From: Greg KH <greg@kroah.com>
To: Bernhard Rosenkraenzer <bero@arklinux.org>,
linux-usb-devel@lists.sourceforge.net
Cc: linux-kernel@vger.kernel.org
Subject: Re: USB 2.0 CF card reader gets reset+offlined immediately with 2.6.16
Date: Wed, 5 Apr 2006 17:59:10 -0700 [thread overview]
Message-ID: <20060406005910.GA18567@kroah.com> (raw)
In-Reply-To: <200604060012.04300.bero@arklinux.org>
On Thu, Apr 06, 2006 at 12:12:04AM +0200, Bernhard Rosenkraenzer wrote:
> Attempting to use a USB 2.0 CF card reader in 2.6.16 and 2.6.16-mm2 (known to
> work back in 2.4 days, unused since) results in this:
Can you enable CONFIG_USB_STORAGE_DEBUG and send the kernel log file to
the linux-usb-devel mailing list so the people there can help you out?
thanks,
greg k-h
<linux-usb-devel people, here's the original log>
> usb 1-6: new high speed USB device using ehci_hcd and address 2
> usb 1-6: new device found, idVendor=0dda, idProduct=2005
> usb 1-6: new device strings: Mfr=3, Product=4, SerialNumber=5
> usb 1-6: Product: Card Reader
> usb 1-6: Manufacturer: Hama
> usb 1-6: SerialNumber: 000000000013
> usb 1-6: configuration #1 chosen from 1 choice
> usbcore: registered new driver libusual
> Initializing USB Mass Storage driver...
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usb-storage: device found at 2
> usb-storage: waiting for device to settle before scanning
> Vendor: Hama Model: CF Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:0: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:0: rejecting I/O to offline device
> sd 0:0:0:0: rejecting I/O to offline device
> sd 0:0:0:0: rejecting I/O to offline device
> sda : READ CAPACITY failed.
> sda : status=0, message=00, host=1, driver=00
> sda : sense not available.
> sd 0:0:0:0: rejecting I/O to offline device
> sda: Write Protect is off
> sda: Mode Sense: 00 00 00 00
> sda: assuming drive cache: write through
> sd 0:0:0:0: Attached scsi removable disk sda
> Vendor: Hama Model: SM Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:1: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:1: rejecting I/O to offline device
> sd 0:0:0:1: rejecting I/O to offline device
> sd 0:0:0:1: rejecting I/O to offline device
> sdb : READ CAPACITY failed.
> sdb : status=0, message=00, host=1, driver=00
> sdb : sense not available.
> sd 0:0:0:1: rejecting I/O to offline device
> sdb: Write Protect is off
> sdb: Mode Sense: 00 00 00 00
> sdb: assuming drive cache: write through
> sd 0:0:0:1: Attached scsi removable disk sdb
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> Vendor: Hama Model: SD Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:2: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:2: rejecting I/O to offline device
> sd 0:0:0:2: rejecting I/O to offline device
> sd 0:0:0:2: rejecting I/O to offline device
> sdc : READ CAPACITY failed.
> sdc : status=0, message=00, host=1, driver=00
> sdc : sense not available.
> sd 0:0:0:2: rejecting I/O to offline device
> sdc: Write Protect is off
> sdc: Mode Sense: 00 00 00 00
> sdc: assuming drive cache: write through
> sd 0:0:0:2: Attached scsi removable disk sdc
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> Vendor: Hama Model: MS Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:3: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:3: rejecting I/O to offline device
> sd 0:0:0:3: rejecting I/O to offline device
> sd 0:0:0:3: rejecting I/O to offline device
> sdd : READ CAPACITY failed.
> sdd : status=0, message=00, host=1, driver=00
> sdd : sense not available.
> sd 0:0:0:3: rejecting I/O to offline device
> sdd: Write Protect is off
> sdd: Mode Sense: 00 00 00 00
> sdd: assuming drive cache: write through
> sd 0:0:0:3: Attached scsi removable disk sdd
> usb-storage: device scan complete
>
>
> Any attempt to access the devices afterwards results in ENXIO (but
> the /sys/block entries for sda to sdd remain there).
prev parent reply other threads:[~2006-04-06 0:59 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-04-05 22:12 USB 2.0 CF card reader gets reset+offlined immediately with 2.6.16 Bernhard Rosenkraenzer
2006-04-06 0:59 ` Greg KH [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060406005910.GA18567@kroah.com \
--to=greg@kroah.com \
--cc=bero@arklinux.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb-devel@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox