[2.6.17.11] strange pcie errors/warnings on Abit KN9-SLI mainboard

public inbox for linux-kernel@vger.kernel.org
 help / color / mirror / Atom feed

* [2.6.17.11] strange pcie errors/warnings on Abit KN9-SLI mainboard
@ 2006-08-28  5:55 Jan De Luyck
  2006-08-28  8:14 ` Arjan van de Ven
  0 siblings, 1 reply; 4+ messages in thread
From: Jan De Luyck @ 2006-08-28  5:55 UTC (permalink / raw)
  To: linux-kernel

Hello,

(running 2.6.17.11 vanilla on Debian SID)

I recently acquired a new pc, with an ABIT KN9-SLI mainboard, using an AMD64x2 
AM2 processor.

System boots fine, but I have some messages/errors in the dmesg that I'm worried 
about. Googling around for them didn't really show up much.

First:

Aug 27 15:35:04 whocares kernel: PCI-DMA: Disabling IOMMU.

IOMMU is (as far as I can see) enabled:
whocares:/var/log# cat /usr/src/build/linux-2.6/.config | grep IOMMU
CONFIG_GART_IOMMU=y

I can't really determine if this is normal. According to the code it seems that 
this is disabled by default when you don't have AGP? (I'm not a kernel-coder, so 
I may be very wrong on this)

Second:

Aug 27 15:35:04 whocares kernel: PCI: Setting latency timer of device 0000:00:0a.0 to 64
Aug 27 15:35:04 whocares kernel: pcie_portdrv_probe->Dev[0376:10de] has invalid IRQ. Check vendor BIOS
Aug 27 15:35:04 whocares kernel: assign_interrupt_mode Found MSI capability
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0a.0:pcie00]
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0a.0:pcie03]
Aug 27 15:35:04 whocares kernel: PCI: Setting latency timer of device 0000:00:0b.0 to 64
Aug 27 15:35:04 whocares kernel: pcie_portdrv_probe->Dev[0374:10de] has invalid IRQ. Check vendor BIOS
Aug 27 15:35:04 whocares kernel: assign_interrupt_mode Found MSI capability
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0b.0:pcie00]
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0b.0:pcie03]
Aug 27 15:35:04 whocares kernel: PCI: Setting latency timer of device 0000:00:0c.0 to 64
Aug 27 15:35:04 whocares kernel: pcie_portdrv_probe->Dev[0374:10de] has invalid IRQ. Check vendor BIOS
Aug 27 15:35:04 whocares kernel: assign_interrupt_mode Found MSI capability
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0c.0:pcie00]
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0c.0:pcie03]
Aug 27 15:35:04 whocares kernel: PCI: Setting latency timer of device 0000:00:0d.0 to 64
Aug 27 15:35:04 whocares kernel: pcie_portdrv_probe->Dev[0378:10de] has invalid IRQ. Check vendor BIOS
Aug 27 15:35:04 whocares kernel: assign_interrupt_mode Found MSI capability
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0d.0:pcie00]
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0d.0:pcie03]
Aug 27 15:35:04 whocares kernel: PCI: Setting latency timer of device 0000:00:0e.0 to 64
Aug 27 15:35:04 whocares kernel: pcie_portdrv_probe->Dev[0375:10de] has invalid IRQ. Check vendor BIOS
Aug 27 15:35:04 whocares kernel: assign_interrupt_mode Found MSI capability
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0e.0:pcie00]
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0e.0:pcie03]
Aug 27 15:35:04 whocares kernel: PCI: Setting latency timer of device 0000:00:0f.0 to 64
Aug 27 15:35:04 whocares kernel: pcie_portdrv_probe->Dev[0377:10de] has invalid IRQ. Check vendor BIOS
Aug 27 15:35:04 whocares kernel: assign_interrupt_mode Found MSI capability
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0f.0:pcie00]
Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0f.0:pcie03]

Any ideas what might be wrong? If anything is wrong, that is.

Thanks!

Jan
-- 
Q:	How do you keep a moron in suspense?

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [2.6.17.11] strange pcie errors/warnings on Abit KN9-SLI mainboard
  2006-08-28  5:55 [2.6.17.11] strange pcie errors/warnings on Abit KN9-SLI mainboard Jan De Luyck
@ 2006-08-28  8:14 ` Arjan van de Ven
  0 siblings, 0 replies; 4+ messages in thread
From: Arjan van de Ven @ 2006-08-28  8:14 UTC (permalink / raw)
  To: Jan De Luyck; +Cc: linux-kernel

On Mon, 2006-08-28 at 07:55 +0200, Jan De Luyck wrote:
> Hello,
> 
> (running 2.6.17.11 vanilla on Debian SID)
> 
> I recently acquired a new pc, with an ABIT KN9-SLI mainboard, using an AMD64x2 
> AM2 processor.
> 
> System boots fine, but I have some messages/errors in the dmesg that I'm worried 
> about. Googling around for them didn't really show up much.
> 
> First:
> 
> Aug 27 15:35:04 whocares kernel: PCI-DMA: Disabling IOMMU.
> 
> IOMMU is (as far as I can see) enabled:
> whocares:/var/log# cat /usr/src/build/linux-2.6/.config | grep IOMMU
> CONFIG_GART_IOMMU=y
> 
> I can't really determine if this is normal. According to the code it seems that 
> this is disabled by default when you don't have AGP? (I'm not a kernel-coder, so 
> I may be very wrong on this)

Hi,

unless you have >= 4Gb of ram you don't need an IOMMU (in fact using it
would only cause extra overhead)... so the kernel will not use it in
that case.

Greetings,
   Arjan van de Ven


^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [2.6.17.11] strange pcie errors/warnings on Abit KN9-SLI mainboard
@ 2006-08-28  9:50 Chuck Ebbert
  2006-08-29  5:19 ` Jan De Luyck
  0 siblings, 1 reply; 4+ messages in thread
From: Chuck Ebbert @ 2006-08-28  9:50 UTC (permalink / raw)
  To: Jan De Luyck; +Cc: linux-kernel

In-Reply-To: <200608280755.56015.ml_linuxkernel_20060528@kcore.org>

On Mon, 28 Aug 2006 07:55:55 +0200, Jan De Luyck wrote:

> Aug 27 15:35:04 whocares kernel: PCI: Setting latency timer of device 0000:00:0a.0 to 64
> Aug 27 15:35:04 whocares kernel: pcie_portdrv_probe->Dev[0376:10de] has invalid IRQ. Check vendor BIOS
> Aug 27 15:35:04 whocares kernel: assign_interrupt_mode Found MSI capability
> Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0a.0:pcie00]
> Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0a.0:pcie03]

Any other messages?  In addition to the above, I get:

PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:04.0
PCI: Cannot allocate resource region 9 of bridge 0000:00:04.0
PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0

for my two pcie bridges.

Also please post 'lspci -v' output for one of the problem devices.

-- 
Chuck


^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [2.6.17.11] strange pcie errors/warnings on Abit KN9-SLI mainboard
  2006-08-28  9:50 Chuck Ebbert
@ 2006-08-29  5:19 ` Jan De Luyck
  0 siblings, 0 replies; 4+ messages in thread
From: Jan De Luyck @ 2006-08-29  5:19 UTC (permalink / raw)
  To: Chuck Ebbert; +Cc: linux-kernel

[-- Attachment #1: Type: text/plain, Size: 12636 bytes --]

On Monday 28 August 2006 11:50, Chuck Ebbert wrote:
> In-Reply-To: <200608280755.56015.ml_linuxkernel_20060528@kcore.org>
>
> On Mon, 28 Aug 2006 07:55:55 +0200, Jan De Luyck wrote:
> > Aug 27 15:35:04 whocares kernel: PCI: Setting latency timer of device 0000:00:0a.0 to 64 
> > Aug 27 15:35:04 whocares kernel: pcie_portdrv_probe->Dev[0376:10de] has invalid IRQ. Check vendor BIOS 
> > Aug 27 15:35:04 whocares kernel: assign_interrupt_mode Found MSI capability
> > Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0a.0:pcie00] 
> > Aug 27 15:35:04 whocares kernel: Allocate Port Service[0000:00:0a.0:pcie03]
>
> Any other messages?  In addition to the above, I get:
>
> PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
> PCI: Cannot allocate resource region 8 of bridge 0000:00:04.0
> PCI: Cannot allocate resource region 9 of bridge 0000:00:04.0
> PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0
> PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0

Nope, I'm not seeing those.

I have the messages for all my pcie bridges. Here's the lspci output:

00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: fa000000-fcffffff
	Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
	Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
		Address: 00000000fee00000  Data: 40b9
	Capabilities: [60] HyperTransport: MSI Mapping
	Capabilities: [80] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <512ns, L1 <4us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
		Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
		Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 5
		Link: Latency L0s <512ns, L1 <4us
		Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
		Link: Speed 2.5Gb/s, Width x8
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
		Slot: Number 0, PowerLimit 0.000000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
		Slot: AttnInd Off, PwrInd On, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-
	Capabilities: [100] Virtual Channel

00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	I/O behind bridge: 00008000-00008fff
	Memory behind bridge: fdc00000-fdcfffff
	Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
	Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
		Address: 00000000fee00000  Data: 40c1
	Capabilities: [60] HyperTransport: MSI Mapping
	Capabilities: [80] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <512ns, L1 <4us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
		Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
		Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
		Link: Latency L0s <512ns, L1 <4us
		Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
		Link: Speed 2.5Gb/s, Width x4
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
		Slot: Number 0, PowerLimit 0.000000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
		Slot: AttnInd Off, PwrInd On, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-
	Capabilities: [100] Virtual Channel

00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
	I/O behind bridge: 00007000-00007fff
	Memory behind bridge: fda00000-fdafffff
	Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
	Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
		Address: 00000000fee00000  Data: 40c9
	Capabilities: [60] HyperTransport: MSI Mapping
	Capabilities: [80] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <512ns, L1 <4us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
		Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
		Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
		Link: Latency L0s <512ns, L1 <4us
		Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
		Link: Speed 2.5Gb/s, Width x4
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
		Slot: Number 0, PowerLimit 0.000000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
		Slot: AttnInd Off, PwrInd On, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-
	Capabilities: [100] Virtual Channel

00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
	I/O behind bridge: 00006000-00006fff
	Memory behind bridge: fd800000-fd8fffff
	Prefetchable memory behind bridge: 00000000fd700000-00000000fd7fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
	Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
		Address: 00000000fee00000  Data: 40d1
	Capabilities: [60] HyperTransport: MSI Mapping
	Capabilities: [80] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <512ns, L1 <4us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
		Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
		Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
		Link: Latency L0s <512ns, L1 <4us
		Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
		Link: Speed 2.5Gb/s, Width x4
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
		Slot: Number 0, PowerLimit 0.000000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
		Slot: AttnInd Off, PwrInd On, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-
	Capabilities: [100] Virtual Channel

00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
	I/O behind bridge: 00005000-00005fff
	Memory behind bridge: fd600000-fd6fffff
	Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
	Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
		Address: 00000000fee00000  Data: 40d9
	Capabilities: [60] HyperTransport: MSI Mapping
	Capabilities: [80] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <512ns, L1 <4us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
		Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
		Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
		Link: Latency L0s <512ns, L1 <4us
		Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
		Link: Speed 2.5Gb/s, Width x8
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
		Slot: Number 0, PowerLimit 0.000000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
		Slot: AttnInd Off, PwrInd On, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-
	Capabilities: [100] Virtual Channel

00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
	I/O behind bridge: 00004000-00004fff
	Memory behind bridge: f7000000-f9ffffff
	Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
	Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
		Address: 00000000fee00000  Data: 40e1
	Capabilities: [60] HyperTransport: MSI Mapping
	Capabilities: [80] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <512ns, L1 <4us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
		Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
		Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
		Link: Latency L0s <512ns, L1 <4us
		Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
		Link: Speed 2.5Gb/s, Width x16
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
		Slot: Number 0, PowerLimit 0.000000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
		Slot: AttnInd Off, PwrInd On, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-
	Capabilities: [100] Virtual Channel

Full dmesg and lspci attached.

Kind regards,

Jan
-- 
f u cn rd ths, u cn gt a gd jb n cmptr prgrmmng.

[-- Attachment #2: dmesg.gz --]
[-- Type: application/x-gzip, Size: 4522 bytes --]

[-- Attachment #3: lspci.gz --]
[-- Type: application/x-gzip, Size: 3347 bytes --]

^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, other threads:[~2006-08-29  5:19 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2006-08-28  5:55 [2.6.17.11] strange pcie errors/warnings on Abit KN9-SLI mainboard Jan De Luyck
2006-08-28  8:14 ` Arjan van de Ven
  -- strict thread matches above, loose matches on Subject: below --
2006-08-28  9:50 Chuck Ebbert
2006-08-29  5:19 ` Jan De Luyck

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox