06 15:02 Piszcz, Justin
@ 2005-07-06 20:46 ` Lee Revell
0 siblings, 0 replies; 18+ messages in thread
From: Lee Revell @ 2005-07-06 20:46 UTC (permalink / raw)
To: Piszcz, Justin; +Cc: Jeremy Laine, linux-kernel
On Wed, 2005-07-06 at 11:02 -0400, Piszcz, Justin wrote:
> You probably aren't going to get any help with this until you reproduce
> the problem without the vm* binary-only drivers.
>
Also without nvidia.
Lee
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
[not found] <4njei-1Ps-21@gated-at.bofh.it>
@ 2005-07-06 23:09 ` Bodo Eggert
2005-07-07 8:17 ` Duncan Sands
2005-07-07 8:31 ` Jeremy Laine
0 siblings, 2 replies; 18+ messages in thread
From: Bodo Eggert @ 2005-07-06 23:09 UTC (permalink / raw)
To: Jeremy Laine, linux-kernel
Jeremy Laine <jeremy.laine@polytechnique.org> wrote:
> I keep getting OOPS's when using a Bt878 TV card, I am basically unable to
> watch TV for more than about 20-30mn without my system grinding to a halt. If
> I do not make use of the bttv module, the system is perfectly stable. I saw
> the bttv module is marked as "Orphan" in the MAINTAINERS file which is why I
> am writing straight to the LKML, do not hesitate to correct me if this is
> wrong!
>
> I have seen suggestions to try without PREEMPT enabled, which I will be doing
> shortly. Any other suggestions to get to the bottom of this problem are most
> welcome!
I've seen similar hehaviour (machine halts) with a BT848 on a VT82C686
board while displaying the picture on a radeon card under X.org 6.8.1.
Heavy HDD IO almost certainly caused soon death (recognizable by heavy
picture distortion), while an idle system lasted one evening. It did not
happen with kernel 2.4 and a NVidia card on XF86.
These errors were caused by memory corruption, the first four bytes of some
pages were overwritten with binary data (which affected some files in the
cache).
Now I've upgraded to X.org 6.8.2 and done a first stress-test (copying
large files from network to local HDD), and I still can post.
--
Ich danke GMX dafür, die Verwendung meiner Adressen mittels per SPF
verbreiteten Lügen zu sabotieren.
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-06 23:09 ` Bodo Eggert
@ 2005-07-07 8:17 ` Duncan Sands
2005-07-07 8:31 ` Jeremy Laine
1 sibling, 0 replies; 18+ messages in thread
From: Duncan Sands @ 2005-07-07 8:17 UTC (permalink / raw)
To: 7eggert; +Cc: Jeremy Laine, linux-kernel
> I've seen similar hehaviour (machine halts) with a BT848 on a VT82C686
> board while displaying the picture on a radeon card under X.org 6.8.1.
I have the same problem with a Bt878 on a VT82C686 board with a Radeon 7500
card. The problem predates X.org.
> Heavy HDD IO almost certainly caused soon death (recognizable by heavy
> picture distortion), while an idle system lasted one evening. It did not
> happen with kernel 2.4 and a NVidia card on XF86.
I get hard hangs.
> Now I've upgraded to X.org 6.8.2 and done a first stress-test (copying
> large files from network to local HDD), and I still can post.
Thanks for the hint - I will try updating X.org too.
All the best,
Duncan.
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-06 14:59 ` Alexey Dobriyan
@ 2005-07-07 8:25 ` Jeremy Laine
2005-07-07 15:12 ` Mauro Carvalho Chehab
0 siblings, 1 reply; 18+ messages in thread
From: Jeremy Laine @ 2005-07-07 8:25 UTC (permalink / raw)
To: linux-kernel; +Cc: video4linux-list
> Try without loading all those proprietary modules (vmmon, vmnet, nvidia).
Done, sorry about not doing it from the onset. I reproduced the OOPS using the
"vesa" driver of XFree86. Below is the OOPS as well as environment information:
Jul 6 22:57:29 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
(44-958)
Jul 6 22:58:45 sharky kernel: bttv0: OCERR @ 36311000,bits: HSYNC OFLOW OCERR*
Jul 6 22:58:45 sharky last message repeated 11 times
Jul 6 22:58:45 sharky kernel: bttv0: timeout: drop=67 irq=7604/49951,
risc=3631101c, bits: HSYNC OFLOW
Jul 6 22:58:45 sharky kernel: bttv0: reset, reinitialize
Jul 6 22:58:45 sharky kernel: bttv0: PLL: 28636363 => 35468950 . ok
Jul 6 23:06:08 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
(44-958)
Jul 6 23:12:57 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
(44-958)
Jul 6 23:14:12 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
(44-958)
Jul 7 02:11:36 sharky kernel: Unable to handle kernel paging request at virtual
address 1400000c
Jul 7 02:11:36 sharky kernel: printing eip:
Jul 7 02:11:36 sharky kernel: c013e362
Jul 7 02:11:36 sharky kernel: *pde = 00000000
Jul 7 02:11:36 sharky kernel: Oops: 0002 [#1]
Jul 7 02:11:36 sharky kernel: PREEMPT
Jul 7 02:11:36 sharky kernel: Modules linked in: lp ipt_TOS iptable_mangle
ipt_MASQUERADE ipt_multiport ipt_REJECT ipt_LOG ipt_limit ipt_state
iptable_filter parport_pc parport intel_agp 3c59x mii snd_bt87x tuner tda9887
msp3400 bttv video_buf firmware_class btcx_risc tveeprom sk98lin tun
snd_pcm_oss snd_mixer_oss snd_intel8x0 snd_emu10k1 snd_rawmidi snd_seq_device
snd_ac97_codec snd_pcm snd_timer snd_page_alloc snd_util_mem snd_hwdep snd
soundcore ip_nat_ftp iptable_nat ip_tables ip_conntrack_ftp ip_conntrack usblp
Jul 7 02:11:36 sharky kernel: CPU: 0
Jul 7 02:11:36 sharky kernel: EIP: 0060:[free_block+82/224] Tainted: P
VLI
Jul 7 02:11:36 sharky kernel: EFLAGS: 00010006 (2.6.12)
Jul 7 02:11:36 sharky kernel: EIP is at free_block+0x52/0xe0
Jul 7 02:11:36 sharky kernel: eax: 14000008 ebx: e19d8000 ecx: e19d8598
edx: 18929000
Jul 7 02:11:36 sharky kernel: esi: c17d7900 edi: 0000000f ebp: 0000001b
esp: f7ea3d08
Jul 7 02:11:36 sharky kernel: ds: 007b es: 007b ss: 0068
Jul 7 02:11:36 sharky kernel: Process kswapd0 (pid: 154, threadinfo=f7ea2000
task=f7e5a590)
Jul 7 02:11:36 sharky kernel: Stack: c01f22a0 c17db990 c17d791c c17db990
00000092 c0dde598 c17de8a0 c013e43c
Jul 7 02:11:36 sharky kernel: c17d7900 c17db990 0000001b 0000001b
c17db980 00000092 c0dde598 00000002
Jul 7 02:11:36 sharky kernel: c013e607 c17d7900 c17db980 00000000
c0dde598 f7ea3d78 c01effd6 c17d7900
Jul 7 02:11:36 sharky kernel: Call Trace:
Jul 7 02:11:36 sharky kernel: [memmove+80/84] memmove+0x50/0x54
Jul 7 02:11:36 sharky kernel: [cache_flusharray+76/208]
cache_flusharray+0x4c/0xd0
Jul 7 02:11:36 sharky kernel: [kmem_cache_free+71/80]
kmem_cache_free+0x47/0x50
Jul 7 02:11:36 sharky kernel: [radix_tree_delete+278/416]
radix_tree_delete+0x116/0x1a0
Jul 7 02:11:36 sharky kernel: [__pagevec_free+28/48] __pagevec_free+0x1c/0x30
Jul 7 02:11:36 sharky kernel: [__pagevec_release_nonlru+105/144]
__pagevec_release_nonlru+0x69/0x90
Jul 7 02:11:36 sharky kernel: [__remove_from_page_cache+36/80]
__remove_from_page_cache+0x24/0x50
Jul 7 02:11:36 sharky kernel: [shrink_list+755/1104] shrink_list+0x2f3/0x450
Jul 7 02:11:36 sharky kernel: [shrink_cache+272/736] shrink_cache+0x110/0x2e0
Jul 7 02:11:36 sharky kernel: [get_writeback_state+67/80]
get_writeback_state+0x43/0x50
Jul 7 02:11:36 sharky kernel: [shrink_slab+136/400] shrink_slab+0x88/0x190
Jul 7 02:11:36 sharky kernel: [shrink_zone+173/224] shrink_zone+0xad/0xe0
Jul 7 02:11:36 sharky kernel: [balance_pgdat+732/976]
balance_pgdat+0x2dc/0x3d0
Jul 7 02:11:36 sharky kernel: [kswapd+233/272] kswapd+0xe9/0x110
Jul 7 02:11:36 sharky kernel: [autoremove_wake_function+0/96]
autoremove_wake_function+0x0/0x60
Jul 7 02:11:36 sharky kernel: [ret_from_fork+6/20] ret_from_fork+0x6/0x14
Jul 7 02:11:36 sharky kernel: [autoremove_wake_function+0/96]
autoremove_wake_function+0x0/0x60
Jul 7 02:11:36 sharky kernel: [kswapd+0/272] kswapd+0x0/0x110
Jul 7 02:11:36 sharky kernel: [kernel_thread_helper+5/24]
kernel_thread_helper+0x5/0x18
Jul 7 02:11:36 sharky kernel: Code: 00 00 8d bc 27 00 00 00 00 8b 44 24 24 8b
15 70 97 49 c0 8b 0c b8 8d 81 00 00 00 40 c1 e8 0c c1 e0 05 8b 5c 02 1c 8b 53
04 8b 03 <89> 50 04 89 02 8b 43 0c 31 d2 c7 03 00 01 10 00 c7 43 04 00 02
Jul 7 02:11:36 sharky kernel: <6>note: kswapd0[154] exited with preempt_count
2
---[ /proc/cpuinfo ]---
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Pentium(R) 4 CPU 2.80GHz
stepping : 9
cpu MHz : 2807.470
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36
clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr
bogomips : 5537.79
---[ /proc/modules ]---
lp 11588 0 - Live 0xf8b80000
ipt_TOS 2688 1 - Live 0xf8b7e000
iptable_mangle 2944 1 - Live 0xf8b5b000
ipt_MASQUERADE 3584 1 - Live 0xf8b77000
ipt_multiport 2688 4 - Live 0xf8b2d000
ipt_REJECT 5248 4 - Live 0xf8b74000
ipt_LOG 7296 4 - Live 0xf8b71000
ipt_limit 2560 4 - Live 0xf8b59000
ipt_state 2048 13 - Live 0xf8b2f000
iptable_filter 3200 1 - Live 0xf8ad7000
parport_pc 36036 1 - Live 0xf8b0f000
parport 25664 2 lp,parport_pc, Live 0xf8b25000
usblp 13312 0 - Live 0xf8b0a000
intel_agp 23580 1 - Live 0xf8abd000
3c59x 42152 0 - Live 0xf8b19000
mii 5760 1 3c59x, Live 0xf8aba000
snd_bt87x 15048 0 - Live 0xf8acd000
tuner 28712 0 - Live 0xf8ac4000
tda9887 14360 0 - Live 0xf8a8b000
msp3400 27944 0 - Live 0xf8aab000
bttv 157968 0 - Live 0xf8b31000
video_buf 22404 1 bttv, Live 0xf8ab3000
firmware_class 10496 1 bttv, Live 0xf8a95000
btcx_risc 5128 1 bttv, Live 0xf8a7b000
tveeprom 13464 1 bttv, Live 0xf8956000
sk98lin 177248 0 - Live 0xf8add000
tun 11776 2 - Live 0xf8973000
snd_pcm_oss 53536 0 - Live 0xf8a9c000
snd_mixer_oss 19840 1 snd_pcm_oss, Live 0xf8a75000
snd_intel8x0 33984 0 - Live 0xf8a81000
snd_emu10k1 118788 0 - Live 0xf89f1000
snd_rawmidi 25888 1 snd_emu10k1, Live 0xf8984000
snd_seq_device 8844 2 snd_emu10k1,snd_rawmidi, Live 0xf895f000
snd_ac97_codec 83320 2 snd_intel8x0,snd_emu10k1, Live 0xf89b9000
snd_pcm 95240 5 snd_bt87x,snd_pcm_oss,snd_intel8x0,snd_emu10k1,snd_ac97_codec,
Live 0xf89a0000
snd_timer 25860 2 snd_emu10k1,snd_pcm, Live 0xf897c000
snd_page_alloc 10244 4 snd_bt87x,snd_intel8x0,snd_emu10k1,snd_pcm, Live
0xf895b000
snd_util_mem 4736 1 snd_emu10k1, Live 0xf8949000
snd_hwdep 9504 1 snd_emu10k1, Live 0xf8952000
snd 54756 11
snd_bt87x,snd_pcm_oss,snd_mixer_oss,snd_intel8x0,snd_emu10k1,snd_rawmidi,snd_seq_device,snd_ac97_codec,snd_pcm,snd_timer,snd_hwdep,
Live 0xf8964000
soundcore 10464 1 snd, Live 0xf894e000
ip_nat_ftp 3712 0 - Live 0xf8907000
iptable_nat 24028 3 ipt_MASQUERADE,ip_nat_ftp, Live 0xf8931000
ip_tables 22400 10
ipt_TOS,iptable_mangle,ipt_MASQUERADE,ipt_multiport,ipt_REJECT,ipt_LOG,ipt_limit,ipt_state,iptable_filter,iptable_nat,
Live 0xf890a000
ip_conntrack_ftp 73104 1 ip_nat_ftp, Live 0xf891e000
ip_conntrack 45752 5
ipt_MASQUERADE,ipt_state,ip_nat_ftp,iptable_nat,ip_conntrack_ftp, Live
0xf8911000
---[ /proc/ioports ]---
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0290-0297 : pnp 00:0a
02f8-02ff : serial
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial
0400-041f : 0000:00:1f.3
0400-040f : i801-smbus
0480-04bf : 0000:00:1f.0
0680-06ff : pnp 00:0a
0800-087f : 0000:00:1f.0
0800-0803 : PM1a_EVT_BLK
0804-0805 : PM1a_CNT_BLK
0808-080b : PM_TMR
0828-082f : GPE0_BLK
0cf8-0cff : PCI conf1
b000-b0ff : 0000:00:1f.5
b000-b0ff : Intel ICH5
b400-b43f : 0000:00:1f.5
b400-b43f : Intel ICH5
b480-b49f : 0000:00:1d.0
b480-b49f : uhci_hcd
b800-b81f : 0000:00:1d.1
b800-b81f : uhci_hcd
b880-b89f : 0000:00:1d.2
b880-b89f : uhci_hcd
bc00-bc1f : 0000:00:1d.3
bc00-bc1f : uhci_hcd
c880-c8ff : 0000:02:0c.0
c880-c8ff : 0000:02:0c.0
cc00-cc1f : 0000:02:0b.0
cc00-cc1f : EMU10K1
d000-d007 : 0000:02:0b.1
d000-d007 : emu10k1-gp
d080-d08f : 0000:02:09.0
d400-d403 : 0000:02:09.0
d480-d487 : 0000:02:09.0
d800-d8ff : 0000:02:05.0
d800-d8ff : SysKonnect SK-98xx
dc00-dc03 : 0000:02:09.0
e000-e007 : 0000:02:09.0
e080-e08f : 0000:02:04.0
e400-e403 : 0000:02:04.0
e480-e487 : 0000:02:04.0
e800-e803 : 0000:02:04.0
e880-e887 : 0000:02:04.0
ec00-ec7f : 0000:02:03.0
fc00-fc0f : 0000:00:1f.1
fc00-fc07 : ide0
fc08-fc0f : ide1
---[ /proc/iomem ]---
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000ce800-000d2bff : Adapter ROM
000d3000-000d37ff : Adapter ROM
000f0000-000fffff : System ROM
00100000-3ff2ffff : System RAM
00100000-0035a10c : Kernel code
0035a10d-0045ab7f : Kernel data
3ff30000-3ff3ffff : ACPI Tables
3ff40000-3ffeffff : ACPI Non-volatile Storage
3fff0000-3fffffff : reserved
40000000-400003ff : 0000:00:1f.1
e0000000-f3efffff : PCI Bus #01
e0000000-efffffff : 0000:01:00.0
f3ffe000-f3ffefff : 0000:02:0a.0
f3ffe000-f3ffefff : bttv0
f3fff000-f3ffffff : 0000:02:0a.1
f4fff400-f4fff4ff : 0000:00:1f.5
f4fff400-f4fff4ff : Intel ICH5
f4fff800-f4fff9ff : 0000:00:1f.5
f4fff800-f4fff9ff : Intel ICH5
f4fffc00-f4ffffff : 0000:00:1d.7
f4fffc00-f4ffffff : ehci_hcd
f5000000-f7efffff : PCI Bus #01
f5000000-f5ffffff : 0000:01:00.0
f6000000-f6ffffff : 0000:01:00.0
f7ff4000-f7ff7fff : 0000:02:05.0
f7ff4000-f7ff7fff : SysKonnect SK-98xx
f7fff000-f7fff07f : 0000:02:0c.0
f7fff400-f7fff4ff : 0000:02:09.0
f7fff400-f7fff4ff : SiI680
f7fff800-f7ffffff : 0000:02:03.0
f8000000-fbffffff : 0000:00:00.0
ffb80000-ffffffff : reserved
---[ lspci -vvv ]---
0000:00:00.0 Host bridge: Intel Corp. 82865G/PE/P DRAM Controller/Host-Hub
Interface (rev 02)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] #09 [2106]
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+
Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
0000:00:01.0 PCI bridge: Intel Corp. 82865G/PE/P PCI to AGP Controller (rev 02)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f5000000-f7efffff
Prefetchable memory behind bridge: e0000000-f3efffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at b480 [size=32]
0000:00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at b800 [size=32]
0000:00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b880 [size=32]
0000:00:1d.3 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at bc00 [size=32]
0000:00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI
Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at f4fffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [20a0]
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000c000-0000efff
Memory behind bridge: f7f00000-fbffffff
Prefetchable memory behind bridge: f3f00000-f3ffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
0000:00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Bridge (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) Ultra ATA 100
Storage Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
0000:00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev
02)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 0400 [size=32]
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801EB/ER (ICH5/ICH5R)
AC'97 Audio Controller (rev 02)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at b000 [size=256]
Region 1: I/O ports at b400 [size=64]
Region 2: Memory at f4fff800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at f4fff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:00.0 VGA compatible controller: nVidia Corporation NV40 OS1RT00B30 (rev
a1) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 817b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 2: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at f7ee0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+
AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
0000:02:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 46) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 808a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size: 0x04 (16 bytes)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f7fff800 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at ec00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:04.0 RAID bus controller: VIA Technologies, Inc. VT6410 ATA133 RAID
controller (rev 06)
Subsystem: Asustek Computer, Inc.: Unknown device 80f4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e880 [size=8]
Region 1: I/O ports at e800 [size=4]
Region 2: I/O ports at e480 [size=8]
Region 3: I/O ports at e400 [size=4]
Region 4: I/O ports at e080 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:05.0 Ethernet controller: 3Com Corporation 3c940 10/100/1000Base-T
[Marvell] (rev 12)
Subsystem: Asustek Computer, Inc. P4P800 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 0x04 (16 bytes)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f7ff4000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at d800 [size=256]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
0000:02:09.0 RAID bus controller: Silicon Image, Inc. (formerly CMD Technology
Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) Winic W-680
(Silicon Image 680 based)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x01 (4 bytes)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at e000 [size=8]
Region 1: I/O ports at dc00 [size=4]
Region 2: I/O ports at d480 [size=8]
Region 3: I/O ports at d400 [size=4]
Region 4: I/O ports at d080 [size=16]
Region 5: Memory at f7fff400 (32-bit, non-prefetchable) [size=256]
Expansion ROM at f7f00000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:02:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f3ffe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver, audio
section)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f3fff000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev
08)
Subsystem: Creative Labs CT4850 SBLive! Value
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at cc00 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0b.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev
08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Region 0: I/O ports at d000 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev
74)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 0x04 (16 bytes)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at c880 [size=128]
Region 1: Memory at f7fff000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at f7fc0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Jeremy
--
http://www.jerryweb.org/ : JerryWeb.org
http://sailcut.sourceforge.net/ : Sailcut CAD
http://mpf70.sourceforge.net/ : MPman MP-F70 support for Linux
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-06 23:09 ` Bodo Eggert
2005-07-07 8:17 ` Duncan Sands
@ 2005-07-07 8:31 ` Jeremy Laine
1 sibling, 0 replies; 18+ messages in thread
From: Jeremy Laine @ 2005-07-07 8:31 UTC (permalink / raw)
To: 7eggert; +Cc: linux-kernel
> Heavy HDD IO almost certainly caused soon death (recognizable by heavy
> picture distortion), while an idle system lasted one evening. It did not
> happen with kernel 2.4 and a NVidia card on XF86.
You are very probably onto something there, the latest OOPS I sent (the 2AM one)
occurred while my daily backup script was running!
Jul 7 02:10:01 sharky /USR/SBIN/CRON[6656]: (root) CMD
(/home/save/bin/mount-wrapper bkp-section -c daily)
Jul 7 02:10:08 sharky kernel: EXT3 FS on dm-2, internal journal
Jul 7 02:11:36 sharky kernel: Unable to handle kernel paging request at virtual
address 1400000c
Kind regards,
Jeremy
--
http://www.jerryweb.org/ : JerryWeb.org
http://sailcut.sourceforge.net/ : Sailcut CAD
http://opensource.polytechnique.org/ : Polytechnique.org Free Software
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-06 14:44 ` Michael Krufky
@ 2005-07-07 14:31 ` Lee Revell
2005-07-07 14:35 ` Michael Krufky
0 siblings, 1 reply; 18+ messages in thread
From: Lee Revell @ 2005-07-07 14:31 UTC (permalink / raw)
To: mkrufky
Cc: Jeremy Laine, linux-kernel, Mauro Carvalho Chehab,
Linux and Kernel Video
On Wed, 2005-07-06 at 10:44 -0400, Michael Krufky wrote:
> bttv is now maintained by Mauro Carvalho Chehab
> <mchehab@brturbo.com.br>, as part of the video4linux project. I am
> forwarding this to Mauro and the video4linux list. Linux and Kernel
> Video <video4linux-list@redhat.com>
Where's the MAINTAINERS patch?
Lee
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-07 14:31 ` Lee Revell
@ 2005-07-07 14:35 ` Michael Krufky
0 siblings, 0 replies; 18+ messages in thread
From: Michael Krufky @ 2005-07-07 14:35 UTC (permalink / raw)
To: Lee Revell; +Cc: linux-kernel, Mauro Carvalho Chehab, Linux and Kernel Video
Lee Revell wrote:
>On Wed, 2005-07-06 at 10:44 -0400, Michael Krufky wrote:
>
>
>>bttv is now maintained by Mauro Carvalho Chehab
>><mchehab@brturbo.com.br>, as part of the video4linux project. I am
>>forwarding this to Mauro and the video4linux list. Linux and Kernel
>>Video <video4linux-list@redhat.com>
>>
>>
>
>Where's the MAINTAINERS patch?
>
>Lee
>
>
>
It has been in Linus' tree since 2.6.13-rc1
--
Michael Krufky
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-07 8:25 ` Jeremy Laine
@ 2005-07-07 15:12 ` Mauro Carvalho Chehab
2005-07-07 15:35 ` Jeremy Laine
2005-07-07 16:17 ` matthieu castet
0 siblings, 2 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2005-07-07 15:12 UTC (permalink / raw)
To: Jeremy Laine; +Cc: linux-kernel, video4linux-list
Jeremy,
BTTV cards uses massive data transfer via DMA when you are watching TV,
transfering one screen every 1/30 s. Maybe you are suffering from a
trouble on your motherboard or at board physical connection.
We don't have any other OOPS reported for BTTV cards. I believe it is
something on your hardware or software configuration that is generating
the OOPS (not a kernel trouble).
From your lspci, you have lots of cards on it. Maybe you are
experiencing some kind of bad contact in one of them.
In order to troubleshooting, you can:
1) desactivate any overclocking at motherboard/video board;
2) use a standard vanilla kernel (not a distro kernel, that may have
some experimental patches applied;
3) use a minimum ammount of cards leaving only neccessary cards at MB.
For these, it is good to clean its contacts;
4) Test it again.
After doing it, please send us a report c/c video4linux list.
Mauro.
Jeremy Laine wrote:
>>Try without loading all those proprietary modules (vmmon, vmnet, nvidia).
>
>
> Done, sorry about not doing it from the onset. I reproduced the OOPS using the
> "vesa" driver of XFree86. Below is the OOPS as well as environment information:
>
> Jul 6 22:57:29 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
> (44-958)
> Jul 6 22:58:45 sharky kernel: bttv0: OCERR @ 36311000,bits: HSYNC OFLOW OCERR*
> Jul 6 22:58:45 sharky last message repeated 11 times
> Jul 6 22:58:45 sharky kernel: bttv0: timeout: drop=67 irq=7604/49951,
> risc=3631101c, bits: HSYNC OFLOW
> Jul 6 22:58:45 sharky kernel: bttv0: reset, reinitialize
> Jul 6 22:58:45 sharky kernel: bttv0: PLL: 28636363 => 35468950 . ok
> Jul 6 23:06:08 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
> (44-958)
> Jul 6 23:12:57 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
> (44-958)
> Jul 6 23:14:12 sharky kernel: tuner 2-0060: TV freq (0.00) out of range
> (44-958)
> Jul 7 02:11:36 sharky kernel: Unable to handle kernel paging request at virtual
> address 1400000c
> Jul 7 02:11:36 sharky kernel: printing eip:
> Jul 7 02:11:36 sharky kernel: c013e362
> Jul 7 02:11:36 sharky kernel: *pde = 00000000
> Jul 7 02:11:36 sharky kernel: Oops: 0002 [#1]
> Jul 7 02:11:36 sharky kernel: PREEMPT
> Jul 7 02:11:36 sharky kernel: Modules linked in: lp ipt_TOS iptable_mangle
> ipt_MASQUERADE ipt_multiport ipt_REJECT ipt_LOG ipt_limit ipt_state
> iptable_filter parport_pc parport intel_agp 3c59x mii snd_bt87x tuner tda9887
> msp3400 bttv video_buf firmware_class btcx_risc tveeprom sk98lin tun
> snd_pcm_oss snd_mixer_oss snd_intel8x0 snd_emu10k1 snd_rawmidi snd_seq_device
> snd_ac97_codec snd_pcm snd_timer snd_page_alloc snd_util_mem snd_hwdep snd
> soundcore ip_nat_ftp iptable_nat ip_tables ip_conntrack_ftp ip_conntrack usblp
> Jul 7 02:11:36 sharky kernel: CPU: 0
> Jul 7 02:11:36 sharky kernel: EIP: 0060:[free_block+82/224] Tainted: P
> VLI
> Jul 7 02:11:36 sharky kernel: EFLAGS: 00010006 (2.6.12)
> Jul 7 02:11:36 sharky kernel: EIP is at free_block+0x52/0xe0
> Jul 7 02:11:36 sharky kernel: eax: 14000008 ebx: e19d8000 ecx: e19d8598
> edx: 18929000
> Jul 7 02:11:36 sharky kernel: esi: c17d7900 edi: 0000000f ebp: 0000001b
> esp: f7ea3d08
> Jul 7 02:11:36 sharky kernel: ds: 007b es: 007b ss: 0068
> Jul 7 02:11:36 sharky kernel: Process kswapd0 (pid: 154, threadinfo=f7ea2000
> task=f7e5a590)
> Jul 7 02:11:36 sharky kernel: Stack: c01f22a0 c17db990 c17d791c c17db990
> 00000092 c0dde598 c17de8a0 c013e43c
> Jul 7 02:11:36 sharky kernel: c17d7900 c17db990 0000001b 0000001b
> c17db980 00000092 c0dde598 00000002
> Jul 7 02:11:36 sharky kernel: c013e607 c17d7900 c17db980 00000000
> c0dde598 f7ea3d78 c01effd6 c17d7900
> Jul 7 02:11:36 sharky kernel: Call Trace:
> Jul 7 02:11:36 sharky kernel: [memmove+80/84] memmove+0x50/0x54
> Jul 7 02:11:36 sharky kernel: [cache_flusharray+76/208]
> cache_flusharray+0x4c/0xd0
> Jul 7 02:11:36 sharky kernel: [kmem_cache_free+71/80]
> kmem_cache_free+0x47/0x50
> Jul 7 02:11:36 sharky kernel: [radix_tree_delete+278/416]
> radix_tree_delete+0x116/0x1a0
> Jul 7 02:11:36 sharky kernel: [__pagevec_free+28/48] __pagevec_free+0x1c/0x30
> Jul 7 02:11:36 sharky kernel: [__pagevec_release_nonlru+105/144]
> __pagevec_release_nonlru+0x69/0x90
> Jul 7 02:11:36 sharky kernel: [__remove_from_page_cache+36/80]
> __remove_from_page_cache+0x24/0x50
> Jul 7 02:11:36 sharky kernel: [shrink_list+755/1104] shrink_list+0x2f3/0x450
> Jul 7 02:11:36 sharky kernel: [shrink_cache+272/736] shrink_cache+0x110/0x2e0
> Jul 7 02:11:36 sharky kernel: [get_writeback_state+67/80]
> get_writeback_state+0x43/0x50
> Jul 7 02:11:36 sharky kernel: [shrink_slab+136/400] shrink_slab+0x88/0x190
> Jul 7 02:11:36 sharky kernel: [shrink_zone+173/224] shrink_zone+0xad/0xe0
> Jul 7 02:11:36 sharky kernel: [balance_pgdat+732/976]
> balance_pgdat+0x2dc/0x3d0
> Jul 7 02:11:36 sharky kernel: [kswapd+233/272] kswapd+0xe9/0x110
> Jul 7 02:11:36 sharky kernel: [autoremove_wake_function+0/96]
> autoremove_wake_function+0x0/0x60
> Jul 7 02:11:36 sharky kernel: [ret_from_fork+6/20] ret_from_fork+0x6/0x14
> Jul 7 02:11:36 sharky kernel: [autoremove_wake_function+0/96]
> autoremove_wake_function+0x0/0x60
> Jul 7 02:11:36 sharky kernel: [kswapd+0/272] kswapd+0x0/0x110
> Jul 7 02:11:36 sharky kernel: [kernel_thread_helper+5/24]
> kernel_thread_helper+0x5/0x18
> Jul 7 02:11:36 sharky kernel: Code: 00 00 8d bc 27 00 00 00 00 8b 44 24 24 8b
> 15 70 97 49 c0 8b 0c b8 8d 81 00 00 00 40 c1 e8 0c c1 e0 05 8b 5c 02 1c 8b 53
> 04 8b 03 <89> 50 04 89 02 8b 43 0c 31 d2 c7 03 00 01 10 00 c7 43 04 00 02
> Jul 7 02:11:36 sharky kernel: <6>note: kswapd0[154] exited with preempt_count
> 2
>
>
> ---[ /proc/cpuinfo ]---
>
> processor : 0
> vendor_id : GenuineIntel
> cpu family : 15
> model : 2
> model name : Intel(R) Pentium(R) 4 CPU 2.80GHz
> stepping : 9
> cpu MHz : 2807.470
> cache size : 512 KB
> fdiv_bug : no
> hlt_bug : no
> f00f_bug : no
> coma_bug : no
> fpu : yes
> fpu_exception : yes
> cpuid level : 2
> wp : yes
> flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36
> clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr
> bogomips : 5537.79
>
>
> ---[ /proc/modules ]---
>
> lp 11588 0 - Live 0xf8b80000
> ipt_TOS 2688 1 - Live 0xf8b7e000
> iptable_mangle 2944 1 - Live 0xf8b5b000
> ipt_MASQUERADE 3584 1 - Live 0xf8b77000
> ipt_multiport 2688 4 - Live 0xf8b2d000
> ipt_REJECT 5248 4 - Live 0xf8b74000
> ipt_LOG 7296 4 - Live 0xf8b71000
> ipt_limit 2560 4 - Live 0xf8b59000
> ipt_state 2048 13 - Live 0xf8b2f000
> iptable_filter 3200 1 - Live 0xf8ad7000
> parport_pc 36036 1 - Live 0xf8b0f000
> parport 25664 2 lp,parport_pc, Live 0xf8b25000
> usblp 13312 0 - Live 0xf8b0a000
> intel_agp 23580 1 - Live 0xf8abd000
> 3c59x 42152 0 - Live 0xf8b19000
> mii 5760 1 3c59x, Live 0xf8aba000
> snd_bt87x 15048 0 - Live 0xf8acd000
> tuner 28712 0 - Live 0xf8ac4000
> tda9887 14360 0 - Live 0xf8a8b000
> msp3400 27944 0 - Live 0xf8aab000
> bttv 157968 0 - Live 0xf8b31000
> video_buf 22404 1 bttv, Live 0xf8ab3000
> firmware_class 10496 1 bttv, Live 0xf8a95000
> btcx_risc 5128 1 bttv, Live 0xf8a7b000
> tveeprom 13464 1 bttv, Live 0xf8956000
> sk98lin 177248 0 - Live 0xf8add000
> tun 11776 2 - Live 0xf8973000
> snd_pcm_oss 53536 0 - Live 0xf8a9c000
> snd_mixer_oss 19840 1 snd_pcm_oss, Live 0xf8a75000
> snd_intel8x0 33984 0 - Live 0xf8a81000
> snd_emu10k1 118788 0 - Live 0xf89f1000
> snd_rawmidi 25888 1 snd_emu10k1, Live 0xf8984000
> snd_seq_device 8844 2 snd_emu10k1,snd_rawmidi, Live 0xf895f000
> snd_ac97_codec 83320 2 snd_intel8x0,snd_emu10k1, Live 0xf89b9000
> snd_pcm 95240 5 snd_bt87x,snd_pcm_oss,snd_intel8x0,snd_emu10k1,snd_ac97_codec,
> Live 0xf89a0000
> snd_timer 25860 2 snd_emu10k1,snd_pcm, Live 0xf897c000
> snd_page_alloc 10244 4 snd_bt87x,snd_intel8x0,snd_emu10k1,snd_pcm, Live
> 0xf895b000
> snd_util_mem 4736 1 snd_emu10k1, Live 0xf8949000
> snd_hwdep 9504 1 snd_emu10k1, Live 0xf8952000
> snd 54756 11
> snd_bt87x,snd_pcm_oss,snd_mixer_oss,snd_intel8x0,snd_emu10k1,snd_rawmidi,snd_seq_device,snd_ac97_codec,snd_pcm,snd_timer,snd_hwdep,
> Live 0xf8964000
> soundcore 10464 1 snd, Live 0xf894e000
> ip_nat_ftp 3712 0 - Live 0xf8907000
> iptable_nat 24028 3 ipt_MASQUERADE,ip_nat_ftp, Live 0xf8931000
> ip_tables 22400 10
> ipt_TOS,iptable_mangle,ipt_MASQUERADE,ipt_multiport,ipt_REJECT,ipt_LOG,ipt_limit,ipt_state,iptable_filter,iptable_nat,
> Live 0xf890a000
> ip_conntrack_ftp 73104 1 ip_nat_ftp, Live 0xf891e000
> ip_conntrack 45752 5
> ipt_MASQUERADE,ipt_state,ip_nat_ftp,iptable_nat,ip_conntrack_ftp, Live
> 0xf8911000
>
>
> ---[ /proc/ioports ]---
>
> 0000-001f : dma1
> 0020-0021 : pic1
> 0040-0043 : timer0
> 0050-0053 : timer1
> 0060-006f : keyboard
> 0070-0077 : rtc
> 0080-008f : dma page reg
> 00a0-00a1 : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 0170-0177 : ide1
> 01f0-01f7 : ide0
> 0290-0297 : pnp 00:0a
> 02f8-02ff : serial
> 0376-0376 : ide1
> 0378-037a : parport0
> 03c0-03df : vga+
> 03f6-03f6 : ide0
> 03f8-03ff : serial
> 0400-041f : 0000:00:1f.3
> 0400-040f : i801-smbus
> 0480-04bf : 0000:00:1f.0
> 0680-06ff : pnp 00:0a
> 0800-087f : 0000:00:1f.0
> 0800-0803 : PM1a_EVT_BLK
> 0804-0805 : PM1a_CNT_BLK
> 0808-080b : PM_TMR
> 0828-082f : GPE0_BLK
> 0cf8-0cff : PCI conf1
> b000-b0ff : 0000:00:1f.5
> b000-b0ff : Intel ICH5
> b400-b43f : 0000:00:1f.5
> b400-b43f : Intel ICH5
> b480-b49f : 0000:00:1d.0
> b480-b49f : uhci_hcd
> b800-b81f : 0000:00:1d.1
> b800-b81f : uhci_hcd
> b880-b89f : 0000:00:1d.2
> b880-b89f : uhci_hcd
> bc00-bc1f : 0000:00:1d.3
> bc00-bc1f : uhci_hcd
> c880-c8ff : 0000:02:0c.0
> c880-c8ff : 0000:02:0c.0
> cc00-cc1f : 0000:02:0b.0
> cc00-cc1f : EMU10K1
> d000-d007 : 0000:02:0b.1
> d000-d007 : emu10k1-gp
> d080-d08f : 0000:02:09.0
> d400-d403 : 0000:02:09.0
> d480-d487 : 0000:02:09.0
> d800-d8ff : 0000:02:05.0
> d800-d8ff : SysKonnect SK-98xx
> dc00-dc03 : 0000:02:09.0
> e000-e007 : 0000:02:09.0
> e080-e08f : 0000:02:04.0
> e400-e403 : 0000:02:04.0
> e480-e487 : 0000:02:04.0
> e800-e803 : 0000:02:04.0
> e880-e887 : 0000:02:04.0
> ec00-ec7f : 0000:02:03.0
> fc00-fc0f : 0000:00:1f.1
> fc00-fc07 : ide0
> fc08-fc0f : ide1
>
>
> ---[ /proc/iomem ]---
>
> 00000000-0009fbff : System RAM
> 0009fc00-0009ffff : reserved
> 000a0000-000bffff : Video RAM area
> 000c0000-000c7fff : Video ROM
> 000ce800-000d2bff : Adapter ROM
> 000d3000-000d37ff : Adapter ROM
> 000f0000-000fffff : System ROM
> 00100000-3ff2ffff : System RAM
> 00100000-0035a10c : Kernel code
> 0035a10d-0045ab7f : Kernel data
> 3ff30000-3ff3ffff : ACPI Tables
> 3ff40000-3ffeffff : ACPI Non-volatile Storage
> 3fff0000-3fffffff : reserved
> 40000000-400003ff : 0000:00:1f.1
> e0000000-f3efffff : PCI Bus #01
> e0000000-efffffff : 0000:01:00.0
> f3ffe000-f3ffefff : 0000:02:0a.0
> f3ffe000-f3ffefff : bttv0
> f3fff000-f3ffffff : 0000:02:0a.1
> f4fff400-f4fff4ff : 0000:00:1f.5
> f4fff400-f4fff4ff : Intel ICH5
> f4fff800-f4fff9ff : 0000:00:1f.5
> f4fff800-f4fff9ff : Intel ICH5
> f4fffc00-f4ffffff : 0000:00:1d.7
> f4fffc00-f4ffffff : ehci_hcd
> f5000000-f7efffff : PCI Bus #01
> f5000000-f5ffffff : 0000:01:00.0
> f6000000-f6ffffff : 0000:01:00.0
> f7ff4000-f7ff7fff : 0000:02:05.0
> f7ff4000-f7ff7fff : SysKonnect SK-98xx
> f7fff000-f7fff07f : 0000:02:0c.0
> f7fff400-f7fff4ff : 0000:02:09.0
> f7fff400-f7fff4ff : SiI680
> f7fff800-f7ffffff : 0000:02:03.0
> f8000000-fbffffff : 0000:00:00.0
> ffb80000-ffffffff : reserved
>
>
> ---[ lspci -vvv ]---
>
> 0000:00:00.0 Host bridge: Intel Corp. 82865G/PE/P DRAM Controller/Host-Hub
> Interface (rev 02)
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
> Capabilities: [e4] #09 [2106]
> Capabilities: [a0] AGP version 3.0
> Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+
> Rate=x4,x8
> Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
>
> 0000:00:01.0 PCI bridge: Intel Corp. 82865G/PE/P PCI to AGP Controller (rev 02)
> (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: f5000000-f7efffff
> Prefetchable memory behind bridge: e0000000-f3efffff
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
>
> 0000:00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1
> (rev 02) (prog-if 00 [UHCI])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> Region 4: I/O ports at b480 [size=32]
>
> 0000:00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2
> (rev 02) (prog-if 00 [UHCI])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 19
> Region 4: I/O ports at b800 [size=32]
>
> 0000:00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3
> (rev 02) (prog-if 00 [UHCI])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin C routed to IRQ 18
> Region 4: I/O ports at b880 [size=32]
>
> 0000:00:1d.3 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4
> (rev 02) (prog-if 00 [UHCI])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> Region 4: I/O ports at bc00 [size=32]
>
> 0000:00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI
> Controller (rev 02) (prog-if 20 [EHCI])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 23
> Region 0: Memory at f4fffc00 (32-bit, non-prefetchable) [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] #0a [20a0]
>
> 0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2) (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> I/O behind bridge: 0000c000-0000efff
> Memory behind bridge: f7f00000-fbffffff
> Prefetchable memory behind bridge: f3f00000-f3ffffff
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
>
> 0000:00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Bridge (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
>
> 0000:00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) Ultra ATA 100
> Storage Controller (rev 02) (prog-if 8a [Master SecP PriP])
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 18
> Region 0: I/O ports at <unassigned>
> Region 1: I/O ports at <unassigned>
> Region 2: I/O ports at <unassigned>
> Region 3: I/O ports at <unassigned>
> Region 4: I/O ports at fc00 [size=16]
> Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
>
> 0000:00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev
> 02)
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 5
> Region 4: I/O ports at 0400 [size=32]
>
> 0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801EB/ER (ICH5/ICH5R)
> AC'97 Audio Controller (rev 02)
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 17
> Region 0: I/O ports at b000 [size=256]
> Region 1: I/O ports at b400 [size=64]
> Region 2: Memory at f4fff800 (32-bit, non-prefetchable) [size=512]
> Region 3: Memory at f4fff400 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 0000:01:00.0 VGA compatible controller: nVidia Corporation NV40 OS1RT00B30 (rev
> a1) (prog-if 00 [VGA])
> Subsystem: Asustek Computer, Inc.: Unknown device 817b
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 10
> Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M]
> Region 2: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
> Expansion ROM at f7ee0000 [disabled] [size=128K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 3.0
> Status: RQ=256 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+
> AGP3+ Rate=x4,x8
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
>
> 0000:02:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
> Controller (rev 46) (prog-if 10 [OHCI])
> Subsystem: Asustek Computer, Inc.: Unknown device 808a
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (8000ns max), Cache Line Size: 0x04 (16 bytes)
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at f7fff800 (32-bit, non-prefetchable) [size=2K]
> Region 1: I/O ports at ec00 [size=128]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 0000:02:04.0 RAID bus controller: VIA Technologies, Inc. VT6410 ATA133 RAID
> controller (rev 06)
> Subsystem: Asustek Computer, Inc.: Unknown device 80f4
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at e880 [size=8]
> Region 1: I/O ports at e800 [size=4]
> Region 2: I/O ports at e480 [size=8]
> Region 3: I/O ports at e400 [size=4]
> Region 4: I/O ports at e080 [size=16]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 0000:02:05.0 Ethernet controller: 3Com Corporation 3c940 10/100/1000Base-T
> [Marvell] (rev 12)
> Subsystem: Asustek Computer, Inc. P4P800 Mainboard
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 0x04 (16 bytes)
> Interrupt: pin A routed to IRQ 22
> Region 0: Memory at f7ff4000 (32-bit, non-prefetchable) [size=16K]
> Region 1: I/O ports at d800 [size=256]
> Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [50] Vital Product Data
>
> 0000:02:09.0 RAID bus controller: Silicon Image, Inc. (formerly CMD Technology
> Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02)
> Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) Winic W-680
> (Silicon Image 680 based)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size: 0x01 (4 bytes)
> Interrupt: pin A routed to IRQ 21
> Region 0: I/O ports at e000 [size=8]
> Region 1: I/O ports at dc00 [size=4]
> Region 2: I/O ports at d480 [size=8]
> Region 3: I/O ports at d400 [size=4]
> Region 4: I/O ports at d080 [size=16]
> Region 5: Memory at f7fff400 (32-bit, non-prefetchable) [size=256]
> Expansion ROM at f7f00000 [disabled] [size=512K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
> 0000:02:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video
> Capture (rev 11)
> Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (4000ns min, 10000ns max)
> Interrupt: pin A routed to IRQ 22
> Region 0: Memory at f3ffe000 (32-bit, prefetchable) [size=4K]
> Capabilities: [44] Vital Product Data
> Capabilities: [4c] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 0000:02:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
> (rev 11)
> Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver, audio
> section)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (1000ns min, 63750ns max)
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at f3fff000 (32-bit, prefetchable) [size=4K]
> Capabilities: [44] Vital Product Data
> Capabilities: [4c] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 0000:02:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev
> 08)
> Subsystem: Creative Labs CT4850 SBLive! Value
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (500ns min, 5000ns max)
> Interrupt: pin A routed to IRQ 23
> Region 0: I/O ports at cc00 [size=32]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 0000:02:0b.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev
> 08)
> Subsystem: Creative Labs Gameport Joystick
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64
> Region 0: I/O ports at d000 [size=8]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 0000:02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev
> 74)
> Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 0x04 (16 bytes)
> Interrupt: pin A routed to IRQ 20
> Region 0: I/O ports at c880 [size=128]
> Region 1: Memory at f7fff000 (32-bit, non-prefetchable) [size=128]
> Expansion ROM at f7fc0000 [disabled] [size=128K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
> Jeremy
>
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-07 15:12 ` Mauro Carvalho Chehab
@ 2005-07-07 15:35 ` Jeremy Laine
2005-07-07 16:17 ` matthieu castet
1 sibling, 0 replies; 18+ messages in thread
From: Jeremy Laine @ 2005-07-07 15:35 UTC (permalink / raw)
To: Mauro Carvalho Chehab; +Cc: linux-kernel, video4linux-list
Hi Mauro,
First of all, many thanks for taking the time to reply to my email!
> We don't have any other OOPS reported for BTTV cards.
The reply from Bodo Eggert seems to indicate otherwise..
Here is some extra information as requested:
> 1) desactivate any overclocking at motherboard/video board;
I do not use any kind of overclocking, never have done and never will!
> 2) use a standard vanilla kernel (not a distro kernel, that may have
> some experimental patches applied;
The crashes I reported were on a vanilla 2.6.12 kernel, compiled straight from
the tarball on kernel.org.
> 3) use a minimum ammount of cards leaving only neccessary cards at MB.
> For these, it is good to clean its contacts;
The only extension cards I use are:
- 1 nVidia GeForce 6800 video adapter
- 1 Pinacle PCTV card
- 1 3Com 3c905C ethernet card
- 1 SB Live! 1024 card
I regularly vacuum-clean my tower and have checked the contacts on the extension
cards on several occasions. For tests, I am willing to remove the NIC +
soundcard if you think that will help (will try over the weekend), but in the
long run I don't consider any of the above cards to be "exotic" or optional..
> 4) Test it again.
Will do, as stated above. On a sidenote, so far I have been unable to reproduce
the problem when PREEMPT is disactivated (I stressed my box by compiling a
kernel while watching TV).
Cheers,
Jeremy
--
http://www.jerryweb.org/ : JerryWeb.org
http://sailcut.sourceforge.net/ : Sailcut CAD
http://opensource.polytechnique.org/ : Polytechnique.org Free Software
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
[not found] ` <4nrlt-8po-13@gated-at.bofh.it>
@ 2005-07-07 15:52 ` Bodo Eggert
2005-07-08 17:19 ` Mauro Carvalho Chehab
0 siblings, 1 reply; 18+ messages in thread
From: Bodo Eggert @ 2005-07-07 15:52 UTC (permalink / raw)
To: 7eggert, Jeremy Laine, linux-kernel
Bodo Eggert <harvested.in.lkml@posting.7eggert.dyndns.org> wrote:
> Now I've upgraded to X.org 6.8.2 and done a first stress-test (copying
> large files from network to local HDD), and I still can post.
It occured again. So it wasn't that easy.
--
Ich danke GMX dafür, die Verwendung meiner Adressen mittels per SPF
verbreiteten Lügen zu sabotieren.
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-07 15:12 ` Mauro Carvalho Chehab
2005-07-07 15:35 ` Jeremy Laine
@ 2005-07-07 16:17 ` matthieu castet
2005-07-07 19:11 ` Duncan Sands
1 sibling, 1 reply; 18+ messages in thread
From: matthieu castet @ 2005-07-07 16:17 UTC (permalink / raw)
To: Linux and Kernel Video; +Cc: Jeremy Laine, linux-kernel
Hi,
Mauro Carvalho Chehab wrote:
> Jeremy,
>
> BTTV cards uses massive data transfer via DMA when you are watching TV,
> transfering one screen every 1/30 s. Maybe you are suffering from a
> trouble on your motherboard or at board physical connection.
>
I had (have ?) similar problem with a bt878 :
if I use bttv orverlay and do disk IO (a `grep toto /usr' for example),
there quickly RISC corruption message and my log and also ext3
corruption (that's why except for recovering epg data, I don't use
anymore my card).
There were a similar report were someone and mozilla corruption when
watching tv.
When using gradisplay, I don't saw faillure, but I don't try for a long
time.
Jeremy do you use overlay or gradisplay ?
Matthieu
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-07 16:17 ` matthieu castet
@ 2005-07-07 19:11 ` Duncan Sands
0 siblings, 0 replies; 18+ messages in thread
From: Duncan Sands @ 2005-07-07 19:11 UTC (permalink / raw)
To: matthieu castet; +Cc: Linux and Kernel Video, Jeremy Laine, linux-kernel
> Jeremy do you use overlay or gradisplay ?
Dunno about Jeremy, but I'm using overlay and getting hard
hangs.
Ciao,
D.
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-07 15:52 ` Bodo Eggert
@ 2005-07-08 17:19 ` Mauro Carvalho Chehab
2005-07-09 7:34 ` Bodo Eggert
0 siblings, 1 reply; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2005-07-08 17:19 UTC (permalink / raw)
To: 7eggert; +Cc: Jeremy Laine, linux-kernel, v4l >> Linux and Kernel Video
Bodo Eggert wrote:
> Bodo Eggert <harvested.in.lkml@posting.7eggert.dyndns.org> wrote:
>
>
>>Now I've upgraded to X.org 6.8.2 and done a first stress-test (copying
>>large files from network to local HDD), and I still can post.
>
>
> It occured again. So it wasn't that easy.
Bodo/Jeremy/Castet,
It looks to be an old reported trouble with bttv cards.
There is a doc at kernel that treats this subject. It is at:
Documentation/video4linux/bttv/README.freeze
Overlay works by transfering data from BTTV card directelly to Video Card.
This looks to be problem related to DMA troubles on some motherboards.
Some chipsets (via being most prominent) have problems with DMA
transfers between two PCI cards (or PCI to AGP) that affects overlay. It
may also be related with multiple devices using DMA at the same time.
Castet did mention, on this thread, that this is causing also disk
corruption on his machine, with is an inication that this is the case.
Anyway, it doesn't seem to be a V4L specific issue.
Mauro.
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12)
2005-07-08 17:19 ` Mauro Carvalho Chehab
@ 2005-07-09 7:34 ` Bodo Eggert
0 siblings, 0 replies; 18+ messages in thread
From: Bodo Eggert @ 2005-07-09 7:34 UTC (permalink / raw)
To: Mauro Carvalho Chehab
Cc: 7eggert, Jeremy Laine, linux-kernel,
v4l @pop3.web.de>> Linux and Kernel Video
On Fri, 8 Jul 2005, Mauro Carvalho Chehab wrote:
> It looks to be an old reported trouble with bttv cards.
>
> There is a doc at kernel that treats this subject. It is at:
> Documentation/video4linux/bttv/README.freeze
>
>
> Overlay works by transfering data from BTTV card directelly to Video Card.
>
> This looks to be problem related to DMA troubles on some motherboards.
I've found the no_overlay parameter to be promising, but it seems to be
unused by the driver:
$ grep -r no_overlay drivers/*
drivers/media/video/bttv-cards.c:static unsigned int no_overlay=-1;
drivers/media/video/bttv-cards.c:module_param(no_overlay, int, 0444);
drivers/media/video/bttv-cards.c: if (UNSET == no_overlay) {
drivers/media/video/bttv-cards.c: no_overlay = 1;
$
It seems some patch has removed that feature, and I have no grepable pile
of patches here nor an idea (except for google) where I can get one.
--
Top 100 things you don't want the sysadmin to say:
80. I cleaned up the root partition and now there's LOTS of free space.
^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2005-07-09 7:34 UTC | newest]
Thread overview: 18+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-07-06 10:11 OOPS: frequent crashes with bttv in 2.6.X series (inc. 2.6.12) Jeremy Laine
2005-07-06 14:44 ` Michael Krufky
2005-07-07 14:31 ` Lee Revell
2005-07-07 14:35 ` Michael Krufky
2005-07-06 14:59 ` Alexey Dobriyan
2005-07-07 8:25 ` Jeremy Laine
2005-07-07 15:12 ` Mauro Carvalho Chehab
2005-07-07 15:35 ` Jeremy Laine
2005-07-07 16:17 ` matthieu castet
2005-07-07 19:11 ` Duncan Sands
-- strict thread matches above, loose matches on Subject: below --
2005-07-06 15:02 Piszcz, Justin
2005-07-06 20:46 ` Lee Revell
[not found] <4njei-1Ps-21@gated-at.bofh.it>
2005-07-06 23:09 ` Bodo Eggert
2005-07-07 8:17 ` Duncan Sands
2005-07-07 8:31 ` Jeremy Laine
[not found] <4nrlt-8po-15@gated-at.bofh.it>
[not found] ` <4nrlt-8po-13@gated-at.bofh.it>
2005-07-07 15:52 ` Bodo Eggert
2005-07-08 17:19 ` Mauro Carvalho Chehab
2005-07-09 7:34 ` Bodo Eggert
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox