From: "Hans-Jürgen Koch" <hjk@linutronix.de>
To: Andy Herzig <andrew.herzig@ngc.com>
Cc: andrew@sanpeople.com, linux-kernel@vger.kernel.org,
trivial@kernel.org,
linux-arm-kernel <linux-arm-kernel@lists.arm.linux.org.uk>
Subject: Re: [PATCH] at91 pm: Compilation fix for at91sam926x
Date: Thu, 9 Aug 2007 16:53:35 +0200 [thread overview]
Message-ID: <200708091653.35226.hjk@linutronix.de> (raw)
In-Reply-To: <1186661447.6370.19.camel@leoh9-18574.nges.northgrum.com>
(added linux-arm-kernel to CC)
Am Donnerstag 09 August 2007 14:10 schrieb Andy Herzig:
> Hello all,
>
> This patch is intended to fix compilation errors when I tried to add in
> power management to my Atmel AT91SAM9260 board. First, there is no
> separate memory controller in the 9260 as there is in the 9200, so calls
> to do anything with it in pm.c fail.
Correct. I made the same discovery with my AT91SAM9263 board.
>
> Secondly, at91_suspend_entering_slow_clock() is not declared extern by
> drivers that use it. This used to cause only a warning, but in
> 2.6.23-rc1 and beyond, it is an error.
Patch looks good to me. Kernel compiles for my 9263. Didn't test
suspend/resume yet, though.
>
> Signed-off-by: Andrew J. Herzig <andrew.herzig@ngc.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
> ---
> arch/arm/mach-at91/pm.c | 5 ++++-
> drivers/serial/atmel_serial.c | 2 ++
> drivers/usb/gadget/at91_udc.c | 2 ++
> drivers/usb/host/ohci-at91.c | 1 +
> 4 files changed, 9 insertions(+), 1 deletion(-)
>
> diff -uprN -X linux-2.6.23-rc2/Documentation/dontdiff
> linux-2.6.23-rc2-vanilla/arch/arm/mach-at91/pm.c
> linux-2.6.23-rc2/arch/arm/mach-at91/pm.c
> --- linux-2.6.23-rc2-vanilla/arch/arm/mach-at91/pm.c 2007-08-08
> 13:28:37.000000000 -0400
> +++ linux-2.6.23-rc2/arch/arm/mach-at91/pm.c 2007-08-08
> 13:36:43.000000000 -0400
> @@ -176,7 +176,9 @@ static int at91_pm_enter(suspend_state_t
> */
> asm("b 1f; .align 5; 1:");
> asm("mcr p15, 0, r0, c7, c10, 4"); /* drain
> write buffer */
> +#if defined(CONFIG_ARCH_AT91RM9200)
> at91_sys_write(AT91_SDRAMC_SRR, 1); /*
> self-refresh mode */
> +#endif
> /* fall though to next state */
>
> case PM_SUSPEND_ON:
> @@ -218,8 +220,9 @@ static int __init at91_pm_init(void)
> #endif
>
> /* Disable SDRAM low-power mode. Cannot be used with
> self-refresh. */
> +#if defined(CONFIG_ARCH_AT91RM9200)
> at91_sys_write(AT91_SDRAMC_LPR, 0);
> -
> +#endif
> pm_set_ops(&at91_pm_ops);
>
> return 0;
> diff -uprN -X linux-2.6.23-rc2/Documentation/dontdiff
> linux-2.6.23-rc2-vanilla/drivers/serial/atmel_serial.c
> linux-2.6.23-rc2/drivers/serial/atmel_serial.c
> --- linux-2.6.23-rc2-vanilla/drivers/serial/atmel_serial.c
> 2007-08-08 13:28:33.000000000 -0400
> +++ linux-2.6.23-rc2/drivers/serial/atmel_serial.c 2007-08-08
> 13:32:52.000000000 -0400
> @@ -916,6 +916,8 @@ static struct uart_driver atmel_uart = {
> };
>
> #ifdef CONFIG_PM
> +extern int at91_suspend_entering_slow_clock(void);
> +
> static int atmel_serial_suspend(struct platform_device *pdev,
> pm_message_t state)
> {
> struct uart_port *port = platform_get_drvdata(pdev);
> diff -uprN -X linux-2.6.23-rc2/Documentation/dontdiff
> linux-2.6.23-rc2-vanilla/drivers/usb/gadget/at91_udc.c
> linux-2.6.23-rc2/drivers/usb/gadget/at91_udc.c
> --- linux-2.6.23-rc2-vanilla/drivers/usb/gadget/at91_udc.c
> 2007-08-08 13:28:27.000000000 -0400
> +++ linux-2.6.23-rc2/drivers/usb/gadget/at91_udc.c 2007-08-08
> 13:33:21.000000000 -0400
> @@ -1770,6 +1770,8 @@ static int __exit at91udc_remove(struct
> }
>
> #ifdef CONFIG_PM
> +extern int at91_suspend_entering_slow_clock(void);
> +
> static int at91udc_suspend(struct platform_device *pdev, pm_message_t
> mesg)
> {
> struct at91_udc *udc = platform_get_drvdata(pdev);
> diff -uprN -X linux-2.6.23-rc2/Documentation/dontdiff
> linux-2.6.23-rc2-vanilla/drivers/usb/host/ohci-at91.c
> linux-2.6.23-rc2/drivers/usb/host/ohci-at91.c
> --- linux-2.6.23-rc2-vanilla/drivers/usb/host/ohci-at91.c
> 2007-08-08 13:28:27.000000000 -0400
> +++ linux-2.6.23-rc2/drivers/usb/host/ohci-at91.c 2007-08-08
> 13:32:45.000000000 -0400
> @@ -282,6 +282,7 @@ static int ohci_hcd_at91_drv_remove(stru
> }
>
> #ifdef CONFIG_PM
> +extern int at91_suspend_entering_slow_clock(void);
>
> static int
> ohci_hcd_at91_drv_suspend(struct platform_device *pdev, pm_message_t
> mesg)
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
next prev parent reply other threads:[~2007-08-09 14:53 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-08-09 12:10 [PATCH] at91 pm: Compilation fix for at91sam926x Andy Herzig
2007-08-09 14:39 ` Andy Herzig
2007-08-09 14:53 ` Hans-Jürgen Koch [this message]
2007-08-09 16:01 ` Marc Pignat
2007-08-09 17:17 ` Andy Herzig
2007-08-09 18:19 ` Hans-Jürgen Koch
2007-08-09 22:15 ` Ulf Samuelsson
2007-08-10 7:12 ` Hans-Jürgen Koch
2007-08-10 7:33 ` Marc Pignat
[not found] ` <3858727143598039860@unknownmsgid>
2007-08-10 10:00 ` Michel Benoit
2007-08-24 7:11 ` Andrew Victor
2007-08-10 13:54 ` Ulf Samuelsson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200708091653.35226.hjk@linutronix.de \
--to=hjk@linutronix.de \
--cc=andrew.herzig@ngc.com \
--cc=andrew@sanpeople.com \
--cc=linux-arm-kernel@lists.arm.linux.org.uk \
--cc=linux-kernel@vger.kernel.org \
--cc=trivial@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox