From: Sander <sander@humilis.net>
To: Andrew Morton <akpm@osdl.org>
Cc: linux-ide@vger.kernel.org, jgarzik@favonius.humilis.net, lkml@rtr.ca
Subject: sata_mv success on 2.6.16-rc6-mm2 (was: Re: 2.6.16-rc6-mm2)
Date: Sat, 18 Mar 2006 16:10:10 +0100 [thread overview]
Message-ID: <20060318151010.GA19568@favonius> (raw)
In-Reply-To: <20060318044056.350a2931.akpm@osdl.org>
Andrew Morton wrote (ao):
> ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.16-rc6/2.6.16-rc6-mm2/
Good news! This kernel lets me use eight Maxtor sata disks in raid5 over
nForce4 and Marvell MV88SX6081.
I do:
mdadm -C -l5 -n8 /dev/md0 /dev/sda1 /dev/sdb1 /dev/sdc1 \
/dev/sdd1 /dev/sde1 /dev/sdf1 /dev/sdg1 /dev/sdh1
mke2fs -j -m1 /dev/md0
mount -o data=writeback,nobh /dev/md0 /mnt
for i in `seq 10`
do dd if=/dev/zero of=bigfile.$i bs=1024k count=10000
done
md5sum bigfile.*
rm bigfile.*
and
for i in `seq 10`
do dd if=/dev/zero of=bigfile.$i bs=1024k count=10000 &
done
sleep 1200
md5sum bigfile.*
rm bigfile.*
and
for i in `seq 4`
do ( dd if=/dev/zero of=bigfile.$i bs=1024k count=10000 ; \
time md5sum bigfile.$i ) &
done
I experience no crash and no data corruption with these simple tests.
2.6.16-rc6 crashes with no output of the crash on netconsole (have to
find a screen to connect to the system).
2.6.16-rc3 crashes too:
http://www.ussg.iu.edu/hypermail/linux/kernel/0602.2/0360.html
I haven't tried 2.6.16-rc6-mm1.
With 2.6.16-rc6-mm2 I do get "BUG: warning ..." and "Call Trace: ..."
messages during boot (see dmesg below), which are not there with 2.6.16-rc6.
But that seems not to cause any problems.
I also see these appear during the tests:
[ 3584.499415] ata5: translated ATA stat/err 0xd0/00 to SCSI SK/ASC/ASCQ 0xb/47/00
[ 3584.499469] ata5: status=0xd0 { Busy }
[ 4430.676302] ata9: translated ATA stat/err 0xd0/00 to SCSI SK/ASC/ASCQ 0xb/47/00
[ 4430.676355] ata9: status=0xd0 { Busy }
But with no visible effect.
Thanks!
Kind regards, Sander
[ 82.078411] libata version 1.20 loaded.
[ 82.078449] sata_nv 0000:00:07.0: version 0.8
[ 82.078457] ACPI (acpi_bus-0216): Device 'SAT0' is not power manageable [20060210]
[ 82.078917] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 23
[ 82.078967] GSI 20 sharing vector 0xD1 and IRQ 20
[ 82.079015] ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 23 (level, high) -> IRQ 20
[ 82.079376] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 82.079446] ata1: SATA max UDMA/133 cmd 0x1440 ctl 0x1436 bmdma 0x1410 irq 20
[ 82.079520] ata2: SATA max UDMA/133 cmd 0x1438 ctl 0x1432 bmdma 0x1418 irq 20
[ 82.295014] ata1: SATA link up 3.0 Gbps (SStatus 123)
[ 82.494850] ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f69 84:4773 85:7c69 86:3e01 87:4763 88:407f
[ 82.494854] ata1: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
[ 82.496131] nv_sata: Primary device added
[ 82.496184] nv_sata: Primary device removed
[ 82.496228] nv_sata: Secondary device added
[ 82.496273] nv_sata: Secondary device removed
[ 82.524820] ata1: dev 0 configured for UDMA/133
[ 82.524865] scsi0 : sata_nv
[ 82.744454] ata2: SATA link down (SStatus 0)
[ 82.744500] scsi1 : sata_nv
[ 82.744637] Vendor: ATA Model: Maxtor 7H500F0 Rev: HA43
[ 82.745399] Type: Direct-Access ANSI SCSI revision: 05
[ 82.745582] ACPI (acpi_bus-0216): Device 'SAT1' is not power manageable [20060210]
[ 82.746058] ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 22
[ 82.746108] GSI 21 sharing vector 0xD9 and IRQ 21
[ 82.746157] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSI1] -> GSI 22 (level, high) -> IRQ 21
[ 82.746485] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 82.746551] ata3: SATA max UDMA/133 cmd 0x1458 ctl 0x144E bmdma 0x1420 irq 21
[ 82.746628] ata4: SATA max UDMA/133 cmd 0x1450 ctl 0x144A bmdma 0x1428 irq 21
[ 82.964178] ata3: SATA link down (SStatus 0)
[ 82.964222] scsi2 : sata_nv
[ 83.183902] ata4: SATA link down (SStatus 0)
[ 83.183946] scsi3 : sata_nv
[ 83.184069] sata_mv 0000:0a:03.0: version 0.6
[ 83.184129] GSI 22 sharing vector 0xE1 and IRQ 22
[ 83.184174] ACPI: PCI Interrupt 0000:0a:03.0[A] -> GSI 30 (level, low) -> IRQ 22
[ 83.187740] sata_mv 0000:0a:03.0: 32 slots 8 ports SCSI mode IRQ via INTx
[ 83.187857] ata5: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000222120 bmdma 0x0 irq 22
[ 83.187951] ata6: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000224120 bmdma 0x0 irq 22
[ 83.188042] ata7: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000226120 bmdma 0x0 irq 22
[ 83.188132] ata8: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000228120 bmdma 0x0 irq 22
[ 83.188222] ata9: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000232120 bmdma 0x0 irq 22
[ 83.188314] ata10: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000234120 bmdma 0x0 irq 22
[ 83.188404] ata11: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000236120 bmdma 0x0 irq 22
[ 83.188495] ata12: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000238120 bmdma 0x0 irq 22
[ 83.244314] BUG: warning at drivers/scsi/sata_mv.c:1896/__msleep()
[ 83.244362]
[ 83.244362] Call Trace: <IRQ> <ffffffff80408d00>{__mv_phy_reset+242}
[ 83.244509] <ffffffff804081ec>{mv_channel_reset+133} <ffffffff80409361>{mv_interrupt+565}
[ 83.244669] <ffffffff8023bf2c>{handle_IRQ_event+41} <ffffffff8023bffa>{__do_IRQ+155}
[ 83.244828] <ffffffff8020c13b>{do_IRQ+59} <ffffffff8020834c>{default_idle+0}
[ 83.244989] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eb96d>{thread_return+86}
[ 83.245172] <ffffffff80208379>{default_idle+45} <ffffffff80208406>{cpu_idle+98}
[ 83.245329] <ffffffff807c4018>{start_secondary+1224}
[ 86.569852] ata5: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c69 86:3e01 87:4063 88:007f
[ 86.569856] ata5: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 86.570840] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 86.570902]
[ 86.570903] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 86.571046] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 86.571208] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 86.571365] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eccd2>{__reacquire_kernel_lock+39}
[ 86.571552] <ffffffff804eb9bd>{thread_return+166} <ffffffff804ebfe5>{schedule_timeout+138}
[ 86.571713] <ffffffff8022a66c>{process_timeout+0} <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 86.571878] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 86.572042] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 86.575479] <ffffffff8023c4d1>{request_irq+130} <ffffffff804049f4>{ata_device_add+1163}
[ 86.575639] <ffffffff80409a41>{mv_init_one+1547} <ffffffff8036c8b2>{pci_device_probe+221}
[ 86.575799] <ffffffff803b999d>{driver_probe_device+82} <ffffffff803b9a52>{__driver_attach+0}
[ 86.575959] <ffffffff803b9aa8>{__driver_attach+86} <ffffffff803b8f5a>{bus_for_each_dev+67}
[ 86.576121] <ffffffff803b925a>{bus_add_driver+116} <ffffffff8036c918>{pci_bus_match+0}
[ 86.576279] <ffffffff8036c418>{__pci_register_driver+85} <ffffffff8020720c>{init+455}
[ 86.576438] <ffffffff8020a6b6>{child_rip+8} <ffffffff80207045>{init+0}
[ 86.576582] <ffffffff8020a6ae>{child_rip+0}
[ 86.599812] ata5: dev 0 configured for UDMA/133
[ 86.599856] scsi4 : sata_mv
[ 89.975572] ata6: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e21 87:4663 88:007f
[ 89.975576] ata6: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 89.976575] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 89.976637]
[ 89.976638] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 89.976780] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 89.976943] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 89.977100] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eb96d>{thread_return+86}
[ 89.977287] <ffffffff804ebfe5>{schedule_timeout+138} <ffffffff8022a66c>{process_timeout+0}
[ 89.977450] <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 89.977546] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 89.977710] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 89.977871] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 89.978032] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 89.978195] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 89.978355] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 89.978514] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 89.978676] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 89.978832] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 90.005534] ata6: dev 0 configured for UDMA/133
[ 90.005579] scsi5 : sata_mv
[ 93.381295] ata7: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c69 86:3e01 87:4063 88:007f
[ 93.381299] ata7: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 93.382285] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 93.382347]
[ 93.382348] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 93.382491] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 93.382652] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 93.382810] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804ecb0e>{_spin_lock_irqsave+2}
[ 93.382996] <ffffffff8022a1d9>{lock_timer_base+27} <ffffffff8022addd>{try_to_del_timer_sync+22}
[ 93.383157] <ffffffff8022ae2c>{del_timer_sync+12} <ffffffff804ebfed>{schedule_timeout+146}
[ 93.383317] <ffffffff8022a66c>{process_timeout+0} <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 93.383480] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 93.383642] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 93.383803] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 93.383965] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 93.384125] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 93.384285] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 93.384446] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 93.384606] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 93.384762] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 93.411257] ata7: dev 0 configured for UDMA/133
[ 93.411304] scsi6 : sata_mv
[ 96.787019] ata8: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c69 86:3e01 87:4063 88:007f
[ 96.787023] ata8: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 96.788019] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 96.788081]
[ 96.788081] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 96.788224] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 96.788385] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 96.788541] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff8022a1c4>{lock_timer_base+6}
[ 96.788726] <ffffffff8022addd>{try_to_del_timer_sync+22} <ffffffff8022ae2c>{del_timer_sync+12}
[ 96.788886] <ffffffff804ebfed>{schedule_timeout+146} <ffffffff8022a66c>{process_timeout+0}
[ 96.789046] <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 96.789142] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff804ecb5d>{_spin_unlock_irqrestore+8}
[ 96.789302] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 96.789462] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 96.789625] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 96.789787] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 96.789947] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 96.790110] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 96.790270] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 96.790426] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 96.816981] ata8: dev 0 configured for UDMA/133
[ 96.817025] scsi7 : sata_mv
[ 100.192743] ata9: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e21 87:4663 88:007f
[ 100.192747] ata9: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 100.193757] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 100.193819]
[ 100.193820] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 100.193963] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 100.194124] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 100.194283] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eb973>{thread_return+92}
[ 100.194469] <ffffffff804ebfe5>{schedule_timeout+138} <ffffffff8022a66c>{process_timeout+0}
[ 100.194629] <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 100.194724] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 100.194887] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 100.195048] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 100.195208] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 100.195372] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 100.195531] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 100.195690] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 100.195853] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 100.196010] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 100.222704] ata9: dev 0 configured for UDMA/133
[ 100.222749] scsi8 : sata_mv
[ 103.598467] ata10: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c69 86:3e01 87:4063 88:007f
[ 103.598471] ata10: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 103.599467] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 103.599530]
[ 103.599531] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 103.599674] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 103.599834] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 103.599992] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eccd2>{__reacquire_kernel_lock+39}
[ 103.600179] <ffffffff804eb9bd>{thread_return+166} <ffffffff804ebfe5>{schedule_timeout+138}
[ 103.600340] <ffffffff8022a66c>{process_timeout+0} <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 103.600502] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 103.600666] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 103.600826] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 103.600986] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 103.601152] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 103.601314] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 103.604759] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 103.604919] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 103.605075] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 103.628428] ata10: dev 0 configured for UDMA/133
[ 103.628473] scsi9 : sata_mv
[ 106.994203] ata11: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e21 87:4663 88:007f
[ 106.994207] ata11: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 106.995198] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 106.995261]
[ 106.995262] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 106.995405] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 106.995565] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 106.995722] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eb917>{thread_return+0}
[ 106.995907] <ffffffff804eb9bd>{thread_return+166} <ffffffff804eb9ec>{thread_return+213}
[ 106.996069] <ffffffff804ebfe5>{schedule_timeout+138} <ffffffff8022a66c>{process_timeout+0}
[ 106.996228] <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 106.996325] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 106.996486] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 106.996646] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 106.996808] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 106.996969] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 106.997129] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 106.997291] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 106.997453] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 106.997611] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 107.024165] ata11: dev 0 configured for UDMA/133
[ 107.024210] scsi10 : sata_mv
[ 107.073907] ata12: no device found (phy stat 00000000)
[ 107.073953] scsi11 : sata_mv
[ 107.074082] Vendor: ATA Model: Maxtor 6B300S0 Rev: BANC
[ 107.074841] Type: Direct-Access ANSI SCSI revision: 05
[ 107.075044] Vendor: ATA Model: Maxtor 6L300S0 Rev: BACE
[ 107.075798] Type: Direct-Access ANSI SCSI revision: 05
[ 107.075994] Vendor: ATA Model: Maxtor 6B300S0 Rev: BANC
[ 107.076749] Type: Direct-Access ANSI SCSI revision: 05
[ 107.076944] Vendor: ATA Model: Maxtor 6B300S0 Rev: BANC
[ 107.077701] Type: Direct-Access ANSI SCSI revision: 05
[ 107.077900] Vendor: ATA Model: Maxtor 6L300S0 Rev: BACE
[ 107.078653] Type: Direct-Access ANSI SCSI revision: 05
[ 107.078857] Vendor: ATA Model: Maxtor 6B300S0 Rev: BANC
[ 107.079610] Type: Direct-Access ANSI SCSI revision: 05
[ 107.079806] Vendor: ATA Model: Maxtor 6L300S0 Rev: BACE
[ 107.080559] Type: Direct-Access ANSI SCSI revision: 05
[ 107.080785] SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
[ 107.080848] sda: Write Protect is off
[ 107.080893] sda: Mode Sense: 00 3a 00 00
[ 107.080905] SCSI device sda: drive cache: write back
[ 107.081014] SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
[ 107.081069] sda: Write Protect is off
[ 107.081112] sda: Mode Sense: 00 3a 00 00
[ 107.081124] SCSI device sda: drive cache: write back
[ 107.081170] sda: sda1
[ 107.099237] sd 0:0:0:0: Attached scsi disk sda
etc, etc.
--
Humilis IT Services and Solutions
http://www.humilis.net
next prev parent reply other threads:[~2006-03-18 15:34 UTC|newest]
Thread overview: 97+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-03-18 12:40 2.6.16-rc6-mm2 Andrew Morton
2006-03-18 15:10 ` Sander [this message]
2006-03-18 17:25 ` 2.6.16-rc6-mm2: new RDMA CM EXPORT_SYMBOL's Adrian Bunk
2006-03-19 1:44 ` Tom Tucker
2006-03-19 1:57 ` Lee Revell
2006-03-18 18:45 ` [-mm patch] drivers/edac/e752x_edac.c: make sysbus_message static Adrian Bunk
2006-03-18 18:45 ` [-mm patch] drivers/scsi/aic7xxx/aic79xx_core.c: make ahd_match_scb() static Adrian Bunk
2006-03-18 18:45 ` [-mm patch] nfs4proc.c: make _nfs4_proc_setclientid_confirm() static Adrian Bunk
2006-03-18 18:45 ` [-mm patch] net/core/scm.c: make scm_detach_fds() static Adrian Bunk
2006-03-18 20:21 ` 2.6.16-rc6-mm2 Rafael J. Wysocki
2006-03-18 20:54 ` 2.6.16-rc6-mm2 Andrew Morton
2006-03-18 21:24 ` 2.6.16-rc6-mm2 Rafael J. Wysocki
2006-03-18 21:25 ` Emulex IP over FC support shogunx
2006-03-19 23:03 ` 2.6.16-rc6-mm2 - BUG when flushing a ramdisk Neil Brown
2006-03-19 1:09 ` 2.6.16-rc6-mm2 uninitialized online_policy_cpus.bits[0] Con Kolivas
2006-03-19 1:29 ` Con Kolivas
2006-03-19 1:35 ` Andrew Morton
2006-03-19 2:37 ` Con Kolivas
2006-03-19 6:13 ` Venkatesh Pallipadi
2006-03-20 3:26 ` New Areca driver in 2.6.16-rc6-mm2 Dax Kelson
2006-03-21 23:49 ` Chris Caputo
2006-03-22 3:37 ` Matti Aarnio
2006-03-22 3:56 ` Randy.Dunlap
2006-03-22 3:56 ` Al Viro
2006-03-22 4:41 ` erich
2006-03-20 13:02 ` RAID5 grow success (was: Re: 2.6.16-rc6-mm2) Sander
2006-03-20 13:33 ` Some sata_mv error messages " Sander
2006-03-21 1:02 ` Some sata_mv error messages Jeff Garzik
2006-03-21 2:25 ` Dave Jones
2006-03-21 2:35 ` Jeff Garzik
2006-03-21 16:06 ` Peter Jones
2006-03-21 4:48 ` Mark Lord
2006-03-21 7:28 ` Sander
2006-03-21 19:33 ` Denis Leroy
2006-03-21 19:37 ` Jeff Garzik
2006-03-21 19:42 ` Mark Lord
2006-03-21 7:26 ` Sander
2006-03-21 20:27 ` 2.6.16-rc6-mm2: reiser4 BUG when unmounting fs Laurent Riffard
2006-03-21 20:38 ` Laurent Riffard
2006-03-22 7:43 ` Vladimir V. Saveliev
2006-03-22 18:38 ` Laurent Riffard
2006-03-23 17:32 ` Alexander Gran
2006-03-21 22:54 ` 2.6.16-rc6-mm2: Why is CONFIG_MIGRATION available for everyone? Adrian Bunk
2006-03-21 22:57 ` Christoph Lameter
2006-03-21 23:40 ` Christoph Lameter
2006-03-22 8:41 ` 2.6.16-rc6-mm2 J.A. Magallon
2006-03-22 8:48 ` 2.6.16-rc6-mm2 Andrew Morton
2006-03-22 10:40 ` [2.6 patch] kernel/time.c: remove unused pps_* variables Adrian Bunk
-- strict thread matches above, loose matches on Subject: below --
2006-02-01 20:03 [PATCH 0/5] Infiniband: connection abstraction Sean Hefty
2006-02-01 20:07 ` [PATCH 1/5] " Sean Hefty
2006-02-01 20:10 ` [PATCH 2/5] " Sean Hefty
2006-02-01 20:15 ` [PATCH 3/5] " Sean Hefty
2006-03-03 21:14 ` [PATCH 3/5] export of ip_dev_find as part of Infiniband " Sean Hefty
2006-02-01 20:18 ` [PATCH 4/5] Infiniband: " Sean Hefty
2006-02-01 20:19 ` [PATCH 5/5] " Sean Hefty
2006-03-03 21:13 ` [PATCH 0/5] " Sean Hefty
2006-03-03 22:53 ` [openib-general] " Roland Dreier
2006-03-06 18:59 ` [PATCH 1/6] IB: common handling for marshalling parameters to/from userspace Sean Hefty
2006-03-19 1:19 ` 2.6.16-rc6-mm2: new RDMA CM EXPORT_SYMBOL's Andrew Morton
2006-03-19 4:11 ` Matthew Frost
2006-03-20 18:32 ` [openib-general] " Sean Hefty
2006-03-20 18:47 ` Arjan van de Ven
2006-03-20 18:47 ` Roland Dreier
2006-03-20 19:18 ` [openib-general] " Sean Hefty
2006-03-06 19:04 ` [PATCH 2/6] IB: match connection requests based on private data Sean Hefty
2006-03-06 22:05 ` [openib-general] " Sean Hefty
2006-03-06 23:29 ` [PATCH 2/6 v2] " Sean Hefty
2006-03-06 19:07 ` [PATCH 3/6] net/IB: export ip_dev_find Sean Hefty
2006-03-06 21:31 ` Roland Dreier
2006-03-06 21:42 ` David S. Miller
2006-03-06 19:10 ` [PATCH 4/6] IB: address translation to map IP to IB addresses (GIDs) Sean Hefty
2006-03-06 23:31 ` [PATCH 4/6 v2] IB: address translation to map IP toIB " Sean Hefty
2006-03-11 1:14 ` Roland Dreier
2006-03-11 6:10 ` Sean Hefty
2006-03-21 20:57 ` Roland Dreier
2006-03-21 21:08 ` [openib-general] " Sean Hefty
2006-03-21 22:39 ` Roland Dreier
2006-03-06 19:18 ` [PATCH 5/6] IB: IP address based RDMA connection manager Sean Hefty
2006-03-06 19:21 ` [PATCH 6/6] IB: userspace support for " Sean Hefty
2006-03-06 21:33 ` Roland Dreier
2006-03-06 21:42 ` [openib-general] " Sean Hefty
2006-03-06 21:58 ` Roland Dreier
2006-03-06 22:28 ` David S. Miller
2006-03-06 22:32 ` Roland Dreier
2006-03-06 22:39 ` David S. Miller
2006-03-06 22:41 ` Roland Dreier
2006-03-06 22:50 ` David S. Miller
2006-03-06 23:40 ` Roland Dreier
2006-03-07 0:05 ` Bryan O'Sullivan
2006-03-07 0:10 ` Roland Dreier
2006-03-07 0:26 ` David S. Miller
2006-03-06 21:35 ` Roland Dreier
2006-03-06 21:43 ` [openib-general] " Sean Hefty
2006-03-06 23:41 ` [PATCH 6/6 v2] " Sean Hefty
2006-03-22 1:40 ` Roland Dreier
2006-03-22 8:30 ` Michael S. Tsirkin
2006-03-22 15:18 ` Roland Dreier
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060318151010.GA19568@favonius \
--to=sander@humilis.net \
--cc=akpm@osdl.org \
--cc=jgarzik@favonius.humilis.net \
--cc=linux-ide@vger.kernel.org \
--cc=lkml@rtr.ca \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox