* PCI probing failure in 2.6.21-rc3
@ 2007-03-14 8:47 Francis Moreau
2007-03-15 19:06 ` Andrew Morton
0 siblings, 1 reply; 5+ messages in thread
From: Francis Moreau @ 2007-03-14 8:47 UTC (permalink / raw)
To: linux-kernel
[-- Attachment #1: Type: text/plain, Size: 944 bytes --]
Hi,
I already posted this issue but it was on a 2.6.19.7 kernel
(2.6.19-1.2911.6.5.fc6 to be accurate). So it doesn't seem to be a
regression.
During boot the console shows up this:
[...]
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
0000:00:1f.2: trying to change BAR0 from 0000 to 01F0
0000:00:1f.2: trying to change BAR1 from 0000 to 03F4
0000:00:1f.2: trying to change BAR2 from 0000 to 0170
0000:00:1f.2: trying to change BAR3 from 0000 to 0374
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06 (-#07)
(try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
[...]
I haven't time to test 'pci=assign-busses' option, I'll do it later,
but I wanted to report this ASAP.
dmesg, lspci and lsmod outputs attached.
--
Francis
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain; name=dmesg.txt; charset=ANSI_X3.4-1968, Size: 25426 bytes --]
Linux version 2.6.21-rc3 (fmoreau@laptop) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-51)) #1 SMP Wed Mar 14 08:55:15 CET 2007
Command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fe80000 (usable)
BIOS-e820: 000000003fe80000 - 000000003ff00000 (ACPI NVS)
BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 261760) 1 entries of 3200 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F64E0, 0014 (r0 PTLTD )
ACPI: RSDT 3FE85369, 0050 (r1 PTLTD Capell00 6040000 LTP 0)
ACPI: FACP 3FE8CE20, 0074 (r1 Acer Grape 6040000 LOHR 5A)
ACPI: DSDT 3FE8708A, 5D96 (r1 Acer CALISTGA 6040000 INTL 20050228)
ACPI: FACS 3FE8DFC0, 0040
ACPI: APIC 3FE8CE94, 0068 (r1 Acer Grape 6040000 LOHR 5A)
ACPI: HPET 3FE8CEFC, 0038 (r1 Acer Grape 6040000 LOHR 5A)
ACPI: MCFG 3FE8CF34, 003C (r1 Acer Grape 6040000 LOHR 5A)
ACPI: APIC 3FE8CF70, 0068 (r1 PTLTD APIC 6040000 LTP 0)
ACPI: BOOT 3FE8CFD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
ACPI: SSDT 3FE86A3B, 064F (r1 SataRe SataPri 1000 INTL 20050228)
ACPI: SSDT 3FE863A9, 0692 (r1 SataRe SataSec 1000 INTL 20050228)
ACPI: SSDT 3FE85945, 025F (r1 PmRef Cpu0Tst 3000 INTL 20050228)
ACPI: SSDT 3FE8589F, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20050228)
ACPI: SSDT 3FE853B9, 04E6 (r1 PmRef CpuPm 3000 INTL 20050228)
No NUMA configuration found
Faking a node at 0000000000000000-000000003fe80000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 261760) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000003fe80000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 261760
On node 0 totalpages: 261663
DMA zone: 64 pages used for memmap
DMA zone: 1340 pages reserved
DMA zone: 2595 pages, LIFO batch:0
DMA32 zone: 4026 pages used for memmap
DMA32 zone: 253638 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000e0000
Nosave address range: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 43136 bytes of per cpu data
Built 1 zonelists. Total pages: 256233
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Detected 1662.498 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 1020800k/1047040k available (2412k kernel code, 25852k reserved, 1431k data, 324k init)
Calibrating delay using timer specific routine.. 3328.45 BogoMIPS (lpj=1664227)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 10390607
Detected 10.390 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3325.04 BogoMIPS (lpj=1662520)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz stepping 06
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=25
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - efffffff
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
0000:00:1f.2: trying to change BAR0 from 0000 to 01F0
0000:00:1f.2: trying to change BAR1 from 0000 to 03F4
0000:00:1f.2: trying to change BAR2 from 0000 to 0170
0000:00:1f.2: trying to change BAR3 from 0000 to 0374
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06 (-#07) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 5 *6 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 5 6 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 5 6 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 5 6 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 5 6 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 5 6 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 5 6 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 *5 6 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.0
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
pnp: 00:01: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
pnp: 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
pnp: 00:04: iomem range 0xfed00000-0xfed003ff has been reserved
PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: d0000000-d1ffffff
PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
Time: hpet clocksource has been installed.
PCI: Bridge: 0000:00:1c.2
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
IO window: disabled.
MEM window: d2100000-d21fffff
PREFETCH window: disabled.
PCI: Bus 7, cardbus bridge: 0000:06:04.0
IO window: 00002000-000020ff
IO window: 00002400-000024ff
PREFETCH window: 50000000-53ffffff
MEM window: 54000000-57ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 2000-2fff
MEM window: d2000000-d20fffff
PREFETCH window: 50000000-53ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 16 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 65536 (order: 9, 2621440 bytes)
TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2308k freed
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1173859627.753:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Allocate Port Service[0000:00:1c.3:pcie03]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: SSDT 3FE860EB, 01F6 (r1 PmRef Cpu0Ist 3000 INTL 20050228)
ACPI: SSDT 3FE85BA4, 04C2 (r1 PmRef Cpu0Cst 3001 INTL 20050228)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 3FE862E1, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20050228)
ACPI: SSDT 3FE86066, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050228)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [TZ00] (45 C)
ACPI: Thermal Zone [TZ01] (45 C)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 945GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: Slimtype DVDRW SSM-8515S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ide-floppy driver 0.99.newide
Yenta: CardBus bridge found at 0000:06:04.0 [1025:0090]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:04.0, mfunc 0x90501212, devctl 0x44
Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
pcmcia: parent PCI bridge Memory window: 0xd2000000 - 0xd20fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:MSS0] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 324k freed
Write protecting the kernel read-only data: 1074k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 0xa04713/0x204000
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
input: SynPS/2 Synaptics TouchPad as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd2404000
usb 2-2: new full speed USB device using uhci_hcd and address 2
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
SCSI subsystem initialized
libata version 2.20 loaded.
ata_piix 0000:00:1f.2: version 2.10ac1
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ata: 0x170 IDE port busy
ata: conflict with ide1
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x00000000000118b0 irq 14
ata2: DUMMY
scsi0 : ata_piix
usb 5-4: new high speed USB device using ehci_hcd and address 2
usb 5-4: configuration #1 chosen from 1 choice
ata1.00: ATA-7: Hitachi HTS541212H9AT00, HP4OA23C, max UDMA/100
ata1.00: 234441648 sectors, multi 16: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
scsi1 : ata_piix
scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54121 HP4O PQ: 0 ANSI: 5
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
usb 4-1: new low speed USB device using uhci_hcd and address 2
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 4-1: configuration #1 chosen from 1 choice
input: Microsoft Microsoft Wireless Optical Mouse® 1.00 as /class/input/input2
input: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse® 1.00] on usb-0000:00:1d.3-1
security: 3 users, 6 roles, 1604 types, 175 bools, 1 sens, 1024 cats
security: 59 classes, 50462 rules
security: class dccp_socket not defined in policy
security: permission dccp_recv in class node not defined in policy
security: permission dccp_send in class node not defined in policy
security: permission dccp_recv in class netif not defined in policy
security: permission dccp_send in class netif not defined in policy
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1173859632.231:2): policy loaded auid=4294967295
hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:06:04.2 [1524:0550] (rev 1)
PCI: Enabling device 0000:06:04.2 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:04.2[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:06:04.2 to 64
mmc0: SDHCI at 0xd2003400 irq 17 DMA
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:06:01.0 to 64
eth0: Broadcom 4400 10/100BaseT Ethernet 00:16:d4:54:64:8f
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
intel_rng: FWH not detected
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input3
sd 0:0:0:0: Attached scsi generic sg0 type 0
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
floppy0: no floppy controllers found
lp: driver loaded but no devices found
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ACPI: AC Adapter [ACAD] (off-line)
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [SLPB]
input: Power Button (CM) as /class/input/input7
ACPI: Power Button (CM) [PWRB]
No dock devices found.
ibm_acpi: ec object not found
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda5, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
usb 2-1: new full speed USB device using uhci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 2:0:0:0: Direct-Access IBEAD Multi Player 0100 PQ: 0 ANSI: 4
SCSI device sdb: 503040 512-byte hdwr sectors (258 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 503040 512-byte hdwr sectors (258 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: Attached scsi removable disk sdb
sd 2:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
SELinux: initialized (dev sdb1, type vfat), uses genfs_contexts
[-- Attachment #3: lspci.txt --]
[-- Type: text/plain, Size: 22722 bytes --]
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub (rev 03)
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express PCI Express Root Port (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d0000000-d1ffffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cff00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4069
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 1, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
Capabilities: [140] Unknown (5)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d2400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 2, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4071
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 3, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4079
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 4, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4081
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d2100000-d21fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 5, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4089
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1800 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1820 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1840 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 1860 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d2404000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=06, subordinate=0a, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d2000000-d20fffff
Prefetchable memory behind bridge: 0000000050000000-0000000053f00000
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller IDE (rev 02) (prog-if 80 [Master])
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 18b0 [size=16]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 18c0 [size=32]
01:00.0 VGA compatible controller: nVidia Corporation Quadro NVS 110M / GeForce Go 7300 (rev a1) (prog-if 00 [VGA])
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 6
Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d0000000 (64-bit, non-prefetchable) [size=16M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <256ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <256ns, L1 <4us
Link: ASPM L1 Enabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting
05:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)
Subsystem: Intel Corporation Unknown device 1001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d2100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number 8c-b1-25-ff-ff-de-18-00
06:01.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d2000000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
06:04.0 CardBus bridge: ENE Technology Inc CB-712/4 Cardbus Controller (rev 10)
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d2002000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 50000000-53fff000 (prefetchable)
Memory window 1: 54000000-57fff000
I/O window 0: 00002000-000020ff
I/O window 1: 00002400-000024ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
06:04.1 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 0: Memory at d2003000 (32-bit, non-prefetchable) [disabled] [size=128]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:04.2 Class 0805: ENE Technology Inc ENE PCI Secure Digital Card Reader Controller (rev 01) (prog-if 01)
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 18000ns max)
Interrupt: pin B routed to IRQ 17
Region 0: Memory at d2003400 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:04.3 FLASH memory: ENE Technology Inc FLASH memory: ENE Technology Inc: (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 0: Memory at d2003800 (32-bit, non-prefetchable) [disabled] [size=128]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:04.4 FLASH memory: ENE Technology Inc Unknown device 0551 (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 0090
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 255
Region 0: Memory at d2003100 (32-bit, non-prefetchable) [disabled] [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[-- Attachment #4: lsmod.txt --]
[-- Type: text/plain, Size: 2921 bytes --]
Module Size Used by
vfat 18176 1
fat 58864 1 vfat
usb_storage 77504 1
autofs4 29512 2
hidp 30272 2
rfcomm 49640 0
l2cap 33408 10 hidp,rfcomm
bluetooth 65988 5 hidp,rfcomm,l2cap
sunrpc 185384 1
iptable_filter 7808 0
ip_tables 24808 1 iptable_filter
ip6t_REJECT 10176 1
xt_tcpudp 8128 5
ip6table_filter 7616 1
ip6_tables 19400 1 ip6table_filter
x_tables 25608 4 ip_tables,ip6t_REJECT,xt_tcpudp,ip6_tables
acpi_cpufreq 15816 1
dm_multipath 24336 0
video 24208 0
sbs 21776 0
i2c_ec 10496 1 sbs
dock 15968 0
button 13728 0
battery 15880 0
asus_acpi 23468 0
ac 10696 0
ipv6 312544 19 ip6t_REJECT
parport_pc 34472 0
lp 19280 0
parport 45708 2 parport_pc,lp
snd_hda_intel 27232 2
snd_hda_codec 260096 1 snd_hda_intel
snd_seq_dummy 8644 0
joydev 15680 0
snd_seq_oss 37248 0
snd_seq_midi_event 12800 1 snd_seq_oss
snd_seq 60320 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 13268 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss 49088 0
snd_mixer_oss 21568 1 snd_pcm_oss
snd_pcm 89992 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_timer 29256 2 snd_seq,snd_pcm
sg 41896 0
pcspkr 8000 0
snd 68840 13 snd_hda_intel,snd_hda_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 13536 1 snd
snd_page_alloc 14992 2 snd_hda_intel,snd_pcm
shpchp 38940 0
iTCO_wdt 16416 0
b44 34380 0
mii 10432 1 b44
i2c_i801 13524 0
sdhci 23756 0
i2c_core 28864 2 i2c_ec,i2c_i801
mmc_core 35720 1 sdhci
ide_cd 45472 0
cdrom 40360 1 ide_cd
serio_raw 12228 0
dm_snapshot 21552 0
dm_zero 6592 0
dm_mirror 26944 0
dm_mod 66320 9 dm_multipath,dm_snapshot,dm_zero,dm_mirror
ata_piix 21380 2
libata 125352 1 ata_piix
sd_mod 26176 5
scsi_mod 161816 4 usb_storage,sg,libata,sd_mod
ext3 138320 2
jbd 69808 1 ext3
ehci_hcd 38988 0
ohci_hcd 26436 0
uhci_hcd 30496 0
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: PCI probing failure in 2.6.21-rc3
2007-03-14 8:47 PCI probing failure in 2.6.21-rc3 Francis Moreau
@ 2007-03-15 19:06 ` Andrew Morton
2007-03-15 21:06 ` Francis Moreau
` (2 more replies)
0 siblings, 3 replies; 5+ messages in thread
From: Andrew Morton @ 2007-03-15 19:06 UTC (permalink / raw)
To: Francis Moreau; +Cc: linux-kernel, Greg KH
> On Wed, 14 Mar 2007 09:47:42 +0100 "Francis Moreau" <francis.moro@gmail.com> wrote:
> I already posted this issue but it was on a 2.6.19.7 kernel
> (2.6.19-1.2911.6.5.fc6 to be accurate). So it doesn't seem to be a
> regression.
>
> During boot the console shows up this:
>
> [...]
> PCI: Probing PCI hardware (bus 00)
> PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
> PCI quirk: region 1180-11bf claimed by ICH6 GPIO
> 0000:00:1f.2: trying to change BAR0 from 0000 to 01F0
> 0000:00:1f.2: trying to change BAR1 from 0000 to 03F4
> 0000:00:1f.2: trying to change BAR2 from 0000 to 0170
> 0000:00:1f.2: trying to change BAR3 from 0000 to 0374
> Boot video device is 0000:01:00.0
> PCI: Transparent bridge - 0000:00:1e.0
> PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06 (-#07)
> (try 'pci=assign-busses')
> Please report the result to linux-kernel to fix this permanently
> [...]
>
> I haven't time to test 'pci=assign-busses' option, I'll do it later,
> but I wanted to report this ASAP.
Greg, could we please either
a) start doing something about these reports or
b) publish sufficient info to permit others to do something about these
reports or
c) remove the printk?
Thanks.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: PCI probing failure in 2.6.21-rc3
2007-03-15 19:06 ` Andrew Morton
@ 2007-03-15 21:06 ` Francis Moreau
2007-03-21 12:32 ` Francis Moreau
2007-03-23 22:49 ` Greg KH
2 siblings, 0 replies; 5+ messages in thread
From: Francis Moreau @ 2007-03-15 21:06 UTC (permalink / raw)
To: Andrew Morton; +Cc: linux-kernel, Greg KH
[-- Attachment #1: Type: text/plain, Size: 600 bytes --]
Hi
On 3/15/07, Andrew Morton <akpm@linux-foundation.org> wrote:
> Greg, could we please either
>
> a) start doing something about these reports or
> b) publish sufficient info to permit others to do something about these
> reports or
> c) remove the printk?
>
Thanks Andrew for considering.
I eventually tried to add "pci=assign-busses" as it was suggested by
the initial console output but I still have some issues I think. For
example:
$ dmesg
[...]
PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:01:00.0
[...]
I join the corresponding dmesg.
Hope that helps.
--
Francis
[-- Attachment #2: dmesg --]
[-- Type: application/octet-stream, Size: 25583 bytes --]
Linux version 2.6.21-rc3 (fmoreau@laptop) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-51)) #1 SMP Wed Mar 14 08:55:15 CET 2007
Command line: ro root=/dev/VolGroup00/LogVol00 rhgb pci=assign-busses
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fe80000 (usable)
BIOS-e820: 000000003fe80000 - 000000003ff00000 (ACPI NVS)
BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 261760) 1 entries of 3200 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F64E0, 0014 (r0 PTLTD )
ACPI: RSDT 3FE85369, 0050 (r1 PTLTD Capell00 6040000 LTP 0)
ACPI: FACP 3FE8CE20, 0074 (r1 Acer Grape 6040000 LOHR 5A)
ACPI: DSDT 3FE8708A, 5D96 (r1 Acer CALISTGA 6040000 INTL 20050228)
ACPI: FACS 3FE8DFC0, 0040
ACPI: APIC 3FE8CE94, 0068 (r1 Acer Grape 6040000 LOHR 5A)
ACPI: HPET 3FE8CEFC, 0038 (r1 Acer Grape 6040000 LOHR 5A)
ACPI: MCFG 3FE8CF34, 003C (r1 Acer Grape 6040000 LOHR 5A)
ACPI: APIC 3FE8CF70, 0068 (r1 PTLTD APIC 6040000 LTP 0)
ACPI: BOOT 3FE8CFD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
ACPI: SSDT 3FE86A3B, 064F (r1 SataRe SataPri 1000 INTL 20050228)
ACPI: SSDT 3FE863A9, 0692 (r1 SataRe SataSec 1000 INTL 20050228)
ACPI: SSDT 3FE85945, 025F (r1 PmRef Cpu0Tst 3000 INTL 20050228)
ACPI: SSDT 3FE8589F, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20050228)
ACPI: SSDT 3FE853B9, 04E6 (r1 PmRef CpuPm 3000 INTL 20050228)
No NUMA configuration found
Faking a node at 0000000000000000-000000003fe80000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 261760) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000003fe80000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 261760
On node 0 totalpages: 261663
DMA zone: 64 pages used for memmap
DMA zone: 1340 pages reserved
DMA zone: 2595 pages, LIFO batch:0
DMA32 zone: 4026 pages used for memmap
DMA32 zone: 253638 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000e0000
Nosave address range: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 43136 bytes of per cpu data
Built 1 zonelists. Total pages: 256233
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb pci=assign-busses
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Detected 1662.503 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 1020800k/1047040k available (2412k kernel code, 25852k reserved, 1431k data, 324k init)
Calibrating delay using timer specific routine.. 3328.49 BogoMIPS (lpj=1664246)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 10390648
Detected 10.390 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3325.03 BogoMIPS (lpj=1662519)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz stepping 06
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=24
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - efffffff
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
0000:00:1f.2: trying to change BAR0 from 0000 to 01F0
0000:00:1f.2: trying to change BAR1 from 0000 to 03F4
0000:00:1f.2: trying to change BAR2 from 0000 to 0170
0000:00:1f.2: trying to change BAR3 from 0000 to 0374
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 5 *6 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 5 6 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 5 6 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 5 6 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 5 6 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 5 6 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 5 6 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 *5 6 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.0
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
pnp: 00:01: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
Time: hpet clocksource has been installed.
pnp: 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
pnp: 00:04: iomem range 0xfed00000-0xfed003ff has been reserved
PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: d0000000-d1ffffff
PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
IO window: disabled.
MEM window: d2100000-d21fffff
PREFETCH window: disabled.
PCI: Bus 7, cardbus bridge: 0000:06:04.0
IO window: 00002000-000020ff
IO window: 00002400-000024ff
PREFETCH window: 50000000-53ffffff
MEM window: 54000000-57ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 2000-2fff
MEM window: d2000000-d20fffff
PREFETCH window: 50000000-53ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 16 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 65536 (order: 9, 2621440 bytes)
TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2308k freed
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1173995016.797:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Allocate Port Service[0000:00:1c.3:pcie03]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: SSDT 3FE860EB, 01F6 (r1 PmRef Cpu0Ist 3000 INTL 20050228)
ACPI: SSDT 3FE85BA4, 04C2 (r1 PmRef Cpu0Cst 3001 INTL 20050228)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 3FE862E1, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20050228)
ACPI: SSDT 3FE86066, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050228)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [TZ00] (41 C)
ACPI: Thermal Zone [TZ01] (41 C)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 945GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: Slimtype DVDRW SSM-8515S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ide-floppy driver 0.99.newide
Yenta: CardBus bridge found at 0000:06:04.0 [1025:0090]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:04.0, mfunc 0x90501212, devctl 0x44
Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
pcmcia: parent PCI bridge Memory window: 0xd2000000 - 0xd20fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:MSS0] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 324k freed
Write protecting the kernel read-only data: 1074k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 0xa04713/0x204000
input: SynPS/2 Synaptics TouchPad as /class/input/input1
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-2: new full speed USB device using uhci_hcd and address 2
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd2404000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
SCSI subsystem initialized
libata version 2.20 loaded.
ata_piix 0000:00:1f.2: version 2.10ac1
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ata: 0x170 IDE port busy
ata: conflict with ide1
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x00000000000118b0 irq 14
ata2: DUMMY
scsi0 : ata_piix
usb 5-4: new high speed USB device using ehci_hcd and address 2
usb 5-4: configuration #1 chosen from 1 choice
ata1.00: ATA-7: Hitachi HTS541212H9AT00, HP4OA23C, max UDMA/100
ata1.00: 234441648 sectors, multi 16: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
scsi1 : ata_piix
scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54121 HP4O PQ: 0 ANSI: 5
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
usb 4-1: new low speed USB device using uhci_hcd and address 2
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 4-1: configuration #1 chosen from 1 choice
input: Microsoft Microsoft Wireless Optical Mouse® 1.00 as /class/input/input2
input: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse® 1.00] on usb-0000:00:1d.3-1
security: 3 users, 6 roles, 1604 types, 175 bools, 1 sens, 1024 cats
security: 59 classes, 50462 rules
security: class dccp_socket not defined in policy
security: permission dccp_recv in class node not defined in policy
security: permission dccp_send in class node not defined in policy
security: permission dccp_recv in class netif not defined in policy
security: permission dccp_send in class netif not defined in policy
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1173995021.302:2): policy loaded auid=4294967295
hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:06:01.0 to 64
eth0: Broadcom 4400 10/100BaseT Ethernet 00:16:d4:54:64:8f
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
input: PC Speaker as /class/input/input3
intel_rng: FWH not detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:06:04.2 [1524:0550] (rev 1)
PCI: Enabling device 0000:06:04.2 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:04.2[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:06:04.2 to 64
mmc0: SDHCI at 0xd2003400 irq 17 DMA
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
floppy0: no floppy controllers found
lp: driver loaded but no devices found
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ACPI: AC Adapter [ACAD] (off-line)
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [SLPB]
input: Power Button (CM) as /class/input/input7
ACPI: Power Button (CM) [PWRB]
No dock devices found.
ibm_acpi: ec object not found
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda5, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.2.0d
ipw3945: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:05:00.0 to 64
ipw3945: Detected Intel PRO/Wireless 3945ABG Network Connection
ipw3945: Detected geography ABG (13 802.11bg channels, 23 802.11a channels)
ieee80211_crypt: registered algorithm 'WEP'
ADDRCONF(NETDEV_UP): eth1: link is not ready
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
eth1: no IPv6 routers present
atkbd.c: Unknown key pressed (translated set 2, code 0xb4 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xb4 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xb4 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xb4 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: PCI probing failure in 2.6.21-rc3
2007-03-15 19:06 ` Andrew Morton
2007-03-15 21:06 ` Francis Moreau
@ 2007-03-21 12:32 ` Francis Moreau
2007-03-23 22:49 ` Greg KH
2 siblings, 0 replies; 5+ messages in thread
From: Francis Moreau @ 2007-03-21 12:32 UTC (permalink / raw)
To: Andrew Morton; +Cc: linux-kernel, Greg KH, bunk
Andrew,
[ cc'ed Adrian, since he might be interested to track this out ]
On 3/15/07, Andrew Morton <akpm@linux-foundation.org> wrote:
> Greg, could we please either
>
> a) start doing something about these reports or
> b) publish sufficient info to permit others to do something about these
> reports or
> c) remove the printk?
>
What am I suppose to do at this point ?
I'm sorry but I have no knowledge to sort it out by myself. Is this a
real bug or just noises that I should discard ? Should I fill a bug
report ?
Thanks
--
Francis
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: PCI probing failure in 2.6.21-rc3
2007-03-15 19:06 ` Andrew Morton
2007-03-15 21:06 ` Francis Moreau
2007-03-21 12:32 ` Francis Moreau
@ 2007-03-23 22:49 ` Greg KH
2 siblings, 0 replies; 5+ messages in thread
From: Greg KH @ 2007-03-23 22:49 UTC (permalink / raw)
To: Andrew Morton, bk; +Cc: Francis Moreau, linux-kernel
On Thu, Mar 15, 2007 at 11:06:47AM -0800, Andrew Morton wrote:
> > On Wed, 14 Mar 2007 09:47:42 +0100 "Francis Moreau" <francis.moro@gmail.com> wrote:
> > I already posted this issue but it was on a 2.6.19.7 kernel
> > (2.6.19-1.2911.6.5.fc6 to be accurate). So it doesn't seem to be a
> > regression.
> >
> > During boot the console shows up this:
> >
> > [...]
> > PCI: Probing PCI hardware (bus 00)
> > PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
> > PCI quirk: region 1180-11bf claimed by ICH6 GPIO
> > 0000:00:1f.2: trying to change BAR0 from 0000 to 01F0
> > 0000:00:1f.2: trying to change BAR1 from 0000 to 03F4
> > 0000:00:1f.2: trying to change BAR2 from 0000 to 0170
> > 0000:00:1f.2: trying to change BAR3 from 0000 to 0374
> > Boot video device is 0000:01:00.0
> > PCI: Transparent bridge - 0000:00:1e.0
> > PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06 (-#07)
> > (try 'pci=assign-busses')
> > Please report the result to linux-kernel to fix this permanently
> > [...]
> >
> > I haven't time to test 'pci=assign-busses' option, I'll do it later,
> > but I wanted to report this ASAP.
>
> Greg, could we please either
>
> a) start doing something about these reports or
> b) publish sufficient info to permit others to do something about these
> reports or
> c) remove the printk?
Ugh, I'm getting really tired of it too. Bernhard, any plans on
addressing these constant reports? You sent me this patch and then seem
to have disappered when dealing with the fallout of the different
messages :(
Should I just revert your original patch all-together?
thanks,
greg k-h
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2007-03-23 23:08 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-03-14 8:47 PCI probing failure in 2.6.21-rc3 Francis Moreau
2007-03-15 19:06 ` Andrew Morton
2007-03-15 21:06 ` Francis Moreau
2007-03-21 12:32 ` Francis Moreau
2007-03-23 22:49 ` Greg KH
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox