From: Andrew Morton <akpm@linux-foundation.org>
To: Christian Volkmann <haveaniceday@cv-sv.de>
Cc: linux-kernel@vger.kernel.org,
Michal Piotrowski <michal.k.k.piotrowski@gmail.com>,
linux-usb-devel@lists.sourceforge.net
Subject: Re: 2.6.23-rc6: usb 1-1: device not accepting address 2, error -62
Date: Sat, 15 Sep 2007 03:48:19 -0700 [thread overview]
Message-ID: <20070915034819.3e695370.akpm@linux-foundation.org> (raw)
In-Reply-To: <46EAFCF7.1030907@cv-sv.de>
Let's cc the USB mailing list.
On Fri, 14 Sep 2007 23:28:23 +0200 Christian Volkmann <haveaniceday@cv-sv.de> wrote:
> Hi everybody,
>
> I have an error message with 2.6.23-rc6.
> This did not happen with 2.6.22.
Another one for Michal's dirt file.
> The kernel reports message like this:
> <3>usb 1-1: device not accepting address 2, error -62
> <3>hub 2-2.1:1.0: hub_port_status failed (err = -71)
>
> Does this message harm or is something broken in 2.6.23-rc6 ?
> I get this kind of messages also with 2.6.23-rc3
Does the machine otherwise work OK?
Even if it does, I don't think we should be (newly) spraying scary messages
like that at people.
> Best regards,
>
> Christian
>
>
> Please see below for:
>
> grep -e hub -e usb boot.msg for a 2.6.23-rc6 boot. (that boot was without (err = -71)
> grep -e hub -e usb boot.msg for a 2.6.22 boot.
> lspci -vnn (2.6.22)
> lsusb -v (2.6.22)
>
>
> 2.6.23-rc6 boot.msg extract ( hub/usb )
>
> <6>usbcore: registered new interface driver usbfs
> <6>usbcore: registered new interface driver hub
> <6>usbcore: registered new device driver usb
> <6>usb usb1: configuration #1 chosen from 1 choice
> <6>hub 1-0:1.0: USB hub found
> <6>hub 1-0:1.0: 2 ports detected
> <6>usb usb2: configuration #1 chosen from 1 choice
> <6>hub 2-0:1.0: USB hub found
> <6>hub 2-0:1.0: 2 ports detected
> <6>usb 1-1: new low speed USB device using ohci_hcd and address 2
> <6>usb usb3: configuration #1 chosen from 1 choice
> <6>hub 3-0:1.0: USB hub found
> <6>hub 3-0:1.0: 2 ports detected
> <6>usb usb4: configuration #1 chosen from 1 choice
> <6>hub 4-0:1.0: USB hub found
> <6>hub 4-0:1.0: 6 ports detected
> <6>usb usb5: configuration #1 chosen from 1 choice
> <6>hub 5-0:1.0: USB hub found
> <6>hub 5-0:1.0: 2 ports detected
> <3>usb 1-1: device not accepting address 2, error -62
> <6>usb 5-2: new full speed USB device using uhci_hcd and address 2
> <6>usb usb6: configuration #1 chosen from 1 choice
> <6>hub 6-0:1.0: USB hub found
> <6>hub 6-0:1.0: 4 ports detected
> <6>usb usb7: configuration #1 chosen from 1 choice
> <6>hub 7-0:1.0: USB hub found
> <6>hub 7-0:1.0: 2 ports detected
> <6>usb 1-1: new low speed USB device using ohci_hcd and address 4
> <6>usb 1-1: configuration #1 chosen from 1 choice
> <6>usb 2-1: new full speed USB device using ohci_hcd and address 2
> <6>usb 2-1: configuration #1 chosen from 1 choice
> <6>usb 6-2: new high speed USB device using ehci_hcd and address 2
> <6>usb 6-2: configuration #1 chosen from 1 choice
> <6>hub 6-2:1.0: USB hub found
> <6>hub 6-2:1.0: 2 ports detected
> <6>usbcore: registered new interface driver hiddev
> <6>input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:03.0-1
> <6>usbcore: registered new interface driver usbhid
> <6>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
> <7>usb-storage: device found at 2
> <7>usb-storage: waiting for device to settle before scanning
> <6>usb 6-2.1: new high speed USB device using ehci_hcd and address 3
> <6>usb 6-2.1: configuration #1 chosen from 1 choice
> <6>hub 6-2.1:1.0: USB hub found
> <6>hub 6-2.1:1.0: 4 ports detected
> <6>usb 6-2.1.1: new high speed USB device using ehci_hcd and address 4
> <6>usb 6-2.1.1: configuration #1 chosen from 1 choice
> <7>usb-storage: device found at 4
> <7>usb-storage: waiting for device to settle before scanning
> <6>usbcore: registered new interface driver usb-storage
> <7>usb-storage: device scan complete
> <7>usb-storage: device scan complete
>
> 2.6.22 boot.msg extract ( hub/usb )
>
> <6>usbcore: registered new interface driver usbfs
> <6>usbcore: registered new interface driver hub
> <6>usbcore: registered new device driver usb
> <6>usb usb1: configuration #1 chosen from 1 choice
> <6>hub 1-0:1.0: USB hub found
> <6>hub 1-0:1.0: 2 ports detected
> <6>usb usb2: configuration #1 chosen from 1 choice
> <6>hub 2-0:1.0: USB hub found
> <6>hub 2-0:1.0: 2 ports detected
> <6>usb 1-1: new low speed USB device using ohci_hcd and address 2
> <6>usb usb3: configuration #1 chosen from 1 choice
> <6>hub 3-0:1.0: USB hub found
> <6>hub 3-0:1.0: 2 ports detected
> <6>usb 1-1: configuration #1 chosen from 1 choice
> <6>usb usb4: configuration #1 chosen from 1 choice
> <6>hub 4-0:1.0: USB hub found
> <6>hub 4-0:1.0: 6 ports detected
> <6>usb 1-1: USB disconnect, address 2
> <6>usb usb5: configuration #1 chosen from 1 choice
> <6>hub 5-0:1.0: USB hub found
> <6>hub 5-0:1.0: 4 ports detected
> <6>usb usb6: configuration #1 chosen from 1 choice
> <6>hub 6-0:1.0: USB hub found
> <6>hub 6-0:1.0: 2 ports detected
> <6>usb usb7: configuration #1 chosen from 1 choice
> <6>hub 7-0:1.0: USB hub found
> <6>hub 7-0:1.0: 2 ports detected
> <6>usb 5-2: new high speed USB device using ehci_hcd and address 2
> <6>usb 5-2: configuration #1 chosen from 1 choice
> <6>hub 5-2:1.0: USB hub found
> <6>hub 5-2:1.0: 2 ports detected
> <6>usb 1-1: new low speed USB device using ohci_hcd and address 3
> <6>usb 1-1: configuration #1 chosen from 1 choice
> <6>usbcore: registered new interface driver hiddev
> <6>usb 2-1: new full speed USB device using ohci_hcd and address 2
> <6>usb 2-1: configuration #1 chosen from 1 choice
> <6>usb 5-2.1: new high speed USB device using ehci_hcd and address 3
> <6>usb 5-2.1: configuration #1 chosen from 1 choice
> <6>hub 5-2.1:1.0: USB hub found
> <6>hub 5-2.1:1.0: 4 ports detected
> <6>input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:03.0-1
> <7>usb-storage: device found at 2
> <7>usb-storage: waiting for device to settle before scanning
> <6>usb 5-2.1.1: new high speed USB device using ehci_hcd and address 4
> <6>usb 5-2.1.1: configuration #1 chosen from 1 choice
> <6>usbcore: registered new interface driver usbhid
> <7>usb-storage: device found at 4
> <7>usb-storage: waiting for device to settle before scanning
> <6>usbcore: registered new interface driver usb-storage
> <6>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
> <7>usb-storage: device scan complete
> <7>usb-storage: device scan complete
>
> [system info snipped ]
>
next prev parent reply other threads:[~2007-09-15 10:48 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-09-14 21:28 2.6.23-rc6: usb 1-1: device not accepting address 2, error -62 Christian Volkmann
2007-09-15 10:48 ` Andrew Morton [this message]
2007-09-15 11:50 ` Christian Volkmann
2007-09-15 12:06 ` Christian Volkmann
2007-09-15 15:31 ` [linux-usb-devel] " Alan Stern
2007-09-15 17:07 ` Christian Volkmann
2007-09-15 19:55 ` Alan Stern
2007-09-15 16:56 ` Pete Zaitcev
2007-09-15 17:11 ` Christian Volkmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20070915034819.3e695370.akpm@linux-foundation.org \
--to=akpm@linux-foundation.org \
--cc=haveaniceday@cv-sv.de \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb-devel@lists.sourceforge.net \
--cc=michal.k.k.piotrowski@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).