* pata_it821x in 2.6.27 - works but no LBA48 and "hdparm -t" is slower
@ 2008-10-18 11:42 Ondrej Zary
2008-10-18 16:30 ` [PATCH] " Ondrej Zary
0 siblings, 1 reply; 3+ messages in thread
From: Ondrej Zary @ 2008-10-18 11:42 UTC (permalink / raw)
To: Alan Cox; +Cc: linux-kernel
Hello,
big thanks to Alan Cox for the work on pata_it821x driver. I just upgraded to 2.6.27
and my RAID1 on IT8212 controller now works without any patching.
Good that I haven't resized my 30GB partition to full drive capacity yet because LBA48
does not work:
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
pata_it821x 0000:00:12.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
pata_it821x: controller in smart mode.
pata_it821x 0000:00:12.0: setting latency timer to 64
pata_it821x: Firmware 02/09/3030
0: MWDMA2 RAID1RAID 0+1 Volume: 0 SAMSUNG HD400LD
1: MWDMA2 RAID1RAID 0+1 Volume: 0 SAMSUNG HD400LD
scsi2 : pata_it821x
scsi3 : pata_it821x
ata3: PATA max UDMA/133 cmd 0x6800 ctl 0x6c00 bmdma 0x7800 irq 11
ata4: PATA max UDMA/133 cmd 0x7000 ctl 0x7400 bmdma 0x7808 irq 11
ata3.00: ATA-4: Integrated Technology Express Inc, , max MWDMA2
ata3.00: 268435455 sectors, multi 0: LBA
^^ no 48 here
ata3.00: RAID1 volume.
ata3.00: configured for DMA
scsi 2:0:0:0: Direct-Access ATA Integrated Techn n/a PQ: 0 ANSI: 5
sd 2:0:0:0: [sdb] 268435455 512-byte hardware sectors (137439 MB)
^^^^^^ should be 400088
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdb] 268435455 512-byte hardware sectors (137439 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4
sd 2:0:0:0: [sdb] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
Also "hdparm -t" is slower (but "hdparm -t --direct" isn't - so it probably isn't pata_it821x issue):
2.6.26 (with my crappy patch):
/dev/sdb:
Timing buffered disk reads: 60 MB in 3.01 seconds = 19.91 MB/sec
/dev/sdb:
Timing O_DIRECT disk reads: 194 MB in 3.00 seconds = 64.62 MB/sec
/dev/sdb:
Model=Integrated Technology Express Inc , FwRev=, SerialNo=▒PX
Config={ }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=no
IORDY=no
PIO modes: pio0
AdvancedPM=no
* signifies the current active mode
2.6.27:
/dev/sdb:
Timing buffered disk reads: 48 MB in 3.08 seconds = 15.57 MB/sec
/dev/sdb:
Timing O_DIRECT disk reads: 196 MB in 3.02 seconds = 64.81 MB/sec
/dev/sdb:
Model=Integrated Technology Express Inc , FwRev=, SerialNo=▒'T
Config={ }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=781422766
IORDY=no
PIO modes: pio0
DMA modes: mdma0 mdma1 mdma2
AdvancedPM=no
Drive conforms to: Unspecified: ATA/ATAPI-0,1,2,3,4
* signifies the current active mode
--
Ondrej Zary
^ permalink raw reply [flat|nested] 3+ messages in thread* [PATCH] Re: pata_it821x in 2.6.27 - works but no LBA48 and "hdparm -t" is slower
2008-10-18 11:42 pata_it821x in 2.6.27 - works but no LBA48 and "hdparm -t" is slower Ondrej Zary
@ 2008-10-18 16:30 ` Ondrej Zary
2008-10-18 17:46 ` Alan Cox
0 siblings, 1 reply; 3+ messages in thread
From: Ondrej Zary @ 2008-10-18 16:30 UTC (permalink / raw)
To: Alan Cox; +Cc: linux-kernel
On Saturday 18 October 2008 13:42:48 Ondrej Zary wrote:
> Hello,
> big thanks to Alan Cox for the work on pata_it821x driver. I just upgraded
> to 2.6.27 and my RAID1 on IT8212 controller now works without any patching.
>
> Good that I haven't resized my 30GB partition to full drive capacity yet
> because LBA48 does not work:
>
> ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
> pata_it821x 0000:00:12.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) ->
> IRQ 11 pata_it821x: controller in smart mode.
> pata_it821x 0000:00:12.0: setting latency timer to 64
> pata_it821x: Firmware 02/09/3030
> 0: MWDMA2 RAID1RAID 0+1 Volume: 0 SAMSUNG HD400LD
> 1: MWDMA2 RAID1RAID 0+1 Volume: 0 SAMSUNG HD400LD
> scsi2 : pata_it821x
> scsi3 : pata_it821x
> ata3: PATA max UDMA/133 cmd 0x6800 ctl 0x6c00 bmdma 0x7800 irq 11
> ata4: PATA max UDMA/133 cmd 0x7000 ctl 0x7400 bmdma 0x7808 irq 11
> ata3.00: ATA-4: Integrated Technology Express Inc, , max MWDMA2
> ata3.00: 268435455 sectors, multi 0: LBA
> ^^ no 48 here
>
> ata3.00: RAID1 volume.
> ata3.00: configured for DMA
> scsi 2:0:0:0: Direct-Access ATA Integrated Techn n/a PQ: 0 ANSI:
> 5 sd 2:0:0:0: [sdb] 268435455 512-byte hardware sectors (137439 MB)
> ^^^^^^ should be
> 400088
>
> sd 2:0:0:0: [sdb] Write Protect is off
> sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't
> support DPO or FUA sd 2:0:0:0: [sdb] 268435455 512-byte hardware sectors
> (137439 MB)
> sd 2:0:0:0: [sdb] Write Protect is off
> sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't
> support DPO or FUA sdb: sdb1 sdb2 sdb3 sdb4
> sd 2:0:0:0: [sdb] Attached SCSI disk
> sd 2:0:0:0: Attached scsi generic sg2 type 0
>
>
> Also "hdparm -t" is slower (but "hdparm -t --direct" isn't - so it probably
> isn't pata_it821x issue): 2.6.26 (with my crappy patch):
> /dev/sdb:
> Timing buffered disk reads: 60 MB in 3.01 seconds = 19.91 MB/sec
>
> /dev/sdb:
> Timing O_DIRECT disk reads: 194 MB in 3.00 seconds = 64.62 MB/sec
>
> /dev/sdb:
>
> Model=Integrated Technology Express Inc , FwRev=, SerialNo=▒PX
> Config={ }
> RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
> BuffType=unknown, BuffSize=0kB, MaxMultSect=0
> (maybe): CurCHS=0/0/0, CurSects=0, LBA=no
> IORDY=no
> PIO modes: pio0
> AdvancedPM=no
>
> * signifies the current active mode
>
> 2.6.27:
> /dev/sdb:
> Timing buffered disk reads: 48 MB in 3.08 seconds = 15.57 MB/sec
>
> /dev/sdb:
> Timing O_DIRECT disk reads: 196 MB in 3.02 seconds = 64.81 MB/sec
>
> /dev/sdb:
>
> Model=Integrated Technology Express Inc , FwRev=, SerialNo=▒'T
> Config={ }
> RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
> BuffType=unknown, BuffSize=0kB, MaxMultSect=0
> (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=781422766
> IORDY=no
> PIO modes: pio0
> DMA modes: mdma0 mdma1 mdma2
> AdvancedPM=no
> Drive conforms to: Unspecified: ATA/ATAPI-0,1,2,3,4
>
> * signifies the current active mode
This patch fixes LBA48 on pata_it821x RAID volumes - and to my surprise, also
increases the "hdparm -t" speed back. Haven't tested access to >128GB area.
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
pata_it821x 0000:00:12.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
pata_it821x: controller in smart mode.
pata_it821x 0000:00:12.0: setting latency timer to 64
pata_it821x: Firmware 02/09/3030
0: MWDMA2 RAID1RAID 0+1 Volume: 0 SAMSUNG HD400LD
1: MWDMA2 RAID1RAID 0+1 Volume: 0 SAMSUNG HD400LD
scsi2 : pata_it821x
scsi3 : pata_it821x
ata3: PATA max UDMA/133 cmd 0x6800 ctl 0x6c00 bmdma 0x7800 irq 11
ata4: PATA max UDMA/133 cmd 0x7000 ctl 0x7400 bmdma 0x7808 irq 11
ata3.00: ATA-4: Integrated Technology Express Inc, , max MWDMA2
ata3.00: 781422766 sectors, multi 0: LBA48
ata3.00: RAID1 volume.
ata3.00: configured for DMA
scsi 2:0:0:0: Direct-Access ATA Integrated Techn n/a PQ: 0 ANSI: 5
sd 2:0:0:0: [sdb] 781422766 512-byte hardware sectors (400088 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdb] 781422766 512-byte hardware sectors (400088 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4
sd 2:0:0:0: [sdb] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
/dev/sdb:
Timing buffered disk reads: 60 MB in 3.01 seconds = 19.91 MB/sec
Fix LBA48 on pata_it821x RAID volumes.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
--- linux-2.6.27-orig/drivers/ata/pata_it821x.c 2008-10-18 17:09:07.000000000 +0200
+++ linux-2.6.27-pentium/drivers/ata/pata_it821x.c 2008-10-18 17:10:24.000000000 +0200
@@ -557,9 +557,8 @@
if (strstr(model_num, "Integrated Technology Express")) {
/* Set feature bits the firmware neglects */
id[49] |= 0x0300; /* LBA, DMA */
- id[82] |= 0x0400; /* LBA48 */
id[83] &= 0x7FFF;
- id[83] |= 0x4000; /* Word 83 is valid */
+ id[83] |= 0x4400; /* Word 83 is valid and LBA48 */
id[86] |= 0x0400; /* LBA48 on */
id[ATA_ID_MAJOR_VER] |= 0x1F;
}
--
Ondrej Zary
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [PATCH] Re: pata_it821x in 2.6.27 - works but no LBA48 and "hdparm -t" is slower
2008-10-18 16:30 ` [PATCH] " Ondrej Zary
@ 2008-10-18 17:46 ` Alan Cox
0 siblings, 0 replies; 3+ messages in thread
From: Alan Cox @ 2008-10-18 17:46 UTC (permalink / raw)
To: Ondrej Zary; +Cc: linux-kernel, jeff
On Sat, 18 Oct 2008 18:30:37 +0200
Ondrej Zary <linux@rainbow-software.org> wrote:
> This patch fixes LBA48 on pata_it821x RAID volumes - and to my surprise, also
> increases the "hdparm -t" speed back. Haven't tested access to >128GB area.
>
> ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
> pata_it821x 0000:00:12.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
> pata_it821x: controller in smart mode.
> pata_it821x 0000:00:12.0: setting latency timer to 64
> pata_it821x: Firmware 02/09/3030
> 0: MWDMA2 RAID1RAID 0+1 Volume: 0 SAMSUNG HD400LD
> 1: MWDMA2 RAID1RAID 0+1 Volume: 0 SAMSUNG HD400LD
> scsi2 : pata_it821x
> scsi3 : pata_it821x
> ata3: PATA max UDMA/133 cmd 0x6800 ctl 0x6c00 bmdma 0x7800 irq 11
> ata4: PATA max UDMA/133 cmd 0x7000 ctl 0x7400 bmdma 0x7808 irq 11
> ata3.00: ATA-4: Integrated Technology Express Inc, , max MWDMA2
> ata3.00: 781422766 sectors, multi 0: LBA48
> ata3.00: RAID1 volume.
> ata3.00: configured for DMA
> scsi 2:0:0:0: Direct-Access ATA Integrated Techn n/a PQ: 0 ANSI: 5
> sd 2:0:0:0: [sdb] 781422766 512-byte hardware sectors (400088 MB)
> sd 2:0:0:0: [sdb] Write Protect is off
> sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
> sd 2:0:0:0: [sdb] 781422766 512-byte hardware sectors (400088 MB)
> sd 2:0:0:0: [sdb] Write Protect is off
> sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
> sdb: sdb1 sdb2 sdb3 sdb4
> sd 2:0:0:0: [sdb] Attached SCSI disk
> sd 2:0:0:0: Attached scsi generic sg2 type 0
>
>
> /dev/sdb:
> Timing buffered disk reads: 60 MB in 3.01 seconds = 19.91 MB/sec
>
>
>
> Fix LBA48 on pata_it821x RAID volumes.
>
> Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2008-10-18 18:16 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-10-18 11:42 pata_it821x in 2.6.27 - works but no LBA48 and "hdparm -t" is slower Ondrej Zary
2008-10-18 16:30 ` [PATCH] " Ondrej Zary
2008-10-18 17:46 ` Alan Cox
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox