From: Adrian Bunk <bunk@stusta.de>
To: Olivier Nicolas <olivn@trollprod.org>,
Stephen Hemminger <shemminger@osdl.org>,
Takashi Iwai <tiwai@suse.de>, Jaroslav Kysela <perex@suse.cz>
Cc: linux-kernel@vger.kernel.org, alsa-devel@alsa-project.org,
gregkh@suse.de, linux-pci@atrey.karlin.mff.cuni.cz,
len.brown@intel.com, linux-acpi@vger.kernel.org,
"Eric W. Biederman" <ebiederm@xmission.com>,
Andrew Morton <akpm@osdl.org>, Linus Torvalds <torvalds@osdl.org>
Subject: Re: 2.6.19-rc5 x86_64 irq 22: nobody cared
Date: Thu, 9 Nov 2006 07:49:56 +0100 [thread overview]
Message-ID: <20061109064956.GG4729@stusta.de> (raw)
In-Reply-To: <4551D12D.4010304@trollprod.org>
On Wed, Nov 08, 2006 at 01:44:29PM +0100, Olivier Nicolas wrote:
> Hi,
Hi Olivier,
> 2.6.19-rc5 does not boot properly, I have tried pci=routeirq, irpoll
> without success.
>
> Full details (.config, dmesg, /proc/interrupts) are in
> http://olivn.trollprod.org/2.6.19-rc5-irq.tar.gz
thanks for your report!
I might be wrong, but looking at the dmesg:
- irq 22 is the hda_intel IRQ
- the "irq 22: nobody cared" is immediately before the
"hda_intel: No response from codec, disabling MSI..."
- in the routeirq case, the hda_intel IRQ as well as the
IRQ in the error message change to 21
So it might be related to the hda_intel MSI check.
If this was a wrong guess, other interesting messages in the dmesg are:
<-- snip -->
...
PCI: Using MMCONFIG at f0000000
PCI: No mmconfig possible on device 00:18
...
PCI: Setting latency timer of device 0000:00:03.0 to 64
pcie_portdrv_probe->Dev[02fd:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie03]
PCI: Setting latency timer of device 0000:00:04.0 to 64
pcie_portdrv_probe->Dev[02fb:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie03]
PCI: Setting latency timer of device 0000:00:12.0 to 64
pcie_portdrv_probe->Dev[0376:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:12.0:pcie00]
Allocate Port Service[0000:00:12.0:pcie03]
PCI: Setting latency timer of device 0000:00:14.0 to 64
pcie_portdrv_probe->Dev[0374:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:14.0:pcie00]
Allocate Port Service[0000:00:14.0:pcie03]
PCI: Setting latency timer of device 0000:00:16.0 to 64
pcie_portdrv_probe->Dev[0375:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:16.0:pcie00]
Allocate Port Service[0000:00:16.0:pcie03]
PCI: Setting latency timer of device 0000:00:17.0 to 64
pcie_portdrv_probe->Dev[0377:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:17.0:pcie00]
Allocate Port Service[0000:00:17.0:pcie03]
...
<-- snip -->
> Olivier
>
> System: ASUS M2N32-SLI, AMD64 X2 Dual Core 4600
>
>
> kernel 2.6.9-rc5
>
> irq 22: nobody cared (try booting with the "irqpoll" option)
>
> Call Trace:
> <IRQ> [<ffffffff80259055>] __report_bad_irq+0x35/0x90
> [<ffffffff802592d3>] note_interrupt+0x223/0x280
> [<ffffffff80259d41>] handle_fasteoi_irq+0xb1/0xf0
> [<ffffffff8020b17c>] call_softirq+0x1c/0x30
> [<ffffffff8020d1ba>] do_IRQ+0x8a/0xe0
> [<ffffffff8020a571>] ret_from_intr+0x0/0xa
> <EOI>
> handlers:
> [<ffffffff8807f150>] (nv_generic_interrupt+0x0/0xc0 [sata_nv])
> Disabling IRQ #22
>
>
> CPU0 CPU1
> 0: 223 45540 IO-APIC-edge timer
> 1: 1 402 IO-APIC-edge i8042
> 6: 1 4 IO-APIC-edge floppy
> 8: 0 0 IO-APIC-edge rtc
> 9: 0 0 IO-APIC-fasteoi acpi
> 12: 0 103 IO-APIC-edge i8042
> 14: 7 140 IO-APIC-edge ide0
> 16: 0 0 IO-APIC-fasteoi libata
> 17: 0 10 IO-APIC-fasteoi bttv0
> 20: 0 20 IO-APIC-fasteoi ehci_hcd:usb1
> 21: 0 0 IO-APIC-fasteoi libata
> 22: 214 99786 IO-APIC-fasteoi libata, HDA Intel
> 23: 76 6230 IO-APIC-fasteoi libata, ohci_hcd:usb2
> 308: 5 3169 PCI-MSI-edge eth1
> 309: 0 10 PCI-MSI-edge eth1
> 310: 0 44 PCI-MSI-edge eth1
> 311: 1 3193 PCI-MSI-edge eth0
> 312: 0 0 PCI-MSI-edge eth0
> 313: 0 1 PCI-MSI-edge eth0
> NMI: 64 68
> LOC: 45716 45691
> ERR: 0
>
>
>
> kernel 2.6.19-rc5 with pci=routeirq
>
> irq 21: nobody cared (try booting with the "irqpoll" option)
>
> Call Trace:
> <IRQ> [<ffffffff80259055>] __report_bad_irq+0x35/0x90
> [<ffffffff802592d3>] note_interrupt+0x223/0x280
> [<ffffffff80259d41>] handle_fasteoi_irq+0xb1/0xf0
> [<ffffffff8020b17c>] call_softirq+0x1c/0x30
> [<ffffffff8020d1ba>] do_IRQ+0x8a/0xe0
> [<ffffffff802092f0>] default_idle+0x0/0x50
> [<ffffffff8020a571>] ret_from_intr+0x0/0xa
> <EOI> [<ffffffff80209319>] default_idle+0x29/0x50
> [<ffffffff8020939b>] cpu_idle+0x5b/0x80
> [<ffffffff8050039c>] start_secondary+0x50c/0x520
>
> handlers:
> [<ffffffff880e6fd0>] (usb_hcd_irq+0x0/0x60 [usbcore])
> Disabling IRQ #21
>
> CPU0 CPU1
> 0: 214 24856 IO-APIC-edge timer
> 1: 0 359 IO-APIC-edge i8042
> 6: 0 5 IO-APIC-edge floppy
> 8: 0 0 IO-APIC-edge rtc
> 9: 0 0 IO-APIC-fasteoi acpi
> 12: 0 103 IO-APIC-edge i8042
> 14: 0 128 IO-APIC-edge ide0
> 16: 0 0 IO-APIC-fasteoi libata
> 17: 1 2 IO-APIC-fasteoi bttv0
> 20: 22 6469 IO-APIC-fasteoi libata
> 21: 11 99989 IO-APIC-fasteoi ehci_hcd:usb2, HDA Intel
> 22: 0 1 IO-APIC-fasteoi libata, ohci_hcd:usb1
> 23: 0 0 IO-APIC-fasteoi libata
> 308: 8 2378 PCI-MSI-edge eth1
> 309: 0 9 PCI-MSI-edge eth1
> 310: 0 9 PCI-MSI-edge eth1
> 311: 4 2401 PCI-MSI-edge eth0
> 312: 0 0 PCI-MSI-edge eth0
> 313: 0 1 PCI-MSI-edge eth0
> NMI: 74 47
> LOC: 25024 24991
> ERR: 0
>
>
>
> kernel 2.6.19-rc5 with irqpoll
>
> Hang during boot
> (See screenshot in http://olivn.trollprod.org/2.6.19-rc5-irq.tar.gz)
>
>
>
> kernel 2.6.18 (works without any problem)
>
> CPU0 CPU1
> 0: 1590 998089 IO-APIC-edge timer
> 1: 2 657 IO-APIC-edge i8042
> 6: 0 5 IO-APIC-edge floppy
> 8: 0 0 IO-APIC-edge rtc
> 9: 0 0 IO-APIC-level acpi
> 12: 194 59353 IO-APIC-edge i8042
> 14: 13 6381 IO-APIC-edge ide0
> 50: 0 0 IO-APIC-level libata
> 58: 0 0 IO-APIC-level libata
> 66: 109 181425 IO-APIC-level libata, nvidia
> 74: 41 963 IO-APIC-level ehci_hcd:usb1, HDA Intel
> 82: 4 6 IO-APIC-level bttv0
> 90: 0 0 PCI-MSI-X eth0
> 98: 3 0 PCI-MSI-X eth0
> 106: 212234 0 PCI-MSI-X eth0
> 114: 532 0 PCI-MSI-X eth1
> 122: 445 0 PCI-MSI-X eth1
> 130: 212217 0 PCI-MSI-X eth1
> 233: 73 23009 IO-APIC-level libata, ohci_hcd:usb2
> NMI: 99 104
> LOC: 999684 999664
> ERR: 0
> MIS: 0
next prev parent reply other threads:[~2006-11-09 6:49 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-11-08 12:44 2.6.19-rc5 x86_64 irq 22: nobody cared Olivier Nicolas
2006-11-09 6:49 ` Adrian Bunk [this message]
2006-11-09 7:55 ` Yinghai Lu
2006-11-09 9:29 ` Olivier Nicolas
2006-11-09 10:38 ` Takashi Iwai
2006-11-09 16:08 ` Olivier Nicolas
2006-11-09 16:49 ` Stephen Hemminger
2006-11-09 17:12 ` Eric W. Biederman
2006-11-09 8:17 ` Len Brown
-- strict thread matches above, loose matches on Subject: below --
2006-11-09 21:03 Lu, Yinghai
2006-11-10 2:09 Lu, Yinghai
2006-11-10 9:56 ` Olivier Nicolas
2006-11-10 18:20 Lu, Yinghai
2006-11-10 20:11 ` Eric W. Biederman
2006-11-10 20:16 Lu, Yinghai
2006-11-10 20:22 Lu, Yinghai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20061109064956.GG4729@stusta.de \
--to=bunk@stusta.de \
--cc=akpm@osdl.org \
--cc=alsa-devel@alsa-project.org \
--cc=ebiederm@xmission.com \
--cc=gregkh@suse.de \
--cc=len.brown@intel.com \
--cc=linux-acpi@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@atrey.karlin.mff.cuni.cz \
--cc=olivn@trollprod.org \
--cc=perex@suse.cz \
--cc=shemminger@osdl.org \
--cc=tiwai@suse.de \
--cc=torvalds@osdl.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox