* 2.4.32 Oops in scsi_dispatch_cmd
@ 2005-12-07 9:37 Jan Oberländer
2005-12-07 21:50 ` Willy Tarreau
0 siblings, 1 reply; 4+ messages in thread
From: Jan Oberländer @ 2005-12-07 9:37 UTC (permalink / raw)
To: linux-kernel
[-- Attachment #1.1: Type: text/plain, Size: 2661 bytes --]
Hi,
[please Cc:, I'm not on the list!]
I've been receiving Oops repeatedly in scsi_dispatch_cmd, in different
kernels (2.4.{27,31,32}). At first I thought that a non-free module for
an ATA RAID card was responsible, but in 2.4.32 I've seen it without
using that as well (in a non-tainted kernel). I can't exactly rule out
that it's a hardware problem, but since it's very repeatable I'm really
not sure. The box doesn't recover from the Oops, but I was still able
to see the Oops message in /var/log/messages. See the attached file for
ksymoops output.
The tar process is run from a backup scripts that mounts an IDE drive
partition, writes a backup to it and unmounts it. It's always been the
tar process behind this crash. Some system details:
$ uname -a
Linux server 2.4.32 #1 Tue Dec 6 10:55:41 CET 2005 i686 GNU/Linux
$ cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 7
model name : AMD Duron(tm) Processor
stepping : 1
cpu MHz : 1197.726
cache size : 64 KB
[...]
$ lspci
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
0000:00:0d.0 SCSI storage controller: Adaptec AHA-2940U2/U2W
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
0000:01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15)
$
There are no modules loaded. The IDE HDD is on the VIA controller,
several other disks are behind the Adaptec controller (several of them
on Software RAID).
Maybe you have an idea what's going on (or who to talk to instead)? I'm
stuck.
Thanks in advance & keep up the good work!
Jan
--
+-------------------------------------+
| Jan Oberländer <mindriot@gmx.net> |
| PGP key: 0xC4D910E3 |
+-------------------------------------+
[-- Attachment #1.2: crash.symoops --]
[-- Type: text/plain, Size: 4467 bytes --]
ksymoops 2.4.9 on i686 2.4.32. Options used
-V (default)
-k /proc/ksyms (specified)
-l /proc/modules (specified)
-o /lib/modules/2.4.32/ (specified)
-m /boot/System.map-2.4.32 (specified)
No modules in ksyms, skipping objects
Warning (read_lsmod): no symbols in lsmod, is /proc/modules a valid lsmod file?
Dec 7 01:11:46 server kernel: c01cdd9b
Dec 7 01:11:46 server kernel: Oops: 0000
Dec 7 01:11:46 server kernel: CPU: 0
Dec 7 01:11:46 server kernel: EIP: 0010:[scsi_dispatch_cmd+107/544] Not tainted
Dec 7 01:11:46 server kernel: EFLAGS: 00010246
Dec 7 01:11:46 server kernel: eax: 00000000 ebx: c02d7da0 ecx: c13be088 edx: 000000c8
Dec 7 01:11:46 server kernel: esi: c12e5480 edi: cff3edc0 ebp: c13be000 esp: c97b5e58
Dec 7 01:11:46 server kernel: ds: 0018 es: 0018 ss: 0018
Dec 7 01:11:46 server kernel: Process tar (pid: 10731, stackpage=c97b5000)
Dec 7 01:11:46 server kernel: Stack: ce072e40 c01ce410 00000018 00000000 c02d7da0 c12e5480 c13be110 c13be000
Dec 7 01:11:46 server kernel: c01d4ecf c13be000 00000000 00000000 00000001 00001000 c13be0b8 c12e54bc
Dec 7 01:11:46 server kernel: c02d7da0 cff1edc0 c12e5480 00000296 c97b5ec8 c97b5ee8 c12c0338 c01a5259
Dec 7 01:11:46 server kernel: Call Trace: [scsi_done+0/160] [scsi_request_fn+431/880] [generic_unplug_device+57/64] [__run_task_queue+75/96] [block_sync_page+33/48]
Dec 7 01:11:46 server kernel: Code: f6 40 67 04 0f 84 5a 01 00 00 c7 44 24 08 30 1c 1d c0 8b 45
Using defaults from ksymoops -t elf32-i386 -a i386
>>ebx; c02d7da0 <sd_template+0/48>
Code; 00000000 Before first symbol
00000000 <_EIP>:
Code; 00000000 Before first symbol
0: f6 40 67 04 testb $0x4,0x67(%eax)
Code; 00000004 Before first symbol
4: 0f 84 5a 01 00 00 je 164 <_EIP+0x164>
Code; 0000000a Before first symbol
a: c7 44 24 08 30 1c 1d movl $0xc01d1c30,0x8(%esp)
Code; 00000011 Before first symbol
11: c0
Code; 00000012 Before first symbol
12: 8b 45 00 mov 0x0(%ebp),%eax
Dec 7 01:11:46 server kernel: <1>Unable to handle kernel NULL pointer dereference at virtual address 00000011
Dec 7 01:11:46 server kernel: c0114cd2
Dec 7 01:11:46 server kernel: Oops: 0000
Dec 7 01:11:46 server kernel: CPU: 0
Dec 7 01:11:46 server kernel: EIP: 0010:[__wake_up+146/176] Not tainted
Dec 7 01:11:46 server kernel: EFLAGS: 00010046
Dec 7 01:11:46 server kernel: eax: 00000000 ebx: c97b5ef8 ecx: c9268000 edx: 00000011
Dec 7 01:11:46 server kernel: esi: c116b5c8 edi: c12c0338 ebp: cae05ea8 esp: cae05e90
Dec 7 01:11:46 server kernel: ds: 0018 es: 0018 ss: 0018
Dec 7 01:11:46 server kernel: Process sendmail (pid: 10848, stackpage=cae05000)
Dec 7 01:11:46 server kernel: Stack: 00000000 00000282 00000003 00000000 c116b5c8 08421065 cb06d3b4 c012552f
Dec 7 01:11:46 server kernel: cb5e5000 c4aa1000 c0130534 c11f4378 080edac4 cb0c5740 00000001 cb832d40
Dec 7 01:11:46 server kernel: c0125de2 cb0c5740 cb832d40 080edac4 cb06d3b4 08421065 c2770140 cb0c5740
Dec 7 01:11:46 server kernel: Call Trace: [do_wp_page+79/528] [__alloc_pages+100/608] [handle_mm_fault+242/256] [do_page_fault+440/1317] [build_mmap_rb+73/96]
Dec 7 01:11:46 server kernel: Code: 8b 02 89 d3 89 c2 0f 0d 00 39 fb 75 91 ff 75 ec 9d 83 c4 0c
Code; 00000000 Before first symbol
00000000 <_EIP>:
Code; 00000000 Before first symbol
0: 8b 02 mov (%edx),%eax
Code; 00000002 Before first symbol
2: 89 d3 mov %edx,%ebx
Code; 00000004 Before first symbol
4: 89 c2 mov %eax,%edx
Code; 00000006 Before first symbol
6: 0f 0d 00 prefetch (%eax)
Code; 00000009 Before first symbol
9: 39 fb cmp %edi,%ebx
Code; 0000000b Before first symbol
b: 75 91 jne ffffff9e <_EIP+0xffffff9e>
Code; 0000000d Before first symbol
d: ff 75 ec pushl 0xffffffec(%ebp)
Code; 00000010 Before first symbol
10: 9d popf
Code; 00000011 Before first symbol
11: 83 c4 0c add $0xc,%esp
Dec 7 01:11:46 server kernel: <1>Unable to handle kernel NULL pointer dereference at virtual address 00000011
1 warning issued. Results may not be reliable.
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 2.4.32 Oops in scsi_dispatch_cmd
2005-12-07 9:37 2.4.32 Oops in scsi_dispatch_cmd Jan Oberländer
@ 2005-12-07 21:50 ` Willy Tarreau
2005-12-07 22:52 ` Jan Oberländer
0 siblings, 1 reply; 4+ messages in thread
From: Willy Tarreau @ 2005-12-07 21:50 UTC (permalink / raw)
To: Jan Oberländer; +Cc: linux-kernel
Hi,
On Wed, Dec 07, 2005 at 10:37:47AM +0100, Jan Oberländer wrote:
> Hi,
>
> [please Cc:, I'm not on the list!]
>
> I've been receiving Oops repeatedly in scsi_dispatch_cmd, in different
> kernels (2.4.{27,31,32}). At first I thought that a non-free module for
> an ATA RAID card was responsible, but in 2.4.32 I've seen it without
> using that as well (in a non-tainted kernel). I can't exactly rule out
> that it's a hardware problem, but since it's very repeatable I'm really
> not sure. The box doesn't recover from the Oops, but I was still able
> to see the Oops message in /var/log/messages. See the attached file for
> ksymoops output.
could you send your .config and gcc version please ? I've checked the
code and it's not easy to find what data is accessed in your oopses.
> The tar process is run from a backup scripts that mounts an IDE drive
> partition, writes a backup to it and unmounts it. It's always been the
> tar process behind this crash. Some system details:
could you please also tell us what partition tar reads data from ? I've
understood that you have some disks on your adaptec card and some software
RAID, so if you could roughly explain the setup, it would be great.
> $ uname -a
> Linux server 2.4.32 #1 Tue Dec 6 10:55:41 CET 2005 i686 GNU/Linux
> $ cat /proc/cpuinfo
> processor : 0
> vendor_id : AuthenticAMD
> cpu family : 6
> model : 7
> model name : AMD Duron(tm) Processor
> stepping : 1
> cpu MHz : 1197.726
> cache size : 64 KB
> [...]
> $ lspci
> 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
> 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
> 0000:00:0d.0 SCSI storage controller: Adaptec AHA-2940U2/U2W
> 0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
> 0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
> 0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
> 0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
> 0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
> 0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
> 0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
> 0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
> 0000:01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15)
> $
>
> There are no modules loaded. The IDE HDD is on the VIA controller,
> several other disks are behind the Adaptec controller (several of them
> on Software RAID).
>
> Maybe you have an idea what's going on (or who to talk to instead)? I'm
> stuck.
It may be doable with a few more info. Please also confirm that your
System.map really matches your kernel (for the oops report).
> Thanks in advance & keep up the good work!
>
> Jan
Regards,
Willy
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 2.4.32 Oops in scsi_dispatch_cmd
2005-12-07 21:50 ` Willy Tarreau
@ 2005-12-07 22:52 ` Jan Oberländer
2005-12-08 20:16 ` Willy TARREAU
0 siblings, 1 reply; 4+ messages in thread
From: Jan Oberländer @ 2005-12-07 22:52 UTC (permalink / raw)
To: linux-kernel
[-- Attachment #1.1: Type: text/plain, Size: 2312 bytes --]
On Wed, Dec 07, 2005 at 10:50:14PM +0100, Willy Tarreau wrote:
> On Wed, Dec 07, 2005 at 10:37:47AM +0100, Jan Oberländer wrote:
> > I've been receiving Oops repeatedly
>
> could you send your .config and gcc version please ? I've checked the
> code and it's not easy to find what data is accessed in your oopses.
I attached the .config.
$ gcc -v
Reading specs from /usr/lib/gcc-lib/i486-linux/3.3.5/specs
Configured with: ../src/configure -v
--enable-languages=c,c++,java,f77,pascal,objc,ada,treelang --prefix=/usr
--mandir=/usr/share/man --infodir=/usr/share/info
--with-gxx-include-dir=/usr/include/c++/3.3 --enable-shared
--enable-__cxa_atexit --with-system-zlib --enable-nls
--without-included-gettext --enable-clocale=gnu --enable-debug
--enable-java-gc=boehm --enable-java-awt=xlib --enable-objc-gc
i486-linux
Thread model: posix
gcc version 3.3.5 (Debian 1:3.3.5-13)
> > The tar process is run from a backup scripts that mounts an IDE
> > drive partition, writes a backup to it and unmounts it. It's always
> > been the tar process behind this crash. Some system details:
>
> could you please also tell us what partition tar reads data from ?
> I've understood that you have some disks on your adaptec card and some
> software RAID, so if you could roughly explain the setup, it would be
> great.
The setup:
/dev/hda on onboard IDE
/dev/sd{a,b,c,d,e,f} on Adaptec
md0 : active raid5 sdd1[2] sdc1[1] sdb1[0]
md1 : active raid5 sdd2[2] sdc2[1] sdb2[0]
md3 : active raid5 sdd3[2] sdc3[1] sdb3[0]
md2 : active raid1 sdf1[1] sde1[0]
The backup script roughly does the following:
1. mount hda
2. backup data from the md*,sd* devices to hda
3. umount hda
As I said, the IDE drive was on an ATA RAID card at first, visible to
the system as /dev/sdg. I changed this because of the tainted ATA RAID
module, but I'm receiving the same oops either way.
> It may be doable with a few more info. Please also confirm that your
> System.map really matches your kernel (for the oops report).
I double-checked.
Tell me if you need any further information.
Best wishes,
Jan
--
+-------------------------------------+
| Jan Oberländer <mindriot@gmx.net> |
| PGP key: 0xC4D910E3 |
+-------------------------------------+
[-- Attachment #1.2: .config --]
[-- Type: text/plain, Size: 23906 bytes --]
#
# Automatically generated by make menuconfig: don't edit
#
CONFIG_X86=y
# CONFIG_SBUS is not set
CONFIG_UID16=y
#
# Code maturity level options
#
# CONFIG_EXPERIMENTAL is not set
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MK8 is not set
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_HAS_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_PGE=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_F00F_WORKS_OK=y
CONFIG_X86_MCE=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_HIGHMEM is not set
# CONFIG_MATH_EMULATION is not set
# CONFIG_MTRR is not set
# CONFIG_SMP is not set
# CONFIG_X86_UP_APIC is not set
# CONFIG_X86_UP_IOAPIC is not set
# CONFIG_X86_TSC_DISABLE is not set
CONFIG_X86_TSC=y
#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_ISA=y
CONFIG_PCI_NAMES=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
CONFIG_HOTPLUG=y
#
# PCMCIA/CardBus support
#
# CONFIG_PCMCIA is not set
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
# CONFIG_HOTPLUG_PCI_COMPAQ is not set
# CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM is not set
# CONFIG_HOTPLUG_PCI_SHPC is not set
# CONFIG_HOTPLUG_PCI_SHPC_POLL_EVENT_MODE is not set
# CONFIG_HOTPLUG_PCI_SHPC_PHPRM_LEGACY is not set
# CONFIG_HOTPLUG_PCI_PCIE is not set
# CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE is not set
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
# CONFIG_OOM_KILLER is not set
CONFIG_PM=y
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_RTC_IS_GMT is not set
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set
#
# ACPI Support
#
# CONFIG_ACPI is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_PC_CML1=y
# CONFIG_PARPORT_SERIAL is not set
# CONFIG_PARPORT_PC_PCMCIA is not set
# CONFIG_PARPORT_AMIGA is not set
# CONFIG_PARPORT_MFC3 is not set
# CONFIG_PARPORT_ATARI is not set
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_SUNBPP is not set
# CONFIG_PARPORT_IP22 is not set
# CONFIG_PARPORT_OTHER is not set
CONFIG_PARPORT_1284=y
#
# Plug and Play configuration
#
CONFIG_PNP=y
CONFIG_ISAPNP=y
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_CISS_SCSI_TAPE is not set
# CONFIG_CISS_MONITOR_THREAD is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=4096
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_BLK_STATS is not set
#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=y
CONFIG_MD_RAID0=y
CONFIG_MD_RAID1=y
CONFIG_MD_RAID5=y
# CONFIG_MD_MULTIPATH is not set
# CONFIG_BLK_DEV_LVM is not set
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
# CONFIG_NETLINK_DEV is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_FILTER=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_INET_ECN is not set
# CONFIG_SYN_COOKIES is not set
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_FTP=m
# CONFIG_IP_NF_AMANDA is not set
# CONFIG_IP_NF_TFTP is not set
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
# CONFIG_IP_NF_MATCH_MARK is not set
# CONFIG_IP_NF_MATCH_MULTIPORT is not set
# CONFIG_IP_NF_MATCH_TOS is not set
# CONFIG_IP_NF_MATCH_RECENT is not set
# CONFIG_IP_NF_MATCH_ECN is not set
# CONFIG_IP_NF_MATCH_DSCP is not set
# CONFIG_IP_NF_MATCH_AH_ESP is not set
# CONFIG_IP_NF_MATCH_LENGTH is not set
# CONFIG_IP_NF_MATCH_TTL is not set
# CONFIG_IP_NF_MATCH_TCPMSS is not set
# CONFIG_IP_NF_MATCH_HELPER is not set
# CONFIG_IP_NF_MATCH_STATE is not set
# CONFIG_IP_NF_MATCH_CONNTRACK is not set
CONFIG_IP_NF_FILTER=m
# CONFIG_IP_NF_TARGET_REJECT is not set
# CONFIG_IP_NF_NAT is not set
# CONFIG_IP_NF_MANGLE is not set
# CONFIG_IP_NF_TARGET_LOG is not set
# CONFIG_IP_NF_TARGET_ULOG is not set
# CONFIG_IP_NF_TARGET_TCPMSS is not set
# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_NF_COMPAT_IPCHAINS is not set
# CONFIG_IP_NF_COMPAT_IPFWADM is not set
#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
# CONFIG_PHONE_IXJ_PCMCIA is not set
#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y
#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set
# CONFIG_BLK_DEV_IDECS is not set
# CONFIG_BLK_DEV_DELKIN is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=m
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_BLK_DEV_GENERIC is not set
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_BLK_DEV_ADMA100 is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_AMD74XX_OVERRIDE is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
CONFIG_BLK_DEV_HPT366=y
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
CONFIG_BLK_DEV_RZ1000=y
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
# CONFIG_DMA_NONPCI is not set
# CONFIG_BLK_DEV_ATARAID is not set
# CONFIG_BLK_DEV_ATARAID_PDC is not set
# CONFIG_BLK_DEV_ATARAID_HPT is not set
# CONFIG_BLK_DEV_ATARAID_MEDLEY is not set
# CONFIG_BLK_DEV_ATARAID_SII is not set
#
# SCSI support
#
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SD_EXTRA_DEVS=40
CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_SR_EXTRA_DEVS=2
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_DEBUG_QUEUES=y
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=32
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
# CONFIG_AIC7XXX_PROBE_EISA_VL is not set
# CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
CONFIG_AIC7XXX_DEBUG_MASK=0
# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_MEGARAID2 is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_SATA_AHCI is not set
# CONFIG_SCSI_SATA_SVW is not set
# CONFIG_SCSI_ATA_PIIX is not set
# CONFIG_SCSI_SATA_NV is not set
# CONFIG_SCSI_SATA_QSTOR is not set
# CONFIG_SCSI_SATA_PROMISE is not set
# CONFIG_SCSI_SATA_SX4 is not set
# CONFIG_SCSI_SATA_SIL is not set
# CONFIG_SCSI_SATA_SIS is not set
# CONFIG_SCSI_SATA_ULI is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_BOOT is not set
# CONFIG_FUSION_ISENSE is not set
# CONFIG_FUSION_CTL is not set
# CONFIG_FUSION_LAN is not set
#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_LAN is not set
# CONFIG_I2O_SCSI is not set
# CONFIG_I2O_PROC is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_NET_SB1000 is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_SUNLANCE is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNBMAC is not set
# CONFIG_SUNQE is not set
# CONFIG_SUNGEM is not set
CONFIG_NET_VENDOR_3COM=y
CONFIG_EL1=m
CONFIG_EL2=m
CONFIG_ELPLUS=m
# CONFIG_EL16 is not set
CONFIG_EL3=m
CONFIG_3C515=m
# CONFIG_ELMC is not set
# CONFIG_ELMC_II is not set
CONFIG_VORTEX=m
CONFIG_TYPHOON=m
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_B44 is not set
# CONFIG_CS89x0 is not set
CONFIG_TULIP=m
# CONFIG_TULIP_MWI is not set
# CONFIG_TULIP_MMIO is not set
CONFIG_DE4X5=m
# CONFIG_DGRS is not set
# CONFIG_DM9102 is not set
CONFIG_EEPRO100=m
# CONFIG_EEPRO100_PIO is not set
# CONFIG_E100 is not set
# CONFIG_LNE390 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
CONFIG_NE2K_PCI=m
# CONFIG_FORCEDETH is not set
# CONFIG_NE3210 is not set
# CONFIG_ES3210 is not set
# CONFIG_8139CP is not set
CONFIG_8139TOO=m
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_OLD_RX_RESET is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_SUNDANCE_MMIO is not set
# CONFIG_TLAN is not set
CONFIG_VIA_RHINE=y
# CONFIG_VIA_RHINE_MMIO is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_MYRI_SBUS is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_FDDI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
# CONFIG_PPP_FILTER is not set
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
# CONFIG_SLIP is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
CONFIG_ISDN=m
CONFIG_ISDN_BOOL=y
CONFIG_ISDN_PPP=y
# CONFIG_IPPP_FILTER is not set
# CONFIG_ISDN_PPP_VJ is not set
# CONFIG_ISDN_MPP is not set
CONFIG_ISDN_PPP_BSDCOMP=m
# CONFIG_ISDN_AUDIO is not set
# CONFIG_ISDN_X25 is not set
#
# ISDN feature submodules
#
# CONFIG_ISDN_DRV_LOOP is not set
# CONFIG_ISDN_DIVERSION is not set
#
# Passive ISDN cards
#
CONFIG_ISDN_DRV_HISAX=m
CONFIG_ISDN_HISAX=y
# CONFIG_HISAX_EURO is not set
# CONFIG_HISAX_1TR6 is not set
# CONFIG_HISAX_NI1 is not set
CONFIG_HISAX_MAX_CARDS=8
CONFIG_HISAX_16_0=y
CONFIG_HISAX_16_3=y
CONFIG_HISAX_AVM_A1=y
# CONFIG_HISAX_IX1MICROR2 is not set
# CONFIG_HISAX_ASUSCOM is not set
# CONFIG_HISAX_TELEINT is not set
# CONFIG_HISAX_HFCS is not set
# CONFIG_HISAX_SPORTSTER is not set
# CONFIG_HISAX_MIC is not set
# CONFIG_HISAX_ISURF is not set
# CONFIG_HISAX_HSTSAPHIR is not set
# CONFIG_HISAX_TELESPCI is not set
# CONFIG_HISAX_S0BOX is not set
CONFIG_HISAX_FRITZPCI=y
# CONFIG_HISAX_AVM_A1_PCMCIA is not set
# CONFIG_HISAX_ELSA is not set
# CONFIG_HISAX_DIEHLDIVA is not set
# CONFIG_HISAX_SEDLBAUER is not set
# CONFIG_HISAX_NETJET is not set
# CONFIG_HISAX_NETJET_U is not set
# CONFIG_HISAX_NICCY is not set
# CONFIG_HISAX_BKM_A4T is not set
# CONFIG_HISAX_SCT_QUADRO is not set
# CONFIG_HISAX_GAZEL is not set
# CONFIG_HISAX_HFC_PCI is not set
# CONFIG_HISAX_W6692 is not set
# CONFIG_HISAX_HFC_SX is not set
# CONFIG_HISAX_DEBUG is not set
# CONFIG_HISAX_SEDLBAUER_CS is not set
# CONFIG_HISAX_ELSA_CS is not set
# CONFIG_HISAX_AVM_A1_CS is not set
# CONFIG_HISAX_ST5481 is not set
# CONFIG_HISAX_FRITZ_PCIPNP is not set
# CONFIG_USB_AUERISDN is not set
#
# Active ISDN cards
#
# CONFIG_ISDN_DRV_ICN is not set
# CONFIG_ISDN_DRV_PCBIT is not set
# CONFIG_ISDN_DRV_SC is not set
# CONFIG_ISDN_DRV_ACT2000 is not set
# CONFIG_ISDN_DRV_EICON is not set
# CONFIG_ISDN_CAPI is not set
# CONFIG_HYSDN is not set
# CONFIG_HYSDN_CAPI is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Input core support
#
# CONFIG_INPUT is not set
# CONFIG_INPUT_KEYBDEV is not set
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_UINPUT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
# CONFIG_SERIAL_CONSOLE is not set
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
# CONFIG_PRINTER is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
#
# I2C support
#
# CONFIG_I2C is not set
#
# Mice
#
# CONFIG_BUSMOUSE is not set
CONFIG_MOUSE=y
CONFIG_PSMOUSE=y
# CONFIG_82C710_MOUSE is not set
# CONFIG_PC110_PAD is not set
# CONFIG_MK712_MOUSE is not set
#
# Joysticks
#
# CONFIG_INPUT_GAMEPORT is not set
# CONFIG_QIC02_TAPE is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_IPMI_PANIC_EVENT is not set
# CONFIG_IPMI_DEVICE_INTERFACE is not set
# CONFIG_IPMI_KCS is not set
# CONFIG_IPMI_WATCHDOG is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_SCx200 is not set
# CONFIG_SCx200_GPIO is not set
# CONFIG_AMD_RNG is not set
# CONFIG_INTEL_RNG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_AMD_PM768 is not set
CONFIG_NVRAM=m
# CONFIG_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
# CONFIG_AGP is not set
#
# Direct Rendering Manager (XFree86 DRI support)
#
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_OBMOUSE is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# File systems
#
CONFIG_QUOTA=y
# CONFIG_QFMT_V2 is not set
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_ADFS_FS is not set
# CONFIG_ADFS_FS_RW is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BEFS_DEBUG is not set
# CONFIG_BFS_FS is not set
CONFIG_EXT3_FS=y
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_UMSDOS_FS=m
CONFIG_VFAT_FS=m
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
CONFIG_TMPFS=y
CONFIG_RAMFS=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
# CONFIG_JFS_FS is not set
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_VXFS_FS is not set
CONFIG_NTFS_FS=m
# CONFIG_NTFS_RW is not set
CONFIG_HPFS_FS=m
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVFS_MOUNT is not set
# CONFIG_DEVFS_DEBUG is not set
CONFIG_DEVPTS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX4FS_RW is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_UDF_FS is not set
# CONFIG_UDF_RW is not set
# CONFIG_UFS_FS is not set
# CONFIG_UFS_FS_WRITE is not set
# CONFIG_XFS_FS is not set
# CONFIG_XFS_QUOTA is not set
# CONFIG_XFS_RT is not set
# CONFIG_XFS_TRACE is not set
# CONFIG_XFS_DEBUG is not set
#
# Network File Systems
#
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
# CONFIG_NFS_FS is not set
# CONFIG_NFS_V3 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_ROOT_NFS is not set
# CONFIG_NFSD is not set
# CONFIG_NFSD_V3 is not set
# CONFIG_NFSD_TCP is not set
# CONFIG_SUNRPC is not set
# CONFIG_LOCKD is not set
CONFIG_SMB_FS=m
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="cp437"
CONFIG_SMB_UNIX=y
# CONFIG_NCP_FS is not set
# CONFIG_NCPFS_PACKET_SIGNING is not set
# CONFIG_NCPFS_IOCTL_LOCKING is not set
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set
CONFIG_ZISOFS_FS=y
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_SMB_NLS=y
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=y
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y
#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
CONFIG_VIDEO_SELECT=y
#
# Sound
#
# CONFIG_SOUND is not set
#
# USB support
#
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
# CONFIG_USB_DEVICEFS is not set
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_EHCI_HCD is not set
CONFIG_USB_UHCI_ALT=y
# CONFIG_USB_OHCI is not set
# CONFIG_USB_SL811HS_ALT is not set
# CONFIG_USB_SL811HS is not set
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_MIDI is not set
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=m
# CONFIG_USB_HID is not set
# CONFIG_USB_HIDINPUT is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_DC2XX is not set
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_SCANNER is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_CATC is not set
# CONFIG_USB_CDCETHER is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_BRLVGER is not set
# CONFIG_USB_LCD is not set
#
# Support for USB gadgets
#
# CONFIG_USB_GADGET is not set
#
# Bluetooth support
#
# CONFIG_BLUEZ is not set
#
# Kernel hacking
#
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_HIGHMEM is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_IOVIRT is not set
CONFIG_MAGIC_SYSRQ=y
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_FRAME_POINTER is not set
CONFIG_LOG_BUF_SHIFT=0
#
# Cryptographic options
#
# CONFIG_CRYPTO is not set
#
# Library routines
#
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 2.4.32 Oops in scsi_dispatch_cmd
2005-12-07 22:52 ` Jan Oberländer
@ 2005-12-08 20:16 ` Willy TARREAU
0 siblings, 0 replies; 4+ messages in thread
From: Willy TARREAU @ 2005-12-08 20:16 UTC (permalink / raw)
To: Jan Oberländer; +Cc: linux-kernel
Hi,
On Wed, Dec 07, 2005 at 11:52:44PM +0100, Jan Oberländer wrote:
> On Wed, Dec 07, 2005 at 10:50:14PM +0100, Willy Tarreau wrote:
> > On Wed, Dec 07, 2005 at 10:37:47AM +0100, Jan Oberländer wrote:
> > > I've been receiving Oops repeatedly
> >
> > could you send your .config and gcc version please ? I've checked the
> > code and it's not easy to find what data is accessed in your oopses.
>
> I attached the .config.
>
> $ gcc -v
> Reading specs from /usr/lib/gcc-lib/i486-linux/3.3.5/specs
> Configured with: ../src/configure -v
> --enable-languages=c,c++,java,f77,pascal,objc,ada,treelang --prefix=/usr
> --mandir=/usr/share/man --infodir=/usr/share/info
> --with-gxx-include-dir=/usr/include/c++/3.3 --enable-shared
> --enable-__cxa_atexit --with-system-zlib --enable-nls
> --without-included-gettext --enable-clocale=gnu --enable-debug
> --enable-java-gc=boehm --enable-java-awt=xlib --enable-objc-gc
> i486-linux
> Thread model: posix
> gcc version 3.3.5 (Debian 1:3.3.5-13)
OK, thanks, I could reproduce the same code.
> > > The tar process is run from a backup scripts that mounts an IDE
> > > drive partition, writes a backup to it and unmounts it. It's always
> > > been the tar process behind this crash. Some system details:
> >
> > could you please also tell us what partition tar reads data from ?
> > I've understood that you have some disks on your adaptec card and some
> > software RAID, so if you could roughly explain the setup, it would be
> > great.
>
> The setup:
>
> /dev/hda on onboard IDE
> /dev/sd{a,b,c,d,e,f} on Adaptec
> md0 : active raid5 sdd1[2] sdc1[1] sdb1[0]
> md1 : active raid5 sdd2[2] sdc2[1] sdb2[0]
> md3 : active raid5 sdd3[2] sdc3[1] sdb3[0]
> md2 : active raid1 sdf1[1] sde1[0]
>
> The backup script roughly does the following:
> 1. mount hda
> 2. backup data from the md*,sd* devices to hda
> 3. umount hda
>
> As I said, the IDE drive was on an ATA RAID card at first, visible to
> the system as /dev/sdg. I changed this because of the tainted ATA RAID
> module, but I'm receiving the same oops either way.
>
> > It may be doable with a few more info. Please also confirm that your
> > System.map really matches your kernel (for the oops report).
>
> I double-checked.
Fine.
> Tell me if you need any further information.
I must say I'm a bit lost, I found this in drivers/scsi.c :
672 if (host->hostt->use_new_eh_code) {
673 scsi_add_timer(SCpnt, SCpnt->timeout_per_command, scsi_times_out);
674 } else {
675 scsi_add_timer(SCpnt, SCpnt->timeout_per_command,
676 scsi_old_times_out);
677 }
The oops you're reporting shows that eax==0 below :
mov 0x24(%edi),%eax
testb $0x4,0x67(%eax)
But at this point, eax=(struct Scsi_Host_Template *)host->hostt,
so host->hostt == NULL. The problem is that it is assigned only
once in drivers/scsi/host.c:scsi_register(), and it directly takes
the Scsi_Host_Template *tpnt passed as the first argument, which
is dereferenced many times before being assigned to host->hostt,
so it should have crashed far earlier and never reached this code.
So unless I'm missing something, I see two possibilities :
- a bug somewhere else corrupted the struct Scsi_Host and
put a NULL in hostt ;
- a hardware problem is having fun of you. I'd personnaly
check in this area first.
So I suggest that you run memtest on the whole system over night
if possible (at least several hours) to check memory. If you
cannot stop the system this long, then you might also exchange
all SIMMs with another system and check whether the problem
still happens.
What is possible too is a chipset problem or CPU overheating
during those intensive backup activity.
Good luck,
Willy
PS: please keep the whole CC list on LKML, as people generally
don't read the list all the day.
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2005-12-08 20:16 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-12-07 9:37 2.4.32 Oops in scsi_dispatch_cmd Jan Oberländer
2005-12-07 21:50 ` Willy Tarreau
2005-12-07 22:52 ` Jan Oberländer
2005-12-08 20:16 ` Willy TARREAU
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox