* PCI bridge missing
@ 2006-09-28 21:24 Luke-Jr
2006-09-28 21:39 ` Mark Knecht
` (2 more replies)
0 siblings, 3 replies; 10+ messages in thread
From: Luke-Jr @ 2006-09-28 21:24 UTC (permalink / raw)
To: linux-kernel
This applies to Debian sarge kernels kernel-image-2.4.27-2-686, 2.6.8-3-686,
2.6.16-2-686, and 2.6.17-2-686...
I am trying to setup a Dell Optiplex GX1p system, which has a daughterboard
PCI bridge for its PCI and ISA slots:
00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03)
However, this bridge is completely ignored and unseen by Linux. It does not
show up in lspci or dmesg (as far as I can tell) at all. The daughterboard is
plugged in, and the PCI cards on it are powered.
How could I go about troubleshooting the problem? Has anyone experienced
something like this before?
Thanks,
Luke-Jr
P.S. Please CC me if possible.
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: PCI bridge missing
2006-09-28 21:24 PCI bridge missing Luke-Jr
@ 2006-09-28 21:39 ` Mark Knecht
2006-09-28 21:52 ` Mark Felder
2006-09-28 23:14 ` Alan Cox
2 siblings, 0 replies; 10+ messages in thread
From: Mark Knecht @ 2006-09-28 21:39 UTC (permalink / raw)
To: Luke-Jr; +Cc: linux-kernel
On 9/28/06, Luke-Jr <luke@dashjr.org> wrote:
> This applies to Debian sarge kernels kernel-image-2.4.27-2-686, 2.6.8-3-686,
> 2.6.16-2-686, and 2.6.17-2-686...
> I am trying to setup a Dell Optiplex GX1p system, which has a daughterboard
> PCI bridge for its PCI and ISA slots:
> 00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03)
>
> However, this bridge is completely ignored and unseen by Linux. It does not
> show up in lspci or dmesg (as far as I can tell) at all. The daughterboard is
> plugged in, and the PCI cards on it are powered.
>
> How could I go about troubleshooting the problem? Has anyone experienced
> something like this before?
>
> Thanks,
>
> Luke-Jr
>
Hi Luke,
I have one machine with a PCI Bridge problem. This machine has PCI
TV cards behind a bridge. The cards are never recognized on a warm
boot but they are always found when the machine is cold booted. Go
figure.
Anyway, maybe you haven't cold booted the machine and could try that?
- Mark
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PCI bridge missing
2006-09-28 21:24 PCI bridge missing Luke-Jr
2006-09-28 21:39 ` Mark Knecht
@ 2006-09-28 21:52 ` Mark Felder
2006-09-28 23:14 ` Alan Cox
2 siblings, 0 replies; 10+ messages in thread
From: Mark Felder @ 2006-09-28 21:52 UTC (permalink / raw)
To: Luke-Jr; +Cc: linux-kernel
I have Dell Optiplex GX1's at the school district I'm covering at. I can test some stuff out with various live CDs if that would help.
Mark
On Thu, 28 Sep 2006 16:24:15 -0500
Luke-Jr <luke@dashjr.org> wrote:
> This applies to Debian sarge kernels kernel-image-2.4.27-2-686, 2.6.8-3-686,
> 2.6.16-2-686, and 2.6.17-2-686...
> I am trying to setup a Dell Optiplex GX1p system, which has a daughterboard
> PCI bridge for its PCI and ISA slots:
> 00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03)
>
> However, this bridge is completely ignored and unseen by Linux. It does not
> show up in lspci or dmesg (as far as I can tell) at all. The daughterboard is
> plugged in, and the PCI cards on it are powered.
>
> How could I go about troubleshooting the problem? Has anyone experienced
> something like this before?
>
> Thanks,
>
> Luke-Jr
>
> P.S. Please CC me if possible.
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PCI bridge missing
2006-09-28 21:24 PCI bridge missing Luke-Jr
2006-09-28 21:39 ` Mark Knecht
2006-09-28 21:52 ` Mark Felder
@ 2006-09-28 23:14 ` Alan Cox
2006-09-29 0:17 ` Luke-Jr
2006-09-29 17:28 ` Luke-Jr
2 siblings, 2 replies; 10+ messages in thread
From: Alan Cox @ 2006-09-28 23:14 UTC (permalink / raw)
To: Luke-Jr; +Cc: linux-kernel
Ar Iau, 2006-09-28 am 16:24 -0500, ysgrifennodd Luke-Jr:
> However, this bridge is completely ignored and unseen by Linux. It does not
> show up in lspci or dmesg (as far as I can tell) at all. The daughterboard is
> plugged in, and the PCI cards on it are powered.
lspci -vvxxx would be interesting
Linux on PC assumes the BIOS did the work needed so if there is some
custom "enabler" driver in the Windows for it that might explain
problems.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PCI bridge missing
2006-09-28 23:14 ` Alan Cox
@ 2006-09-29 0:17 ` Luke-Jr
2006-09-29 11:36 ` Mark Brown
2006-09-29 17:28 ` Luke-Jr
1 sibling, 1 reply; 10+ messages in thread
From: Luke-Jr @ 2006-09-29 0:17 UTC (permalink / raw)
To: Alan Cox, Mark Knecht; +Cc: linux-kernel
On Thursday 28 September 2006 21:39, you wrote:
> Anyway, maybe you haven't cold booted the machine and could try that?
It's been cold-booted a few times, though I can't guarantee that for each
kernel I tried.
On Thursday 28 September 2006 23:14, Alan Cox wrote:
> Ar Iau, 2006-09-28 am 16:24 -0500, ysgrifennodd Luke-Jr:
> > However, this bridge is completely ignored and unseen by Linux. It does
> > not show up in lspci or dmesg (as far as I can tell) at all. The
> > daughterboard is plugged in, and the PCI cards on it are powered.
>
> lspci -vvxxx would be interesting
Will do tomorrow.
> Linux on PC assumes the BIOS did the work needed
pci=nobios doesn't bypass that assumption? (I tried that too)
> so if there is some custom "enabler" driver in the Windows for it that might
> explain problems.
Some old Debian (2.2) manual at least implied it worked at one point. That's
where I compared the lspci from. So this would be a regression, a hardware
failure, or a misconfiguration.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PCI bridge missing
2006-09-29 0:17 ` Luke-Jr
@ 2006-09-29 11:36 ` Mark Brown
0 siblings, 0 replies; 10+ messages in thread
From: Mark Brown @ 2006-09-29 11:36 UTC (permalink / raw)
To: linux-kernel
On Fri, Sep 29, 2006 at 12:17:32AM +0000, Luke-Jr wrote:
> On Thursday 28 September 2006 21:39, you wrote:
> > so if there is some custom "enabler" driver in the Windows for it that might
> > explain problems.
> Some old Debian (2.2) manual at least implied it worked at one point. That's
> where I compared the lspci from. So this would be a regression, a hardware
> failure, or a misconfiguration.
I've used some of these boxes - they've always worked just fine in the
past, though I've not tried anything more current than earlyish 2.6
kernels I think.
--
"You grabbed my hand and we fell into it, like a daydream - or a fever."
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PCI bridge missing
2006-09-28 23:14 ` Alan Cox
2006-09-29 0:17 ` Luke-Jr
@ 2006-09-29 17:28 ` Luke-Jr
2006-09-29 18:18 ` Alan Cox
1 sibling, 1 reply; 10+ messages in thread
From: Luke-Jr @ 2006-09-29 17:28 UTC (permalink / raw)
To: Alan Cox; +Cc: linux-kernel
On Thursday 28 September 2006 6:14 pm, Alan Cox wrote:
> lspci -vvxxx would be interesting
gnat:~# lspci -vvxxx
0000:00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
00: 86 80 90 71 06 01 10 22 03 00 00 06 00 40 00 00
10: 08 00 00 f4 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 8c 03 00 00 00 00 00 09 03 10 11 11 00 00 00 00
60: 00 00 08 10 18 20 20 20 00 0a 00 a0 0a 00 00 00
70: 20 1f 0a 38 50 05 07 01 00 3c 10 38 00 00 00 00
80: 02 00 0a 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 44 00 00 04 61 00 00 00 05 00 00 00 00 00 00
a0: 02 00 10 00 03 02 00 1f 00 00 00 00 00 00 00 00
b0: 80 20 00 00 30 00 00 00 00 00 62 0f 20 10 00 00
c0: 00 00 00 00 00 00 00 00 18 0c ff ff 7f 00 00 00
d0: 08 08 02 02 02 12 00 00 0c 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 f8 00 60 20 0f 00 00 00 00 00 00
0000:00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP
bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fc000000-feffffff
Prefetchable memory behind bridge: f9000000-f9ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00: 86 80 91 71 1f 01 20 02 03 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 40 e0 e0 a0 22
20: 00 fc f0 fe 00 f9 f0 f9 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 86 80 10 71 0f 00 80 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 4d 00 20 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 09 80 80 0b 10 00 00 00 00 f6 80 00 00 00 00 00
70: 00 00 00 00 00 00 0c 0c 00 00 00 00 00 00 00 00
80: 00 00 07 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 05 00 00 e1 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 21 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
0000:00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at ffa0 [size=16]
00: 86 80 11 71 05 00 80 02 01 80 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: a1 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 07 e3 07 e3 00 00 00 00 01 00 02 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
0000:00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev
01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at dce0 [size=32]
00: 86 80 12 71 05 00 80 02 01 00 03 0c 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: e1 dc 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 10
0000:00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00: 86 80 13 71 01 00 80 02 02 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 08 00 00 00 01 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 04 00 00 02 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 51 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
0000:00:11.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone]
(rev 24)
Subsystem: Dell 3C905B Fast Etherlink XL 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at dc00 [size=128]
Region 1: Memory at ff000000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at fb000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: b7 10 55 90 17 01 10 02 24 00 00 02 08 40 00 00
10: 01 dc 00 00 00 00 00 ff 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 82 00
30: 00 00 00 fb dc 00 00 00 00 00 00 00 0b 01 0a 0a
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 01 76
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP
1X/2X (rev 5c) (prog-if 00 [VGA])
Subsystem: Dell Optiplex GX1 Onboard Display Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at ec00 [size=256]
Region 2: Memory at fcfff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at f9000000 [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
00: 02 10 42 47 87 00 90 02 5c 00 00 03 08 40 00 00
10: 00 00 00 fd 01 ec 00 00 00 f0 ff fc 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 82 40
30: 00 00 00 00 50 00 00 00 00 00 00 00 09 01 08 00
40: 0c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 02 00 10 00 03 02 00 ff 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: PCI bridge missing
2006-09-29 17:28 ` Luke-Jr
@ 2006-09-29 18:18 ` Alan Cox
2006-09-29 17:57 ` Luke-Jr
2006-09-29 18:53 ` Luke-Jr
0 siblings, 2 replies; 10+ messages in thread
From: Alan Cox @ 2006-09-29 18:18 UTC (permalink / raw)
To: Luke-Jr; +Cc: linux-kernel
Ar Gwe, 2006-09-29 am 12:28 -0500, ysgrifennodd Luke-Jr:
> On Thursday 28 September 2006 6:14 pm, Alan Cox wrote:
> > lspci -vvxxx would be interesting
>
Ok so the 21152 just isn't seen by Linux. Ok try this
lspci -vvxxx -H1 -M
that will try and do a hardware level scan and map
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PCI bridge missing
2006-09-29 18:18 ` Alan Cox
@ 2006-09-29 17:57 ` Luke-Jr
2006-09-29 18:53 ` Luke-Jr
1 sibling, 0 replies; 10+ messages in thread
From: Luke-Jr @ 2006-09-29 17:57 UTC (permalink / raw)
To: Alan Cox; +Cc: linux-kernel
gnat:~# lspci -vvxxx -H1 -M
0000:00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f4000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
00: 86 80 90 71 06 01 10 22 03 00 00 06 00 40 00 00
10: 08 00 00 f4 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 8c 03 00 00 00 00 00 09 03 10 11 11 00 00 00 00
60: 00 00 08 10 18 20 20 20 00 0a 00 a0 0a 00 00 00
70: 20 1f 0a 38 50 05 07 01 00 3c 10 38 00 00 00 00
80: 02 00 0a 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 44 00 00 04 61 00 00 00 05 00 00 00 00 00 00
a0: 02 00 10 00 03 02 00 1f 00 00 00 00 00 00 00 00
b0: 80 20 00 00 30 00 00 00 00 00 62 0f 20 10 00 00
c0: 00 00 00 00 00 00 00 00 18 0c ff ff 7f 00 00 00
d0: 08 08 02 02 02 12 00 00 0c 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 f8 00 60 20 0f 00 00 00 00 00 00
0000:00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP
bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fc000000-feffffff
Prefetchable memory behind bridge: f9000000-f9ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00: 86 80 91 71 1f 01 20 02 03 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 40 e0 e0 a0 22
20: 00 fc f0 fe 00 f9 f0 f9 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
## 00.01:0 is a bridge from 00 to 01-01
0000:00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 86 80 10 71 0f 00 80 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 4d 00 20 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 09 80 80 0b 10 00 00 00 00 f6 80 00 00 00 00 00
70: 00 00 00 00 00 00 0c 0c 00 00 00 00 00 00 00 00
80: 00 00 07 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 05 00 00 e1 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 21 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
0000:00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at ffa0
00: 86 80 11 71 05 00 80 02 01 80 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: a1 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 07 e3 07 e3 00 00 00 00 01 00 02 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
0000:00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev
01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at dce0
00: 86 80 12 71 05 00 80 02 01 00 03 0c 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: e1 dc 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 10
0000:00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00: 86 80 13 71 01 00 80 02 02 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 08 00 00 00 01 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 04 00 00 02 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 51 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
0000:00:11.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone]
(rev 24)
Subsystem: Dell 3C905B Fast Etherlink XL 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at dc00
Region 1: Memory at ff000000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: b7 10 55 90 17 01 10 02 24 00 00 02 08 40 00 00
10: 01 dc 00 00 00 00 00 ff 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 82 00
30: 00 00 00 fb dc 00 00 00 00 00 00 00 0b 01 0a 0a
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 01 76
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP
1X/2X (rev 5c) (prog-if 00 [VGA])
Subsystem: Dell Optiplex GX1 Onboard Display Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fd000000 (32-bit, non-prefetchable)
Region 1: I/O ports at ec00
Region 2: Memory at fcfff000 (32-bit, non-prefetchable)
Capabilities: [50] AGP version 1.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
00: 02 10 42 47 87 00 90 02 5c 00 00 03 08 40 00 00
10: 00 00 00 fd 01 ec 00 00 00 f0 ff fc 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 82 40
30: 00 00 00 00 50 00 00 00 00 00 00 00 09 01 08 00
40: 0c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 02 00 10 00 03 02 00 ff 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Summary of buses:
00: Primary host bus
01.0 Bridge to 01-01
01: Entered via 00:01.0
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: PCI bridge missing
2006-09-29 18:18 ` Alan Cox
2006-09-29 17:57 ` Luke-Jr
@ 2006-09-29 18:53 ` Luke-Jr
1 sibling, 0 replies; 10+ messages in thread
From: Luke-Jr @ 2006-09-29 18:53 UTC (permalink / raw)
To: Alan Cox; +Cc: linux-kernel
Go figure. Apparently the counterfiet-3Com NIC somehow disables the entire
daughterboard. I found another GX1p and used its daughterboard, noticed it
worked, then assumed the first one was bad... put the NIC in the second one
and it's "bad" all of a sudden. Both show up in lspci if I take the NICs out.
FWIW, the NIC claims to be 3C905CX-TXM assembled in USA and matches the
picture of the counterfeit 3Com cards in
http://www.heise.de/newsticker/data/ea-20.08.02-000/ (bottom of the second
picture)
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2006-09-29 18:53 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2006-09-28 21:24 PCI bridge missing Luke-Jr
2006-09-28 21:39 ` Mark Knecht
2006-09-28 21:52 ` Mark Felder
2006-09-28 23:14 ` Alan Cox
2006-09-29 0:17 ` Luke-Jr
2006-09-29 11:36 ` Mark Brown
2006-09-29 17:28 ` Luke-Jr
2006-09-29 18:18 ` Alan Cox
2006-09-29 17:57 ` Luke-Jr
2006-09-29 18:53 ` Luke-Jr
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox