* [patch 1/5] 53c700 scsi: m68k support for the 53c700 SCSI core
2007-06-17 12:47 [patch 0/5] m68k 53c700 SCSI Geert Uytterhoeven
@ 2007-06-17 12:47 ` Geert Uytterhoeven
2007-06-17 12:47 ` [patch 2/5] 53c700 scsi: m68k BVME6000 NCR53C710 SCSI Geert Uytterhoeven
` (5 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Geert Uytterhoeven @ 2007-06-17 12:47 UTC (permalink / raw)
To: James E.J. Bottomley
Cc: Matthew Wilcox, Christoph Hellwig, Kars de Jong, Richard Hirst,
linux-scsi, linux-kernel, linux-m68k
[-- Attachment #1: m68k-53c700-core.diff --]
[-- Type: text/plain, Size: 5874 bytes --]
From: Kars de Jong <jongk@linux-m68k.org>
Add m68k support to the 53c700 SCSI driver
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
drivers/scsi/53c700.c | 20 ++++++++++----------
drivers/scsi/53c700.h | 5 +++++
drivers/scsi/Kconfig | 13 +++++--------
3 files changed, 20 insertions(+), 18 deletions(-)
--- a/drivers/scsi/53c700.c
+++ b/drivers/scsi/53c700.c
@@ -653,7 +653,6 @@ NCR_700_chip_setup(struct Scsi_Host *hos
{
struct NCR_700_Host_Parameters *hostdata =
(struct NCR_700_Host_Parameters *)host->hostdata[0];
- __u32 dcntl_extra = 0;
__u8 min_period;
__u8 min_xferp = (hostdata->chip710 ? NCR_710_MIN_XFERP : NCR_700_MIN_XFERP);
@@ -678,13 +677,14 @@ NCR_700_chip_setup(struct Scsi_Host *hos
burst_disable = BURST_DISABLE;
break;
}
- dcntl_extra = COMPAT_700_MODE;
+ hostdata->dcntl_extra |= COMPAT_700_MODE;
- NCR_700_writeb(dcntl_extra, host, DCNTL_REG);
+ NCR_700_writeb(hostdata->dcntl_extra, host, DCNTL_REG);
NCR_700_writeb(burst_length | hostdata->dmode_extra,
host, DMODE_710_REG);
- NCR_700_writeb(burst_disable | (hostdata->differential ?
- DIFF : 0), host, CTEST7_REG);
+ NCR_700_writeb(burst_disable | hostdata->ctest7_extra |
+ (hostdata->differential ? DIFF : 0),
+ host, CTEST7_REG);
NCR_700_writeb(BTB_TIMER_DISABLE, host, CTEST0_REG);
NCR_700_writeb(FULL_ARBITRATION | ENABLE_PARITY | PARITY
| AUTO_ATN, host, SCNTL0_REG);
@@ -719,13 +719,13 @@ NCR_700_chip_setup(struct Scsi_Host *hos
* of spec: sync divider 2, async divider 3 */
DEBUG(("53c700: sync 2 async 3\n"));
NCR_700_writeb(SYNC_DIV_2_0, host, SBCL_REG);
- NCR_700_writeb(ASYNC_DIV_3_0 | dcntl_extra, host, DCNTL_REG);
+ NCR_700_writeb(ASYNC_DIV_3_0 | hostdata->dcntl_extra, host, DCNTL_REG);
hostdata->sync_clock = hostdata->clock/2;
} else if(hostdata->clock > 50 && hostdata->clock <= 75) {
/* sync divider 1.5, async divider 3 */
DEBUG(("53c700: sync 1.5 async 3\n"));
NCR_700_writeb(SYNC_DIV_1_5, host, SBCL_REG);
- NCR_700_writeb(ASYNC_DIV_3_0 | dcntl_extra, host, DCNTL_REG);
+ NCR_700_writeb(ASYNC_DIV_3_0 | hostdata->dcntl_extra, host, DCNTL_REG);
hostdata->sync_clock = hostdata->clock*2;
hostdata->sync_clock /= 3;
@@ -733,18 +733,18 @@ NCR_700_chip_setup(struct Scsi_Host *hos
/* sync divider 1, async divider 2 */
DEBUG(("53c700: sync 1 async 2\n"));
NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG);
- NCR_700_writeb(ASYNC_DIV_2_0 | dcntl_extra, host, DCNTL_REG);
+ NCR_700_writeb(ASYNC_DIV_2_0 | hostdata->dcntl_extra, host, DCNTL_REG);
hostdata->sync_clock = hostdata->clock;
} else if(hostdata->clock > 25 && hostdata->clock <=37) {
/* sync divider 1, async divider 1.5 */
DEBUG(("53c700: sync 1 async 1.5\n"));
NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG);
- NCR_700_writeb(ASYNC_DIV_1_5 | dcntl_extra, host, DCNTL_REG);
+ NCR_700_writeb(ASYNC_DIV_1_5 | hostdata->dcntl_extra, host, DCNTL_REG);
hostdata->sync_clock = hostdata->clock;
} else {
DEBUG(("53c700: sync 1 async 1\n"));
NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG);
- NCR_700_writeb(ASYNC_DIV_1_0 | dcntl_extra, host, DCNTL_REG);
+ NCR_700_writeb(ASYNC_DIV_1_0 | hostdata->dcntl_extra, host, DCNTL_REG);
/* sync divider 1, async divider 1 */
hostdata->sync_clock = hostdata->clock;
}
--- a/drivers/scsi/53c700.h
+++ b/drivers/scsi/53c700.h
@@ -177,6 +177,7 @@ struct NCR_700_command_slot {
__u8 state;
#define NCR_700_FLAG_AUTOSENSE 0x01
__u8 flags;
+ __u8 pad1[2]; /* Needed for m68k where min alignment is 2 bytes */
int tag;
__u32 resume_offset;
struct scsi_cmnd *cmnd;
@@ -196,6 +197,8 @@ struct NCR_700_Host_Parameters {
void __iomem *base; /* the base for the port (copied to host) */
struct device *dev;
__u32 dmode_extra; /* adjustable bus settings */
+ __u32 dcntl_extra; /* adjustable bus settings */
+ __u32 ctest7_extra; /* adjustable bus settings */
__u32 differential:1; /* if we are differential */
#ifdef CONFIG_53C700_LE_ON_BE
/* This option is for HP only. Set it if your chip is wired for
@@ -352,6 +355,7 @@ struct NCR_700_Host_Parameters {
#define SEL_TIMEOUT_DISABLE 0x10 /* 710 only */
#define DFP 0x08
#define EVP 0x04
+#define CTEST7_TT1 0x02
#define DIFF 0x01
#define CTEST6_REG 0x1A
#define TEMP_REG 0x1C
@@ -385,6 +389,7 @@ struct NCR_700_Host_Parameters {
#define SOFTWARE_RESET 0x01
#define COMPAT_700_MODE 0x01
#define SCRPTS_16BITS 0x20
+#define EA_710 0x20
#define ASYNC_DIV_2_0 0x00
#define ASYNC_DIV_1_5 0x40
#define ASYNC_DIV_1_0 0x80
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -1006,6 +1006,11 @@ config SCSI_STEX
To compile this driver as a module, choose M here: the
module will be called stex.
+config 53C700_BE_BUS
+ bool
+ depends on M68K
+ default y
+
config SCSI_SYM53C8XX_2
tristate "SYM53C8XX Version 2 SCSI support"
depends on PCI && SCSI
@@ -1728,14 +1733,6 @@ config BVME6000_SCSI
SCSI controller chip. Almost everyone using one of these boards
will want to say Y to this question.
-config SCSI_NCR53C7xx_FAST
- bool "allow FAST-SCSI [10MHz]"
- depends on SCSI_AMIGA7XX || MVME16x_SCSI || BVME6000_SCSI
- help
- This will enable 10MHz FAST-SCSI transfers with your host
- adapter. Some systems have problems with that speed, so it's safest
- to say N here.
-
config SUN3_SCSI
tristate "Sun3 NCR5380 SCSI"
depends on SUN3 && SCSI
--
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 8+ messages in thread* [patch 2/5] 53c700 scsi: m68k BVME6000 NCR53C710 SCSI
2007-06-17 12:47 [patch 0/5] m68k 53c700 SCSI Geert Uytterhoeven
2007-06-17 12:47 ` [patch 1/5] 53c700 scsi: m68k support for the 53c700 SCSI core Geert Uytterhoeven
@ 2007-06-17 12:47 ` Geert Uytterhoeven
2007-06-17 12:47 ` [patch 3/5] 53c700 scsi: m68k MVME16x " Geert Uytterhoeven
` (4 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Geert Uytterhoeven @ 2007-06-17 12:47 UTC (permalink / raw)
To: James E.J. Bottomley
Cc: Matthew Wilcox, Christoph Hellwig, Kars de Jong, Richard Hirst,
linux-scsi, linux-kernel, linux-m68k
[-- Attachment #1: m68k-53c700-bvme6000.diff --]
[-- Type: text/plain, Size: 5239 bytes --]
From: Kars de Jong <jongk@linux-m68k.org>
New driver for the BVME6000 NCR53C710 SCSI controller, using the 53c700 SCSI
core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
drivers/scsi/Kconfig | 6 -
drivers/scsi/Makefile | 1
drivers/scsi/bvme6000_scsi.c | 135 +++++++++++++++++++++++++++++++++++++++++++
3 files changed, 139 insertions(+), 3 deletions(-)
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -1008,7 +1008,7 @@ config SCSI_STEX
config 53C700_BE_BUS
bool
- depends on M68K
+ depends on BVME6000_SCSI
default y
config SCSI_SYM53C8XX_2
@@ -1725,8 +1725,8 @@ config MVME16x_SCSI
will want to say Y to this question.
config BVME6000_SCSI
- bool "NCR53C710 SCSI driver for BVME6000"
- depends on BVME6000 && SCSI && BROKEN
+ tristate "NCR53C710 SCSI driver for BVME6000"
+ depends on BVME6000 && SCSI
select SCSI_SPI_ATTRS
help
The BVME4000 and BVME6000 boards from BVM Ltd use the NCR53C710
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -52,6 +52,7 @@ obj-$(CONFIG_ATARI_SCSI) += atari_scsi.o
obj-$(CONFIG_MAC_SCSI) += mac_scsi.o
obj-$(CONFIG_SCSI_MAC_ESP) += mac_esp.o NCR53C9x.o
obj-$(CONFIG_SUN3_SCSI) += sun3_scsi.o sun3_scsi_vme.o
+obj-$(CONFIG_BVME6000_SCSI) += 53c700.o bvme6000_scsi.o
obj-$(CONFIG_SCSI_SIM710) += 53c700.o sim710.o
obj-$(CONFIG_SCSI_ADVANSYS) += advansys.o
obj-$(CONFIG_SCSI_PSI240I) += psi240i.o
--- /dev/null
+++ b/drivers/scsi/bvme6000_scsi.c
@@ -0,0 +1,135 @@
+/*
+ * Detection routine for the NCR53c710 based BVME6000 SCSI Controllers for Linux.
+ *
+ * Based on work by Alan Hourihane and Kars de Jong
+ *
+ * Rewritten to use 53c700.c by Richard Hirst <richard@sleepie.demon.co.uk>
+ */
+
+#include <linux/module.h>
+#include <linux/blkdev.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <asm/bvme6000hw.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_device.h>
+#include <scsi/scsi_transport.h>
+#include <scsi/scsi_transport_spi.h>
+
+#include "53c700.h"
+
+MODULE_AUTHOR("Richard Hirst <richard@sleepie.demon.co.uk>");
+MODULE_DESCRIPTION("BVME6000 NCR53C710 driver");
+MODULE_LICENSE("GPL");
+
+static struct scsi_host_template bvme6000_scsi_driver_template = {
+ .name = "BVME6000 NCR53c710 SCSI",
+ .proc_name = "BVME6000",
+ .this_id = 7,
+ .module = THIS_MODULE,
+};
+
+static struct platform_device *bvme6000_scsi_device;
+
+static __devinit int
+bvme6000_probe(struct device *dev)
+{
+ struct Scsi_Host * host = NULL;
+ struct NCR_700_Host_Parameters *hostdata;
+
+ if (!MACH_IS_BVME6000)
+ goto out;
+
+ hostdata = kmalloc(sizeof(struct NCR_700_Host_Parameters), GFP_KERNEL);
+ if (hostdata == NULL) {
+ printk(KERN_ERR "bvme6000-scsi: "
+ "Failed to allocate host data\n");
+ goto out;
+ }
+ memset(hostdata, 0, sizeof(struct NCR_700_Host_Parameters));
+
+ /* Fill in the required pieces of hostdata */
+ hostdata->base = (void __iomem *)BVME_NCR53C710_BASE;
+ hostdata->clock = 40; /* XXX - depends on the CPU clock! */
+ hostdata->chip710 = 1;
+ hostdata->dmode_extra = DMODE_FC2;
+ hostdata->dcntl_extra = EA_710;
+ hostdata->ctest7_extra = CTEST7_TT1;
+
+ /* and register the chip */
+ host = NCR_700_detect(&bvme6000_scsi_driver_template, hostdata, dev);
+ if (!host) {
+ printk(KERN_ERR "bvme6000-scsi: No host detected; "
+ "board configuration problem?\n");
+ goto out_free;
+ }
+ host->base = BVME_NCR53C710_BASE;
+ host->this_id = 7;
+ host->irq = BVME_IRQ_SCSI;
+ if (request_irq(BVME_IRQ_SCSI, NCR_700_intr, 0, "bvme6000-scsi",
+ host)) {
+ printk(KERN_ERR "bvme6000-scsi: request_irq failed\n");
+ goto out_put_host;
+ }
+
+ scsi_scan_host(host);
+
+ return 0;
+
+ out_put_host:
+ scsi_host_put(host);
+ out_free:
+ kfree(hostdata);
+ out:
+ return -ENODEV;
+}
+
+static __devexit int
+bvme6000_device_remove(struct device *dev)
+{
+ struct Scsi_Host *host = dev_to_shost(dev);
+ struct NCR_700_Host_Parameters *hostdata = shost_priv(host);
+
+ scsi_remove_host(host);
+ NCR_700_release(host);
+ kfree(hostdata);
+ free_irq(host->irq, host);
+
+ return 0;
+}
+
+static struct device_driver bvme6000_scsi_driver = {
+ .name = "bvme6000-scsi",
+ .bus = &platform_bus_type,
+ .probe = bvme6000_probe,
+ .remove = __devexit_p(bvme6000_device_remove),
+};
+
+static int __init bvme6000_scsi_init(void)
+{
+ int err;
+
+ err = driver_register(&bvme6000_scsi_driver);
+ if (err) {
+ return err;
+
+ bvme6000_scsi_device = platform_device_register_simple("bvme6000-scsi",
+ -1, NULL, 0);
+ if (IS_ERR(bvme6000_scsi_device)) {
+ driver_unregister(&bvme6000_scsi_driver);
+ return PTR_ERR(bvme6000_scsi_device);
+ }
+
+ return 0;
+}
+
+static void __exit bvme6000_scsi_exit(void)
+{
+ platform_device_unregister(bvme6000_scsi_device);
+ driver_unregister(&bvme6000_scsi_driver);
+}
+
+module_init(bvme6000_scsi_init);
+module_exit(bvme6000_scsi_exit);
--
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 8+ messages in thread* [patch 3/5] 53c700 scsi: m68k MVME16x NCR53C710 SCSI
2007-06-17 12:47 [patch 0/5] m68k 53c700 SCSI Geert Uytterhoeven
2007-06-17 12:47 ` [patch 1/5] 53c700 scsi: m68k support for the 53c700 SCSI core Geert Uytterhoeven
2007-06-17 12:47 ` [patch 2/5] 53c700 scsi: m68k BVME6000 NCR53C710 SCSI Geert Uytterhoeven
@ 2007-06-17 12:47 ` Geert Uytterhoeven
2007-06-17 12:47 ` [patch 4/5] 53c700 scsi: Amiga 4000T NCR53c710 SCSI Geert Uytterhoeven
` (3 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Geert Uytterhoeven @ 2007-06-17 12:47 UTC (permalink / raw)
To: James E.J. Bottomley
Cc: Matthew Wilcox, Christoph Hellwig, Kars de Jong, Richard Hirst,
linux-scsi, linux-kernel, linux-m68k
[-- Attachment #1: m68k-53c700-mvme16x.diff --]
[-- Type: text/plain, Size: 5691 bytes --]
From: Kars de Jong <jongk@linux-m68k.org>
New driver for the MVME16x NCR53C710 SCSI controller, using the 53c700 SCSI
core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
drivers/scsi/Kconfig | 6 -
drivers/scsi/Makefile | 1
drivers/scsi/mvme16x_scsi.c | 158 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 162 insertions(+), 3 deletions(-)
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -1008,7 +1008,7 @@ config SCSI_STEX
config 53C700_BE_BUS
bool
- depends on BVME6000_SCSI
+ depends on MVME16x_SCSI || BVME6000_SCSI
default y
config SCSI_SYM53C8XX_2
@@ -1716,8 +1716,8 @@ config MVME147_SCSI
single-board computer.
config MVME16x_SCSI
- bool "NCR53C710 SCSI driver for MVME16x"
- depends on MVME16x && SCSI && BROKEN
+ tristate "NCR53C710 SCSI driver for MVME16x"
+ depends on MVME16x && SCSI
select SCSI_SPI_ATTRS
help
The Motorola MVME162, 166, 167, 172 and 177 boards use the NCR53C710
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -52,6 +52,7 @@ obj-$(CONFIG_ATARI_SCSI) += atari_scsi.o
obj-$(CONFIG_MAC_SCSI) += mac_scsi.o
obj-$(CONFIG_SCSI_MAC_ESP) += mac_esp.o NCR53C9x.o
obj-$(CONFIG_SUN3_SCSI) += sun3_scsi.o sun3_scsi_vme.o
+obj-$(CONFIG_MVME16x_SCSI) += 53c700.o mvme16x_scsi.o
obj-$(CONFIG_BVME6000_SCSI) += 53c700.o bvme6000_scsi.o
obj-$(CONFIG_SCSI_SIM710) += 53c700.o sim710.o
obj-$(CONFIG_SCSI_ADVANSYS) += advansys.o
--- /dev/null
+++ b/drivers/scsi/mvme16x_scsi.c
@@ -0,0 +1,158 @@
+/*
+ * Detection routine for the NCR53c710 based MVME16x SCSI Controllers for Linux.
+ *
+ * Based on work by Alan Hourihane
+ *
+ * Rewritten to use 53c700.c by Kars de Jong <jongk@linux-m68k.org>
+ */
+
+#include <linux/module.h>
+#include <linux/blkdev.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <asm/mvme16xhw.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_device.h>
+#include <scsi/scsi_transport.h>
+#include <scsi/scsi_transport_spi.h>
+
+#include "53c700.h"
+
+MODULE_AUTHOR("Kars de Jong <jongk@linux-m68k.org>");
+MODULE_DESCRIPTION("MVME16x NCR53C710 driver");
+MODULE_LICENSE("GPL");
+
+static struct scsi_host_template mvme16x_scsi_driver_template = {
+ .name = "MVME16x NCR53c710 SCSI",
+ .proc_name = "MVME16x",
+ .this_id = 7,
+ .module = THIS_MODULE,
+};
+
+static struct platform_device *mvme16x_scsi_device;
+
+static __devinit int
+mvme16x_probe(struct device *dev)
+{
+ struct Scsi_Host * host = NULL;
+ struct NCR_700_Host_Parameters *hostdata;
+
+ if (!MACH_IS_MVME16x)
+ goto out;
+
+ if (mvme16x_config & MVME16x_CONFIG_NO_SCSICHIP) {
+ printk(KERN_INFO "mvme16x-scsi: detection disabled, "
+ "SCSI chip not present\n");
+ goto out;
+ }
+
+ hostdata = kmalloc(sizeof(struct NCR_700_Host_Parameters), GFP_KERNEL);
+ if (hostdata == NULL) {
+ printk(KERN_ERR "mvme16x-scsi: "
+ "Failed to allocate host data\n");
+ goto out;
+ }
+ memset(hostdata, 0, sizeof(struct NCR_700_Host_Parameters));
+
+ /* Fill in the required pieces of hostdata */
+ hostdata->base = (void __iomem *)0xfff47000UL;
+ hostdata->clock = 50; /* XXX - depends on the CPU clock! */
+ hostdata->chip710 = 1;
+ hostdata->dmode_extra = DMODE_FC2;
+ hostdata->dcntl_extra = EA_710;
+ hostdata->ctest7_extra = CTEST7_TT1;
+
+ /* and register the chip */
+ host = NCR_700_detect(&mvme16x_scsi_driver_template, hostdata, dev);
+ if (!host) {
+ printk(KERN_ERR "mvme16x-scsi: No host detected; "
+ "board configuration problem?\n");
+ goto out_free;
+ }
+ host->this_id = 7;
+ host->base = 0xfff47000UL;
+ host->irq = MVME16x_IRQ_SCSI;
+ if (request_irq(host->irq, NCR_700_intr, 0, "mvme16x-scsi", host)) {
+ printk(KERN_ERR "mvme16x-scsi: request_irq failed\n");
+ goto out_put_host;
+ }
+
+ /* Enable scsi chip ints */
+ {
+ volatile unsigned long v;
+
+ /* Enable scsi interrupts at level 4 in PCCchip2 */
+ v = in_be32(0xfff4202c);
+ v = (v & ~0xff) | 0x10 | 4;
+ out_be32(0xfff4202c, v);
+ }
+
+ scsi_scan_host(host);
+
+ return 0;
+
+ out_put_host:
+ scsi_host_put(host);
+ out_free:
+ kfree(hostdata);
+ out:
+ return -ENODEV;
+}
+
+static __devexit int
+mvme16x_device_remove(struct device *dev)
+{
+ struct Scsi_Host *host = dev_to_shost(dev);
+ struct NCR_700_Host_Parameters *hostdata = shost_priv(host);
+
+ /* Disable scsi chip ints */
+ {
+ volatile unsigned long v;
+
+ v = in_be32(0xfff4202c);
+ v &= ~0x10;
+ out_be32(0xfff4202c, v);
+ }
+ scsi_remove_host(host);
+ NCR_700_release(host);
+ kfree(hostdata);
+ free_irq(host->irq, host);
+
+ return 0;
+}
+
+static struct device_driver mvme16x_scsi_driver = {
+ .name = "mvme16x-scsi",
+ .bus = &platform_bus_type,
+ .probe = mvme16x_probe,
+ .remove = __devexit_p(mvme16x_device_remove),
+};
+
+static int __init mvme16x_scsi_init(void)
+{
+ int err;
+
+ err = driver_register(&mvme16x_scsi_driver);
+ if (err)
+ return err;
+
+ mvme16x_scsi_device = platform_device_register_simple("mvme16x-scsi",
+ -1, NULL, 0);
+ if (IS_ERR(mvme16x_scsi_device)) {
+ driver_unregister(&mvme16x_scsi_driver);
+ return PTR_ERR(mvme16x_scsi_device);
+ }
+
+ return 0;
+}
+
+static void __exit mvme16x_scsi_exit(void)
+{
+ platform_device_unregister(mvme16x_scsi_device);
+ driver_unregister(&mvme16x_scsi_driver);
+}
+
+module_init(mvme16x_scsi_init);
+module_exit(mvme16x_scsi_exit);
--
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 8+ messages in thread* [patch 4/5] 53c700 scsi: Amiga 4000T NCR53c710 SCSI
2007-06-17 12:47 [patch 0/5] m68k 53c700 SCSI Geert Uytterhoeven
` (2 preceding siblings ...)
2007-06-17 12:47 ` [patch 3/5] 53c700 scsi: m68k MVME16x " Geert Uytterhoeven
@ 2007-06-17 12:47 ` Geert Uytterhoeven
2007-06-17 12:47 ` [patch 5/5] 53c700 scsi: Amiga Zorro " Geert Uytterhoeven
` (2 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Geert Uytterhoeven @ 2007-06-17 12:47 UTC (permalink / raw)
To: James E.J. Bottomley
Cc: Matthew Wilcox, Christoph Hellwig, Kars de Jong, Richard Hirst,
linux-scsi, linux-kernel, linux-m68k
[-- Attachment #1: m68k-53c700-a4000t.diff --]
[-- Type: text/plain, Size: 6041 bytes --]
From: Kars de Jong <jongk@linux-m68k.org>
New driver for the Amiga 4000T built-in NCR53c710 SCSI controller, using the
53c700 SCSI core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
drivers/scsi/Kconfig | 14 ++++
drivers/scsi/Makefile | 1
drivers/scsi/a4000t.c | 142 ++++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 155 insertions(+), 2 deletions(-)
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -1008,7 +1008,7 @@ config SCSI_STEX
config 53C700_BE_BUS
bool
- depends on MVME16x_SCSI || BVME6000_SCSI
+ depends on SCSI_A4000T || MVME16x_SCSI || BVME6000_SCSI
default y
config SCSI_SYM53C8XX_2
@@ -1615,13 +1615,23 @@ config FASTLANE_SCSI
If you have the Phase5 Fastlane Z3 SCSI controller, or plan to use
one in the near future, say Y to this question. Otherwise, say N.
+config SCSI_A4000T
+ tristate "A4000T NCR53c710 SCSI support (EXPERIMENTAL)"
+ depends on AMIGA && SCSI && EXPERIMENTAL
+ select SCSI_SPI_ATTRS
+ help
+ If you have an Amiga 4000T and have SCSI devices connected to the
+ built-in SCSI controller, say Y. Otherwise, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called a4000t.
+
config SCSI_AMIGA7XX
bool "Amiga NCR53c710 SCSI support (EXPERIMENTAL)"
depends on AMIGA && SCSI && EXPERIMENTAL && BROKEN
help
Support for various NCR53c710-based SCSI controllers on the Amiga.
This includes:
- - the builtin SCSI controller on the Amiga 4000T,
- the Amiga 4091 Zorro III SCSI-2 controller,
- the MacroSystem Development's WarpEngine Amiga SCSI-2 controller
(info at
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -37,6 +37,7 @@ obj-$(CONFIG_SCSI_SAS_LIBSAS) += libsas/
obj-$(CONFIG_ISCSI_TCP) += libiscsi.o iscsi_tcp.o
obj-$(CONFIG_INFINIBAND_ISER) += libiscsi.o
+obj-$(CONFIG_SCSI_A4000T) += 53c700.o a4000t.o
obj-$(CONFIG_A3000_SCSI) += a3000.o wd33c93.o
obj-$(CONFIG_A2091_SCSI) += a2091.o wd33c93.o
obj-$(CONFIG_GVP11_SCSI) += gvp11.o wd33c93.o
--- /dev/null
+++ b/drivers/scsi/a4000t.c
@@ -0,0 +1,142 @@
+/*
+ * Detection routine for the NCR53c710 based Amiga SCSI Controllers for Linux.
+ * Amiga Technologies A4000T SCSI controller.
+ *
+ * Written 1997 by Alan Hourihane <alanh@fairlite.demon.co.uk>
+ * plus modifications of the 53c7xx.c driver to support the Amiga.
+ *
+ * Rewritten to use 53c700.c by Kars de Jong <jongk@linux-m68k.org>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <asm/amigaints.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_transport_spi.h>
+
+#include "53c700.h"
+
+MODULE_AUTHOR("Alan Hourihane <alanh@fairlite.demon.co.uk> / Kars de Jong <jongk@linux-m68k.org>");
+MODULE_DESCRIPTION("Amiga A4000T NCR53C710 driver");
+MODULE_LICENSE("GPL");
+
+
+static struct scsi_host_template a4000t_scsi_driver_template = {
+ .name = "A4000T builtin SCSI",
+ .proc_name = "A4000t",
+ .this_id = 7,
+ .module = THIS_MODULE,
+};
+
+static struct platform_device *a4000t_scsi_device;
+
+#define A4000T_SCSI_ADDR 0xdd0040
+
+static int __devinit a4000t_probe(struct device *dev)
+{
+ struct Scsi_Host * host = NULL;
+ struct NCR_700_Host_Parameters *hostdata;
+
+ if (!(MACH_IS_AMIGA && AMIGAHW_PRESENT(A4000_SCSI)))
+ goto out;
+
+ if (!request_mem_region(A4000T_SCSI_ADDR, 0x1000,
+ "A4000T builtin SCSI"))
+ goto out;
+
+ hostdata = kmalloc(sizeof(struct NCR_700_Host_Parameters), GFP_KERNEL);
+ if (hostdata == NULL) {
+ printk(KERN_ERR "a4000t-scsi: Failed to allocate host data\n");
+ goto out_release;
+ }
+ memset(hostdata, 0, sizeof(struct NCR_700_Host_Parameters));
+
+ /* Fill in the required pieces of hostdata */
+ hostdata->base = (void __iomem *)ZTWO_VADDR(A4000T_SCSI_ADDR);
+ hostdata->clock = 50;
+ hostdata->chip710 = 1;
+ hostdata->dmode_extra = DMODE_FC2;
+ hostdata->dcntl_extra = EA_710;
+
+ /* and register the chip */
+ host = NCR_700_detect(&a4000t_scsi_driver_template, hostdata, dev);
+ if (!host) {
+ printk(KERN_ERR "a4000t-scsi: No host detected; "
+ "board configuration problem?\n");
+ goto out_free;
+ }
+
+ host->this_id = 7;
+ host->base = A4000T_SCSI_ADDR;
+ host->irq = IRQ_AMIGA_PORTS;
+
+ if (request_irq(host->irq, NCR_700_intr, IRQF_SHARED, "a4000t-scsi",
+ host)) {
+ printk(KERN_ERR "a4000t-scsi: request_irq failed\n");
+ goto out_put_host;
+ }
+
+ scsi_scan_host(host);
+
+ return 0;
+
+ out_put_host:
+ scsi_host_put(host);
+ out_free:
+ kfree(hostdata);
+ out_release:
+ release_mem_region(A4000T_SCSI_ADDR, 0x1000);
+ out:
+ return -ENODEV;
+}
+
+static __devexit int a4000t_device_remove(struct device *dev)
+{
+ struct Scsi_Host *host = dev_to_shost(dev);
+ struct NCR_700_Host_Parameters *hostdata = shost_priv(host);
+
+ scsi_remove_host(host);
+
+ NCR_700_release(host);
+ kfree(hostdata);
+ free_irq(host->irq, host);
+ release_mem_region(A4000T_SCSI_ADDR, 0x1000);
+
+ return 0;
+}
+
+static struct device_driver a4000t_scsi_driver = {
+ .name = "a4000t-scsi",
+ .bus = &platform_bus_type,
+ .probe = a4000t_probe,
+ .remove = __devexit_p(a4000t_device_remove),
+};
+
+static int __init a4000t_scsi_init(void)
+{
+ int err;
+
+ err = driver_register(&a4000t_scsi_driver);
+ if (err)
+ return err;
+
+ a4000t_scsi_device = platform_device_register_simple("a4000t-scsi",
+ -1, NULL, 0);
+ if (IS_ERR(a4000t_scsi_device)) {
+ driver_unregister(&a4000t_scsi_driver);
+ return PTR_ERR(a4000t_scsi_device);
+ }
+
+ return err;
+}
+
+static void __exit a4000t_scsi_exit(void)
+{
+ platform_device_unregister(a4000t_scsi_device);
+ driver_unregister(&a4000t_scsi_driver);
+}
+
+module_init(a4000t_scsi_init);
+module_exit(a4000t_scsi_exit);
--
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 8+ messages in thread* [patch 5/5] 53c700 scsi: Amiga Zorro NCR53c710 SCSI
2007-06-17 12:47 [patch 0/5] m68k 53c700 SCSI Geert Uytterhoeven
` (3 preceding siblings ...)
2007-06-17 12:47 ` [patch 4/5] 53c700 scsi: Amiga 4000T NCR53c710 SCSI Geert Uytterhoeven
@ 2007-06-17 12:47 ` Geert Uytterhoeven
2007-06-19 7:47 ` [patch 0/5] m68k 53c700 SCSI Geert Uytterhoeven
2007-06-19 17:22 ` Christoph Hellwig
6 siblings, 0 replies; 8+ messages in thread
From: Geert Uytterhoeven @ 2007-06-17 12:47 UTC (permalink / raw)
To: James E.J. Bottomley
Cc: Matthew Wilcox, Christoph Hellwig, Kars de Jong, Richard Hirst,
linux-scsi, linux-kernel, linux-m68k
[-- Attachment #1: m68k-53c700-zorro7xx.diff --]
[-- Type: text/plain, Size: 7554 bytes --]
From: Kars de Jong <jongk@linux-m68k.org>
New driver for Amiga Zorro bus NCR53c710 SCSI controllers, using the 53c700
SCSI core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
drivers/scsi/Kconfig | 16 +---
drivers/scsi/Makefile | 1
drivers/scsi/zorro7xx.c | 181 ++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 189 insertions(+), 9 deletions(-)
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -1008,7 +1008,7 @@ config SCSI_STEX
config 53C700_BE_BUS
bool
- depends on SCSI_A4000T || MVME16x_SCSI || BVME6000_SCSI
+ depends on SCSI_A4000T || SCSI_ZORRO7XX || MVME16x_SCSI || BVME6000_SCSI
default y
config SCSI_SYM53C8XX_2
@@ -1626,11 +1626,13 @@ config SCSI_A4000T
To compile this driver as a module, choose M here: the
module will be called a4000t.
-config SCSI_AMIGA7XX
- bool "Amiga NCR53c710 SCSI support (EXPERIMENTAL)"
- depends on AMIGA && SCSI && EXPERIMENTAL && BROKEN
+config SCSI_ZORRO7XX
+ tristate "Zorro NCR53c710 SCSI support (EXPERIMENTAL)"
+ depends on ZORRO && SCSI && EXPERIMENTAL
+ select SCSI_SPI_ATTRS
help
- Support for various NCR53c710-based SCSI controllers on the Amiga.
+ Support for various NCR53c710-based SCSI controllers on Zorro
+ expansion boards for the Amiga.
This includes:
- the Amiga 4091 Zorro III SCSI-2 controller,
- the MacroSystem Development's WarpEngine Amiga SCSI-2 controller
@@ -1639,10 +1641,6 @@ config SCSI_AMIGA7XX
- the SCSI controller on the Phase5 Blizzard PowerUP 603e+
accelerator card for the Amiga 1200,
- the SCSI controller on the GVP Turbo 040/060 accelerator.
- Note that all of the above SCSI controllers, except for the builtin
- SCSI controller on the Amiga 4000T, reside on the Zorro expansion
- bus, so you also have to enable Zorro bus support if you want to use
- them.
config OKTAGON_SCSI
tristate "BSC Oktagon SCSI support (EXPERIMENTAL)"
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_SCSI_SAS_LIBSAS) += libsas/
obj-$(CONFIG_ISCSI_TCP) += libiscsi.o iscsi_tcp.o
obj-$(CONFIG_INFINIBAND_ISER) += libiscsi.o
obj-$(CONFIG_SCSI_A4000T) += 53c700.o a4000t.o
+obj-$(CONFIG_SCSI_ZORRO7XX) += 53c700.o zorro7xx.o
obj-$(CONFIG_A3000_SCSI) += a3000.o wd33c93.o
obj-$(CONFIG_A2091_SCSI) += a2091.o wd33c93.o
obj-$(CONFIG_GVP11_SCSI) += gvp11.o wd33c93.o
--- /dev/null
+++ b/drivers/scsi/zorro7xx.c
@@ -0,0 +1,181 @@
+/*
+ * Detection routine for the NCR53c710 based Amiga SCSI Controllers for Linux.
+ * Amiga MacroSystemUS WarpEngine SCSI controller.
+ * Amiga Technologies/DKB A4091 SCSI controller.
+ *
+ * Written 1997 by Alan Hourihane <alanh@fairlite.demon.co.uk>
+ * plus modifications of the 53c7xx.c driver to support the Amiga.
+ *
+ * Rewritten to use 53c700.c by Kars de Jong <jongk@linux-m68k.org>
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/zorro.h>
+#include <asm/amigaints.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_transport_spi.h>
+
+#include "53c700.h"
+
+MODULE_AUTHOR("Alan Hourihane <alanh@fairlite.demon.co.uk> / Kars de Jong <jongk@linux-m68k.org>");
+MODULE_DESCRIPTION("Amiga Zorro NCR53C710 driver");
+MODULE_LICENSE("GPL");
+
+
+static struct scsi_host_template zorro7xx_scsi_driver_template = {
+ .proc_name = "zorro7xx",
+ .this_id = 7,
+ .module = THIS_MODULE,
+};
+
+static struct zorro_driver_data {
+ const char *name;
+ unsigned long offset;
+ int absolute; /* offset is absolute address */
+} zorro7xx_driver_data[] __devinitdata = {
+ { .name = "PowerUP 603e+", .offset = 0xf40000, .absolute = 1 },
+ { .name = "WarpEngine 40xx", .offset = 0x40000 },
+ { .name = "A4091", .offset = 0x800000 },
+ { .name = "GForce 040/060", .offset = 0x40000 },
+ { 0 }
+};
+
+static struct zorro_device_id zorro7xx_zorro_tbl[] __devinitdata = {
+ {
+ .id = ZORRO_PROD_PHASE5_BLIZZARD_603E_PLUS,
+ .driver_data = (unsigned long)&zorro7xx_driver_data[0],
+ },
+ {
+ .id = ZORRO_PROD_MACROSYSTEMS_WARP_ENGINE_40xx,
+ .driver_data = (unsigned long)&zorro7xx_driver_data[1],
+ },
+ {
+ .id = ZORRO_PROD_CBM_A4091_1,
+ .driver_data = (unsigned long)&zorro7xx_driver_data[2],
+ },
+ {
+ .id = ZORRO_PROD_CBM_A4091_2,
+ .driver_data = (unsigned long)&zorro7xx_driver_data[2],
+ },
+ {
+ .id = ZORRO_PROD_GVP_GFORCE_040_060,
+ .driver_data = (unsigned long)&zorro7xx_driver_data[3],
+ },
+ { 0 }
+};
+MODULE_DEVICE_TABLE(zorro, zorro7xx_zorro_tbl);
+
+static int __devinit zorro7xx_init_one(struct zorro_dev *z,
+ const struct zorro_device_id *ent)
+{
+ struct Scsi_Host * host = NULL;
+ struct NCR_700_Host_Parameters *hostdata;
+ struct zorro_driver_data *zdd;
+ unsigned long board, ioaddr;
+
+ board = zorro_resource_start(z);
+ zdd = (struct zorro_driver_data *)ent->driver_data;
+
+ if (zdd->absolute) {
+ ioaddr = zdd->offset;
+ } else {
+ ioaddr = board + zdd->offset;
+ }
+
+ if (!zorro_request_device(z, zdd->name)) {
+ printk(KERN_ERR "zorro7xx: cannot reserve region 0x%lx, abort\n",
+ board);
+ return -EBUSY;
+ }
+
+ hostdata = kmalloc(sizeof(struct NCR_700_Host_Parameters), GFP_KERNEL);
+ if (hostdata == NULL) {
+ printk(KERN_ERR "zorro7xx: Failed to allocate host data\n");
+ goto out_release;
+ }
+
+ memset(hostdata, 0, sizeof(struct NCR_700_Host_Parameters));
+
+ /* Fill in the required pieces of hostdata */
+ if (ioaddr > 0x01000000)
+ hostdata->base = ioremap(ioaddr, zorro_resource_len(z));
+ else
+ hostdata->base = (void __iomem *)ZTWO_VADDR(ioaddr);
+
+ hostdata->clock = 50;
+ hostdata->chip710 = 1;
+
+ /* Settings for at least WarpEngine 40xx */
+ hostdata->ctest7_extra = CTEST7_TT1;
+
+ zorro7xx_scsi_driver_template.name = zdd->name;
+
+ /* and register the chip */
+ host = NCR_700_detect(&zorro7xx_scsi_driver_template, hostdata,
+ &z->dev);
+ if (!host) {
+ printk(KERN_ERR "zorro7xx: No host detected; "
+ "board configuration problem?\n");
+ goto out_free;
+ }
+
+ host->this_id = 7;
+ host->base = ioaddr;
+ host->irq = IRQ_AMIGA_PORTS;
+
+ if (request_irq(host->irq, NCR_700_intr, IRQF_SHARED, "zorro7xx-scsi",
+ host)) {
+ printk(KERN_ERR "zorro7xx: request_irq failed\n");
+ goto out_put_host;
+ }
+
+ scsi_scan_host(host);
+
+ return 0;
+
+ out_put_host:
+ scsi_host_put(host);
+ out_free:
+ if (ioaddr > 0x01000000)
+ iounmap(hostdata->base);
+ kfree(hostdata);
+ out_release:
+ zorro_release_device(z);
+
+ return -ENODEV;
+}
+
+static __devexit void zorro7xx_remove_one(struct zorro_dev *z)
+{
+ struct Scsi_Host *host = dev_to_shost(&z->dev);
+ struct NCR_700_Host_Parameters *hostdata = shost_priv(host);
+
+ scsi_remove_host(host);
+
+ NCR_700_release(host);
+ kfree(hostdata);
+ free_irq(host->irq, host);
+ zorro_release_device(z);
+}
+
+static struct zorro_driver zorro7xx_driver = {
+ .name = "zorro7xx-scsi",
+ .id_table = zorro7xx_zorro_tbl,
+ .probe = zorro7xx_init_one,
+ .remove = __devexit_p(zorro7xx_remove_one),
+};
+
+static int __init zorro7xx_scsi_init(void)
+{
+ return zorro_register_driver(&zorro7xx_driver);
+}
+
+static void __exit zorro7xx_scsi_exit(void)
+{
+ zorro_unregister_driver(&zorro7xx_driver);
+}
+
+module_init(zorro7xx_scsi_init);
+module_exit(zorro7xx_scsi_exit);
--
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 8+ messages in thread* Re: [patch 0/5] m68k 53c700 SCSI
2007-06-17 12:47 [patch 0/5] m68k 53c700 SCSI Geert Uytterhoeven
` (4 preceding siblings ...)
2007-06-17 12:47 ` [patch 5/5] 53c700 scsi: Amiga Zorro " Geert Uytterhoeven
@ 2007-06-19 7:47 ` Geert Uytterhoeven
2007-06-19 17:22 ` Christoph Hellwig
6 siblings, 0 replies; 8+ messages in thread
From: Geert Uytterhoeven @ 2007-06-19 7:47 UTC (permalink / raw)
To: James E.J. Bottomley
Cc: Matthew Wilcox, Christoph Hellwig, Kars de Jong, Richard Hirst,
linux-scsi, linux-kernel, linux-m68k
Hi James,
On Sun, 17 Jun 2007, Geert Uytterhoeven wrote:
> These patches add support for m68k to the 53c700 SCSI core and introduce new
> drivers for various m68k hardware using this 53c700 SCSI core, to replace the
> just removed drivers using the old 53c7xx SCSI core.
>
> [1] [PATCH] 53c700 scsi: m68k support for the 53c700 SCSI core
> [2] [PATCH] 53c700 scsi: m68k BVME6000 NCR53C710 SCSI
> [3] [PATCH] 53c700 scsi: m68k MVME16x NCR53C710 SCSI
> [4] [PATCH] 53c700 scsi: Amiga 4000T NCR53c710 SCSI
> [5] [PATCH] 53c700 scsi: Amiga Zorro NCR53c710 SCSI
>
> Please apply for 2.6.23. Thx!
Apparently I made some major mistakes when preparing these patches.
Here are the fixes.
---
Fixup m68k 53c700 drivers:
- a4000t.c: Add missing include, needed in some configurations
- bvme6000_scsi.c: Kill bogus opening brace
- zorro7xx.c: Remove MODULE_DEVICE_TABLE, it should be part of another
patch
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
drivers/scsi/a4000t.c | 1 +
drivers/scsi/bvme6000_scsi.c | 2 +-
drivers/scsi/zorro7xx.c | 1 -
3 files changed, 2 insertions(+), 2 deletions(-)
--- a/drivers/scsi/a4000t.c
+++ b/drivers/scsi/a4000t.c
@@ -12,6 +12,7 @@
#include <linux/platform_device.h>
#include <linux/init.h>
#include <linux/interrupt.h>
+#include <asm/amigahw.h>
#include <asm/amigaints.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_transport_spi.h>
--- a/drivers/scsi/bvme6000_scsi.c
+++ b/drivers/scsi/bvme6000_scsi.c
@@ -112,7 +112,7 @@ static int __init bvme6000_scsi_init(voi
int err;
err = driver_register(&bvme6000_scsi_driver);
- if (err) {
+ if (err)
return err;
bvme6000_scsi_device = platform_device_register_simple("bvme6000-scsi",
--- a/drivers/scsi/zorro7xx.c
+++ b/drivers/scsi/zorro7xx.c
@@ -65,7 +65,6 @@ static struct zorro_device_id zorro7xx_z
},
{ 0 }
};
-MODULE_DEVICE_TABLE(zorro, zorro7xx_zorro_tbl);
static int __devinit zorro7xx_init_one(struct zorro_dev *z,
const struct zorro_device_id *ent)
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 8+ messages in thread* Re: [patch 0/5] m68k 53c700 SCSI
2007-06-17 12:47 [patch 0/5] m68k 53c700 SCSI Geert Uytterhoeven
` (5 preceding siblings ...)
2007-06-19 7:47 ` [patch 0/5] m68k 53c700 SCSI Geert Uytterhoeven
@ 2007-06-19 17:22 ` Christoph Hellwig
6 siblings, 0 replies; 8+ messages in thread
From: Christoph Hellwig @ 2007-06-19 17:22 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: James E.J. Bottomley, Matthew Wilcox, Christoph Hellwig,
Kars de Jong, Richard Hirst, linux-scsi, linux-kernel, linux-m68k
On Sun, Jun 17, 2007 at 02:47:04PM +0200, Geert Uytterhoeven wrote:
> Hi James,
>
> These patches add support for m68k to the 53c700 SCSI core and introduce new
> drivers for various m68k hardware using this 53c700 SCSI core, to replace the
> just removed drivers using the old 53c7xx SCSI core.
>
> [1] [PATCH] 53c700 scsi: m68k support for the 53c700 SCSI core
> [2] [PATCH] 53c700 scsi: m68k BVME6000 NCR53C710 SCSI
> [3] [PATCH] 53c700 scsi: m68k MVME16x NCR53C710 SCSI
> [4] [PATCH] 53c700 scsi: Amiga 4000T NCR53c710 SCSI
> [5] [PATCH] 53c700 scsi: Amiga Zorro NCR53c710 SCSI
>
> Please apply for 2.6.23. Thx!
The patches all look very nice to me, thanks a lot.
^ permalink raw reply [flat|nested] 8+ messages in thread