Re: [2.6.15] frequent "BUG: soft lockup detected on CPU#0" in IDE subsystem

[Folkert van Heusden <folkert@vanheusden.com>]

> >kernel: 2.6.15
> >system: 3.2GHz P4 hyperthreading, 1xIDE, 2GB ram
> >it seems to happen (altough I'm really not sure!) when the system is
> >under heavily load: > 8.0, while running sa-learn (the spamassassin
> >bayes training tool)
> 
> Lots of PIO transfers.. Is DMA not getting enabled on your drives?

According to this, DMA is enabled:

0 root@muur:/usr/src/linux-2.6.15/Documentation$ hdparm  -i /dev/hda

/dev/hda:

 Model=QUANTUM FIREBALLP AS20.5, FwRev=A2R.0600, SerialNo=692124031358
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=32256, SectSize=21298, ECCbytes=4
 BuffType=DualPortCache, BuffSize=1902kB, MaxMultSect=16, MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40132503
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1:

 * signifies the current active mode

Also, I run this at startup:
/usr/sbin/hdparm -c 3 -d 1 -X 69 -u 1 /dev/hda

Oh and at bootup it says it uses DMA for that drive:
[    0.431334] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[    0.431375] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    0.431440] ICH5: IDE controller at PCI slot 0000:00:1f.1
[    0.431482] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[    0.431524] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
[    0.431604] ICH5: chipset revision 2
[    0.431641] ICH5: not 100% native mode: will probe irqs later
[    0.431687]     ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
[    0.431799]     ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
[    0.431909] Probing IDE interface ide0...
[    0.749711] hda: QUANTUM FIREBALLP AS20.5, ATA DISK drive
[    1.479391] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[    1.479514] Probing IDE interface ide1...
[    2.268919] hdc: CREATIVEDVD6630E, ATAPI CD/DVD-ROM drive
[    2.638776] ide1 at 0x170-0x177,0x376 on irq 15
[    2.638996] hda: max request size: 128KiB
[    2.640382] hda: 40132503 sectors (20547 MB) w/1902KiB Cache, CHS=39813/16/63, UDMA(100)
[    2.640548] hda: cache flushes not supported
[    2.640625]  hda: hda1 hda2 hda3
[    2.645987] usbmon: debugfs is not available

A strange thing is, though, that I only get 5MB/s with hdparm -t.


Folkert van Heusden

-- 
Ever wonder what is out there? Any alien races? Then please support
the seti@home project: setiathome.ssl.berkeley.edu
----------------------------------------------------------------------
Phone: +31-6-41278122, PGP-key: 1F28D8AE, www.vanheusden.com