Comparison between .28 and .29-rc3 for STR cycle

Frans Pop
2009-02-03T11:38:13Z

Hi Rafael,

I've compared the log messages during a suspend/resume (STR) cycle for my
HP 2510p notebook. In general the changes look OK, but I noticed a few
things that I think may be worth looking into.

The analysis is based on v2.6.29-rc3-100-gf2257b7 with the following relevant
extra patches:
- PCI PM: Fix suspend error paths and testing facility breakage
- ricoh_mmc: Use suspend_late/resume_early

Below a *pseudo* diff between messages from .28-rc7 and .29-rc3-100. I've
concentrated on showing _what_ messages are shown, not _when_ they are shown.
Messages are shown in the order they appear with .29.

I've added some comments in the "diff" to indicate points of interest.

Summary of changes:
- Most config restores now happen during resume-early, but there are still
some displayed later, including some duplicates.
- There are a lot more "PME# disabled" messages, both during suspend (which
seems redundant?) and during resume. There are a few duplicates and it
happen for a few devices for which it is not done during normal boot.

Cheers,
FJP

Pseudo diff
-----------
Freezing user space processes ... (elapsed 0.00 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
# I would not have expected this next line to disappear. Device is VGA controller.
-pci 0000:00:02.0: PCI INT A disabled
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
ACPI handle has no context!
ACPI handle has no context!
+sdhci-pci 0000:02:06.2: PME# disabled
sdhci-pci 0000:02:06.2: PCI INT C disabled
ACPI handle has no context!
ACPI handle has no context!
iwlagn 0000:10:00.0: PCI INT A disabled
ata2: port disabled. ignoring.
ata_piix 0000:00:1f.1: PCI INT A disabled
ehci_hcd 0000:00:1d.7: PCI INT A disabled
+ehci_hcd 0000:00:1d.7: PME# disabled
uhci_hcd 0000:00:1d.2: PCI INT C disabled
uhci_hcd 0000:00:1d.1: PCI INT B disabled
uhci_hcd 0000:00:1d.0: PCI INT A disabled
HDA Intel 0000:00:1b.0: PCI INT A disabled
HDA Intel 0000:00:1b.0: power state changed by ACPI to D3
ehci_hcd 0000:00:1a.7: PCI INT C disabled
+ehci_hcd 0000:00:1a.7: PME# disabled
uhci_hcd 0000:00:1a.1: PCI INT B disabled
uhci_hcd 0000:00:1a.0: PCI INT A disabled
e1000e 0000:00:19.0: PME# enabled
# Not a change, but still strange that next 2 lines are duplicated.
e1000e 0000:00:19.0: wake-up capability enabled by ACPI
e1000e 0000:00:19.0: PME# enabled
e1000e 0000:00:19.0: wake-up capability enabled by ACPI
e1000e 0000:00:19.0: PCI INT A disabled
ACPI handle has no context!
ACPI: Preparing to enter system sleep state S3
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU0 attaching NULL sched-domain.
CPU1 attaching NULL sched-domain.
CPU0 attaching NULL sched-domain.
CPU1 is down
ricoh-mmc: Suspending.
ricoh-mmc: Controller is now re-enabled.
Extended CMOS year: 2000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Back to C!
Extended CMOS year: 2000
pci 0000:00:02.0: restoring config space at offset 0x8 (was 0x1, writing 0x2001)
pci 0000:00:02.1: restoring config space at offset 0x4 (was 0x4, writing 0xe0500004)
pci 0000:00:02.1: restoring config space at offset 0x1 (was 0x900000, writing 0x900007)
pci 0000:00:03.0: restoring config space at offset 0xf (was 0x100, writing 0x1ff)
pci 0000:00:03.0: restoring config space at offset 0x4 (was 0xfed12004, writing 0xe0600004)
pci 0000:00:03.2: restoring config space at offset 0xf (was 0x300, writing 0x30b)
pci 0000:00:03.2: restoring config space at offset 0x8 (was 0x1, writing 0x2031)
pci 0000:00:03.2: restoring config space at offset 0x7 (was 0x1, writing 0x2021)
pci 0000:00:03.2: restoring config space at offset 0x6 (was 0x1, writing 0x2019)
pci 0000:00:03.2: restoring config space at offset 0x5 (was 0x1, writing 0x2011)
pci 0000:00:03.2: restoring config space at offset 0x4 (was 0x1, writing 0x2009)
pci 0000:00:03.2: restoring config space at offset 0x1 (was 0xb00000, writing 0xb00001)
serial 0000:00:03.3: restoring config space at offset 0xf (was 0x200, writing 0x20a)
serial 0000:00:03.3: restoring config space at offset 0x5 (was 0x0, writing 0xe0601000)
serial 0000:00:03.3: restoring config space at offset 0x4 (was 0x1, writing 0x2041)
serial 0000:00:03.3: restoring config space at offset 0x1 (was 0xb00000, writing 0xb00007)
e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
e1000e 0000:00:19.0: restoring config space at offset 0x6 (was 0x1, writing 0x2061)
e1000e 0000:00:19.0: restoring config space at offset 0x5 (was 0x0, writing 0xe0640000)
e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100007)
uhci_hcd 0000:00:1a.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
uhci_hcd 0000:00:1a.0: restoring config space at offset 0x8 (was 0x1, writing 0x2081)
+uhci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was 0x2800000, writing 0x2800001)
uhci_hcd 0000:00:1a.1: restoring config space at offset 0xf (was 0x200, writing 0x20a)
uhci_hcd 0000:00:1a.1: restoring config space at offset 0x8 (was 0x1, writing 0x20a1)
+uhci_hcd 0000:00:1a.1: restoring config space at offset 0x1 (was 0x2800000, writing 0x2800001)
ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30b)
ehci_hcd 0000:00:1a.7: restoring config space at offset 0x4 (was 0x0, writing 0xe0641000)
+ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002)
HDA Intel 0000:00:1b.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
HDA Intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
HDA Intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100002)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0xf (was 0x100, writing 0x4010a)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x9 (was 0x10001, writing 0x1fff1)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x8 (was 0x0, writing 0xfff0)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x7 (was 0x0, writing 0x200000f0)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x6 (was 0x0, writing 0x80800)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x3 (was 0x810000, writing 0x810010)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
# Weird, we already did a config restore at offset 0x7 4 lines up!
# So where does this next line come from?
+pcieport-driver 0000:00:1c.0: restoring config space at offset 0x7 (was 0xf0, writing 0x200000f0)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0xf (was 0x200, writing 0x4020a)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x9 (was 0x10001, writing 0x1fff1)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x8 (was 0x0, writing 0xe000e000)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x7 (was 0x0, writing 0xf0)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x3 (was 0x810000, writing 0x810010)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
uhci_hcd 0000:00:1d.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
uhci_hcd 0000:00:1d.0: restoring config space at offset 0x8 (was 0x1, writing 0x20c1)
+uhci_hcd 0000:00:1d.0: restoring config space at offset 0x1 (was 0x2800000, writing 0x2800001)
uhci_hcd 0000:00:1d.1: restoring config space at offset 0xf (was 0x200, writing 0x20b)
uhci_hcd 0000:00:1d.1: restoring config space at offset 0x8 (was 0x1, writing 0x20e1)
+uhci_hcd 0000:00:1d.1: restoring config space at offset 0x1 (was 0x2800000, writing 0x2800001)
uhci_hcd 0000:00:1d.2: restoring config space at offset 0xf (was 0x300, writing 0x30b)
uhci_hcd 0000:00:1d.2: restoring config space at offset 0x8 (was 0x1, writing 0x2101)
+uhci_hcd 0000:00:1d.2: restoring config space at offset 0x1 (was 0x2800000, writing 0x2800001)
ehci_hcd 0000:00:1d.7: restoring config space at offset 0xf (was 0x100, writing 0x10a)
ehci_hcd 0000:00:1d.7: restoring config space at offset 0x4 (was 0x0, writing 0xe0648000)
+ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002)
pci 0000:00:1e.0: restoring config space at offset 0x9 (was 0x10001, writing 0x83f18001)
pci 0000:00:1e.0: restoring config space at offset 0x8 (was 0x0, writing 0xe030e010)
pci 0000:00:1e.0: restoring config space at offset 0x7 (was 0x228000f0, writing 0x22803030)
pci 0000:00:1e.0: restoring config space at offset 0x1 (was 0x100007, writing 0x100103)
ata_piix 0000:00:1f.1: restoring config space at offset 0xf (was 0x100, writing 0x10a)
ata_piix 0000:00:1f.1: restoring config space at offset 0x8 (was 0xc01, writing 0x2121)
ata_piix 0000:00:1f.1: restoring config space at offset 0x1 (was 0x2800005, writing 0x2880005)
iwlagn 0000:10:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
iwlagn 0000:10:00.0: restoring config space at offset 0x4 (was 0x4, writing 0xe0000004)
iwlagn 0000:10:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
iwlagn 0000:10:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100006)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0xf (was 0x3000100, writing 0x580010b)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0xe (was 0x0, writing 0x34fc)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0xd (was 0x0, writing 0x3400)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0xc (was 0x0, writing 0x30fc)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0xb (was 0x0, writing 0x3000)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0xa (was 0x0, writing 0x87fff000)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0x9 (was 0x0, writing 0x84000000)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0x8 (was 0x0, writing 0x83fff000)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0x7 (was 0x0, writing 0x80000000)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0x6 (was 0x0, writing 0xb0060302)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0x4 (was 0x0, writing 0xe0100000)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0x3 (was 0x820000, writing 0x82a800)
yenta_cardbus 0000:02:06.0: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100007)
ohci1394 0000:02:06.1: restoring config space at offset 0xf (was 0x4020200, writing 0x4020205)
ohci1394 0000:02:06.1: restoring config space at offset 0x4 (was 0x0, writing 0xe0101000)
ohci1394 0000:02:06.1: restoring config space at offset 0x3 (was 0x800000, writing 0x804010)
ohci1394 0000:02:06.1: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100006)
sdhci-pci 0000:02:06.2: restoring config space at offset 0xf (was 0x300, writing 0x30a)
sdhci-pci 0000:02:06.2: restoring config space at offset 0x4 (was 0x0, writing 0xe0102000)
sdhci-pci 0000:02:06.2: restoring config space at offset 0x3 (was 0x800000, writing 0x804010)
sdhci-pci 0000:02:06.2: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100006)
# Apparently we did not do a config restore for ricoh-mmc before. Surprising there are so many.
# And are the values that are written correct (all 0xffffffff...)?
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0xf (was 0x300, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0xe (was 0x0, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0xd (was 0x80, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0xc (was 0x0, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0xb (was 0x30c9103c, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0xa (was 0x0, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0x9 (was 0x0, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0x8 (was 0x0, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0x7 (was 0x0, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0x6 (was 0x0, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0x5 (was 0x0, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0x4 (was 0x0, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0x3 (was 0x800000, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0x2 (was 0x8800011, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0x1 (was 0x2100000, writing 0xffffffff)
+ricoh-mmc 0000:02:06.3: restoring config space at offset 0x0 (was 0x8431180, writing 0xffffffff)
ricoh-mmc: Resuming.
ricoh-mmc: Controller is now disabled.
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 2660.13 BogoMIPS (lpj=5320274)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
+[ds] using core 2 configuration
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
# Next message also appears during normal boot.
# Wonder if it is related to the APIC error now being fixed (see 15 lines down)?
+CPU1: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU U7700 @ 1.33GHz stepping 0d
CPU0 attaching NULL sched-domain.
Switched to high resolution mode on CPU 1
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
CPU1 is up
ACPI: Waking up from system sleep state S3
# Great that the next line is now gone.
-APIC error on CPU1: 00(40)
ACPI: EC: non-query interrupt received, switching to interrupt mode
# resume-early only has a config restore at offset 0x8 for the VGA controller;
# where does this one come from? And it is repeated later (see bottom of diff)!
+pci 0000:00:02.0: restoring config space at offset 0x1 (was 0x900403, writing 0x900003)
# Of the next 4 lines only the 3rd line also appears during normal boot.
+pci 0000:00:02.0: PME# disabled
+pci 0000:00:02.1: PME# disabled
+pci 0000:00:03.0: PME# disabled
+pci 0000:00:03.2: PME# disabled
e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
e1000e 0000:00:19.0: setting latency timer to 64
# Not a change, but still strange that next 2 lines are duplicated (similar
# to duplication during suspend above).
e1000e 0000:00:19.0: wake-up capability disabled by ACPI
e1000e 0000:00:19.0: PME# disabled
e1000e 0000:00:19.0: wake-up capability disabled by ACPI
e1000e 0000:00:19.0: PME# disabled
e1000e 0000:00:19.0: irq 26 for MSI/MSI-X
-uhci_hcd 0000:00:1a.0: enabling device (0000 -> 0001)
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
usb usb2: root hub lost power or was reset
-uhci_hcd 0000:00:1a.1: enabling device (0000 -> 0001)
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb3: root hub lost power or was reset
-ehci_hcd 0000:00:1a.7: enabling device (0000 -> 0002)
+ehci_hcd 0000:00:1a.7: PME# disabled
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
# Next line is duplicate from 3 lines up.
+ehci_hcd 0000:00:1a.7: PME# disabled
-HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
HDA Intel 0000:00:1b.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.1: setting latency timer to 64
-uhci_hcd 0000:00:1d.0: enabling device (0000 -> 0001)
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
usb usb5: root hub lost power or was reset
-uhci_hcd 0000:00:1d.1: enabling device (0000 -> 0001)
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1d.1: setting latency timer to 64
usb usb6: root hub lost power or was reset
-uhci_hcd 0000:00:1d.2: enabling device (0000 -> 0001)
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
usb usb7: root hub lost power or was reset
-ehci_hcd 0000:00:1d.7: enabling device (0000 -> 0002)
+ehci_hcd 0000:00:1d.7: PME# disabled
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:1d.7: setting latency timer to 64
# Next line is duplicate from 3 lines up. Same as 00:1a.7 above, again for ehci_hcd.
+ehci_hcd 0000:00:1d.7: PME# disabled
pci 0000:00:1e.0: setting latency timer to 64
# Duplicate config restore! Was already done during resume-early.
+ata_piix 0000:00:1f.1: restoring config space at offset 0x1 (was 0x2800005, writing 0x2880005)
ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ata_piix 0000:00:1f.1: setting latency timer to 64
ata2: port disabled. ignoring.
ACPI Exception (exoparg2-0445): AE_AML_PACKAGE_LIMIT, Index (000000005) is beyond end of object [20081204]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.C2C3] (Node ffff88007e01dea0), AE_AML_PACKAGE_LIMIT
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.C003.C0F6.C3F3._STM] (Node ffff88007e043de0), AE_AML_PACKAGE_LIMIT
ata1: ACPI set timing mode failed (status=0x300b)
-iwlagn 0000:10:00.0: enabling device (0000 -> 0002)
iwlagn 0000:10:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwlagn 0000:10:00.0: irq 27 for MSI/MSI-X
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[e0101000-e01017ff] Max Packet=[2048] IR/IT contexts=[4/4]
sdhci-pci 0000:02:06.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20
Registered led device: iwl-phy0:radio
Registered led device: iwl-phy0:assoc
Registered led device: iwl-phy0:RX
Registered led device: iwl-phy0:TX
sd 0:0:0:0: [sda] Starting disk
ata1.01: ACPI cmd ef/03:0c:00:00:00:b0 filtered out
ata1.01: ACPI cmd ef/03:40:00:00:00:b0 filtered out
ata1.00: ACPI cmd ef/03:01:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:45:00:00:00:a0 filtered out
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd c6/00:10:00:00:00:a0 succeeded
ata1.00: configured for UDMA/100
ata1.01: configured for MWDMA2
ata1.00: configured for UDMA/100
ata1.01: configured for MWDMA2
ata1: EH complete
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb 2-1: reset full speed USB device using uhci_hcd and address 2
usb 5-2: reset full speed USB device using uhci_hcd and address 2
# Is this line now missing because the INT is not disabled during suspend (see 1st comment)?
-pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
# Duplicate config restore for the VGA controller.
+pci 0000:00:02.0: restoring config space at offset 0x1 (was 0x900403, writing 0x900003)
pci 0000:00:02.0: setting latency timer to 64
Restarting tasks ... done.

"PME# disabled" messages displayed during normal boot
-----------------------------------------------------
pci 0000:00:03.0: PME# disabled
pci 0000:00:19.0: PME# disabled
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1d.7: PME# disabled
pci 0000:02:06.0: PME# disabled
pci 0000:02:06.1: PME# disabled
pci 0000:02:06.2: PME# disabled
pci 0000:02:06.3: PME# disabled
pci 0000:10:00.0: PME# disabled

Output of lspci (for reference)
-------------------------------
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
00:03.0 Communication controller: Intel Corporation Mobile PM965/GM965 MEI Controller (rev 0c)
00:03.2 IDE interface: Intel Corporation Mobile PM965/GM965 PT IDER Controller (rev 0c)
00:03.3 Serial controller: Intel Corporation Mobile PM965/GM965 KT Controller (rev 0c)
00:19.0 Ethernet controller: Intel Corporation 82566MM Gigabit Network Connection (rev 03)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
00:1f.0 ISA bridge: Intel Corporation 82801HBM (ICH8M-E) LPC Interface Controller (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03)
02:06.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba)
02:06.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04)
02:06.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21)
02:06.3 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev ff)
10:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)