Re: IT8212/ITE RAID

[CaT <cat@zip.com.au>]

On Sun, Aug 14, 2005 at 02:33:05PM +0100, Alan Cox wrote:
> What does a full identify data set for the drive look like ?

Here it is for the two drives. Please note that multisect was turned on
manually as well as the security freeze.


/dev/hda:

ATA device, with non-removable media
        Model Number:       ST3200822A                              
        Serial Number:      3LJ22Y8F
        Firmware Revision:  3.01    
Standards:
        Used: ATA/ATAPI-6 T13 1410D revision 2 
        Supported: 6 5 4 3 
Configuration:
        Logical         max     current
        cylinders       16383   65535
        heads           16      1
        sectors/track   63      63
        --
        CHS current addressable sectors:    4128705
        LBA    user addressable sectors:  268435455
        LBA48  user addressable sectors:  390721968
        device size with M = 1024*1024:      190782 MBytes
        device size with M = 1000*1000:      200049 MBytes (200 GB)
Capabilities:
        LBA, IORDY(can be disabled)
        bytes avail on r/w long: 4      Queue depth: 1
        Standby timer values: spec'd by Standard, no device specific minimum
        R/W multiple sector transfer: Max = 16  Current = 16
        Recommended acoustic management value: 128, current value: 0
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4 
             Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    READ BUFFER cmd
           *    WRITE BUFFER cmd
           *    Host Protected Area feature set
           *    Look-ahead
           *    Write cache
           *    Power Management feature set
                Security Mode feature set
           *    FLUSH CACHE EXT command
           *    Mandatory FLUSH CACHE command 
           *    48-bit Address feature set 
                SET MAX security extension
Security: 
                supported
        not     enabled
        not     locked
                frozen
        not     expired: security count
        not     supported: enhanced erase
HW reset results:
        CBLID- above Vih
        Device num = 0 determined by CSEL
Checksum: correct

/dev/hdc:

ATA device, with non-removable media
powers-up in standby; SET FEATURES subcmd spins-up.
        Model Number:       IC35L060AVV207-0                        
        Serial Number:      VNVB01G2RAK8XH
        Firmware Revision:  V22OA63A
Standards:
        Used: ATA/ATAPI-6 T13 1410D revision 3a 
        Supported: 6 5 4 3 
Configuration:
        Logical         max     current
        cylinders       16383   16383
        heads           16      16
        sectors/track   63      63
        --
        CHS current addressable sectors:   16514064
        LBA    user addressable sectors:  120103200
        LBA48  user addressable sectors:  120103200
        device size with M = 1024*1024:       58644 MBytes
        device size with M = 1000*1000:       61492 MBytes (61 GB)
Capabilities:
        LBA, IORDY(can be disabled)
        bytes avail on r/w long: 52     Queue depth: 32
        Standby timer values: spec'd by Standard, no device specific minimum
        R/W multiple sector transfer: Max = 16  Current = 16
        Advanced power management level: unknown setting (0x0000)
        Recommended acoustic management value: 128, current value: 254
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4 
             Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    NOP cmd
           *    READ BUFFER cmd
           *    WRITE BUFFER cmd
           *    Host Protected Area feature set
                Release interrupt
           *    Look-ahead
           *    Write cache
           *    Power Management feature set
                Security Mode feature set
           *    FLUSH CACHE EXT command
           *    Mandatory FLUSH CACHE command 
           *    48-bit Address feature set 
                Automatic Acoustic Management feature set 
                SET MAX security extension
                Address Offset Reserved Area Boot
                SET FEATURES subcommand required to spinup after power up
                Power-Up In Standby feature set
                Advanced Power Management feature set
           *    General Purpose Logging feature set
Security: 
        Master password revision code = 65534
                supported
        not     enabled
        not     locked
                frozen
        not     expired: security count
        not     supported: enhanced erase
        30min for SECURITY ERASE UNIT. 
HW reset results:
        CBLID- above Vih
        Device num = 0 determined by the jumper
Checksum: correct

-- 
    "To the extent that we overreact, we proffer the terrorists the
    greatest tribute."
    	- High Court Judge Michael Kirby