From: Dipankar Sarma <dipankar@in.ibm.com>
To: linux-scsi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Subject: [2.6.14-rc1] sym scsi boot hang
Date: Tue, 13 Sep 2005 18:18:04 +0530 [thread overview]
Message-ID: <20050913124804.GA5008@in.ibm.com> (raw)
My ppc64 box refuses to boot with 2.6.14-rc1. The console log
is included below. I see a lot of repeat of the last message
in the log and then the box hangs.
Any idea what might have caused this ?
Thanks
Dipankar
sym0: <1010-66> rev 0x1 at pci 0001:01:01.0 irq 115
sym0: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.1
target0:0:8: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
Vendor: IBM Model: IC35L036UCDY10-0 Rev: S25M
Type: Direct-Access ANSI SCSI revision: 03
target0:0:8: tagged command queuing enabled, command queue depth 16.
target0:0:8: Beginning Domain Validation
target0:0:8: asynchronous.
target0:0:8: wide asynchronous.
target0:0:8: FAST-80 WIDE SCSI 160.0 MB/s DT IU QAS (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:8: Write Buffer failure 700ff
target0:0:8: Domain Validation Disabing Information Units
target0:0:8: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:8: Write Buffer failure 700ff
target0:0:8: Domain Validation detected failure, dropping back
target0:0:8: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:8: Ending Domain Validation
target0:0:9: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
Vendor: IBM Model: IC35L036UCDY10-0 Rev: S25M
Type: Direct-Access ANSI SCSI revision: 03
target0:0:9: tagged command queuing enabled, command queue depth 16.
target0:0:9: Beginning Domain Validation
target0:0:9: asynchronous.
target0:0:9: wide asynchronous.
target0:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT IU QAS (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:9: Write Buffer failure 700ff
target0:0:9: Domain Validation Disabing Information Units
target0:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:9: Write Buffer failure 700ff
target0:0:9: Domain Validation detected failure, dropping back
target0:0:9: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:9: Ending Domain Validation
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
Vendor: IBM Model: IC35L036UCDY10-0 Rev: S25M
Type: Direct-Access ANSI SCSI revision: 03
target0:0:10: tagged command queuing enabled, command queue depth 16.
target0:0:10: Beginning Domain Validation
target0:0:10: asynchronous.
target0:0:10: wide asynchronous.
target0:0:10: Domain Validation skipping write tests
target0:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT IU QAS (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:10: Domain Validation Disabing Information Units
target0:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:10: Domain Validation detected failure, dropping back
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: Ending Domain Validation
Vendor: IBM Model: HSBPM2 PU2SCSI Rev: 0016
Type: Enclosure ANSI SCSI revision: 02
target0:0:14: Beginning Domain Validation
0:0:14:0: phase change 6-7 9@100503a8 resid=7.
0:0:14:0: phase change 6-7 9@100503a8 resid=7.
0:0:14:0: phase change 6-7 9@100503a8 resid=7.
0:0:14:0: phase change 6-7 9@100503a8 resid=7.
target0:0:14: Ending Domain Validation
Vendor: IBM Model: HSBPD4M PU3SCSI Rev: 0016
Type: Enclosure ANSI SCSI revision: 02
target0:0:15: Beginning Domain Validation
0:0:15:0: phase change 6-7 9@100503a8 resid=7.
0:0:15:0: phase change 6-7 9@100503a8 resid=7.
0:0:15:0: phase change 6-7 9@100503a8 resid=7.
0:0:15:0: phase change 6-7 9@100503a8 resid=7.
target0:0:15: Ending Domain Validation
sym1: <1010-66> rev 0x1 at pci 0001:01:01.1 irq 116
sym1: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi1 : sym-2.2.1
sym2: <1010-66> rev 0x1 at pci 0001:41:01.0 irq 119
sym2: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym2: SCSI BUS has been reset.
scsi2 : sym-2.2.1
sym3: <1010-66> rev 0x1 at pci 0001:41:01.1 irq 120
sym3: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym3: SCSI BUS has been reset.
scsi3 : sym-2.2.1
st: Version 20050830, fixed bufsize 32768, s/g segs 256
SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sda: drive cache: write through
SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sda: drive cache: write through
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
Attached scsi disk sda at scsi0, channel 0, id 8, lun 0
SCSI device sdb: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sdb: drive cache: write through
SCSI device sdb: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sdb: drive cache: write through
sdb: sdb1 sdb2
Attached scsi disk sdb at scsi0, channel 0, id 9, lun 0
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
sdc: Spinning up disk....<6> target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
next reply other threads:[~2005-09-13 12:55 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-09-13 12:48 Dipankar Sarma [this message]
2005-09-13 13:17 ` [2.6.14-rc1] sym scsi boot hang Anton Blanchard
2005-09-13 14:29 ` Anton Blanchard
2005-09-13 16:35 ` James Bottomley
2005-09-13 16:47 ` Anton Blanchard
2005-09-13 17:32 ` James Bottomley
2005-09-13 17:13 ` Anton Blanchard
2005-09-13 17:33 ` Dipankar Sarma
2005-09-14 8:06 ` Anton Blanchard
2005-09-14 15:49 ` Alan Stern
2005-09-14 16:52 ` Mike Christie
2005-09-14 16:53 ` Mike Christie
2005-09-14 20:35 ` James Bottomley
2005-09-14 16:57 ` James Bottomley
2005-09-14 20:19 ` Alan Stern
2005-09-14 20:44 ` James Bottomley
2005-09-14 21:33 ` Alan Stern
2005-09-15 13:56 ` James Bottomley
2005-09-15 14:13 ` Alan Stern
2005-09-15 17:52 ` Alan Stern
2005-09-16 10:28 ` Anton Blanchard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20050913124804.GA5008@in.ibm.com \
--to=dipankar@in.ibm.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox