public inbox for linux-kernel@vger.kernel.org
 help / color / mirror / Atom feed
From: Michael Bramer <michael@debsupport.de>
To: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: linux-kernel@vger.kernel.org, linux-serial@vger.kernel.org
Subject: Re: [PATCH] drivers/serial/8250_pci.c (add support for '8-port RS-232 MIC-3620 from advantech'
Date: Mon, 19 Jan 2009 11:45:26 +0000	[thread overview]
Message-ID: <20090119114526.GA1714@deb-support.de> (raw)
In-Reply-To: <20090118141409.3c2d0f95@lxorguk.ukuu.org.uk>

On Sun, Jan 18, 2009 at 02:14:09PM +0000, Alan Cox wrote:
> > +               .vendor         = PCI_VENDOR_ID_ADVANTECH,
> > +               .device         = PCI_DEVICE_ID_ADVANTECH_PCI3620,
> > +               .subvendor      = PCI_DEVICE_ID_ADVANTECH_PCI3620,
> > +               .subdevice      = PCI_ANY_ID,
> 
> This looks odd - the subvendor ought to be a vendor id, and there should
> be a device id as well.

the number ist the same... i use now numbers in the patch...

> > can you add this in the next linux kernel?
> 
> Can you firstly send me an lspci -vvxxx of that device. Also see
> Documentation/SubmittingPatches about Signed-off-by lines and we'll sort
> out merging it.

done:

eps:~# lspci -vvxxx -d 13fe:3620
04:0d.0 Serial controller: Advantech Co. Ltd Device 3620 (rev 01) (prog-if 00 [8250])
        Subsystem: Device 3620:0001
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at fddff000 (32-bit, non-prefetchable) [size=128]
        Region 2: I/O ports at df00 [size=128]
        Capabilities: [40] Power Management version 1
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [48] CompactPCI hot-swap <?>
        Capabilities: [4c] Vital Product Data <?>
        Kernel modules: 8250_pci-, 8250_pci
00: fe 13 20 36 03 00 90 02 01 00 00 07 10 00 00 00
10: 00 f0 df fd 00 00 00 00 01 df 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 20 36 01 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
40: 01 48 01 48 00 00 00 00 06 4c 00 00 03 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

and now the patch:
--------------
This Patch add the device information for the 
MIC-3620 8-port RS-232 cPCI card from Advantech Co. Ltd.

Signed-off-by: Michael Bramer <grisu@deb-support.de>
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -31,6 +31,7 @@
 #include "8250.h"

 #undef SERIAL_DEBUG_PCI
+#define SERIAL_DEBUG_PCI

 /*
  * init function returns:
@@ -768,6 +769,8 @@
 #define PCI_SUBDEVICE_ID_OCTPRO422     0x0208
 #define PCI_SUBDEVICE_ID_POCTAL232     0x0308
 #define PCI_SUBDEVICE_ID_POCTAL422     0x0408
+#define PCI_VENDOR_ID_ADVANTECH         0x13fe
+#define PCI_DEVICE_ID_ADVANTECH_PCI3620 0x3620

 /*
  * Master list of serial port init/setup/exit quirks.
@@ -789,6 +792,16 @@
                .setup          = addidata_apci7800_setup,
        },
        /*
+        * ADVANTECH
+        */
+       {
+               .vendor         = PCI_VENDOR_ID_ADVANTECH,
+               .device         = PCI_DEVICE_ID_ADVANTECH_PCI3620,
+               .subvendor      = 0x3620,
+               .subdevice      = PCI_ANY_ID,
+               .setup          = pci_default_setup,
+       },
+       /*
         * AFAVLAB cards - these may be called via parport_serial
         *  It is not clear whether this applies to all products.
         */
@@ -2041,6 +2054,9 @@
 #endif

 static struct pci_device_id serial_pci_tbl[] = {
+       {       PCI_VENDOR_ID_ADVANTECH, PCI_DEVICE_ID_ADVANTECH_PCI3620,
+               PCI_DEVICE_ID_ADVANTECH_PCI3620, PCI_ANY_ID, 0, 0,
+               pbn_b2_8_921600 },
        {       PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
                PCI_SUBVENDOR_ID_CONNECT_TECH,
                PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0,
--------------

Thanks for your help

Gruss
Grisu
-- 
Michael Bramer  -- http://www.feuerwehr.kreuzau.de/wiki/
PGP: finger grisu@db.debian.org  -- Linux Sysadmin   -- Use Debian Linux
"Wenn ich die Folgen geahnt hätte, wäre ich Uhrmacher geworden!"
                                                 --- Albert Einstein

  reply	other threads:[~2009-01-19 11:45 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2009-01-18 13:53 [PATCH] drivers/serial/8250_pci.c (add support for '8-port RS-232 MIC-3620 from advantech' Michael Bramer
2009-01-18 14:14 ` Alan Cox
2009-01-19 11:45   ` Michael Bramer [this message]
2009-01-19 14:51 ` Andrey Panin
2009-01-19 23:51   ` Michael Bramer
2009-01-20 15:12     ` Andrey Panin
2009-01-21  7:52       ` Michael Bramer
2009-01-21  8:18         ` Paulius Zaleckas
2009-01-21  8:40           ` Niels de Vos
2009-01-21 12:32             ` Alan Cox
2009-01-21 23:42               ` Michael Bramer
2009-01-22  8:21                 ` Tosoni
2009-01-22  9:03                   ` Niels de Vos
2009-01-22 11:00                     ` Michael Bramer
2009-01-22 11:47                       ` Paulius Zaleckas
2009-01-22 16:44                         ` Michael Bramer
2009-01-21 23:40           ` Michael Bramer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20090119114526.GA1714@deb-support.de \
    --to=michael@debsupport.de \
    --cc=alan@lxorguk.ukuu.org.uk \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-serial@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox