* 2.6.27 - swncq problem with nforce 570 and ST3320620AS?
@ 2008-12-02 10:13 Jan De Luyck
2008-12-04 5:45 ` Robert Hancock
2008-12-07 21:20 ` Rafael J. Wysocki
0 siblings, 2 replies; 4+ messages in thread
From: Jan De Luyck @ 2008-12-02 10:13 UTC (permalink / raw)
To: linux-kernel
Hello,
I switched not too long ago to 2.6.27-series, and since then I've been getting this now and then at bootup:
This was with 2.6.27.4, upgraded today to 2.6.27.7.
Disk in question is:
ATA device, with non-removable media
Model Number: ST3320620AS
Serial Number: 9QF1QMGA
Firmware Revision: 3.AAE
whocares kernel: ata4: EH in SWNCQ mode,QC:qc_active 0x6 sactive 0x6
whocares kernel: ata4: SWNCQ:qc_active 0x6 defer_bits 0x0 last_issue_tag 0x2
whocares kernel: dhfis 0x6 dmafis 0x2 sdbfis 0x0
whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
whocares kernel: ata4: tag 0x1: 1 1 0 1
whocares kernel: ata4: tag 0x2: 1 0 0 1
whocares kernel: ata4.00: exception Emask 0x0 SAct 0x6 SErr 0x1800000 action 0x6 frozen
whocares kernel: ata4: SError: { LinkSeq TrStaTrns }
whocares kernel: ata4.00: cmd 60/3e:08:61:00:00/00:00:00:00:00/40 tag 1 ncq 31744 in
whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
whocares kernel: ata4.00: status: { DRDY }
whocares kernel: ata4.00: cmd 60/02:10:bf:d6:42/00:00:25:00:00/40 tag 2 ncq 1024 in
whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
whocares kernel: ata4.00: status: { DRDY }
whocares kernel: ata4: hard resetting link
whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
whocares kernel: ata4.00: configured for UDMA/133
whocares kernel: ata4: EH complete
whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
...
whocares kernel: XFS mounting filesystem sdd1
whocares kernel: ata4: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF
whocares kernel: ata4: SWNCQ:qc_active 0x1 defer_bits 0xE last_issue_tag 0x0
whocares kernel: dhfis 0x1 dmafis 0x1 sdbfis 0x0
whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
whocares kernel: ata4: tag 0x0: 1 1 0 1
whocares kernel: ata4.00: exception Emask 0x0 SAct 0xf SErr 0x400000 action 0x6 frozen
whocares kernel: ata4: SError: { Handshk }
whocares kernel: ata4.00: cmd 61/00:00:9f:8d:a2/04:00:12:00:00/40 tag 0 ncq 524288 out
whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
whocares kernel: ata4.00: status: { DRDY }
whocares kernel: ata4.00: cmd 61/00:08:9f:91:a2/04:00:12:00:00/40 tag 1 ncq 524288 out
whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
whocares kernel: ata4.00: status: { DRDY }
whocares kernel: ata4.00: cmd 61/00:10:9f:95:a2/04:00:12:00:00/40 tag 2 ncq 524288 out
whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
whocares kernel: ata4.00: status: { DRDY }
whocares kernel: ata4.00: cmd 61/00:18:9f:99:a2/04:00:12:00:00/40 tag 3 ncq 524288 out
whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
whocares kernel: ata4.00: status: { DRDY }
whocares kernel: ata4: hard resetting link
whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
whocares kernel: ata4.00: configured for UDMA/133
whocares kernel: ata4: EH complete
whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
whocares kernel: ata4: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF
whocares kernel: ata4: SWNCQ:qc_active 0x1 defer_bits 0xE last_issue_tag 0x0
whocares kernel: dhfis 0x1 dmafis 0x1 sdbfis 0x0
whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
whocares kernel: ata4: tag 0x0: 1 1 0 1
whocares kernel: ata4.00: exception Emask 0x0 SAct 0xf SErr 0x400000 action 0x6 frozen
whocares kernel: ata4: SError: { Handshk }
whocares kernel: ata4.00: cmd 61/00:00:9f:99:a2/04:00:12:00:00/40 tag 0 ncq 524288 out
whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
whocares kernel: ata4.00: status: { DRDY }
whocares kernel: ata4.00: cmd 61/00:08:9f:95:a2/04:00:12:00:00/40 tag 1 ncq 524288 out
whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
whocares kernel: ata4.00: status: { DRDY }
whocares kernel: ata4.00: cmd 61/00:10:9f:91:a2/04:00:12:00:00/40 tag 2 ncq 524288 out
whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
whocares kernel: ata4.00: status: { DRDY }
whocares kernel: ata4.00: cmd 61/00:18:9f:8d:a2/04:00:12:00:00/40 tag 3 ncq 524288 out
whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
whocares kernel: ata4.00: status: { DRDY }
whocares kernel: ata4: hard resetting link
whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
whocares kernel: ata4.00: configured for UDMA/133
whocares kernel: ata4: EH complete
whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
whocares kernel: Ending clean XFS mount for filesystem: sdd1
...
Anyone any idea what might be causing this?
I have several disks of the same type in my PC, with different firmwares though - this is the only
one exhibiting this problem.
Kind regards
Jan
--
Tu bi or not tu bi
FAIL -- Antônimo de bonito: Ele é FAIL
RIVER -- Pior que FAIL: Ele é o RIVER
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 2.6.27 - swncq problem with nforce 570 and ST3320620AS?
2008-12-02 10:13 2.6.27 - swncq problem with nforce 570 and ST3320620AS? Jan De Luyck
@ 2008-12-04 5:45 ` Robert Hancock
2008-12-04 6:22 ` Justin P. Mattock
2008-12-07 21:20 ` Rafael J. Wysocki
1 sibling, 1 reply; 4+ messages in thread
From: Robert Hancock @ 2008-12-04 5:45 UTC (permalink / raw)
To: linux-kernel
Jan De Luyck wrote:
> Hello,
>
> I switched not too long ago to 2.6.27-series, and since then I've been getting this now and then at bootup:
>
> This was with 2.6.27.4, upgraded today to 2.6.27.7.
>
> Disk in question is:
>
> ATA device, with non-removable media
> Model Number: ST3320620AS
> Serial Number: 9QF1QMGA
> Firmware Revision: 3.AAE
>
> whocares kernel: ata4: EH in SWNCQ mode,QC:qc_active 0x6 sactive 0x6
> whocares kernel: ata4: SWNCQ:qc_active 0x6 defer_bits 0x0 last_issue_tag 0x2
> whocares kernel: dhfis 0x6 dmafis 0x2 sdbfis 0x0
> whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
> whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
> whocares kernel: ata4: tag 0x1: 1 1 0 1
> whocares kernel: ata4: tag 0x2: 1 0 0 1
> whocares kernel: ata4.00: exception Emask 0x0 SAct 0x6 SErr 0x1800000 action 0x6 frozen
> whocares kernel: ata4: SError: { LinkSeq TrStaTrns }
> whocares kernel: ata4.00: cmd 60/3e:08:61:00:00/00:00:00:00:00/40 tag 1 ncq 31744 in
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 60/02:10:bf:d6:42/00:00:25:00:00/40 tag 2 ncq 1024 in
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4: hard resetting link
> whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> whocares kernel: ata4.00: configured for UDMA/133
> whocares kernel: ata4: EH complete
> whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
> whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
> whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
> whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> ...
> whocares kernel: XFS mounting filesystem sdd1
> whocares kernel: ata4: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF
> whocares kernel: ata4: SWNCQ:qc_active 0x1 defer_bits 0xE last_issue_tag 0x0
> whocares kernel: dhfis 0x1 dmafis 0x1 sdbfis 0x0
> whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
> whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
> whocares kernel: ata4: tag 0x0: 1 1 0 1
> whocares kernel: ata4.00: exception Emask 0x0 SAct 0xf SErr 0x400000 action 0x6 frozen
> whocares kernel: ata4: SError: { Handshk }
> whocares kernel: ata4.00: cmd 61/00:00:9f:8d:a2/04:00:12:00:00/40 tag 0 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:08:9f:91:a2/04:00:12:00:00/40 tag 1 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:10:9f:95:a2/04:00:12:00:00/40 tag 2 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:18:9f:99:a2/04:00:12:00:00/40 tag 3 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4: hard resetting link
> whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> whocares kernel: ata4.00: configured for UDMA/133
> whocares kernel: ata4: EH complete
> whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
> whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
> whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
> whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> whocares kernel: ata4: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF
> whocares kernel: ata4: SWNCQ:qc_active 0x1 defer_bits 0xE last_issue_tag 0x0
> whocares kernel: dhfis 0x1 dmafis 0x1 sdbfis 0x0
> whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
> whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
> whocares kernel: ata4: tag 0x0: 1 1 0 1
> whocares kernel: ata4.00: exception Emask 0x0 SAct 0xf SErr 0x400000 action 0x6 frozen
> whocares kernel: ata4: SError: { Handshk }
> whocares kernel: ata4.00: cmd 61/00:00:9f:99:a2/04:00:12:00:00/40 tag 0 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:08:9f:95:a2/04:00:12:00:00/40 tag 1 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:10:9f:91:a2/04:00:12:00:00/40 tag 2 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:18:9f:8d:a2/04:00:12:00:00/40 tag 3 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4: hard resetting link
> whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> whocares kernel: ata4.00: configured for UDMA/133
> whocares kernel: ata4: EH complete
> whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
> whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
> whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
> whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> whocares kernel: Ending clean XFS mount for filesystem: sdd1
> ...
>
> Anyone any idea what might be causing this?
>
> I have several disks of the same type in my PC, with different firmwares though - this is the only
> one exhibiting this problem.
This fact and the fact that those SError bits are showing up does
potentially point to a hardware issue.. perhaps a problem with the
cable, or this drive is somehow getting worse power than the others?
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 2.6.27 - swncq problem with nforce 570 and ST3320620AS?
2008-12-04 5:45 ` Robert Hancock
@ 2008-12-04 6:22 ` Justin P. Mattock
0 siblings, 0 replies; 4+ messages in thread
From: Justin P. Mattock @ 2008-12-04 6:22 UTC (permalink / raw)
To: Robert Hancock; +Cc: Linux Kernel Mailing List
I was receiving the { DRDY }
thing with some .config option
from Some distro I was using,
Then revered to my f*^%ed
Up .config and all was good.
Try experimenting if this helps.
justin P. Mattock
On Dec 3, 2008, at 9:45 PM, Robert Hancock <hancockr@shaw.ca> wrote:
> Jan De Luyck wrote:
>> Hello,
>> I switched not too long ago to 2.6.27-series, and since then I've
>> been getting this now and then at bootup:
>> This was with 2.6.27.4, upgraded today to 2.6.27.7.
>> Disk in question is:
>> ATA device, with non-removable media
>> Model Number:
>> ST3320620AS Serial Number:
>> 9QF1QMGA
>> Firmware Revision: 3.AAE whocares kernel: ata4: EH in
>> SWNCQ mode,QC:qc_active 0x6 sactive 0x6
>> whocares kernel: ata4: SWNCQ:qc_active 0x6 defer_bits 0x0
>> last_issue_tag 0x2
>> whocares kernel: dhfis 0x6 dmafis 0x2 sdbfis 0x0
>> whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
>> whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
>> whocares kernel: ata4: tag 0x1: 1 1 0 1
>> whocares kernel: ata4: tag 0x2: 1 0 0 1
>> whocares kernel: ata4.00: exception Emask 0x0 SAct 0x6 SErr
>> 0x1800000 action 0x6 frozen
>> whocares kernel: ata4: SError: { LinkSeq TrStaTrns }
>> whocares kernel: ata4.00: cmd 60/3e:08:61:00:00/00:00:00:00:00/40
>> tag 1 ncq 31744 in
>> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00
>> Emask 0x4 (timeout)
>> whocares kernel: ata4.00: status: { DRDY }
>> whocares kernel: ata4.00: cmd 60/02:10:bf:d6:42/00:00:25:00:00/40
>> tag 2 ncq 1024 in
>> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00
>> Emask 0x4 (timeout)
>> whocares kernel: ata4.00: status: { DRDY }
>> whocares kernel: ata4: hard resetting link
>> whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl
>> 300)
>> whocares kernel: ata4.00: configured for UDMA/133
>> whocares kernel: ata4: EH complete
>> whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware
>> sectors (320073 MB)
>> whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
>> whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
>> whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read
>> cache: enabled, doesn't support DPO or FUA
>> ...
>> whocares kernel: XFS mounting filesystem sdd1
>> whocares kernel: ata4: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF
>> whocares kernel: ata4: SWNCQ:qc_active 0x1 defer_bits 0xE
>> last_issue_tag 0x0
>> whocares kernel: dhfis 0x1 dmafis 0x1 sdbfis 0x0
>> whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
>> whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
>> whocares kernel: ata4: tag 0x0: 1 1 0 1
>> whocares kernel: ata4.00: exception Emask 0x0 SAct 0xf SErr
>> 0x400000 action 0x6 frozen
>> whocares kernel: ata4: SError: { Handshk }
>> whocares kernel: ata4.00: cmd 61/00:00:9f:8d:a2/04:00:12:00:00/40
>> tag 0 ncq 524288 out
>> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/40
>> Emask 0x4 (timeout)
>> whocares kernel: ata4.00: status: { DRDY }
>> whocares kernel: ata4.00: cmd 61/00:08:9f:91:a2/04:00:12:00:00/40
>> tag 1 ncq 524288 out
>> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00
>> Emask 0x4 (timeout)
>> whocares kernel: ata4.00: status: { DRDY }
>> whocares kernel: ata4.00: cmd 61/00:10:9f:95:a2/04:00:12:00:00/40
>> tag 2 ncq 524288 out
>> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00
>> Emask 0x4 (timeout)
>> whocares kernel: ata4.00: status: { DRDY }
>> whocares kernel: ata4.00: cmd 61/00:18:9f:99:a2/04:00:12:00:00/40
>> tag 3 ncq 524288 out
>> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00
>> Emask 0x4 (timeout)
>> whocares kernel: ata4.00: status: { DRDY }
>> whocares kernel: ata4: hard resetting link
>> whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl
>> 300)
>> whocares kernel: ata4.00: configured for UDMA/133
>> whocares kernel: ata4: EH complete
>> whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware
>> sectors (320073 MB)
>> whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
>> whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
>> whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read
>> cache: enabled, doesn't support DPO or FUA
>> whocares kernel: ata4: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF
>> whocares kernel: ata4: SWNCQ:qc_active 0x1 defer_bits 0xE
>> last_issue_tag 0x0
>> whocares kernel: dhfis 0x1 dmafis 0x1 sdbfis 0x0
>> whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
>> whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
>> whocares kernel: ata4: tag 0x0: 1 1 0 1
>> whocares kernel: ata4.00: exception Emask 0x0 SAct 0xf SErr
>> 0x400000 action 0x6 frozen
>> whocares kernel: ata4: SError: { Handshk }
>> whocares kernel: ata4.00: cmd 61/00:00:9f:99:a2/04:00:12:00:00/40
>> tag 0 ncq 524288 out
>> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/40
>> Emask 0x4 (timeout)
>> whocares kernel: ata4.00: status: { DRDY }
>> whocares kernel: ata4.00: cmd 61/00:08:9f:95:a2/04:00:12:00:00/40
>> tag 1 ncq 524288 out
>> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00
>> Emask 0x4 (timeout)
>> whocares kernel: ata4.00: status: { DRDY }
>> whocares kernel: ata4.00: cmd 61/00:10:9f:91:a2/04:00:12:00:00/40
>> tag 2 ncq 524288 out
>> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00
>> Emask 0x4 (timeout)
>> whocares kernel: ata4.00: status: { DRDY }
>> whocares kernel: ata4.00: cmd 61/00:18:9f:8d:a2/04:00:12:00:00/40
>> tag 3 ncq 524288 out
>> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00
>> Emask 0x4 (timeout)
>> whocares kernel: ata4.00: status: { DRDY }
>> whocares kernel: ata4: hard resetting link
>> whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl
>> 300)
>> whocares kernel: ata4.00: configured for UDMA/133
>> whocares kernel: ata4: EH complete
>> whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware
>> sectors (320073 MB)
>> whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
>> whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
>> whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read
>> cache: enabled, doesn't support DPO or FUA
>> whocares kernel: Ending clean XFS mount for filesystem: sdd1
>> ...
>> Anyone any idea what might be causing this?
>> I have several disks of the same type in my PC, with different
>> firmwares though - this is the only one exhibiting this problem.
>
> This fact and the fact that those SError bits are showing up does
> potentially point to a hardware issue.. perhaps a problem with the
> cable, or this drive is somehow getting worse power than the others?
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-
> kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 2.6.27 - swncq problem with nforce 570 and ST3320620AS?
2008-12-02 10:13 2.6.27 - swncq problem with nforce 570 and ST3320620AS? Jan De Luyck
2008-12-04 5:45 ` Robert Hancock
@ 2008-12-07 21:20 ` Rafael J. Wysocki
1 sibling, 0 replies; 4+ messages in thread
From: Rafael J. Wysocki @ 2008-12-07 21:20 UTC (permalink / raw)
To: Jan De Luyck; +Cc: linux-kernel
On Tuesday, 2 of December 2008, Jan De Luyck wrote:
> Hello,
>
> I switched not too long ago to 2.6.27-series, and since then I've been getting this now and then at bootup:
>
> This was with 2.6.27.4, upgraded today to 2.6.27.7.
Does it happen with the current mainline too?
Rafael
> Disk in question is:
>
> ATA device, with non-removable media
> Model Number: ST3320620AS
> Serial Number: 9QF1QMGA
> Firmware Revision: 3.AAE
>
> whocares kernel: ata4: EH in SWNCQ mode,QC:qc_active 0x6 sactive 0x6
> whocares kernel: ata4: SWNCQ:qc_active 0x6 defer_bits 0x0 last_issue_tag 0x2
> whocares kernel: dhfis 0x6 dmafis 0x2 sdbfis 0x0
> whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
> whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
> whocares kernel: ata4: tag 0x1: 1 1 0 1
> whocares kernel: ata4: tag 0x2: 1 0 0 1
> whocares kernel: ata4.00: exception Emask 0x0 SAct 0x6 SErr 0x1800000 action 0x6 frozen
> whocares kernel: ata4: SError: { LinkSeq TrStaTrns }
> whocares kernel: ata4.00: cmd 60/3e:08:61:00:00/00:00:00:00:00/40 tag 1 ncq 31744 in
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 60/02:10:bf:d6:42/00:00:25:00:00/40 tag 2 ncq 1024 in
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4: hard resetting link
> whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> whocares kernel: ata4.00: configured for UDMA/133
> whocares kernel: ata4: EH complete
> whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
> whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
> whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
> whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> ...
> whocares kernel: XFS mounting filesystem sdd1
> whocares kernel: ata4: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF
> whocares kernel: ata4: SWNCQ:qc_active 0x1 defer_bits 0xE last_issue_tag 0x0
> whocares kernel: dhfis 0x1 dmafis 0x1 sdbfis 0x0
> whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
> whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
> whocares kernel: ata4: tag 0x0: 1 1 0 1
> whocares kernel: ata4.00: exception Emask 0x0 SAct 0xf SErr 0x400000 action 0x6 frozen
> whocares kernel: ata4: SError: { Handshk }
> whocares kernel: ata4.00: cmd 61/00:00:9f:8d:a2/04:00:12:00:00/40 tag 0 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:08:9f:91:a2/04:00:12:00:00/40 tag 1 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:10:9f:95:a2/04:00:12:00:00/40 tag 2 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:18:9f:99:a2/04:00:12:00:00/40 tag 3 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4: hard resetting link
> whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> whocares kernel: ata4.00: configured for UDMA/133
> whocares kernel: ata4: EH complete
> whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
> whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
> whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
> whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> whocares kernel: ata4: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF
> whocares kernel: ata4: SWNCQ:qc_active 0x1 defer_bits 0xE last_issue_tag 0x0
> whocares kernel: dhfis 0x1 dmafis 0x1 sdbfis 0x0
> whocares kernel: ata4: ATA_REG 0x40 ERR_REG 0x0
> whocares kernel: ata4: tag : dhfis dmafis sdbfis sacitve
> whocares kernel: ata4: tag 0x0: 1 1 0 1
> whocares kernel: ata4.00: exception Emask 0x0 SAct 0xf SErr 0x400000 action 0x6 frozen
> whocares kernel: ata4: SError: { Handshk }
> whocares kernel: ata4.00: cmd 61/00:00:9f:99:a2/04:00:12:00:00/40 tag 0 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:08:9f:95:a2/04:00:12:00:00/40 tag 1 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:10:9f:91:a2/04:00:12:00:00/40 tag 2 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4.00: cmd 61/00:18:9f:8d:a2/04:00:12:00:00/40 tag 3 ncq 524288 out
> whocares kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> whocares kernel: ata4.00: status: { DRDY }
> whocares kernel: ata4: hard resetting link
> whocares kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> whocares kernel: ata4.00: configured for UDMA/133
> whocares kernel: ata4: EH complete
> whocares kernel: sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
> whocares kernel: sd 3:0:0:0: [sdd] Write Protect is off
> whocares kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
> whocares kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> whocares kernel: Ending clean XFS mount for filesystem: sdd1
> ...
>
> Anyone any idea what might be causing this?
>
> I have several disks of the same type in my PC, with different firmwares though - this is the only
> one exhibiting this problem.
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2008-12-07 21:20 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-12-02 10:13 2.6.27 - swncq problem with nforce 570 and ST3320620AS? Jan De Luyck
2008-12-04 5:45 ` Robert Hancock
2008-12-04 6:22 ` Justin P. Mattock
2008-12-07 21:20 ` Rafael J. Wysocki
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox