* 2.6.29 on MacBook 2,1 fails to reboot @ 2009-03-30 2:04 Trenton Adams 2009-03-30 2:46 ` Morten P.D. Stevens 0 siblings, 1 reply; 15+ messages in thread From: Trenton Adams @ 2009-03-30 2:04 UTC (permalink / raw) To: Linux Kernel Mailing List Hi Guys, I am using v2.6.29 (x86_64 mode) on Linus' tree. I get to run level 6, where all processes have been killed, and the system is about to reboot, but it doesn't. No apparent error messages are printed out, it just hangs. I do the skinny elephant dance, and everything is fine. But, note that when doing "Elephant", it says that there are no more processes to kill. System information below. If you need more info, let me know. tdamac ~ # uname -a Linux tdamac 2.6.29 #3 SMP Sun Mar 29 19:07:55 MDT 2009 x86_64 Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz GenuineIntel GNU/Linux tdamac ~ # lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:07.0 Performance counters: Intel Corporation Device 27a3 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 01:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 22) 02:00.0 Network controller: Atheros Communications Inc. AR5418 802.11abgn Wireless PCI Express Adapter (rev 01) 03:03.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 61) tdamac ~ # cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping : 6 cpu MHz : 1000.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm tpr_shadow bogomips : 4322.42 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping : 6 cpu MHz : 1000.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm tpr_shadow bogomips : 4322.44 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: tdamac ~ # lsmod Module Size Used by i915 148744 2 drm 149184 3 i915 snd_pcm_oss 37728 0 snd_mixer_oss 14576 1 snd_pcm_oss snd_seq_oss 29056 0 snd_seq_midi_event 6608 1 snd_seq_oss snd_seq 48416 4 snd_seq_oss,snd_seq_midi_event snd_seq_device 6564 2 snd_seq_oss,snd_seq ipt_MASQUERADE 3024 1 iptable_nat 5392 1 nf_nat 18084 2 ipt_MASQUERADE,iptable_nat pl2303 17332 0 usbserial 30480 1 pl2303 hermes 6800 0 fuse 53424 0 cifs 222728 2 snd_hda_codec_idt 61392 1 snd_hda_intel 25096 3 snd_hda_codec 52368 2 snd_hda_codec_idt,snd_hda_intel snd_pcm 71576 3 snd_pcm_oss,snd_hda_intel,snd_hda_codec snd_timer 19808 2 snd_seq,snd_pcm snd 55272 16 snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_seq_device,snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer snd_page_alloc 8608 2 snd_hda_intel,snd_pcm appletouch 10676 0 pcspkr 2736 0 applesmc 29972 0 hwmon 2696 1 applesmc led_class 3672 1 applesmc input_polldev 3808 1 applesmc scsi_wait_scan 1360 0 Thanks. ^ permalink raw reply [flat|nested] 15+ messages in thread
* RE: 2.6.29 on MacBook 2,1 fails to reboot 2009-03-30 2:04 2.6.29 on MacBook 2,1 fails to reboot Trenton Adams @ 2009-03-30 2:46 ` Morten P.D. Stevens 2009-03-30 2:54 ` Trenton Adams 0 siblings, 1 reply; 15+ messages in thread From: Morten P.D. Stevens @ 2009-03-30 2:46 UTC (permalink / raw) To: 'Trenton Adams'; +Cc: 'Linux Kernel Mailing List' Hi, > System information below. If you need more info, let me know. Please post your dmesg output. -----Original Message----- From: linux-kernel-owner@vger.kernel.org [mailto:linux-kernel-owner@vger.kernel.org] On Behalf Of Trenton Adams Sent: Monday, March 30, 2009 4:04 AM To: Linux Kernel Mailing List Subject: 2.6.29 on MacBook 2,1 fails to reboot Hi Guys, I am using v2.6.29 (x86_64 mode) on Linus' tree. I get to run level 6, where all processes have been killed, and the system is about to reboot, but it doesn't. No apparent error messages are printed out, it just hangs. I do the skinny elephant dance, and everything is fine. But, note that when doing "Elephant", it says that there are no more processes to kill. System information below. If you need more info, let me know. tdamac ~ # uname -a Linux tdamac 2.6.29 #3 SMP Sun Mar 29 19:07:55 MDT 2009 x86_64 Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz GenuineIntel GNU/Linux tdamac ~ # lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:07.0 Performance counters: Intel Corporation Device 27a3 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 01:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 22) 02:00.0 Network controller: Atheros Communications Inc. AR5418 802.11abgn Wireless PCI Express Adapter (rev 01) 03:03.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 61) tdamac ~ # cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping : 6 cpu MHz : 1000.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm tpr_shadow bogomips : 4322.42 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping : 6 cpu MHz : 1000.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm tpr_shadow bogomips : 4322.44 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: tdamac ~ # lsmod Module Size Used by i915 148744 2 drm 149184 3 i915 snd_pcm_oss 37728 0 snd_mixer_oss 14576 1 snd_pcm_oss snd_seq_oss 29056 0 snd_seq_midi_event 6608 1 snd_seq_oss snd_seq 48416 4 snd_seq_oss,snd_seq_midi_event snd_seq_device 6564 2 snd_seq_oss,snd_seq ipt_MASQUERADE 3024 1 iptable_nat 5392 1 nf_nat 18084 2 ipt_MASQUERADE,iptable_nat pl2303 17332 0 usbserial 30480 1 pl2303 hermes 6800 0 fuse 53424 0 cifs 222728 2 snd_hda_codec_idt 61392 1 snd_hda_intel 25096 3 snd_hda_codec 52368 2 snd_hda_codec_idt,snd_hda_intel snd_pcm 71576 3 snd_pcm_oss,snd_hda_intel,snd_hda_codec snd_timer 19808 2 snd_seq,snd_pcm snd 55272 16 snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_seq_device,snd_hda_codec_i dt,snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer snd_page_alloc 8608 2 snd_hda_intel,snd_pcm appletouch 10676 0 pcspkr 2736 0 applesmc 29972 0 hwmon 2696 1 applesmc led_class 3672 1 applesmc input_polldev 3808 1 applesmc scsi_wait_scan 1360 0 Thanks. -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-03-30 2:46 ` Morten P.D. Stevens @ 2009-03-30 2:54 ` Trenton Adams 2009-03-30 3:17 ` Morten P.D. Stevens [not found] ` <897274600903292015n44005d12l82b0fafd170d6292@mail.gmail.com> 0 siblings, 2 replies; 15+ messages in thread From: Trenton Adams @ 2009-03-30 2:54 UTC (permalink / raw) To: Morten P.D. Stevens; +Cc: Linux Kernel Mailing List Oops, gmail doesn't reply to all by default. On Sun, Mar 29, 2009 at 8:46 PM, Morten P.D. Stevens <mstevens@win-professional.com> wrote: > Hi, > >> System information below. If you need more info, let me know. > > Please post your dmesg output. tdamac linux # dmesg Linux version 2.6.29 (root@tdamac) (gcc version 4.1.2 (Gentoo 4.1.2 p1.3)) #3 SMP Sun Mar 29 19:07:55 MDT 2009 Command line: root=/dev/ram0 init=/linuxrc real_root=/dev/s/sys dolvm KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007e08c000 (usable) BIOS-e820: 000000007e08c000 - 000000007e28d000 (ACPI NVS) BIOS-e820: 000000007e28d000 - 000000007eebe000 (ACPI data) BIOS-e820: 000000007eebe000 - 000000007eeef000 (ACPI NVS) BIOS-e820: 000000007eeef000 - 000000007ef00000 (ACPI data) BIOS-e820: 000000007ef00000 - 0000000080000000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) DMI 2.4 present. last_pfn = 0x7e08c max_arch_pfn = 0x100000000 init_memory_mapping: 0000000000000000-000000007e08c000 0000000000 - 007e000000 page 2M 007e000000 - 007e08c000 page 4k kernel direct mapping tables up to 7e08c000 @ 8000-c000 last_map_addr: 7e08c000 end: 7e08c000 RAMDISK: 37edf000 - 37fef088 ACPI: RSDP 000FE020, 0024 (r2 APPLE ) ACPI: XSDT 7EEFD1C0, 0074 (r1 APPLE Apple00 A5 1000013) ACPI: FACP 7EEFB000, 00F4 (r3 APPLE Apple00 A5 Loki 5F) FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) ACPI: DSDT 7EEF0000, 41E4 (r1 APPLE MacBook 20001 INTL 20050309) ACPI: FACS 7EEC0000, 0040 ACPI: HPET 7EEFA000, 0038 (r1 APPLE Apple00 1 Loki 5F) ACPI: APIC 7EEF9000, 0068 (r1 APPLE Apple00 1 Loki 5F) ACPI: MCFG 7EEF8000, 003C (r1 APPLE Apple00 1 Loki 5F) ACPI: ASF! 7EEF7000, 00A0 (r32 APPLE Apple00 1 Loki 5F) ACPI: SBST 7EEF6000, 0030 (r1 APPLE Apple00 1 Loki 5F) ACPI: ECDT 7EEF5000, 0053 (r1 APPLE Apple00 1 Loki 5F) ACPI: SSDT 7EEEF000, 04DC (r1 APPLE CpuPm 3000 INTL 20050309) ACPI: SSDT 7EEBD000, 064F (r1 SataRe SataPri 1000 INTL 20050309) ACPI: SSDT 7EEBC000, 069C (r1 SataRe SataSec 1000 INTL 20050309) ACPI: Local APIC address 0xfee00000 (6 early reservations) ==> bootmem [0000000000 - 007e08c000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] #2 [0000200000 - 0000a43b8c] TEXT DATA BSS ==> [0000200000 - 0000a43b8c] #3 [0037edf000 - 0037fef088] RAMDISK ==> [0037edf000 - 0037fef088] #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] #5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000] [ffffe20000000000-ffffe20001bfffff] PMD -> [ffff880001200000-ffff880002dfffff] on node 0 Zone PFN ranges: DMA 0x00000000 -> 0x00001000 DMA32 0x00001000 -> 0x00100000 Normal 0x00100000 -> 0x00100000 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000000 -> 0x0000009f 0: 0x00000100 -> 0x0007e08c On node 0 totalpages: 516139 DMA zone: 56 pages used for memmap DMA zone: 2216 pages reserved DMA zone: 1727 pages, LIFO batch:0 DMA32 zone: 7002 pages used for memmap DMA32 zone: 505138 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Using ACPI (MADT) for SMP configuration information ACPI: HPET id: 0x8086a201 base: 0xfed00000 SMP: Allowing 2 CPUs, 0 hotplug CPUs nr_irqs_gsi: 24 Allocating PCI resources starting at 88000000 (gap: 80000000:70000000) NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1 PERCPU: Allocating 53248 bytes of per cpu data Built 1 zonelists in Zone order, mobility grouping on. Total pages: 506865 Kernel command line: root=/dev/ram0 init=/linuxrc real_root=/dev/s/sys dolvm Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Extended CMOS year: 2000 Fast TSC calibration failed TSC: Unable to calibrate against PIT TSC: using PMTIMER reference calibration Detected 2161.212 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Checking aperture... No AGP bridge found Memory: 2022216k/2064944k available (4392k kernel code, 388k absent, 41684k reserved, 2619k data, 372k init) SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 hpet clockevent registered HPET: 3 timers in total, 0 timers will be used for per-cpu timer Calibrating delay loop (skipped), value calculated using timer frequency.. 4322.42 BogoMIPS (lpj=8644848) Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K [ds] using Core 2/Atom configuration CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU0: Thermal monitoring enabled (TM2) using mwait in idle threads. ACPI: Core revision 20081204 Setting APIC routing to flat ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping 06 Booting processor 1 APIC 0x1 ip 0x6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4322.44 BogoMIPS (lpj=8644898) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K [ds] using Core 2/Atom configuration CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU1: Thermal monitoring enabled (TM2) CPU1: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs Total of 2 processors activated (8644.87 BogoMIPS). net_namespace: 1784 bytes NET: Registered protocol family 16 ACPI: bus type pci registered PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 PCI: MCFG area at f0000000 reserved in E820 PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 PCI: Using MMCONFIG at f0000000 - f3ffffff PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0 ACPI: EC: EC description table is found, configuring boot EC ACPI: EC: non-query interrupt received, switching to interrupt mode ACPI: BIOS _OSI(Linux) query ignored ACPI: Interpreter enabled ACPI: (supports S0 S3 S5) ACPI: Using IOAPIC for interrupt routing ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62 ACPI: EC: driver started in interrupt mode ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:02.0: reg 10 32bit mmio: [0x90380000-0x903fffff] pci 0000:00:02.0: reg 14 io port: [0x20e0-0x20e7] pci 0000:00:02.0: reg 18 32bit mmio: [0x80000000-0x8fffffff] pci 0000:00:02.0: reg 1c 32bit mmio: [0x90400000-0x9043ffff] pci 0000:00:02.1: reg 10 32bit mmio: [0x90300000-0x9037ffff] pci 0000:00:07.0: reg 10 32bit mmio: [0x90444000-0x90444fff] pci 0000:00:1b.0: reg 10 64bit mmio: [0x90440000-0x90443fff] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold pci 0000:00:1b.0: PME# disabled pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold pci 0000:00:1c.1: PME# disabled pci 0000:00:1d.0: reg 20 io port: [0x2080-0x209f] pci 0000:00:1d.1: reg 20 io port: [0x2060-0x207f] pci 0000:00:1d.2: reg 20 io port: [0x2040-0x205f] pci 0000:00:1d.3: reg 20 io port: [0x2020-0x203f] pci 0000:00:1d.7: reg 10 32bit mmio: [0x90445400-0x904457ff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 000f) pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 1640 (mask 000f) pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 0300 (mask 001f) pci 0000:00:1f.1: reg 10 io port: [0x20d8-0x20df] pci 0000:00:1f.1: reg 14 io port: [0x20f4-0x20f7] pci 0000:00:1f.1: reg 18 io port: [0x20d0-0x20d7] pci 0000:00:1f.1: reg 1c io port: [0x20f0-0x20f3] pci 0000:00:1f.1: reg 20 io port: [0x20b0-0x20bf] pci 0000:00:1f.2: reg 10 io port: [0x20c8-0x20cf] pci 0000:00:1f.2: reg 14 io port: [0x20ec-0x20ef] pci 0000:00:1f.2: reg 18 io port: [0x20c0-0x20c7] pci 0000:00:1f.2: reg 1c io port: [0x20e8-0x20eb] pci 0000:00:1f.2: reg 20 io port: [0x20a0-0x20af] pci 0000:00:1f.2: reg 24 32bit mmio: [0x90445000-0x904453ff] pci 0000:00:1f.2: PME# supported from D3hot pci 0000:00:1f.2: PME# disabled pci 0000:00:1f.3: reg 20 io port: [0xefa0-0xefbf] pci 0000:01:00.0: reg 10 64bit mmio: [0x90200000-0x90203fff] pci 0000:01:00.0: reg 18 io port: [0x1000-0x10ff] pci 0000:01:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff] pci 0000:01:00.0: supports D1 D2 pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:01:00.0: PME# disabled pci 0000:00:1c.0: bridge io port: [0x1000-0x1fff] pci 0000:00:1c.0: bridge 32bit mmio: [0x90200000-0x902fffff] pci 0000:02:00.0: reg 10 64bit mmio: [0x90100000-0x9010ffff] pci 0000:02:00.0: supports D1 pci 0000:02:00.0: PME# supported from D0 D1 D3hot pci 0000:02:00.0: PME# disabled pci 0000:00:1c.1: bridge 32bit mmio: [0x90100000-0x901fffff] pci 0000:03:03.0: reg 10 32bit mmio: [0x90000000-0x90000fff] pci 0000:03:03.0: supports D1 D2 pci 0000:03:03.0: PME# supported from D0 D1 D2 D3hot pci 0000:03:03.0: PME# disabled pci 0000:00:1e.0: transparent bridge pci 0000:00:1e.0: bridge 32bit mmio: [0x90000000-0x900fffff] pci_bus 0000:00: on NUMA node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15) SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 comparators, 64-bit 14.318180 MHz counter pnp: PnP ACPI init ACPI: bus type pnp registered pnp 00:07: io resource (0x1640-0x164f) overlaps 0000:00:1c.0 BAR 7 (0x1000-0x1fff), disabling pnp: PnP ACPI: found 9 devices ACPI: ACPI bus type pnp unregistered system 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved system 00:01: iomem range 0xfed20000-0xfed8ffff has been reserved system 00:05: iomem range 0xfed00000-0xfed003ff has been reserved system 00:07: ioport range 0x680-0x6ef has been reserved system 00:07: ioport range 0x800-0x80f has been reserved system 00:07: ioport range 0x810-0x817 has been reserved system 00:07: ioport range 0x400-0x47f has been reserved system 00:07: ioport range 0x500-0x53f has been reserved pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01 pci 0000:00:1c.0: IO window: 0x1000-0x1fff pci 0000:00:1c.0: MEM window: 0x90200000-0x902fffff pci 0000:00:1c.0: PREFETCH window: 0x00000090500000-0x000000905fffff pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02 pci 0000:00:1c.1: IO window: disabled pci 0000:00:1c.1: MEM window: 0x90100000-0x901fffff pci 0000:00:1c.1: PREFETCH window: disabled pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03 pci 0000:00:1e.0: IO window: disabled pci 0000:00:1e.0: MEM window: 0x90000000-0x900fffff pci 0000:00:1e.0: PREFETCH window: disabled pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:1c.1: setting latency timer to 64 pci 0000:00:1e.0: power state changed by ACPI to D0 pci 0000:00:1e.0: setting latency timer to 64 pci_bus 0000:00: resource 0 io: [0x00-0xffff] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] pci_bus 0000:01: resource 0 io: [0x1000-0x1fff] pci_bus 0000:01: resource 1 mem: [0x90200000-0x902fffff] pci_bus 0000:01: resource 2 mem: [0x90500000-0x905fffff] pci_bus 0000:01: resource 3 mem: [0x0-0x0] pci_bus 0000:02: resource 0 mem: [0x0-0x0] pci_bus 0000:02: resource 1 mem: [0x90100000-0x901fffff] pci_bus 0000:02: resource 2 mem: [0x0-0x0] pci_bus 0000:02: resource 3 mem: [0x0-0x0] pci_bus 0000:03: resource 0 mem: [0x0-0x0] pci_bus 0000:03: resource 1 mem: [0x90000000-0x900fffff] pci_bus 0000:03: resource 2 mem: [0x0-0x0] pci_bus 0000:03: resource 3 io: [0x00-0xffff] pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Freeing initrd memory: 1088k freed Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba HugeTLB registered 2 MB page size, pre-allocated 0 pages Installing knfsd (copyright (C) 1996 okir@monad.swb.de). msgmni has been set to 3953 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci 0000:00:02.0: Boot video device ACPI: AC Adapter [ADP1] (on-line) Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 ACPI: Battery Slot [BAT0] (battery present) input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Lid Switch as /class/input/input1 ACPI: Lid Switch [LID0] input: Power Button (CM) as /class/input/input2 ACPI: Power Button (CM) [PWRB] input: Sleep Button (CM) as /class/input/input3 ACPI: Sleep Button (CM) [SLPB] ACPI: SSDT 7EEB8C10, 02AE (r1 APPLE Cpu0Ist 3000 INTL 20050309) ACPI: SSDT 7EEB8910, 02A0 (r1 APPLE Cpu0Cst 3001 INTL 20050309) Monitor-Mwait will be used to enter C-1 state Monitor-Mwait will be used to enter C-2 state Monitor-Mwait will be used to enter C-3 state ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) processor ACPI_CPU:00: registered as cooling_device0 ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: SSDT 7EEB8F10, 0087 (r1 APPLE Cpu1Ist 3000 INTL 20050309) ACPI: SSDT 7EEB7F10, 0085 (r1 APPLE Cpu1Cst 3000 INTL 20050309) ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) processor ACPI_CPU:01: registered as cooling_device1 ACPI: Processor [CPU1] (supports 8 throttling states) Real Time Clock Driver v1.12b intel_rng: FWH not detected Linux agpgart interface v0.103 agpgart-intel 0000:00:00.0: Intel 945GM Chipset agpgart-intel 0000:00:00.0: detected 16124K stolen memory agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000 intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/945GME/965G/965GM chipsets intelfb: Version 0.9.6 intelfb 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 intelfb: 00:02.0: Intel(R) 945GM, aperture size 256MB, stolen memory 16124kB intelfb: Non-CRT device is enabled ( LVDS port ). Disabling mode switching. intelfb: Video mode must be programmed at boot time. Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled floppy0: no floppy controllers found brd: module loaded loop: module loaded Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI Copyright (c) 1999-2006 Intel Corporation. e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI e100: Copyright(c) 1999-2006 Intel Corporation sky2 driver version 1.22 sky2 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 sky2 0000:01:00.0: setting latency timer to 64 sky2 0000:01:00.0: Yukon-2 EC chip revision 2 sky2 0000:01:00.0: Marvell Yukon 88E8053 Gigabit Ethernet Controller Part Number: Yukon 88E8053 Engineering Level: Rev. 2.2 Manufacturer: Marvell sky2 0000:01:00.0: irq 24 for MSI/MSI-X sky2 eth0: addr 00:19:e3:43:1c:a3 console [netcon0] enabled netconsole: network logging started Linux video capture interface: v2.00 usbcore: registered new interface driver uvcvideo USB Video Class driver (v0.1.0) Uniform Multi-Platform E-IDE driver piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x02) pci 0000:00:1f.1: power state changed by ACPI to D0 pci 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 piix 0000:00:1f.1: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x20b0-0x20b7 ide1: BM-DMA at 0x20b8-0x20bf Probing IDE interface ide0... hda: HL-DT-ST DVDRW GSA-S10N, ATAPI CD/DVD-ROM drive hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 hda: UDMA/33 mode selected Probing IDE interface ide1... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports ide-gd driver 1.18 ide-cd driver 5.00 ide-cd: hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 3ware Storage Controller device driver for Linux v1.26.02.002. Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods ata_piix 0000:00:1f.2: version 2.12 ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 ata_piix 0000:00:1f.2: MAP [ P0 P2 -- -- ] ata_piix 0000:00:1f.2: setting latency timer to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: SATA max UDMA/133 cmd 0x20c8 ctl 0x20ec bmdma 0x20a0 irq 19 ata2: SATA max UDMA/133 cmd 0x20c0 ctl 0x20e8 bmdma 0x20a8 irq 19 ata1.01: ATA-7: ST9160821AS, 3.CAE, max UDMA/133 ata1.01: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32) ata1.01: configured for UDMA/133 isa bounce pool size: 16 pages scsi 0:0:1:0: Direct-Access ATA ST9160821AS 3.CA PQ: 0 ANSI: 5 sd 0:0:1:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) sd 0:0:1:0: [sda] Write Protect is off sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:1:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) sd 0:0:1:0: [sda] Write Protect is off sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sd 0:0:1:0: [sda] Attached SCSI disk sd 0:0:1:0: Attached scsi generic sg0 type 0 Fusion MPT base driver 3.04.07 Copyright (c) 1999-2008 LSI Corporation Fusion MPT SPI Host driver 3.04.07 ohci1394 0000:03:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[19] MMIO=[90000000-900007ff] Max Packet=[2048] IR/IT contexts=[8/8] ieee1394: raw1394: /dev/raw1394 device initialized ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 21 (level, low) -> IRQ 21 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported ehci_hcd 0000:00:1d.7: irq 21, io mem 0x90445400 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver uhci_hcd: USB Universal Host Controller Interface driver uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 21, io base 0x00002080 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1d.3: setting latency timer to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002020 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: No PS/2 controller found. Probing ports directly. i8042.c: No controller found. mice: PS/2 mouse device common for all mice device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com cpuidle: using governor ladder cpuidle: using governor menu Marking TSC unstable due to TSC halts in idle usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver oprofile: using NMI interrupt. Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (16384 buckets, 65536 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. xt_time: kernel timezone is -0000 ip_tables: (C) 2000-2006 Netfilter Core Team arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. registered taskstats version 1 Freeing unused kernel memory: 372k freed usb 1-1: new high speed USB device using ehci_hcd and address 2 usb 1-1: configuration #1 chosen from 1 choice scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usb 1-3: new high speed USB device using ehci_hcd and address 4 usb 1-3: configuration #1 chosen from 1 choice hub 1-3:1.0: USB hub found hub 1-3:1.0: 2 ports detected Clocksource tsc unstable (delta = -265511863 ns) usb 1-4: new high speed USB device using ehci_hcd and address 5 usb 1-4: configuration #1 chosen from 1 choice ieee1394: Host added: ID:BUS[0-00:1023] GUID[001cb3fffe8ab416] usb 2-2: new full speed USB device using uhci_hcd and address 2 usb 2-2: configuration #1 chosen from 1 choice input: Apple Computer Apple Internal Keyboard / Trackpad as /class/input/input4 apple 0003:05AC:021A.0001: input: USB HID v1.11 Keyboard [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2/input0 input: Apple Computer Apple Internal Keyboard / Trackpad as /class/input/input5 apple 0003:05AC:021A.0002: input: USB HID v1.11 Device [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2/input2 usb 4-2: new full speed USB device using uhci_hcd and address 2 usb 4-2: configuration #1 chosen from 1 choice generic-usb 0003:05AC:8240.0003: claimed by neither input, hiddev nor hidraw usb 5-1: new full speed USB device using uhci_hcd and address 2 usb 5-1: configuration #1 chosen from 1 choice input: HID 05ac:1000 as /class/input/input6 generic-usb 0003:05AC:1000.0004: input: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0000:00:1d.3-1/input0 input: HID 05ac:1000 as /class/input/input7 generic-usb 0003:05AC:1000.0005: input: USB HID v1.11 Mouse [HID 05ac:1000] on usb-0000:00:1d.3-1/input1 usb 1-3.1: new high speed USB device using ehci_hcd and address 8 usb 1-3.1: configuration #1 chosen from 1 choice hub 1-3.1:1.0: USB hub found hub 1-3.1:1.0: 4 ports detected usb 1-3.2: new low speed USB device using ehci_hcd and address 9 usb 1-3.2: configuration #1 chosen from 1 choice input: Logitech USB Mouse as /class/input/input8 generic-usb 0003:046D:C00C.0006: input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:1d.7-3.2/input0 usb 1-3.1.1: new high speed USB device using ehci_hcd and address 10 usb 1-3.1.1: configuration #1 chosen from 1 choice scsi3 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 10 usb-storage: waiting for device to settle before scanning usb 1-3.1.3: new high speed USB device using ehci_hcd and address 11 usb 1-3.1.3: configuration #1 chosen from 1 choice hub 1-3.1.3:1.0: USB hub found hub 1-3.1.3:1.0: 3 ports detected usb 1-3.1.4: new high speed USB device using ehci_hcd and address 12 usb 1-3.1.4: configuration #1 chosen from 1 choice scsi4 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 12 usb-storage: waiting for device to settle before scanning usb 1-3.1.3.1: new low speed USB device using ehci_hcd and address 13 usb 1-3.1.3.1: configuration #1 chosen from 1 choice input: No brand KVM as /class/input/input9 generic-usb 0003:10D5:5552.0007: input: USB HID v1.10 Keyboard [No brand KVM] on usb-0000:00:1d.7-3.1.3.1/input0 input: No brand KVM as /class/input/input10 generic-usb 0003:10D5:5552.0008: input: USB HID v1.10 Mouse [No brand KVM] on usb-0000:00:1d.7-3.1.3.1/input1 scsi 2:0:0:0: Direct-Access Ext Hard Disk PQ: 0 ANSI: 4 sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 10 00 00 00 sd 2:0:0:0: [sdb] Assuming drive cache: write through sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 10 00 00 00 sd 2:0:0:0: [sdb] Assuming drive cache: write through sdb: sdb1 < sdb5 sdb6 > sd 2:0:0:0: [sdb] Attached SCSI disk sd 2:0:0:0: Attached scsi generic sg1 type 0 usb-storage: device scan complete kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. udev: renamed network interface eth0 to eth1 scsi 3:0:0:0: Direct-Access Generic Flash HS-CF 4.44 PQ: 0 ANSI: 0 sd 3:0:0:0: [sdc] Attached SCSI removable disk sd 3:0:0:0: Attached scsi generic sg2 type 0 usb-storage: device scan complete applesmc: Apple MacBook (v2) detected: applesmc: - Model with accelerometer applesmc: - Model without light sensors and backlight applesmc: - Model with 10 temperature sensors applesmc: device has already been initialized (0xe0, 0xf8). applesmc: device successfully initialized. applesmc: 1 fans found. input: applesmc as /class/input/input11 applesmc: driver successfully loaded. input: PC Speaker as /class/input/input12 scsi 4:0:0:0: Direct-Access Maxtor 6 L200R0 BAH4 PQ: 0 ANSI: 0 sd 4:0:0:0: [sdd] 398297087 512-byte hardware sectors: (203 GB/189 GiB) sd 4:0:0:0: [sdd] Write Protect is off sd 4:0:0:0: [sdd] Mode Sense: 03 00 00 00 sd 4:0:0:0: [sdd] Assuming drive cache: write through sd 4:0:0:0: [sdd] 398297087 512-byte hardware sectors: (203 GB/189 GiB) sd 4:0:0:0: [sdd] Write Protect is off sd 4:0:0:0: [sdd] Mode Sense: 03 00 00 00 sd 4:0:0:0: [sdd] Assuming drive cache: write through sdd: sdd1 sd 4:0:0:0: [sdd] Attached SCSI disk sd 4:0:0:0: Attached scsi generic sg3 type 0 usb-storage: device scan complete appletouch: Geyser mode initialized. input: appletouch as /class/input/input13 usbcore: registered new interface driver appletouch HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 HDA Intel 0000:00:1b.0: setting latency timer to 64 hda_codec: STAC922x, Apple subsys_id=106b2200 input: HDA Intel Line In at Ext Left Jack as /class/input/input14 input: HDA Intel Mic at Ext Left Jack as /class/input/input15 input: HDA Intel HP Out at Ext Left Jack as /class/input/input16 EXT3 FS on dm-2, internal journal fuse init (API version 7.11) usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 pl2303: Prolific PL2303 USB to serial adaptor driver EXT4-fs: barriers enabled kjournald2 starting: pid 4443, dev dm-0:8, commit interval 5 seconds EXT4 FS on dm-0, internal journal on dm-0:8 EXT4-fs: delayed allocation enabled EXT4-fs: mballoc enabled EXT4-fs: mounted filesystem dm-0 with ordered data mode EXT4-fs: barriers enabled kjournald2 starting: pid 4444, dev dm-4:8, commit interval 5 seconds EXT4 FS on dm-4, internal journal on dm-4:8 EXT4-fs: delayed allocation enabled EXT4-fs: mballoc enabled EXT4-fs: mounted filesystem dm-4 with ordered data mode EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended Adding 1048568k swap on /dev/mapper/s-swap. Priority:-1 extents:1 across:1048568k sky2 eth1: enabling interface ADDRCONF(NETDEV_UP): eth1: link is not ready sky2 eth1: Link is up at 1000 Mbps, full duplex, flow control both ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready eth1: no IPv6 routers present [drm] Initialized drm 1.1.0 20060810 pci 0000:00:02.0: setting latency timer to 64 [drm] Initialized i915 1.6.0 20080730 on minor 0 JBD: barrier-based sync failed on dm-0:8 - disabling barriers CE: hpet increasing min_delta_ns to 15000 nsec ACPI: EC: GPE storm detected, transactions will use polling mode ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-03-30 2:54 ` Trenton Adams @ 2009-03-30 3:17 ` Morten P.D. Stevens [not found] ` <897274600903292015n44005d12l82b0fafd170d6292@mail.gmail.com> 1 sibling, 0 replies; 15+ messages in thread From: Morten P.D. Stevens @ 2009-03-30 3:17 UTC (permalink / raw) To: Trenton Adams; +Cc: Linux Kernel Mailing List Hi, at first view your dmesg should be okay. does it reboot with 2.6.28 or lower? Morten 2009/3/30 Trenton Adams <trenton.d.adams@gmail.com> > > Oops, gmail doesn't reply to all by default. > > On Sun, Mar 29, 2009 at 8:46 PM, Morten P.D. Stevens > <mstevens@win-professional.com> wrote: > > Hi, > > > >> System information below. If you need more info, let me know. > > > > Please post your dmesg output. > > tdamac linux # dmesg > Linux version 2.6.29 (root@tdamac) (gcc version 4.1.2 (Gentoo 4.1.2 > p1.3)) #3 SMP Sun Mar 29 19:07:55 MDT 2009 > Command line: root=/dev/ram0 init=/linuxrc real_root=/dev/s/sys dolvm > KERNEL supported cpus: > Intel GenuineIntel > AMD AuthenticAMD > Centaur CentaurHauls > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000007e08c000 (usable) > BIOS-e820: 000000007e08c000 - 000000007e28d000 (ACPI NVS) > BIOS-e820: 000000007e28d000 - 000000007eebe000 (ACPI data) > BIOS-e820: 000000007eebe000 - 000000007eeef000 (ACPI NVS) > BIOS-e820: 000000007eeef000 - 000000007ef00000 (ACPI data) > BIOS-e820: 000000007ef00000 - 0000000080000000 (reserved) > BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) > BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) > BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved) > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) > DMI 2.4 present. > last_pfn = 0x7e08c max_arch_pfn = 0x100000000 > init_memory_mapping: 0000000000000000-000000007e08c000 > 0000000000 - 007e000000 page 2M > 007e000000 - 007e08c000 page 4k > kernel direct mapping tables up to 7e08c000 @ 8000-c000 > last_map_addr: 7e08c000 end: 7e08c000 > RAMDISK: 37edf000 - 37fef088 > ACPI: RSDP 000FE020, 0024 (r2 APPLE ) > ACPI: XSDT 7EEFD1C0, 0074 (r1 APPLE Apple00 A5 1000013) > ACPI: FACP 7EEFB000, 00F4 (r3 APPLE Apple00 A5 Loki 5F) > FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) > ACPI: DSDT 7EEF0000, 41E4 (r1 APPLE MacBook 20001 INTL 20050309) > ACPI: FACS 7EEC0000, 0040 > ACPI: HPET 7EEFA000, 0038 (r1 APPLE Apple00 1 Loki 5F) > ACPI: APIC 7EEF9000, 0068 (r1 APPLE Apple00 1 Loki 5F) > ACPI: MCFG 7EEF8000, 003C (r1 APPLE Apple00 1 Loki 5F) > ACPI: ASF! 7EEF7000, 00A0 (r32 APPLE Apple00 1 Loki 5F) > ACPI: SBST 7EEF6000, 0030 (r1 APPLE Apple00 1 Loki 5F) > ACPI: ECDT 7EEF5000, 0053 (r1 APPLE Apple00 1 Loki 5F) > ACPI: SSDT 7EEEF000, 04DC (r1 APPLE CpuPm 3000 INTL 20050309) > ACPI: SSDT 7EEBD000, 064F (r1 SataRe SataPri 1000 INTL 20050309) > ACPI: SSDT 7EEBC000, 069C (r1 SataRe SataSec 1000 INTL 20050309) > ACPI: Local APIC address 0xfee00000 > (6 early reservations) ==> bootmem [0000000000 - 007e08c000] > #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] > #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] > #2 [0000200000 - 0000a43b8c] TEXT DATA BSS ==> [0000200000 - 0000a43b8c] > #3 [0037edf000 - 0037fef088] RAMDISK ==> [0037edf000 - 0037fef088] > #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] > #5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000] > [ffffe20000000000-ffffe20001bfffff] PMD -> > [ffff880001200000-ffff880002dfffff] on node 0 > Zone PFN ranges: > DMA 0x00000000 -> 0x00001000 > DMA32 0x00001000 -> 0x00100000 > Normal 0x00100000 -> 0x00100000 > Movable zone start PFN for each node > early_node_map[2] active PFN ranges > 0: 0x00000000 -> 0x0000009f > 0: 0x00000100 -> 0x0007e08c > On node 0 totalpages: 516139 > DMA zone: 56 pages used for memmap > DMA zone: 2216 pages reserved > DMA zone: 1727 pages, LIFO batch:0 > DMA32 zone: 7002 pages used for memmap > DMA32 zone: 505138 pages, LIFO batch:31 > ACPI: PM-Timer IO Port: 0x408 > ACPI: Local APIC address 0xfee00000 > ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) > ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) > ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) > ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) > IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23 > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > ACPI: IRQ0 used by override. > ACPI: IRQ2 used by override. > ACPI: IRQ9 used by override. > Using ACPI (MADT) for SMP configuration information > ACPI: HPET id: 0x8086a201 base: 0xfed00000 > SMP: Allowing 2 CPUs, 0 hotplug CPUs > nr_irqs_gsi: 24 > Allocating PCI resources starting at 88000000 (gap: 80000000:70000000) > NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1 > PERCPU: Allocating 53248 bytes of per cpu data > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 506865 > Kernel command line: root=/dev/ram0 init=/linuxrc real_root=/dev/s/sys dolvm > Initializing CPU#0 > PID hash table entries: 4096 (order: 12, 32768 bytes) > Extended CMOS year: 2000 > Fast TSC calibration failed > TSC: Unable to calibrate against PIT > TSC: using PMTIMER reference calibration > Detected 2161.212 MHz processor. > Console: colour VGA+ 80x25 > console [tty0] enabled > Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) > Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) > Checking aperture... > No AGP bridge found > Memory: 2022216k/2064944k available (4392k kernel code, 388k absent, > 41684k reserved, 2619k data, 372k init) > SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 > hpet clockevent registered > HPET: 3 timers in total, 0 timers will be used for per-cpu timer > Calibrating delay loop (skipped), value calculated using timer > frequency.. 4322.42 BogoMIPS (lpj=8644848) > Mount-cache hash table entries: 256 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 4096K > [ds] using Core 2/Atom configuration > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 0 > CPU0: Thermal monitoring enabled (TM2) > using mwait in idle threads. > ACPI: Core revision 20081204 > Setting APIC routing to flat > ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 > CPU0: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping 06 > Booting processor 1 APIC 0x1 ip 0x6000 > Initializing CPU#1 > Calibrating delay using timer specific routine.. 4322.44 BogoMIPS (lpj=8644898) > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 4096K > [ds] using Core 2/Atom configuration > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 1 > CPU1: Thermal monitoring enabled (TM2) > CPU1: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping 06 > checking TSC synchronization [CPU#0 -> CPU#1]: passed. > Brought up 2 CPUs > Total of 2 processors activated (8644.87 BogoMIPS). > net_namespace: 1784 bytes > NET: Registered protocol family 16 > ACPI: bus type pci registered > PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 > PCI: MCFG area at f0000000 reserved in E820 > PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 > PCI: Using MMCONFIG at f0000000 - f3ffffff > PCI: Using configuration type 1 for base access > bio: create slab <bio-0> at 0 > ACPI: EC: EC description table is found, configuring boot EC > ACPI: EC: non-query interrupt received, switching to interrupt mode > ACPI: BIOS _OSI(Linux) query ignored > ACPI: Interpreter enabled > ACPI: (supports S0 S3 S5) > ACPI: Using IOAPIC for interrupt routing > ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62 > ACPI: EC: driver started in interrupt mode > ACPI: No dock devices found. > ACPI: PCI Root Bridge [PCI0] (0000:00) > pci 0000:00:02.0: reg 10 32bit mmio: [0x90380000-0x903fffff] > pci 0000:00:02.0: reg 14 io port: [0x20e0-0x20e7] > pci 0000:00:02.0: reg 18 32bit mmio: [0x80000000-0x8fffffff] > pci 0000:00:02.0: reg 1c 32bit mmio: [0x90400000-0x9043ffff] > pci 0000:00:02.1: reg 10 32bit mmio: [0x90300000-0x9037ffff] > pci 0000:00:07.0: reg 10 32bit mmio: [0x90444000-0x90444fff] > pci 0000:00:1b.0: reg 10 64bit mmio: [0x90440000-0x90443fff] > pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold > pci 0000:00:1b.0: PME# disabled > pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold > pci 0000:00:1c.0: PME# disabled > pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold > pci 0000:00:1c.1: PME# disabled > pci 0000:00:1d.0: reg 20 io port: [0x2080-0x209f] > pci 0000:00:1d.1: reg 20 io port: [0x2060-0x207f] > pci 0000:00:1d.2: reg 20 io port: [0x2040-0x205f] > pci 0000:00:1d.3: reg 20 io port: [0x2020-0x203f] > pci 0000:00:1d.7: reg 10 32bit mmio: [0x90445400-0x904457ff] > pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold > pci 0000:00:1d.7: PME# disabled > pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO > pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO > pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 000f) > pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 1640 (mask 000f) > pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 0300 (mask 001f) > pci 0000:00:1f.1: reg 10 io port: [0x20d8-0x20df] > pci 0000:00:1f.1: reg 14 io port: [0x20f4-0x20f7] > pci 0000:00:1f.1: reg 18 io port: [0x20d0-0x20d7] > pci 0000:00:1f.1: reg 1c io port: [0x20f0-0x20f3] > pci 0000:00:1f.1: reg 20 io port: [0x20b0-0x20bf] > pci 0000:00:1f.2: reg 10 io port: [0x20c8-0x20cf] > pci 0000:00:1f.2: reg 14 io port: [0x20ec-0x20ef] > pci 0000:00:1f.2: reg 18 io port: [0x20c0-0x20c7] > pci 0000:00:1f.2: reg 1c io port: [0x20e8-0x20eb] > pci 0000:00:1f.2: reg 20 io port: [0x20a0-0x20af] > pci 0000:00:1f.2: reg 24 32bit mmio: [0x90445000-0x904453ff] > pci 0000:00:1f.2: PME# supported from D3hot > pci 0000:00:1f.2: PME# disabled > pci 0000:00:1f.3: reg 20 io port: [0xefa0-0xefbf] > pci 0000:01:00.0: reg 10 64bit mmio: [0x90200000-0x90203fff] > pci 0000:01:00.0: reg 18 io port: [0x1000-0x10ff] > pci 0000:01:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff] > pci 0000:01:00.0: supports D1 D2 > pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold > pci 0000:01:00.0: PME# disabled > pci 0000:00:1c.0: bridge io port: [0x1000-0x1fff] > pci 0000:00:1c.0: bridge 32bit mmio: [0x90200000-0x902fffff] > pci 0000:02:00.0: reg 10 64bit mmio: [0x90100000-0x9010ffff] > pci 0000:02:00.0: supports D1 > pci 0000:02:00.0: PME# supported from D0 D1 D3hot > pci 0000:02:00.0: PME# disabled > pci 0000:00:1c.1: bridge 32bit mmio: [0x90100000-0x901fffff] > pci 0000:03:03.0: reg 10 32bit mmio: [0x90000000-0x90000fff] > pci 0000:03:03.0: supports D1 D2 > pci 0000:03:03.0: PME# supported from D0 D1 D2 D3hot > pci 0000:03:03.0: PME# disabled > pci 0000:00:1e.0: transparent bridge > pci 0000:00:1e.0: bridge 32bit mmio: [0x90000000-0x900fffff] > pci_bus 0000:00: on NUMA node 0 > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] > ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 > ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15) > ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 > ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15) > ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled. > ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled. > ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15) > ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15) > SCSI subsystem initialized > libata version 3.00 loaded. > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > PCI: Using ACPI for IRQ routing > hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 > hpet0: 3 comparators, 64-bit 14.318180 MHz counter > pnp: PnP ACPI init > ACPI: bus type pnp registered > pnp 00:07: io resource (0x1640-0x164f) overlaps 0000:00:1c.0 BAR 7 > (0x1000-0x1fff), disabling > pnp: PnP ACPI: found 9 devices > ACPI: ACPI bus type pnp unregistered > system 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved > system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved > system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved > system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved > system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved > system 00:01: iomem range 0xfed20000-0xfed8ffff has been reserved > system 00:05: iomem range 0xfed00000-0xfed003ff has been reserved > system 00:07: ioport range 0x680-0x6ef has been reserved > system 00:07: ioport range 0x800-0x80f has been reserved > system 00:07: ioport range 0x810-0x817 has been reserved > system 00:07: ioport range 0x400-0x47f has been reserved > system 00:07: ioport range 0x500-0x53f has been reserved > pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01 > pci 0000:00:1c.0: IO window: 0x1000-0x1fff > pci 0000:00:1c.0: MEM window: 0x90200000-0x902fffff > pci 0000:00:1c.0: PREFETCH window: 0x00000090500000-0x000000905fffff > pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02 > pci 0000:00:1c.1: IO window: disabled > pci 0000:00:1c.1: MEM window: 0x90100000-0x901fffff > pci 0000:00:1c.1: PREFETCH window: disabled > pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03 > pci 0000:00:1e.0: IO window: disabled > pci 0000:00:1e.0: MEM window: 0x90000000-0x900fffff > pci 0000:00:1e.0: PREFETCH window: disabled > pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > pci 0000:00:1c.0: setting latency timer to 64 > pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 > pci 0000:00:1c.1: setting latency timer to 64 > pci 0000:00:1e.0: power state changed by ACPI to D0 > pci 0000:00:1e.0: setting latency timer to 64 > pci_bus 0000:00: resource 0 io: [0x00-0xffff] > pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] > pci_bus 0000:01: resource 0 io: [0x1000-0x1fff] > pci_bus 0000:01: resource 1 mem: [0x90200000-0x902fffff] > pci_bus 0000:01: resource 2 mem: [0x90500000-0x905fffff] > pci_bus 0000:01: resource 3 mem: [0x0-0x0] > pci_bus 0000:02: resource 0 mem: [0x0-0x0] > pci_bus 0000:02: resource 1 mem: [0x90100000-0x901fffff] > pci_bus 0000:02: resource 2 mem: [0x0-0x0] > pci_bus 0000:02: resource 3 mem: [0x0-0x0] > pci_bus 0000:03: resource 0 mem: [0x0-0x0] > pci_bus 0000:03: resource 1 mem: [0x90000000-0x900fffff] > pci_bus 0000:03: resource 2 mem: [0x0-0x0] > pci_bus 0000:03: resource 3 io: [0x00-0xffff] > pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff] > NET: Registered protocol family 2 > IP route cache hash table entries: 65536 (order: 7, 524288 bytes) > TCP established hash table entries: 262144 (order: 10, 4194304 bytes) > TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) > TCP: Hash tables configured (established 262144 bind 65536) > TCP reno registered > NET: Registered protocol family 1 > checking if image is initramfs... it is > Freeing initrd memory: 1088k freed > Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba > HugeTLB registered 2 MB page size, pre-allocated 0 pages > Installing knfsd (copyright (C) 1996 okir@monad.swb.de). > msgmni has been set to 3953 > alg: No test for stdrng (krng) > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered (default) > pci 0000:00:02.0: Boot video device > ACPI: AC Adapter [ADP1] (on-line) > Switched to high resolution mode on CPU 1 > Switched to high resolution mode on CPU 0 > ACPI: Battery Slot [BAT0] (battery present) > input: Power Button (FF) as /class/input/input0 > ACPI: Power Button (FF) [PWRF] > input: Lid Switch as /class/input/input1 > ACPI: Lid Switch [LID0] > input: Power Button (CM) as /class/input/input2 > ACPI: Power Button (CM) [PWRB] > input: Sleep Button (CM) as /class/input/input3 > ACPI: Sleep Button (CM) [SLPB] > ACPI: SSDT 7EEB8C10, 02AE (r1 APPLE Cpu0Ist 3000 INTL 20050309) > ACPI: SSDT 7EEB8910, 02A0 (r1 APPLE Cpu0Cst 3001 INTL 20050309) > Monitor-Mwait will be used to enter C-1 state > Monitor-Mwait will be used to enter C-2 state > Monitor-Mwait will be used to enter C-3 state > ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) > processor ACPI_CPU:00: registered as cooling_device0 > ACPI: Processor [CPU0] (supports 8 throttling states) > ACPI: SSDT 7EEB8F10, 0087 (r1 APPLE Cpu1Ist 3000 INTL 20050309) > ACPI: SSDT 7EEB7F10, 0085 (r1 APPLE Cpu1Cst 3000 INTL 20050309) > ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) > processor ACPI_CPU:01: registered as cooling_device1 > ACPI: Processor [CPU1] (supports 8 throttling states) > Real Time Clock Driver v1.12b > intel_rng: FWH not detected > Linux agpgart interface v0.103 > agpgart-intel 0000:00:00.0: Intel 945GM Chipset > agpgart-intel 0000:00:00.0: detected 16124K stolen memory > agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000 > intelfb: Framebuffer driver for Intel(R) > 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/945GME/965G/965GM > chipsets > intelfb: Version 0.9.6 > intelfb 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > intelfb: 00:02.0: Intel(R) 945GM, aperture size 256MB, stolen memory 16124kB > intelfb: Non-CRT device is enabled ( LVDS port ). Disabling mode switching. > intelfb: Video mode must be programmed at boot time. > Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled > floppy0: no floppy controllers found > brd: module loaded > loop: module loaded > Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI > Copyright (c) 1999-2006 Intel Corporation. > e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI > e100: Copyright(c) 1999-2006 Intel Corporation > sky2 driver version 1.22 > sky2 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > sky2 0000:01:00.0: setting latency timer to 64 > sky2 0000:01:00.0: Yukon-2 EC chip revision 2 > sky2 0000:01:00.0: Marvell Yukon 88E8053 Gigabit Ethernet Controller > Part Number: Yukon 88E8053 > Engineering Level: Rev. 2.2 > Manufacturer: Marvell > sky2 0000:01:00.0: irq 24 for MSI/MSI-X > sky2 eth0: addr 00:19:e3:43:1c:a3 > console [netcon0] enabled > netconsole: network logging started > Linux video capture interface: v2.00 > usbcore: registered new interface driver uvcvideo > USB Video Class driver (v0.1.0) > Uniform Multi-Platform E-IDE driver > piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x02) > pci 0000:00:1f.1: power state changed by ACPI to D0 > pci 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 > piix 0000:00:1f.1: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0x20b0-0x20b7 > ide1: BM-DMA at 0x20b8-0x20bf > Probing IDE interface ide0... > hda: HL-DT-ST DVDRW GSA-S10N, ATAPI CD/DVD-ROM drive > hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 > hda: UDMA/33 mode selected > Probing IDE interface ide1... > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > ide1 at 0x170-0x177,0x376 on irq 15 > ide_generic: please use "probe_mask=0x3f" module parameter for probing > all legacy ISA IDE ports > ide-gd driver 1.18 > ide-cd driver 5.00 > ide-cd: hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache > Uniform CD-ROM driver Revision: 3.20 > 3ware Storage Controller device driver for Linux v1.26.02.002. > Driver 'sd' needs updating - please use bus_type methods > Driver 'sr' needs updating - please use bus_type methods > ata_piix 0000:00:1f.2: version 2.12 > ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 > ata_piix 0000:00:1f.2: MAP [ P0 P2 -- -- ] > ata_piix 0000:00:1f.2: setting latency timer to 64 > scsi0 : ata_piix > scsi1 : ata_piix > ata1: SATA max UDMA/133 cmd 0x20c8 ctl 0x20ec bmdma 0x20a0 irq 19 > ata2: SATA max UDMA/133 cmd 0x20c0 ctl 0x20e8 bmdma 0x20a8 irq 19 > ata1.01: ATA-7: ST9160821AS, 3.CAE, max UDMA/133 > ata1.01: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32) > ata1.01: configured for UDMA/133 > isa bounce pool size: 16 pages > scsi 0:0:1:0: Direct-Access ATA ST9160821AS 3.CA PQ: 0 ANSI: 5 > sd 0:0:1:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) > sd 0:0:1:0: [sda] Write Protect is off > sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00 > sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sd 0:0:1:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) > sd 0:0:1:0: [sda] Write Protect is off > sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00 > sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sda: sda1 sda2 sda3 sda4 > sd 0:0:1:0: [sda] Attached SCSI disk > sd 0:0:1:0: Attached scsi generic sg0 type 0 > Fusion MPT base driver 3.04.07 > Copyright (c) 1999-2008 LSI Corporation > Fusion MPT SPI Host driver 3.04.07 > ohci1394 0000:03:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 > ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[19] > MMIO=[90000000-900007ff] Max Packet=[2048] IR/IT contexts=[8/8] > ieee1394: raw1394: /dev/raw1394 device initialized > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 21 (level, low) -> IRQ 21 > ehci_hcd 0000:00:1d.7: setting latency timer to 64 > ehci_hcd 0000:00:1d.7: EHCI Host Controller > ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 > ehci_hcd 0000:00:1d.7: debug port 1 > ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported > ehci_hcd 0000:00:1d.7: irq 21, io mem 0x90445400 > ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 8 ports detected > ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver > uhci_hcd: USB Universal Host Controller Interface driver > uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 > uhci_hcd 0000:00:1d.0: setting latency timer to 64 > uhci_hcd 0000:00:1d.0: UHCI Host Controller > uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 > uhci_hcd 0000:00:1d.0: irq 21, io base 0x00002080 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 2 ports detected > uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 > uhci_hcd 0000:00:1d.1: setting latency timer to 64 > uhci_hcd 0000:00:1d.1: UHCI Host Controller > uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 > uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 > usb usb3: configuration #1 chosen from 1 choice > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 2 ports detected > uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 > uhci_hcd 0000:00:1d.2: setting latency timer to 64 > uhci_hcd 0000:00:1d.2: UHCI Host Controller > uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 > uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 > usb usb4: configuration #1 chosen from 1 choice > hub 4-0:1.0: USB hub found > hub 4-0:1.0: 2 ports detected > uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 > uhci_hcd 0000:00:1d.3: setting latency timer to 64 > uhci_hcd 0000:00:1d.3: UHCI Host Controller > uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 > uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002020 > usb usb5: configuration #1 chosen from 1 choice > hub 5-0:1.0: USB hub found > hub 5-0:1.0: 2 ports detected > usbcore: registered new interface driver usblp > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > PNP: No PS/2 controller found. Probing ports directly. > i8042.c: No controller found. > mice: PS/2 mouse device common for all mice > device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com > cpuidle: using governor ladder > cpuidle: using governor menu > Marking TSC unstable due to TSC halts in idle > usbcore: registered new interface driver usbhid > usbhid: v2.6:USB HID core driver > oprofile: using NMI interrupt. > Netfilter messages via NETLINK v0.30. > nf_conntrack version 0.5.0 (16384 buckets, 65536 max) > CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use > nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or > sysctl net.netfilter.nf_conntrack_acct=1 to enable it. > xt_time: kernel timezone is -0000 > ip_tables: (C) 2000-2006 Netfilter Core Team > arp_tables: (C) 2002 David S. Miller > TCP cubic registered > NET: Registered protocol family 10 > IPv6 over IPv4 tunneling driver > NET: Registered protocol family 17 > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > registered taskstats version 1 > Freeing unused kernel memory: 372k freed > usb 1-1: new high speed USB device using ehci_hcd and address 2 > usb 1-1: configuration #1 chosen from 1 choice > scsi2 : SCSI emulation for USB Mass Storage devices > usb-storage: device found at 2 > usb-storage: waiting for device to settle before scanning > usb 1-3: new high speed USB device using ehci_hcd and address 4 > usb 1-3: configuration #1 chosen from 1 choice > hub 1-3:1.0: USB hub found > hub 1-3:1.0: 2 ports detected > Clocksource tsc unstable (delta = -265511863 ns) > usb 1-4: new high speed USB device using ehci_hcd and address 5 > usb 1-4: configuration #1 chosen from 1 choice > ieee1394: Host added: ID:BUS[0-00:1023] GUID[001cb3fffe8ab416] > usb 2-2: new full speed USB device using uhci_hcd and address 2 > usb 2-2: configuration #1 chosen from 1 choice > input: Apple Computer Apple Internal Keyboard / Trackpad as /class/input/input4 > apple 0003:05AC:021A.0001: input: USB HID v1.11 Keyboard [Apple > Computer Apple Internal Keyboard / Trackpad] on > usb-0000:00:1d.0-2/input0 > input: Apple Computer Apple Internal Keyboard / Trackpad as /class/input/input5 > apple 0003:05AC:021A.0002: input: USB HID v1.11 Device [Apple Computer > Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2/input2 > usb 4-2: new full speed USB device using uhci_hcd and address 2 > usb 4-2: configuration #1 chosen from 1 choice > generic-usb 0003:05AC:8240.0003: claimed by neither input, hiddev nor hidraw > usb 5-1: new full speed USB device using uhci_hcd and address 2 > usb 5-1: configuration #1 chosen from 1 choice > input: HID 05ac:1000 as /class/input/input6 > generic-usb 0003:05AC:1000.0004: input: USB HID v1.11 Keyboard [HID > 05ac:1000] on usb-0000:00:1d.3-1/input0 > input: HID 05ac:1000 as /class/input/input7 > generic-usb 0003:05AC:1000.0005: input: USB HID v1.11 Mouse [HID > 05ac:1000] on usb-0000:00:1d.3-1/input1 > usb 1-3.1: new high speed USB device using ehci_hcd and address 8 > usb 1-3.1: configuration #1 chosen from 1 choice > hub 1-3.1:1.0: USB hub found > hub 1-3.1:1.0: 4 ports detected > usb 1-3.2: new low speed USB device using ehci_hcd and address 9 > usb 1-3.2: configuration #1 chosen from 1 choice > input: Logitech USB Mouse as /class/input/input8 > generic-usb 0003:046D:C00C.0006: input: USB HID v1.10 Mouse [Logitech > USB Mouse] on usb-0000:00:1d.7-3.2/input0 > usb 1-3.1.1: new high speed USB device using ehci_hcd and address 10 > usb 1-3.1.1: configuration #1 chosen from 1 choice > scsi3 : SCSI emulation for USB Mass Storage devices > usb-storage: device found at 10 > usb-storage: waiting for device to settle before scanning > usb 1-3.1.3: new high speed USB device using ehci_hcd and address 11 > usb 1-3.1.3: configuration #1 chosen from 1 choice > hub 1-3.1.3:1.0: USB hub found > hub 1-3.1.3:1.0: 3 ports detected > usb 1-3.1.4: new high speed USB device using ehci_hcd and address 12 > usb 1-3.1.4: configuration #1 chosen from 1 choice > scsi4 : SCSI emulation for USB Mass Storage devices > usb-storage: device found at 12 > usb-storage: waiting for device to settle before scanning > usb 1-3.1.3.1: new low speed USB device using ehci_hcd and address 13 > usb 1-3.1.3.1: configuration #1 chosen from 1 choice > input: No brand KVM as /class/input/input9 > generic-usb 0003:10D5:5552.0007: input: USB HID v1.10 Keyboard [No > brand KVM] on usb-0000:00:1d.7-3.1.3.1/input0 > input: No brand KVM as /class/input/input10 > generic-usb 0003:10D5:5552.0008: input: USB HID v1.10 Mouse [No brand > KVM] on usb-0000:00:1d.7-3.1.3.1/input1 > scsi 2:0:0:0: Direct-Access Ext Hard Disk PQ: 0 ANSI: 4 > sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) > sd 2:0:0:0: [sdb] Write Protect is off > sd 2:0:0:0: [sdb] Mode Sense: 10 00 00 00 > sd 2:0:0:0: [sdb] Assuming drive cache: write through > sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) > sd 2:0:0:0: [sdb] Write Protect is off > sd 2:0:0:0: [sdb] Mode Sense: 10 00 00 00 > sd 2:0:0:0: [sdb] Assuming drive cache: write through > sdb: sdb1 < sdb5 sdb6 > > sd 2:0:0:0: [sdb] Attached SCSI disk > sd 2:0:0:0: Attached scsi generic sg1 type 0 > usb-storage: device scan complete > kjournald starting. Commit interval 5 seconds > EXT3-fs: mounted filesystem with ordered data mode. > udev: renamed network interface eth0 to eth1 > scsi 3:0:0:0: Direct-Access Generic Flash HS-CF 4.44 PQ: 0 ANSI: 0 > sd 3:0:0:0: [sdc] Attached SCSI removable disk > sd 3:0:0:0: Attached scsi generic sg2 type 0 > usb-storage: device scan complete > applesmc: Apple MacBook (v2) detected: > applesmc: - Model with accelerometer > applesmc: - Model without light sensors and backlight > applesmc: - Model with 10 temperature sensors > applesmc: device has already been initialized (0xe0, 0xf8). > applesmc: device successfully initialized. > applesmc: 1 fans found. > input: applesmc as /class/input/input11 > applesmc: driver successfully loaded. > input: PC Speaker as /class/input/input12 > scsi 4:0:0:0: Direct-Access Maxtor 6 L200R0 BAH4 PQ: 0 ANSI: 0 > sd 4:0:0:0: [sdd] 398297087 512-byte hardware sectors: (203 GB/189 GiB) > sd 4:0:0:0: [sdd] Write Protect is off > sd 4:0:0:0: [sdd] Mode Sense: 03 00 00 00 > sd 4:0:0:0: [sdd] Assuming drive cache: write through > sd 4:0:0:0: [sdd] 398297087 512-byte hardware sectors: (203 GB/189 GiB) > sd 4:0:0:0: [sdd] Write Protect is off > sd 4:0:0:0: [sdd] Mode Sense: 03 00 00 00 > sd 4:0:0:0: [sdd] Assuming drive cache: write through > sdd: sdd1 > sd 4:0:0:0: [sdd] Attached SCSI disk > sd 4:0:0:0: Attached scsi generic sg3 type 0 > usb-storage: device scan complete > appletouch: Geyser mode initialized. > input: appletouch as /class/input/input13 > usbcore: registered new interface driver appletouch > HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 > HDA Intel 0000:00:1b.0: setting latency timer to 64 > hda_codec: STAC922x, Apple subsys_id=106b2200 > input: HDA Intel Line In at Ext Left Jack as /class/input/input14 > input: HDA Intel Mic at Ext Left Jack as /class/input/input15 > input: HDA Intel HP Out at Ext Left Jack as /class/input/input16 > EXT3 FS on dm-2, internal journal > fuse init (API version 7.11) > usbcore: registered new interface driver usbserial > USB Serial support registered for generic > usbcore: registered new interface driver usbserial_generic > usbserial: USB Serial Driver core > USB Serial support registered for pl2303 > usbcore: registered new interface driver pl2303 > pl2303: Prolific PL2303 USB to serial adaptor driver > EXT4-fs: barriers enabled > kjournald2 starting: pid 4443, dev dm-0:8, commit interval 5 seconds > EXT4 FS on dm-0, internal journal on dm-0:8 > EXT4-fs: delayed allocation enabled > EXT4-fs: mballoc enabled > EXT4-fs: mounted filesystem dm-0 with ordered data mode > EXT4-fs: barriers enabled > kjournald2 starting: pid 4444, dev dm-4:8, commit interval 5 seconds > EXT4 FS on dm-4, internal journal on dm-4:8 > EXT4-fs: delayed allocation enabled > EXT4-fs: mballoc enabled > EXT4-fs: mounted filesystem dm-4 with ordered data mode > EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended > Adding 1048568k swap on /dev/mapper/s-swap. Priority:-1 extents:1 > across:1048568k > sky2 eth1: enabling interface > ADDRCONF(NETDEV_UP): eth1: link is not ready > sky2 eth1: Link is up at 1000 Mbps, full duplex, flow control both > ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready > eth1: no IPv6 routers present > [drm] Initialized drm 1.1.0 20060810 > pci 0000:00:02.0: setting latency timer to 64 > [drm] Initialized i915 1.6.0 20080730 on minor 0 > JBD: barrier-based sync failed on dm-0:8 - disabling barriers > CE: hpet increasing min_delta_ns to 15000 nsec > ACPI: EC: GPE storm detected, transactions will use polling mode ^ permalink raw reply [flat|nested] 15+ messages in thread
[parent not found: <897274600903292015n44005d12l82b0fafd170d6292@mail.gmail.com>]
* Re: 2.6.29 on MacBook 2,1 fails to reboot [not found] ` <897274600903292015n44005d12l82b0fafd170d6292@mail.gmail.com> @ 2009-03-30 3:18 ` Trenton D. Adams 2009-03-30 4:03 ` Justin Mattock 2009-03-30 4:55 ` Trenton D. Adams 0 siblings, 2 replies; 15+ messages in thread From: Trenton D. Adams @ 2009-03-30 3:18 UTC (permalink / raw) To: Morten P.D. Stevens; +Cc: Linux Kernel Mailing List I recall it working on 2.6.28, but i didn't have vanilla sources installed. I used 2.6.28 gentoo sources. I'm just compiling 2.6.28 as we speak, as I figured you'd ask. I've marked 2.6.29 as bad with "git bisect". I'll let you know when I've narrowed it down for you. Can't wait to try "git bisect" *big smile*. On Sun, Mar 29, 2009 at 9:15 PM, Morten P.D. Stevens <mstevens@win-professional.com> wrote: > Hi, > > at first view your dmesg should be okay. > > does it reboot with 2.6.28 or lower? > > Morten > > 2009/3/30 Trenton Adams <trenton.d.adams@gmail.com> >> >> Oops, gmail doesn't reply to all by default. >> >> On Sun, Mar 29, 2009 at 8:46 PM, Morten P.D. Stevens >> <mstevens@win-professional.com> wrote: >> > Hi, >> > >> >> System information below. If you need more info, let me know. >> > >> > Please post your dmesg output. >> >> tdamac linux # dmesg >> Linux version 2.6.29 (root@tdamac) (gcc version 4.1.2 (Gentoo 4.1.2 >> p1.3)) #3 SMP Sun Mar 29 19:07:55 MDT 2009 >> Command line: root=/dev/ram0 init=/linuxrc real_root=/dev/s/sys dolvm >> KERNEL supported cpus: >> Intel GenuineIntel >> AMD AuthenticAMD >> Centaur CentaurHauls >> BIOS-provided physical RAM map: >> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) >> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) >> BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) >> BIOS-e820: 0000000000100000 - 000000007e08c000 (usable) >> BIOS-e820: 000000007e08c000 - 000000007e28d000 (ACPI NVS) >> BIOS-e820: 000000007e28d000 - 000000007eebe000 (ACPI data) >> BIOS-e820: 000000007eebe000 - 000000007eeef000 (ACPI NVS) >> BIOS-e820: 000000007eeef000 - 000000007ef00000 (ACPI data) >> BIOS-e820: 000000007ef00000 - 0000000080000000 (reserved) >> BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) >> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) >> BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) >> BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved) >> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) >> BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) >> DMI 2.4 present. >> last_pfn = 0x7e08c max_arch_pfn = 0x100000000 >> init_memory_mapping: 0000000000000000-000000007e08c000 >> 0000000000 - 007e000000 page 2M >> 007e000000 - 007e08c000 page 4k >> kernel direct mapping tables up to 7e08c000 @ 8000-c000 >> last_map_addr: 7e08c000 end: 7e08c000 >> RAMDISK: 37edf000 - 37fef088 >> ACPI: RSDP 000FE020, 0024 (r2 APPLE ) >> ACPI: XSDT 7EEFD1C0, 0074 (r1 APPLE Apple00 A5 1000013) >> ACPI: FACP 7EEFB000, 00F4 (r3 APPLE Apple00 A5 Loki 5F) >> FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) >> ACPI: DSDT 7EEF0000, 41E4 (r1 APPLE MacBook 20001 INTL 20050309) >> ACPI: FACS 7EEC0000, 0040 >> ACPI: HPET 7EEFA000, 0038 (r1 APPLE Apple00 1 Loki 5F) >> ACPI: APIC 7EEF9000, 0068 (r1 APPLE Apple00 1 Loki 5F) >> ACPI: MCFG 7EEF8000, 003C (r1 APPLE Apple00 1 Loki 5F) >> ACPI: ASF! 7EEF7000, 00A0 (r32 APPLE Apple00 1 Loki 5F) >> ACPI: SBST 7EEF6000, 0030 (r1 APPLE Apple00 1 Loki 5F) >> ACPI: ECDT 7EEF5000, 0053 (r1 APPLE Apple00 1 Loki 5F) >> ACPI: SSDT 7EEEF000, 04DC (r1 APPLE CpuPm 3000 INTL 20050309) >> ACPI: SSDT 7EEBD000, 064F (r1 SataRe SataPri 1000 INTL 20050309) >> ACPI: SSDT 7EEBC000, 069C (r1 SataRe SataSec 1000 INTL 20050309) >> ACPI: Local APIC address 0xfee00000 >> (6 early reservations) ==> bootmem [0000000000 - 007e08c000] >> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - >> 0000001000] >> #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - >> 0000008000] >> #2 [0000200000 - 0000a43b8c] TEXT DATA BSS ==> [0000200000 - >> 0000a43b8c] >> #3 [0037edf000 - 0037fef088] RAMDISK ==> [0037edf000 - >> 0037fef088] >> #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - >> 0000100000] >> #5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - >> 000000a000] >> [ffffe20000000000-ffffe20001bfffff] PMD -> >> [ffff880001200000-ffff880002dfffff] on node 0 >> Zone PFN ranges: >> DMA 0x00000000 -> 0x00001000 >> DMA32 0x00001000 -> 0x00100000 >> Normal 0x00100000 -> 0x00100000 >> Movable zone start PFN for each node >> early_node_map[2] active PFN ranges >> 0: 0x00000000 -> 0x0000009f >> 0: 0x00000100 -> 0x0007e08c >> On node 0 totalpages: 516139 >> DMA zone: 56 pages used for memmap >> DMA zone: 2216 pages reserved >> DMA zone: 1727 pages, LIFO batch:0 >> DMA32 zone: 7002 pages used for memmap >> DMA32 zone: 505138 pages, LIFO batch:31 >> ACPI: PM-Timer IO Port: 0x408 >> ACPI: Local APIC address 0xfee00000 >> ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) >> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) >> ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) >> ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) >> ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) >> IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23 >> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) >> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) >> ACPI: IRQ0 used by override. >> ACPI: IRQ2 used by override. >> ACPI: IRQ9 used by override. >> Using ACPI (MADT) for SMP configuration information >> ACPI: HPET id: 0x8086a201 base: 0xfed00000 >> SMP: Allowing 2 CPUs, 0 hotplug CPUs >> nr_irqs_gsi: 24 >> Allocating PCI resources starting at 88000000 (gap: 80000000:70000000) >> NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1 >> PERCPU: Allocating 53248 bytes of per cpu data >> Built 1 zonelists in Zone order, mobility grouping on. Total pages: >> 506865 >> Kernel command line: root=/dev/ram0 init=/linuxrc real_root=/dev/s/sys >> dolvm >> Initializing CPU#0 >> PID hash table entries: 4096 (order: 12, 32768 bytes) >> Extended CMOS year: 2000 >> Fast TSC calibration failed >> TSC: Unable to calibrate against PIT >> TSC: using PMTIMER reference calibration >> Detected 2161.212 MHz processor. >> Console: colour VGA+ 80x25 >> console [tty0] enabled >> Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) >> Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) >> Checking aperture... >> No AGP bridge found >> Memory: 2022216k/2064944k available (4392k kernel code, 388k absent, >> 41684k reserved, 2619k data, 372k init) >> SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 >> hpet clockevent registered >> HPET: 3 timers in total, 0 timers will be used for per-cpu timer >> Calibrating delay loop (skipped), value calculated using timer >> frequency.. 4322.42 BogoMIPS (lpj=8644848) >> Mount-cache hash table entries: 256 >> CPU: L1 I cache: 32K, L1 D cache: 32K >> CPU: L2 cache: 4096K >> [ds] using Core 2/Atom configuration >> CPU: Physical Processor ID: 0 >> CPU: Processor Core ID: 0 >> CPU0: Thermal monitoring enabled (TM2) >> using mwait in idle threads. >> ACPI: Core revision 20081204 >> Setting APIC routing to flat >> ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 >> CPU0: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping 06 >> Booting processor 1 APIC 0x1 ip 0x6000 >> Initializing CPU#1 >> Calibrating delay using timer specific routine.. 4322.44 BogoMIPS >> (lpj=8644898) >> CPU: L1 I cache: 32K, L1 D cache: 32K >> CPU: L2 cache: 4096K >> [ds] using Core 2/Atom configuration >> CPU: Physical Processor ID: 0 >> CPU: Processor Core ID: 1 >> CPU1: Thermal monitoring enabled (TM2) >> CPU1: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping 06 >> checking TSC synchronization [CPU#0 -> CPU#1]: passed. >> Brought up 2 CPUs >> Total of 2 processors activated (8644.87 BogoMIPS). >> net_namespace: 1784 bytes >> NET: Registered protocol family 16 >> ACPI: bus type pci registered >> PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 >> PCI: MCFG area at f0000000 reserved in E820 >> PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 >> PCI: Using MMCONFIG at f0000000 - f3ffffff >> PCI: Using configuration type 1 for base access >> bio: create slab <bio-0> at 0 >> ACPI: EC: EC description table is found, configuring boot EC >> ACPI: EC: non-query interrupt received, switching to interrupt mode >> ACPI: BIOS _OSI(Linux) query ignored >> ACPI: Interpreter enabled >> ACPI: (supports S0 S3 S5) >> ACPI: Using IOAPIC for interrupt routing >> ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62 >> ACPI: EC: driver started in interrupt mode >> ACPI: No dock devices found. >> ACPI: PCI Root Bridge [PCI0] (0000:00) >> pci 0000:00:02.0: reg 10 32bit mmio: [0x90380000-0x903fffff] >> pci 0000:00:02.0: reg 14 io port: [0x20e0-0x20e7] >> pci 0000:00:02.0: reg 18 32bit mmio: [0x80000000-0x8fffffff] >> pci 0000:00:02.0: reg 1c 32bit mmio: [0x90400000-0x9043ffff] >> pci 0000:00:02.1: reg 10 32bit mmio: [0x90300000-0x9037ffff] >> pci 0000:00:07.0: reg 10 32bit mmio: [0x90444000-0x90444fff] >> pci 0000:00:1b.0: reg 10 64bit mmio: [0x90440000-0x90443fff] >> pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold >> pci 0000:00:1b.0: PME# disabled >> pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold >> pci 0000:00:1c.0: PME# disabled >> pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold >> pci 0000:00:1c.1: PME# disabled >> pci 0000:00:1d.0: reg 20 io port: [0x2080-0x209f] >> pci 0000:00:1d.1: reg 20 io port: [0x2060-0x207f] >> pci 0000:00:1d.2: reg 20 io port: [0x2040-0x205f] >> pci 0000:00:1d.3: reg 20 io port: [0x2020-0x203f] >> pci 0000:00:1d.7: reg 10 32bit mmio: [0x90445400-0x904457ff] >> pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold >> pci 0000:00:1d.7: PME# disabled >> pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO >> pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO >> pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 000f) >> pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 1640 (mask 000f) >> pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 0300 (mask 001f) >> pci 0000:00:1f.1: reg 10 io port: [0x20d8-0x20df] >> pci 0000:00:1f.1: reg 14 io port: [0x20f4-0x20f7] >> pci 0000:00:1f.1: reg 18 io port: [0x20d0-0x20d7] >> pci 0000:00:1f.1: reg 1c io port: [0x20f0-0x20f3] >> pci 0000:00:1f.1: reg 20 io port: [0x20b0-0x20bf] >> pci 0000:00:1f.2: reg 10 io port: [0x20c8-0x20cf] >> pci 0000:00:1f.2: reg 14 io port: [0x20ec-0x20ef] >> pci 0000:00:1f.2: reg 18 io port: [0x20c0-0x20c7] >> pci 0000:00:1f.2: reg 1c io port: [0x20e8-0x20eb] >> pci 0000:00:1f.2: reg 20 io port: [0x20a0-0x20af] >> pci 0000:00:1f.2: reg 24 32bit mmio: [0x90445000-0x904453ff] >> pci 0000:00:1f.2: PME# supported from D3hot >> pci 0000:00:1f.2: PME# disabled >> pci 0000:00:1f.3: reg 20 io port: [0xefa0-0xefbf] >> pci 0000:01:00.0: reg 10 64bit mmio: [0x90200000-0x90203fff] >> pci 0000:01:00.0: reg 18 io port: [0x1000-0x10ff] >> pci 0000:01:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff] >> pci 0000:01:00.0: supports D1 D2 >> pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold >> pci 0000:01:00.0: PME# disabled >> pci 0000:00:1c.0: bridge io port: [0x1000-0x1fff] >> pci 0000:00:1c.0: bridge 32bit mmio: [0x90200000-0x902fffff] >> pci 0000:02:00.0: reg 10 64bit mmio: [0x90100000-0x9010ffff] >> pci 0000:02:00.0: supports D1 >> pci 0000:02:00.0: PME# supported from D0 D1 D3hot >> pci 0000:02:00.0: PME# disabled >> pci 0000:00:1c.1: bridge 32bit mmio: [0x90100000-0x901fffff] >> pci 0000:03:03.0: reg 10 32bit mmio: [0x90000000-0x90000fff] >> pci 0000:03:03.0: supports D1 D2 >> pci 0000:03:03.0: PME# supported from D0 D1 D2 D3hot >> pci 0000:03:03.0: PME# disabled >> pci 0000:00:1e.0: transparent bridge >> pci 0000:00:1e.0: bridge 32bit mmio: [0x90000000-0x900fffff] >> pci_bus 0000:00: on NUMA node 0 >> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] >> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] >> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] >> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] >> ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 >> ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15) >> ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 >> ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15) >> ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, >> disabled. >> ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, >> disabled. >> ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15) >> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15) >> SCSI subsystem initialized >> libata version 3.00 loaded. >> usbcore: registered new interface driver usbfs >> usbcore: registered new interface driver hub >> usbcore: registered new device driver usb >> PCI: Using ACPI for IRQ routing >> hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 >> hpet0: 3 comparators, 64-bit 14.318180 MHz counter >> pnp: PnP ACPI init >> ACPI: bus type pnp registered >> pnp 00:07: io resource (0x1640-0x164f) overlaps 0000:00:1c.0 BAR 7 >> (0x1000-0x1fff), disabling >> pnp: PnP ACPI: found 9 devices >> ACPI: ACPI bus type pnp unregistered >> system 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved >> system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved >> system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved >> system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved >> system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved >> system 00:01: iomem range 0xfed20000-0xfed8ffff has been reserved >> system 00:05: iomem range 0xfed00000-0xfed003ff has been reserved >> system 00:07: ioport range 0x680-0x6ef has been reserved >> system 00:07: ioport range 0x800-0x80f has been reserved >> system 00:07: ioport range 0x810-0x817 has been reserved >> system 00:07: ioport range 0x400-0x47f has been reserved >> system 00:07: ioport range 0x500-0x53f has been reserved >> pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01 >> pci 0000:00:1c.0: IO window: 0x1000-0x1fff >> pci 0000:00:1c.0: MEM window: 0x90200000-0x902fffff >> pci 0000:00:1c.0: PREFETCH window: 0x00000090500000-0x000000905fffff >> pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02 >> pci 0000:00:1c.1: IO window: disabled >> pci 0000:00:1c.1: MEM window: 0x90100000-0x901fffff >> pci 0000:00:1c.1: PREFETCH window: disabled >> pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03 >> pci 0000:00:1e.0: IO window: disabled >> pci 0000:00:1e.0: MEM window: 0x90000000-0x900fffff >> pci 0000:00:1e.0: PREFETCH window: disabled >> pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 >> pci 0000:00:1c.0: setting latency timer to 64 >> pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 >> pci 0000:00:1c.1: setting latency timer to 64 >> pci 0000:00:1e.0: power state changed by ACPI to D0 >> pci 0000:00:1e.0: setting latency timer to 64 >> pci_bus 0000:00: resource 0 io: [0x00-0xffff] >> pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] >> pci_bus 0000:01: resource 0 io: [0x1000-0x1fff] >> pci_bus 0000:01: resource 1 mem: [0x90200000-0x902fffff] >> pci_bus 0000:01: resource 2 mem: [0x90500000-0x905fffff] >> pci_bus 0000:01: resource 3 mem: [0x0-0x0] >> pci_bus 0000:02: resource 0 mem: [0x0-0x0] >> pci_bus 0000:02: resource 1 mem: [0x90100000-0x901fffff] >> pci_bus 0000:02: resource 2 mem: [0x0-0x0] >> pci_bus 0000:02: resource 3 mem: [0x0-0x0] >> pci_bus 0000:03: resource 0 mem: [0x0-0x0] >> pci_bus 0000:03: resource 1 mem: [0x90000000-0x900fffff] >> pci_bus 0000:03: resource 2 mem: [0x0-0x0] >> pci_bus 0000:03: resource 3 io: [0x00-0xffff] >> pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff] >> NET: Registered protocol family 2 >> IP route cache hash table entries: 65536 (order: 7, 524288 bytes) >> TCP established hash table entries: 262144 (order: 10, 4194304 bytes) >> TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) >> TCP: Hash tables configured (established 262144 bind 65536) >> TCP reno registered >> NET: Registered protocol family 1 >> checking if image is initramfs... it is >> Freeing initrd memory: 1088k freed >> Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba >> HugeTLB registered 2 MB page size, pre-allocated 0 pages >> Installing knfsd (copyright (C) 1996 okir@monad.swb.de). >> msgmni has been set to 3953 >> alg: No test for stdrng (krng) >> io scheduler noop registered >> io scheduler anticipatory registered >> io scheduler deadline registered >> io scheduler cfq registered (default) >> pci 0000:00:02.0: Boot video device >> ACPI: AC Adapter [ADP1] (on-line) >> Switched to high resolution mode on CPU 1 >> Switched to high resolution mode on CPU 0 >> ACPI: Battery Slot [BAT0] (battery present) >> input: Power Button (FF) as /class/input/input0 >> ACPI: Power Button (FF) [PWRF] >> input: Lid Switch as /class/input/input1 >> ACPI: Lid Switch [LID0] >> input: Power Button (CM) as /class/input/input2 >> ACPI: Power Button (CM) [PWRB] >> input: Sleep Button (CM) as /class/input/input3 >> ACPI: Sleep Button (CM) [SLPB] >> ACPI: SSDT 7EEB8C10, 02AE (r1 APPLE Cpu0Ist 3000 INTL 20050309) >> ACPI: SSDT 7EEB8910, 02A0 (r1 APPLE Cpu0Cst 3001 INTL 20050309) >> Monitor-Mwait will be used to enter C-1 state >> Monitor-Mwait will be used to enter C-2 state >> Monitor-Mwait will be used to enter C-3 state >> ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) >> processor ACPI_CPU:00: registered as cooling_device0 >> ACPI: Processor [CPU0] (supports 8 throttling states) >> ACPI: SSDT 7EEB8F10, 0087 (r1 APPLE Cpu1Ist 3000 INTL 20050309) >> ACPI: SSDT 7EEB7F10, 0085 (r1 APPLE Cpu1Cst 3000 INTL 20050309) >> ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) >> processor ACPI_CPU:01: registered as cooling_device1 >> ACPI: Processor [CPU1] (supports 8 throttling states) >> Real Time Clock Driver v1.12b >> intel_rng: FWH not detected >> Linux agpgart interface v0.103 >> agpgart-intel 0000:00:00.0: Intel 945GM Chipset >> agpgart-intel 0000:00:00.0: detected 16124K stolen memory >> agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000 >> intelfb: Framebuffer driver for Intel(R) >> 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/945GME/965G/965GM >> chipsets >> intelfb: Version 0.9.6 >> intelfb 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 >> intelfb: 00:02.0: Intel(R) 945GM, aperture size 256MB, stolen memory >> 16124kB >> intelfb: Non-CRT device is enabled ( LVDS port ). Disabling mode >> switching. >> intelfb: Video mode must be programmed at boot time. >> Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled >> floppy0: no floppy controllers found >> brd: module loaded >> loop: module loaded >> Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI >> Copyright (c) 1999-2006 Intel Corporation. >> e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI >> e100: Copyright(c) 1999-2006 Intel Corporation >> sky2 driver version 1.22 >> sky2 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 >> sky2 0000:01:00.0: setting latency timer to 64 >> sky2 0000:01:00.0: Yukon-2 EC chip revision 2 >> sky2 0000:01:00.0: Marvell Yukon 88E8053 Gigabit Ethernet Controller >> Part Number: Yukon 88E8053 >> Engineering Level: Rev. 2.2 >> Manufacturer: Marvell >> sky2 0000:01:00.0: irq 24 for MSI/MSI-X >> sky2 eth0: addr 00:19:e3:43:1c:a3 >> console [netcon0] enabled >> netconsole: network logging started >> Linux video capture interface: v2.00 >> usbcore: registered new interface driver uvcvideo >> USB Video Class driver (v0.1.0) >> Uniform Multi-Platform E-IDE driver >> piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x02) >> pci 0000:00:1f.1: power state changed by ACPI to D0 >> pci 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 >> piix 0000:00:1f.1: not 100% native mode: will probe irqs later >> ide0: BM-DMA at 0x20b0-0x20b7 >> ide1: BM-DMA at 0x20b8-0x20bf >> Probing IDE interface ide0... >> hda: HL-DT-ST DVDRW GSA-S10N, ATAPI CD/DVD-ROM drive >> hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 >> hda: UDMA/33 mode selected >> Probing IDE interface ide1... >> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 >> ide1 at 0x170-0x177,0x376 on irq 15 >> ide_generic: please use "probe_mask=0x3f" module parameter for probing >> all legacy ISA IDE ports >> ide-gd driver 1.18 >> ide-cd driver 5.00 >> ide-cd: hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache >> Uniform CD-ROM driver Revision: 3.20 >> 3ware Storage Controller device driver for Linux v1.26.02.002. >> Driver 'sd' needs updating - please use bus_type methods >> Driver 'sr' needs updating - please use bus_type methods >> ata_piix 0000:00:1f.2: version 2.12 >> ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 >> ata_piix 0000:00:1f.2: MAP [ P0 P2 -- -- ] >> ata_piix 0000:00:1f.2: setting latency timer to 64 >> scsi0 : ata_piix >> scsi1 : ata_piix >> ata1: SATA max UDMA/133 cmd 0x20c8 ctl 0x20ec bmdma 0x20a0 irq 19 >> ata2: SATA max UDMA/133 cmd 0x20c0 ctl 0x20e8 bmdma 0x20a8 irq 19 >> ata1.01: ATA-7: ST9160821AS, 3.CAE, max UDMA/133 >> ata1.01: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32) >> ata1.01: configured for UDMA/133 >> isa bounce pool size: 16 pages >> scsi 0:0:1:0: Direct-Access ATA ST9160821AS 3.CA PQ: 0 ANSI: >> 5 >> sd 0:0:1:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) >> sd 0:0:1:0: [sda] Write Protect is off >> sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00 >> sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't >> support DPO or FUA >> sd 0:0:1:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) >> sd 0:0:1:0: [sda] Write Protect is off >> sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00 >> sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't >> support DPO or FUA >> sda: sda1 sda2 sda3 sda4 >> sd 0:0:1:0: [sda] Attached SCSI disk >> sd 0:0:1:0: Attached scsi generic sg0 type 0 >> Fusion MPT base driver 3.04.07 >> Copyright (c) 1999-2008 LSI Corporation >> Fusion MPT SPI Host driver 3.04.07 >> ohci1394 0000:03:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 >> ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[19] >> MMIO=[90000000-900007ff] Max Packet=[2048] IR/IT contexts=[8/8] >> ieee1394: raw1394: /dev/raw1394 device initialized >> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver >> ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 21 (level, low) -> IRQ 21 >> ehci_hcd 0000:00:1d.7: setting latency timer to 64 >> ehci_hcd 0000:00:1d.7: EHCI Host Controller >> ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 >> ehci_hcd 0000:00:1d.7: debug port 1 >> ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported >> ehci_hcd 0000:00:1d.7: irq 21, io mem 0x90445400 >> ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 >> usb usb1: configuration #1 chosen from 1 choice >> hub 1-0:1.0: USB hub found >> hub 1-0:1.0: 8 ports detected >> ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver >> uhci_hcd: USB Universal Host Controller Interface driver >> uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 >> uhci_hcd 0000:00:1d.0: setting latency timer to 64 >> uhci_hcd 0000:00:1d.0: UHCI Host Controller >> uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 >> uhci_hcd 0000:00:1d.0: irq 21, io base 0x00002080 >> usb usb2: configuration #1 chosen from 1 choice >> hub 2-0:1.0: USB hub found >> hub 2-0:1.0: 2 ports detected >> uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 >> uhci_hcd 0000:00:1d.1: setting latency timer to 64 >> uhci_hcd 0000:00:1d.1: UHCI Host Controller >> uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 >> uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 >> usb usb3: configuration #1 chosen from 1 choice >> hub 3-0:1.0: USB hub found >> hub 3-0:1.0: 2 ports detected >> uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 >> uhci_hcd 0000:00:1d.2: setting latency timer to 64 >> uhci_hcd 0000:00:1d.2: UHCI Host Controller >> uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 >> uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 >> usb usb4: configuration #1 chosen from 1 choice >> hub 4-0:1.0: USB hub found >> hub 4-0:1.0: 2 ports detected >> uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 >> uhci_hcd 0000:00:1d.3: setting latency timer to 64 >> uhci_hcd 0000:00:1d.3: UHCI Host Controller >> uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 >> uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002020 >> usb usb5: configuration #1 chosen from 1 choice >> hub 5-0:1.0: USB hub found >> hub 5-0:1.0: 2 ports detected >> usbcore: registered new interface driver usblp >> Initializing USB Mass Storage driver... >> usbcore: registered new interface driver usb-storage >> USB Mass Storage support registered. >> PNP: No PS/2 controller found. Probing ports directly. >> i8042.c: No controller found. >> mice: PS/2 mouse device common for all mice >> device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: >> dm-devel@redhat.com >> cpuidle: using governor ladder >> cpuidle: using governor menu >> Marking TSC unstable due to TSC halts in idle >> usbcore: registered new interface driver usbhid >> usbhid: v2.6:USB HID core driver >> oprofile: using NMI interrupt. >> Netfilter messages via NETLINK v0.30. >> nf_conntrack version 0.5.0 (16384 buckets, 65536 max) >> CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use >> nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or >> sysctl net.netfilter.nf_conntrack_acct=1 to enable it. >> xt_time: kernel timezone is -0000 >> ip_tables: (C) 2000-2006 Netfilter Core Team >> arp_tables: (C) 2002 David S. Miller >> TCP cubic registered >> NET: Registered protocol family 10 >> IPv6 over IPv4 tunneling driver >> NET: Registered protocol family 17 >> RPC: Registered udp transport module. >> RPC: Registered tcp transport module. >> registered taskstats version 1 >> Freeing unused kernel memory: 372k freed >> usb 1-1: new high speed USB device using ehci_hcd and address 2 >> usb 1-1: configuration #1 chosen from 1 choice >> scsi2 : SCSI emulation for USB Mass Storage devices >> usb-storage: device found at 2 >> usb-storage: waiting for device to settle before scanning >> usb 1-3: new high speed USB device using ehci_hcd and address 4 >> usb 1-3: configuration #1 chosen from 1 choice >> hub 1-3:1.0: USB hub found >> hub 1-3:1.0: 2 ports detected >> Clocksource tsc unstable (delta = -265511863 ns) >> usb 1-4: new high speed USB device using ehci_hcd and address 5 >> usb 1-4: configuration #1 chosen from 1 choice >> ieee1394: Host added: ID:BUS[0-00:1023] GUID[001cb3fffe8ab416] >> usb 2-2: new full speed USB device using uhci_hcd and address 2 >> usb 2-2: configuration #1 chosen from 1 choice >> input: Apple Computer Apple Internal Keyboard / Trackpad as >> /class/input/input4 >> apple 0003:05AC:021A.0001: input: USB HID v1.11 Keyboard [Apple >> Computer Apple Internal Keyboard / Trackpad] on >> usb-0000:00:1d.0-2/input0 >> input: Apple Computer Apple Internal Keyboard / Trackpad as >> /class/input/input5 >> apple 0003:05AC:021A.0002: input: USB HID v1.11 Device [Apple Computer >> Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2/input2 >> usb 4-2: new full speed USB device using uhci_hcd and address 2 >> usb 4-2: configuration #1 chosen from 1 choice >> generic-usb 0003:05AC:8240.0003: claimed by neither input, hiddev nor >> hidraw >> usb 5-1: new full speed USB device using uhci_hcd and address 2 >> usb 5-1: configuration #1 chosen from 1 choice >> input: HID 05ac:1000 as /class/input/input6 >> generic-usb 0003:05AC:1000.0004: input: USB HID v1.11 Keyboard [HID >> 05ac:1000] on usb-0000:00:1d.3-1/input0 >> input: HID 05ac:1000 as /class/input/input7 >> generic-usb 0003:05AC:1000.0005: input: USB HID v1.11 Mouse [HID >> 05ac:1000] on usb-0000:00:1d.3-1/input1 >> usb 1-3.1: new high speed USB device using ehci_hcd and address 8 >> usb 1-3.1: configuration #1 chosen from 1 choice >> hub 1-3.1:1.0: USB hub found >> hub 1-3.1:1.0: 4 ports detected >> usb 1-3.2: new low speed USB device using ehci_hcd and address 9 >> usb 1-3.2: configuration #1 chosen from 1 choice >> input: Logitech USB Mouse as /class/input/input8 >> generic-usb 0003:046D:C00C.0006: input: USB HID v1.10 Mouse [Logitech >> USB Mouse] on usb-0000:00:1d.7-3.2/input0 >> usb 1-3.1.1: new high speed USB device using ehci_hcd and address 10 >> usb 1-3.1.1: configuration #1 chosen from 1 choice >> scsi3 : SCSI emulation for USB Mass Storage devices >> usb-storage: device found at 10 >> usb-storage: waiting for device to settle before scanning >> usb 1-3.1.3: new high speed USB device using ehci_hcd and address 11 >> usb 1-3.1.3: configuration #1 chosen from 1 choice >> hub 1-3.1.3:1.0: USB hub found >> hub 1-3.1.3:1.0: 3 ports detected >> usb 1-3.1.4: new high speed USB device using ehci_hcd and address 12 >> usb 1-3.1.4: configuration #1 chosen from 1 choice >> scsi4 : SCSI emulation for USB Mass Storage devices >> usb-storage: device found at 12 >> usb-storage: waiting for device to settle before scanning >> usb 1-3.1.3.1: new low speed USB device using ehci_hcd and address 13 >> usb 1-3.1.3.1: configuration #1 chosen from 1 choice >> input: No brand KVM as /class/input/input9 >> generic-usb 0003:10D5:5552.0007: input: USB HID v1.10 Keyboard [No >> brand KVM] on usb-0000:00:1d.7-3.1.3.1/input0 >> input: No brand KVM as /class/input/input10 >> generic-usb 0003:10D5:5552.0008: input: USB HID v1.10 Mouse [No brand >> KVM] on usb-0000:00:1d.7-3.1.3.1/input1 >> scsi 2:0:0:0: Direct-Access Ext Hard Disk PQ: 0 ANSI: >> 4 >> sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) >> sd 2:0:0:0: [sdb] Write Protect is off >> sd 2:0:0:0: [sdb] Mode Sense: 10 00 00 00 >> sd 2:0:0:0: [sdb] Assuming drive cache: write through >> sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) >> sd 2:0:0:0: [sdb] Write Protect is off >> sd 2:0:0:0: [sdb] Mode Sense: 10 00 00 00 >> sd 2:0:0:0: [sdb] Assuming drive cache: write through >> sdb: sdb1 < sdb5 sdb6 > >> sd 2:0:0:0: [sdb] Attached SCSI disk >> sd 2:0:0:0: Attached scsi generic sg1 type 0 >> usb-storage: device scan complete >> kjournald starting. Commit interval 5 seconds >> EXT3-fs: mounted filesystem with ordered data mode. >> udev: renamed network interface eth0 to eth1 >> scsi 3:0:0:0: Direct-Access Generic Flash HS-CF 4.44 PQ: 0 ANSI: >> 0 >> sd 3:0:0:0: [sdc] Attached SCSI removable disk >> sd 3:0:0:0: Attached scsi generic sg2 type 0 >> usb-storage: device scan complete >> applesmc: Apple MacBook (v2) detected: >> applesmc: - Model with accelerometer >> applesmc: - Model without light sensors and backlight >> applesmc: - Model with 10 temperature sensors >> applesmc: device has already been initialized (0xe0, 0xf8). >> applesmc: device successfully initialized. >> applesmc: 1 fans found. >> input: applesmc as /class/input/input11 >> applesmc: driver successfully loaded. >> input: PC Speaker as /class/input/input12 >> scsi 4:0:0:0: Direct-Access Maxtor 6 L200R0 BAH4 PQ: 0 ANSI: >> 0 >> sd 4:0:0:0: [sdd] 398297087 512-byte hardware sectors: (203 GB/189 GiB) >> sd 4:0:0:0: [sdd] Write Protect is off >> sd 4:0:0:0: [sdd] Mode Sense: 03 00 00 00 >> sd 4:0:0:0: [sdd] Assuming drive cache: write through >> sd 4:0:0:0: [sdd] 398297087 512-byte hardware sectors: (203 GB/189 GiB) >> sd 4:0:0:0: [sdd] Write Protect is off >> sd 4:0:0:0: [sdd] Mode Sense: 03 00 00 00 >> sd 4:0:0:0: [sdd] Assuming drive cache: write through >> sdd: sdd1 >> sd 4:0:0:0: [sdd] Attached SCSI disk >> sd 4:0:0:0: Attached scsi generic sg3 type 0 >> usb-storage: device scan complete >> appletouch: Geyser mode initialized. >> input: appletouch as /class/input/input13 >> usbcore: registered new interface driver appletouch >> HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 >> HDA Intel 0000:00:1b.0: setting latency timer to 64 >> hda_codec: STAC922x, Apple subsys_id=106b2200 >> input: HDA Intel Line In at Ext Left Jack as /class/input/input14 >> input: HDA Intel Mic at Ext Left Jack as /class/input/input15 >> input: HDA Intel HP Out at Ext Left Jack as /class/input/input16 >> EXT3 FS on dm-2, internal journal >> fuse init (API version 7.11) >> usbcore: registered new interface driver usbserial >> USB Serial support registered for generic >> usbcore: registered new interface driver usbserial_generic >> usbserial: USB Serial Driver core >> USB Serial support registered for pl2303 >> usbcore: registered new interface driver pl2303 >> pl2303: Prolific PL2303 USB to serial adaptor driver >> EXT4-fs: barriers enabled >> kjournald2 starting: pid 4443, dev dm-0:8, commit interval 5 seconds >> EXT4 FS on dm-0, internal journal on dm-0:8 >> EXT4-fs: delayed allocation enabled >> EXT4-fs: mballoc enabled >> EXT4-fs: mounted filesystem dm-0 with ordered data mode >> EXT4-fs: barriers enabled >> kjournald2 starting: pid 4444, dev dm-4:8, commit interval 5 seconds >> EXT4 FS on dm-4, internal journal on dm-4:8 >> EXT4-fs: delayed allocation enabled >> EXT4-fs: mballoc enabled >> EXT4-fs: mounted filesystem dm-4 with ordered data mode >> EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended >> Adding 1048568k swap on /dev/mapper/s-swap. Priority:-1 extents:1 >> across:1048568k >> sky2 eth1: enabling interface >> ADDRCONF(NETDEV_UP): eth1: link is not ready >> sky2 eth1: Link is up at 1000 Mbps, full duplex, flow control both >> ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready >> eth1: no IPv6 routers present >> [drm] Initialized drm 1.1.0 20060810 >> pci 0000:00:02.0: setting latency timer to 64 >> [drm] Initialized i915 1.6.0 20080730 on minor 0 >> JBD: barrier-based sync failed on dm-0:8 - disabling barriers >> CE: hpet increasing min_delta_ns to 15000 nsec >> ACPI: EC: GPE storm detected, transactions will use polling mode > > ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-03-30 3:18 ` Trenton D. Adams @ 2009-03-30 4:03 ` Justin Mattock 2009-03-30 4:55 ` Trenton D. Adams 1 sibling, 0 replies; 15+ messages in thread From: Justin Mattock @ 2009-03-30 4:03 UTC (permalink / raw) To: Trenton D. Adams; +Cc: Morten P.D. Stevens, Linux Kernel Mailing List On Sun, Mar 29, 2009 at 8:18 PM, Trenton D. Adams <trenton.d.adams@gmail.com> wrote: > I recall it working on 2.6.28, but i didn't have vanilla sources > installed. I used 2.6.28 gentoo sources. I'm just compiling 2.6.28 > as we speak, as I figured you'd ask. I've marked 2.6.29 as bad with > "git bisect". I'll let you know when I've narrowed it down for you. > Can't wait to try "git bisect" *big smile*. > > On Sun, Mar 29, 2009 at 9:15 PM, Morten P.D. Stevens > <mstevens@win-professional.com> wrote: >> Hi, >> >> at first view your dmesg should be okay. >> >> does it reboot with 2.6.28 or lower? >> >> Morten >> >> 2009/3/30 Trenton Adams <trenton.d.adams@gmail.com> >>> >>> Oops, gmail doesn't reply to all by default. >>> >>> On Sun, Mar 29, 2009 at 8:46 PM, Morten P.D. Stevens >>> <mstevens@win-professional.com> wrote: >>> > Hi, >>> > >>> >> System information below. If you need more info, let me know. >>> > >>> > Please post your dmesg output. >>> >>> tdamac linux # dmesg >>> Linux version 2.6.29 (root@tdamac) (gcc version 4.1.2 (Gentoo 4.1.2 >>> p1.3)) #3 SMP Sun Mar 29 19:07:55 MDT 2009 >>> Command line: root=/dev/ram0 init=/linuxrc real_root=/dev/s/sys dolvm >>> KERNEL supported cpus: >>> Intel GenuineIntel >>> AMD AuthenticAMD >>> Centaur CentaurHauls >>> BIOS-provided physical RAM map: >>> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) >>> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) >>> BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) >>> BIOS-e820: 0000000000100000 - 000000007e08c000 (usable) >>> BIOS-e820: 000000007e08c000 - 000000007e28d000 (ACPI NVS) >>> BIOS-e820: 000000007e28d000 - 000000007eebe000 (ACPI data) >>> BIOS-e820: 000000007eebe000 - 000000007eeef000 (ACPI NVS) >>> BIOS-e820: 000000007eeef000 - 000000007ef00000 (ACPI data) >>> BIOS-e820: 000000007ef00000 - 0000000080000000 (reserved) >>> BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) >>> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) >>> BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) >>> BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved) >>> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) >>> BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) >>> DMI 2.4 present. >>> last_pfn = 0x7e08c max_arch_pfn = 0x100000000 >>> init_memory_mapping: 0000000000000000-000000007e08c000 >>> 0000000000 - 007e000000 page 2M >>> 007e000000 - 007e08c000 page 4k >>> kernel direct mapping tables up to 7e08c000 @ 8000-c000 >>> last_map_addr: 7e08c000 end: 7e08c000 >>> RAMDISK: 37edf000 - 37fef088 >>> ACPI: RSDP 000FE020, 0024 (r2 APPLE ) >>> ACPI: XSDT 7EEFD1C0, 0074 (r1 APPLE Apple00 A5 1000013) >>> ACPI: FACP 7EEFB000, 00F4 (r3 APPLE Apple00 A5 Loki 5F) >>> FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) >>> ACPI: DSDT 7EEF0000, 41E4 (r1 APPLE MacBook 20001 INTL 20050309) >>> ACPI: FACS 7EEC0000, 0040 >>> ACPI: HPET 7EEFA000, 0038 (r1 APPLE Apple00 1 Loki 5F) >>> ACPI: APIC 7EEF9000, 0068 (r1 APPLE Apple00 1 Loki 5F) >>> ACPI: MCFG 7EEF8000, 003C (r1 APPLE Apple00 1 Loki 5F) >>> ACPI: ASF! 7EEF7000, 00A0 (r32 APPLE Apple00 1 Loki 5F) >>> ACPI: SBST 7EEF6000, 0030 (r1 APPLE Apple00 1 Loki 5F) >>> ACPI: ECDT 7EEF5000, 0053 (r1 APPLE Apple00 1 Loki 5F) >>> ACPI: SSDT 7EEEF000, 04DC (r1 APPLE CpuPm 3000 INTL 20050309) >>> ACPI: SSDT 7EEBD000, 064F (r1 SataRe SataPri 1000 INTL 20050309) >>> ACPI: SSDT 7EEBC000, 069C (r1 SataRe SataSec 1000 INTL 20050309) >>> ACPI: Local APIC address 0xfee00000 >>> (6 early reservations) ==> bootmem [0000000000 - 007e08c000] >>> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - >>> 0000001000] >>> #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - >>> 0000008000] >>> #2 [0000200000 - 0000a43b8c] TEXT DATA BSS ==> [0000200000 - >>> 0000a43b8c] >>> #3 [0037edf000 - 0037fef088] RAMDISK ==> [0037edf000 - >>> 0037fef088] >>> #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - >>> 0000100000] >>> #5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - >>> 000000a000] >>> [ffffe20000000000-ffffe20001bfffff] PMD -> >>> [ffff880001200000-ffff880002dfffff] on node 0 >>> Zone PFN ranges: >>> DMA 0x00000000 -> 0x00001000 >>> DMA32 0x00001000 -> 0x00100000 >>> Normal 0x00100000 -> 0x00100000 >>> Movable zone start PFN for each node >>> early_node_map[2] active PFN ranges >>> 0: 0x00000000 -> 0x0000009f >>> 0: 0x00000100 -> 0x0007e08c >>> On node 0 totalpages: 516139 >>> DMA zone: 56 pages used for memmap >>> DMA zone: 2216 pages reserved >>> DMA zone: 1727 pages, LIFO batch:0 >>> DMA32 zone: 7002 pages used for memmap >>> DMA32 zone: 505138 pages, LIFO batch:31 >>> ACPI: PM-Timer IO Port: 0x408 >>> ACPI: Local APIC address 0xfee00000 >>> ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) >>> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) >>> ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) >>> ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) >>> ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) >>> IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23 >>> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) >>> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) >>> ACPI: IRQ0 used by override. >>> ACPI: IRQ2 used by override. >>> ACPI: IRQ9 used by override. >>> Using ACPI (MADT) for SMP configuration information >>> ACPI: HPET id: 0x8086a201 base: 0xfed00000 >>> SMP: Allowing 2 CPUs, 0 hotplug CPUs >>> nr_irqs_gsi: 24 >>> Allocating PCI resources starting at 88000000 (gap: 80000000:70000000) >>> NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1 >>> PERCPU: Allocating 53248 bytes of per cpu data >>> Built 1 zonelists in Zone order, mobility grouping on. Total pages: >>> 506865 >>> Kernel command line: root=/dev/ram0 init=/linuxrc real_root=/dev/s/sys >>> dolvm >>> Initializing CPU#0 >>> PID hash table entries: 4096 (order: 12, 32768 bytes) >>> Extended CMOS year: 2000 >>> Fast TSC calibration failed >>> TSC: Unable to calibrate against PIT >>> TSC: using PMTIMER reference calibration >>> Detected 2161.212 MHz processor. >>> Console: colour VGA+ 80x25 >>> console [tty0] enabled >>> Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) >>> Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) >>> Checking aperture... >>> No AGP bridge found >>> Memory: 2022216k/2064944k available (4392k kernel code, 388k absent, >>> 41684k reserved, 2619k data, 372k init) >>> SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 >>> hpet clockevent registered >>> HPET: 3 timers in total, 0 timers will be used for per-cpu timer >>> Calibrating delay loop (skipped), value calculated using timer >>> frequency.. 4322.42 BogoMIPS (lpj=8644848) >>> Mount-cache hash table entries: 256 >>> CPU: L1 I cache: 32K, L1 D cache: 32K >>> CPU: L2 cache: 4096K >>> [ds] using Core 2/Atom configuration >>> CPU: Physical Processor ID: 0 >>> CPU: Processor Core ID: 0 >>> CPU0: Thermal monitoring enabled (TM2) >>> using mwait in idle threads. >>> ACPI: Core revision 20081204 >>> Setting APIC routing to flat >>> ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 >>> CPU0: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping 06 >>> Booting processor 1 APIC 0x1 ip 0x6000 >>> Initializing CPU#1 >>> Calibrating delay using timer specific routine.. 4322.44 BogoMIPS >>> (lpj=8644898) >>> CPU: L1 I cache: 32K, L1 D cache: 32K >>> CPU: L2 cache: 4096K >>> [ds] using Core 2/Atom configuration >>> CPU: Physical Processor ID: 0 >>> CPU: Processor Core ID: 1 >>> CPU1: Thermal monitoring enabled (TM2) >>> CPU1: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping 06 >>> checking TSC synchronization [CPU#0 -> CPU#1]: passed. >>> Brought up 2 CPUs >>> Total of 2 processors activated (8644.87 BogoMIPS). >>> net_namespace: 1784 bytes >>> NET: Registered protocol family 16 >>> ACPI: bus type pci registered >>> PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 >>> PCI: MCFG area at f0000000 reserved in E820 >>> PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 >>> PCI: Using MMCONFIG at f0000000 - f3ffffff >>> PCI: Using configuration type 1 for base access >>> bio: create slab <bio-0> at 0 >>> ACPI: EC: EC description table is found, configuring boot EC >>> ACPI: EC: non-query interrupt received, switching to interrupt mode >>> ACPI: BIOS _OSI(Linux) query ignored >>> ACPI: Interpreter enabled >>> ACPI: (supports S0 S3 S5) >>> ACPI: Using IOAPIC for interrupt routing >>> ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62 >>> ACPI: EC: driver started in interrupt mode >>> ACPI: No dock devices found. >>> ACPI: PCI Root Bridge [PCI0] (0000:00) >>> pci 0000:00:02.0: reg 10 32bit mmio: [0x90380000-0x903fffff] >>> pci 0000:00:02.0: reg 14 io port: [0x20e0-0x20e7] >>> pci 0000:00:02.0: reg 18 32bit mmio: [0x80000000-0x8fffffff] >>> pci 0000:00:02.0: reg 1c 32bit mmio: [0x90400000-0x9043ffff] >>> pci 0000:00:02.1: reg 10 32bit mmio: [0x90300000-0x9037ffff] >>> pci 0000:00:07.0: reg 10 32bit mmio: [0x90444000-0x90444fff] >>> pci 0000:00:1b.0: reg 10 64bit mmio: [0x90440000-0x90443fff] >>> pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold >>> pci 0000:00:1b.0: PME# disabled >>> pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold >>> pci 0000:00:1c.0: PME# disabled >>> pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold >>> pci 0000:00:1c.1: PME# disabled >>> pci 0000:00:1d.0: reg 20 io port: [0x2080-0x209f] >>> pci 0000:00:1d.1: reg 20 io port: [0x2060-0x207f] >>> pci 0000:00:1d.2: reg 20 io port: [0x2040-0x205f] >>> pci 0000:00:1d.3: reg 20 io port: [0x2020-0x203f] >>> pci 0000:00:1d.7: reg 10 32bit mmio: [0x90445400-0x904457ff] >>> pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold >>> pci 0000:00:1d.7: PME# disabled >>> pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO >>> pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO >>> pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 000f) >>> pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 1640 (mask 000f) >>> pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 0300 (mask 001f) >>> pci 0000:00:1f.1: reg 10 io port: [0x20d8-0x20df] >>> pci 0000:00:1f.1: reg 14 io port: [0x20f4-0x20f7] >>> pci 0000:00:1f.1: reg 18 io port: [0x20d0-0x20d7] >>> pci 0000:00:1f.1: reg 1c io port: [0x20f0-0x20f3] >>> pci 0000:00:1f.1: reg 20 io port: [0x20b0-0x20bf] >>> pci 0000:00:1f.2: reg 10 io port: [0x20c8-0x20cf] >>> pci 0000:00:1f.2: reg 14 io port: [0x20ec-0x20ef] >>> pci 0000:00:1f.2: reg 18 io port: [0x20c0-0x20c7] >>> pci 0000:00:1f.2: reg 1c io port: [0x20e8-0x20eb] >>> pci 0000:00:1f.2: reg 20 io port: [0x20a0-0x20af] >>> pci 0000:00:1f.2: reg 24 32bit mmio: [0x90445000-0x904453ff] >>> pci 0000:00:1f.2: PME# supported from D3hot >>> pci 0000:00:1f.2: PME# disabled >>> pci 0000:00:1f.3: reg 20 io port: [0xefa0-0xefbf] >>> pci 0000:01:00.0: reg 10 64bit mmio: [0x90200000-0x90203fff] >>> pci 0000:01:00.0: reg 18 io port: [0x1000-0x10ff] >>> pci 0000:01:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff] >>> pci 0000:01:00.0: supports D1 D2 >>> pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold >>> pci 0000:01:00.0: PME# disabled >>> pci 0000:00:1c.0: bridge io port: [0x1000-0x1fff] >>> pci 0000:00:1c.0: bridge 32bit mmio: [0x90200000-0x902fffff] >>> pci 0000:02:00.0: reg 10 64bit mmio: [0x90100000-0x9010ffff] >>> pci 0000:02:00.0: supports D1 >>> pci 0000:02:00.0: PME# supported from D0 D1 D3hot >>> pci 0000:02:00.0: PME# disabled >>> pci 0000:00:1c.1: bridge 32bit mmio: [0x90100000-0x901fffff] >>> pci 0000:03:03.0: reg 10 32bit mmio: [0x90000000-0x90000fff] >>> pci 0000:03:03.0: supports D1 D2 >>> pci 0000:03:03.0: PME# supported from D0 D1 D2 D3hot >>> pci 0000:03:03.0: PME# disabled >>> pci 0000:00:1e.0: transparent bridge >>> pci 0000:00:1e.0: bridge 32bit mmio: [0x90000000-0x900fffff] >>> pci_bus 0000:00: on NUMA node 0 >>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] >>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] >>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] >>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] >>> ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 >>> ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15) >>> ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 >>> ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15) >>> ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, >>> disabled. >>> ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, >>> disabled. >>> ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15) >>> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15) >>> SCSI subsystem initialized >>> libata version 3.00 loaded. >>> usbcore: registered new interface driver usbfs >>> usbcore: registered new interface driver hub >>> usbcore: registered new device driver usb >>> PCI: Using ACPI for IRQ routing >>> hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 >>> hpet0: 3 comparators, 64-bit 14.318180 MHz counter >>> pnp: PnP ACPI init >>> ACPI: bus type pnp registered >>> pnp 00:07: io resource (0x1640-0x164f) overlaps 0000:00:1c.0 BAR 7 >>> (0x1000-0x1fff), disabling >>> pnp: PnP ACPI: found 9 devices >>> ACPI: ACPI bus type pnp unregistered >>> system 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved >>> system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved >>> system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved >>> system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved >>> system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved >>> system 00:01: iomem range 0xfed20000-0xfed8ffff has been reserved >>> system 00:05: iomem range 0xfed00000-0xfed003ff has been reserved >>> system 00:07: ioport range 0x680-0x6ef has been reserved >>> system 00:07: ioport range 0x800-0x80f has been reserved >>> system 00:07: ioport range 0x810-0x817 has been reserved >>> system 00:07: ioport range 0x400-0x47f has been reserved >>> system 00:07: ioport range 0x500-0x53f has been reserved >>> pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01 >>> pci 0000:00:1c.0: IO window: 0x1000-0x1fff >>> pci 0000:00:1c.0: MEM window: 0x90200000-0x902fffff >>> pci 0000:00:1c.0: PREFETCH window: 0x00000090500000-0x000000905fffff >>> pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02 >>> pci 0000:00:1c.1: IO window: disabled >>> pci 0000:00:1c.1: MEM window: 0x90100000-0x901fffff >>> pci 0000:00:1c.1: PREFETCH window: disabled >>> pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03 >>> pci 0000:00:1e.0: IO window: disabled >>> pci 0000:00:1e.0: MEM window: 0x90000000-0x900fffff >>> pci 0000:00:1e.0: PREFETCH window: disabled >>> pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 >>> pci 0000:00:1c.0: setting latency timer to 64 >>> pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 >>> pci 0000:00:1c.1: setting latency timer to 64 >>> pci 0000:00:1e.0: power state changed by ACPI to D0 >>> pci 0000:00:1e.0: setting latency timer to 64 >>> pci_bus 0000:00: resource 0 io: [0x00-0xffff] >>> pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] >>> pci_bus 0000:01: resource 0 io: [0x1000-0x1fff] >>> pci_bus 0000:01: resource 1 mem: [0x90200000-0x902fffff] >>> pci_bus 0000:01: resource 2 mem: [0x90500000-0x905fffff] >>> pci_bus 0000:01: resource 3 mem: [0x0-0x0] >>> pci_bus 0000:02: resource 0 mem: [0x0-0x0] >>> pci_bus 0000:02: resource 1 mem: [0x90100000-0x901fffff] >>> pci_bus 0000:02: resource 2 mem: [0x0-0x0] >>> pci_bus 0000:02: resource 3 mem: [0x0-0x0] >>> pci_bus 0000:03: resource 0 mem: [0x0-0x0] >>> pci_bus 0000:03: resource 1 mem: [0x90000000-0x900fffff] >>> pci_bus 0000:03: resource 2 mem: [0x0-0x0] >>> pci_bus 0000:03: resource 3 io: [0x00-0xffff] >>> pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff] >>> NET: Registered protocol family 2 >>> IP route cache hash table entries: 65536 (order: 7, 524288 bytes) >>> TCP established hash table entries: 262144 (order: 10, 4194304 bytes) >>> TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) >>> TCP: Hash tables configured (established 262144 bind 65536) >>> TCP reno registered >>> NET: Registered protocol family 1 >>> checking if image is initramfs... it is >>> Freeing initrd memory: 1088k freed >>> Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba >>> HugeTLB registered 2 MB page size, pre-allocated 0 pages >>> Installing knfsd (copyright (C) 1996 okir@monad.swb.de). >>> msgmni has been set to 3953 >>> alg: No test for stdrng (krng) >>> io scheduler noop registered >>> io scheduler anticipatory registered >>> io scheduler deadline registered >>> io scheduler cfq registered (default) >>> pci 0000:00:02.0: Boot video device >>> ACPI: AC Adapter [ADP1] (on-line) >>> Switched to high resolution mode on CPU 1 >>> Switched to high resolution mode on CPU 0 >>> ACPI: Battery Slot [BAT0] (battery present) >>> input: Power Button (FF) as /class/input/input0 >>> ACPI: Power Button (FF) [PWRF] >>> input: Lid Switch as /class/input/input1 >>> ACPI: Lid Switch [LID0] >>> input: Power Button (CM) as /class/input/input2 >>> ACPI: Power Button (CM) [PWRB] >>> input: Sleep Button (CM) as /class/input/input3 >>> ACPI: Sleep Button (CM) [SLPB] >>> ACPI: SSDT 7EEB8C10, 02AE (r1 APPLE Cpu0Ist 3000 INTL 20050309) >>> ACPI: SSDT 7EEB8910, 02A0 (r1 APPLE Cpu0Cst 3001 INTL 20050309) >>> Monitor-Mwait will be used to enter C-1 state >>> Monitor-Mwait will be used to enter C-2 state >>> Monitor-Mwait will be used to enter C-3 state >>> ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) >>> processor ACPI_CPU:00: registered as cooling_device0 >>> ACPI: Processor [CPU0] (supports 8 throttling states) >>> ACPI: SSDT 7EEB8F10, 0087 (r1 APPLE Cpu1Ist 3000 INTL 20050309) >>> ACPI: SSDT 7EEB7F10, 0085 (r1 APPLE Cpu1Cst 3000 INTL 20050309) >>> ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) >>> processor ACPI_CPU:01: registered as cooling_device1 >>> ACPI: Processor [CPU1] (supports 8 throttling states) >>> Real Time Clock Driver v1.12b >>> intel_rng: FWH not detected >>> Linux agpgart interface v0.103 >>> agpgart-intel 0000:00:00.0: Intel 945GM Chipset >>> agpgart-intel 0000:00:00.0: detected 16124K stolen memory >>> agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000 >>> intelfb: Framebuffer driver for Intel(R) >>> 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/945GME/965G/965GM >>> chipsets >>> intelfb: Version 0.9.6 >>> intelfb 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 >>> intelfb: 00:02.0: Intel(R) 945GM, aperture size 256MB, stolen memory >>> 16124kB >>> intelfb: Non-CRT device is enabled ( LVDS port ). Disabling mode >>> switching. >>> intelfb: Video mode must be programmed at boot time. >>> Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled >>> floppy0: no floppy controllers found >>> brd: module loaded >>> loop: module loaded >>> Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI >>> Copyright (c) 1999-2006 Intel Corporation. >>> e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI >>> e100: Copyright(c) 1999-2006 Intel Corporation >>> sky2 driver version 1.22 >>> sky2 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 >>> sky2 0000:01:00.0: setting latency timer to 64 >>> sky2 0000:01:00.0: Yukon-2 EC chip revision 2 >>> sky2 0000:01:00.0: Marvell Yukon 88E8053 Gigabit Ethernet Controller >>> Part Number: Yukon 88E8053 >>> Engineering Level: Rev. 2.2 >>> Manufacturer: Marvell >>> sky2 0000:01:00.0: irq 24 for MSI/MSI-X >>> sky2 eth0: addr 00:19:e3:43:1c:a3 >>> console [netcon0] enabled >>> netconsole: network logging started >>> Linux video capture interface: v2.00 >>> usbcore: registered new interface driver uvcvideo >>> USB Video Class driver (v0.1.0) >>> Uniform Multi-Platform E-IDE driver >>> piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x02) >>> pci 0000:00:1f.1: power state changed by ACPI to D0 >>> pci 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 >>> piix 0000:00:1f.1: not 100% native mode: will probe irqs later >>> ide0: BM-DMA at 0x20b0-0x20b7 >>> ide1: BM-DMA at 0x20b8-0x20bf >>> Probing IDE interface ide0... >>> hda: HL-DT-ST DVDRW GSA-S10N, ATAPI CD/DVD-ROM drive >>> hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 >>> hda: UDMA/33 mode selected >>> Probing IDE interface ide1... >>> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 >>> ide1 at 0x170-0x177,0x376 on irq 15 >>> ide_generic: please use "probe_mask=0x3f" module parameter for probing >>> all legacy ISA IDE ports >>> ide-gd driver 1.18 >>> ide-cd driver 5.00 >>> ide-cd: hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache >>> Uniform CD-ROM driver Revision: 3.20 >>> 3ware Storage Controller device driver for Linux v1.26.02.002. >>> Driver 'sd' needs updating - please use bus_type methods >>> Driver 'sr' needs updating - please use bus_type methods >>> ata_piix 0000:00:1f.2: version 2.12 >>> ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 >>> ata_piix 0000:00:1f.2: MAP [ P0 P2 -- -- ] >>> ata_piix 0000:00:1f.2: setting latency timer to 64 >>> scsi0 : ata_piix >>> scsi1 : ata_piix >>> ata1: SATA max UDMA/133 cmd 0x20c8 ctl 0x20ec bmdma 0x20a0 irq 19 >>> ata2: SATA max UDMA/133 cmd 0x20c0 ctl 0x20e8 bmdma 0x20a8 irq 19 >>> ata1.01: ATA-7: ST9160821AS, 3.CAE, max UDMA/133 >>> ata1.01: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32) >>> ata1.01: configured for UDMA/133 >>> isa bounce pool size: 16 pages >>> scsi 0:0:1:0: Direct-Access ATA ST9160821AS 3.CA PQ: 0 ANSI: >>> 5 >>> sd 0:0:1:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) >>> sd 0:0:1:0: [sda] Write Protect is off >>> sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00 >>> sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't >>> support DPO or FUA >>> sd 0:0:1:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) >>> sd 0:0:1:0: [sda] Write Protect is off >>> sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00 >>> sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't >>> support DPO or FUA >>> sda: sda1 sda2 sda3 sda4 >>> sd 0:0:1:0: [sda] Attached SCSI disk >>> sd 0:0:1:0: Attached scsi generic sg0 type 0 >>> Fusion MPT base driver 3.04.07 >>> Copyright (c) 1999-2008 LSI Corporation >>> Fusion MPT SPI Host driver 3.04.07 >>> ohci1394 0000:03:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 >>> ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[19] >>> MMIO=[90000000-900007ff] Max Packet=[2048] IR/IT contexts=[8/8] >>> ieee1394: raw1394: /dev/raw1394 device initialized >>> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver >>> ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 21 (level, low) -> IRQ 21 >>> ehci_hcd 0000:00:1d.7: setting latency timer to 64 >>> ehci_hcd 0000:00:1d.7: EHCI Host Controller >>> ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 >>> ehci_hcd 0000:00:1d.7: debug port 1 >>> ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported >>> ehci_hcd 0000:00:1d.7: irq 21, io mem 0x90445400 >>> ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 >>> usb usb1: configuration #1 chosen from 1 choice >>> hub 1-0:1.0: USB hub found >>> hub 1-0:1.0: 8 ports detected >>> ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver >>> uhci_hcd: USB Universal Host Controller Interface driver >>> uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 >>> uhci_hcd 0000:00:1d.0: setting latency timer to 64 >>> uhci_hcd 0000:00:1d.0: UHCI Host Controller >>> uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 >>> uhci_hcd 0000:00:1d.0: irq 21, io base 0x00002080 >>> usb usb2: configuration #1 chosen from 1 choice >>> hub 2-0:1.0: USB hub found >>> hub 2-0:1.0: 2 ports detected >>> uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 >>> uhci_hcd 0000:00:1d.1: setting latency timer to 64 >>> uhci_hcd 0000:00:1d.1: UHCI Host Controller >>> uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 >>> uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 >>> usb usb3: configuration #1 chosen from 1 choice >>> hub 3-0:1.0: USB hub found >>> hub 3-0:1.0: 2 ports detected >>> uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 >>> uhci_hcd 0000:00:1d.2: setting latency timer to 64 >>> uhci_hcd 0000:00:1d.2: UHCI Host Controller >>> uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 >>> uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 >>> usb usb4: configuration #1 chosen from 1 choice >>> hub 4-0:1.0: USB hub found >>> hub 4-0:1.0: 2 ports detected >>> uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 >>> uhci_hcd 0000:00:1d.3: setting latency timer to 64 >>> uhci_hcd 0000:00:1d.3: UHCI Host Controller >>> uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 >>> uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002020 >>> usb usb5: configuration #1 chosen from 1 choice >>> hub 5-0:1.0: USB hub found >>> hub 5-0:1.0: 2 ports detected >>> usbcore: registered new interface driver usblp >>> Initializing USB Mass Storage driver... >>> usbcore: registered new interface driver usb-storage >>> USB Mass Storage support registered. >>> PNP: No PS/2 controller found. Probing ports directly. >>> i8042.c: No controller found. >>> mice: PS/2 mouse device common for all mice >>> device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: >>> dm-devel@redhat.com >>> cpuidle: using governor ladder >>> cpuidle: using governor menu >>> Marking TSC unstable due to TSC halts in idle >>> usbcore: registered new interface driver usbhid >>> usbhid: v2.6:USB HID core driver >>> oprofile: using NMI interrupt. >>> Netfilter messages via NETLINK v0.30. >>> nf_conntrack version 0.5.0 (16384 buckets, 65536 max) >>> CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use >>> nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or >>> sysctl net.netfilter.nf_conntrack_acct=1 to enable it. >>> xt_time: kernel timezone is -0000 >>> ip_tables: (C) 2000-2006 Netfilter Core Team >>> arp_tables: (C) 2002 David S. Miller >>> TCP cubic registered >>> NET: Registered protocol family 10 >>> IPv6 over IPv4 tunneling driver >>> NET: Registered protocol family 17 >>> RPC: Registered udp transport module. >>> RPC: Registered tcp transport module. >>> registered taskstats version 1 >>> Freeing unused kernel memory: 372k freed >>> usb 1-1: new high speed USB device using ehci_hcd and address 2 >>> usb 1-1: configuration #1 chosen from 1 choice >>> scsi2 : SCSI emulation for USB Mass Storage devices >>> usb-storage: device found at 2 >>> usb-storage: waiting for device to settle before scanning >>> usb 1-3: new high speed USB device using ehci_hcd and address 4 >>> usb 1-3: configuration #1 chosen from 1 choice >>> hub 1-3:1.0: USB hub found >>> hub 1-3:1.0: 2 ports detected >>> Clocksource tsc unstable (delta = -265511863 ns) >>> usb 1-4: new high speed USB device using ehci_hcd and address 5 >>> usb 1-4: configuration #1 chosen from 1 choice >>> ieee1394: Host added: ID:BUS[0-00:1023] GUID[001cb3fffe8ab416] >>> usb 2-2: new full speed USB device using uhci_hcd and address 2 >>> usb 2-2: configuration #1 chosen from 1 choice >>> input: Apple Computer Apple Internal Keyboard / Trackpad as >>> /class/input/input4 >>> apple 0003:05AC:021A.0001: input: USB HID v1.11 Keyboard [Apple >>> Computer Apple Internal Keyboard / Trackpad] on >>> usb-0000:00:1d.0-2/input0 >>> input: Apple Computer Apple Internal Keyboard / Trackpad as >>> /class/input/input5 >>> apple 0003:05AC:021A.0002: input: USB HID v1.11 Device [Apple Computer >>> Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2/input2 >>> usb 4-2: new full speed USB device using uhci_hcd and address 2 >>> usb 4-2: configuration #1 chosen from 1 choice >>> generic-usb 0003:05AC:8240.0003: claimed by neither input, hiddev nor >>> hidraw >>> usb 5-1: new full speed USB device using uhci_hcd and address 2 >>> usb 5-1: configuration #1 chosen from 1 choice >>> input: HID 05ac:1000 as /class/input/input6 >>> generic-usb 0003:05AC:1000.0004: input: USB HID v1.11 Keyboard [HID >>> 05ac:1000] on usb-0000:00:1d.3-1/input0 >>> input: HID 05ac:1000 as /class/input/input7 >>> generic-usb 0003:05AC:1000.0005: input: USB HID v1.11 Mouse [HID >>> 05ac:1000] on usb-0000:00:1d.3-1/input1 >>> usb 1-3.1: new high speed USB device using ehci_hcd and address 8 >>> usb 1-3.1: configuration #1 chosen from 1 choice >>> hub 1-3.1:1.0: USB hub found >>> hub 1-3.1:1.0: 4 ports detected >>> usb 1-3.2: new low speed USB device using ehci_hcd and address 9 >>> usb 1-3.2: configuration #1 chosen from 1 choice >>> input: Logitech USB Mouse as /class/input/input8 >>> generic-usb 0003:046D:C00C.0006: input: USB HID v1.10 Mouse [Logitech >>> USB Mouse] on usb-0000:00:1d.7-3.2/input0 >>> usb 1-3.1.1: new high speed USB device using ehci_hcd and address 10 >>> usb 1-3.1.1: configuration #1 chosen from 1 choice >>> scsi3 : SCSI emulation for USB Mass Storage devices >>> usb-storage: device found at 10 >>> usb-storage: waiting for device to settle before scanning >>> usb 1-3.1.3: new high speed USB device using ehci_hcd and address 11 >>> usb 1-3.1.3: configuration #1 chosen from 1 choice >>> hub 1-3.1.3:1.0: USB hub found >>> hub 1-3.1.3:1.0: 3 ports detected >>> usb 1-3.1.4: new high speed USB device using ehci_hcd and address 12 >>> usb 1-3.1.4: configuration #1 chosen from 1 choice >>> scsi4 : SCSI emulation for USB Mass Storage devices >>> usb-storage: device found at 12 >>> usb-storage: waiting for device to settle before scanning >>> usb 1-3.1.3.1: new low speed USB device using ehci_hcd and address 13 >>> usb 1-3.1.3.1: configuration #1 chosen from 1 choice >>> input: No brand KVM as /class/input/input9 >>> generic-usb 0003:10D5:5552.0007: input: USB HID v1.10 Keyboard [No >>> brand KVM] on usb-0000:00:1d.7-3.1.3.1/input0 >>> input: No brand KVM as /class/input/input10 >>> generic-usb 0003:10D5:5552.0008: input: USB HID v1.10 Mouse [No brand >>> KVM] on usb-0000:00:1d.7-3.1.3.1/input1 >>> scsi 2:0:0:0: Direct-Access Ext Hard Disk PQ: 0 ANSI: >>> 4 >>> sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) >>> sd 2:0:0:0: [sdb] Write Protect is off >>> sd 2:0:0:0: [sdb] Mode Sense: 10 00 00 00 >>> sd 2:0:0:0: [sdb] Assuming drive cache: write through >>> sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) >>> sd 2:0:0:0: [sdb] Write Protect is off >>> sd 2:0:0:0: [sdb] Mode Sense: 10 00 00 00 >>> sd 2:0:0:0: [sdb] Assuming drive cache: write through >>> sdb: sdb1 < sdb5 sdb6 > >>> sd 2:0:0:0: [sdb] Attached SCSI disk >>> sd 2:0:0:0: Attached scsi generic sg1 type 0 >>> usb-storage: device scan complete >>> kjournald starting. Commit interval 5 seconds >>> EXT3-fs: mounted filesystem with ordered data mode. >>> udev: renamed network interface eth0 to eth1 >>> scsi 3:0:0:0: Direct-Access Generic Flash HS-CF 4.44 PQ: 0 ANSI: >>> 0 >>> sd 3:0:0:0: [sdc] Attached SCSI removable disk >>> sd 3:0:0:0: Attached scsi generic sg2 type 0 >>> usb-storage: device scan complete >>> applesmc: Apple MacBook (v2) detected: >>> applesmc: - Model with accelerometer >>> applesmc: - Model without light sensors and backlight >>> applesmc: - Model with 10 temperature sensors >>> applesmc: device has already been initialized (0xe0, 0xf8). >>> applesmc: device successfully initialized. >>> applesmc: 1 fans found. >>> input: applesmc as /class/input/input11 >>> applesmc: driver successfully loaded. >>> input: PC Speaker as /class/input/input12 >>> scsi 4:0:0:0: Direct-Access Maxtor 6 L200R0 BAH4 PQ: 0 ANSI: >>> 0 >>> sd 4:0:0:0: [sdd] 398297087 512-byte hardware sectors: (203 GB/189 GiB) >>> sd 4:0:0:0: [sdd] Write Protect is off >>> sd 4:0:0:0: [sdd] Mode Sense: 03 00 00 00 >>> sd 4:0:0:0: [sdd] Assuming drive cache: write through >>> sd 4:0:0:0: [sdd] 398297087 512-byte hardware sectors: (203 GB/189 GiB) >>> sd 4:0:0:0: [sdd] Write Protect is off >>> sd 4:0:0:0: [sdd] Mode Sense: 03 00 00 00 >>> sd 4:0:0:0: [sdd] Assuming drive cache: write through >>> sdd: sdd1 >>> sd 4:0:0:0: [sdd] Attached SCSI disk >>> sd 4:0:0:0: Attached scsi generic sg3 type 0 >>> usb-storage: device scan complete >>> appletouch: Geyser mode initialized. >>> input: appletouch as /class/input/input13 >>> usbcore: registered new interface driver appletouch >>> HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 >>> HDA Intel 0000:00:1b.0: setting latency timer to 64 >>> hda_codec: STAC922x, Apple subsys_id=106b2200 >>> input: HDA Intel Line In at Ext Left Jack as /class/input/input14 >>> input: HDA Intel Mic at Ext Left Jack as /class/input/input15 >>> input: HDA Intel HP Out at Ext Left Jack as /class/input/input16 >>> EXT3 FS on dm-2, internal journal >>> fuse init (API version 7.11) >>> usbcore: registered new interface driver usbserial >>> USB Serial support registered for generic >>> usbcore: registered new interface driver usbserial_generic >>> usbserial: USB Serial Driver core >>> USB Serial support registered for pl2303 >>> usbcore: registered new interface driver pl2303 >>> pl2303: Prolific PL2303 USB to serial adaptor driver >>> EXT4-fs: barriers enabled >>> kjournald2 starting: pid 4443, dev dm-0:8, commit interval 5 seconds >>> EXT4 FS on dm-0, internal journal on dm-0:8 >>> EXT4-fs: delayed allocation enabled >>> EXT4-fs: mballoc enabled >>> EXT4-fs: mounted filesystem dm-0 with ordered data mode >>> EXT4-fs: barriers enabled >>> kjournald2 starting: pid 4444, dev dm-4:8, commit interval 5 seconds >>> EXT4 FS on dm-4, internal journal on dm-4:8 >>> EXT4-fs: delayed allocation enabled >>> EXT4-fs: mballoc enabled >>> EXT4-fs: mounted filesystem dm-4 with ordered data mode >>> EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended >>> Adding 1048568k swap on /dev/mapper/s-swap. Priority:-1 extents:1 >>> across:1048568k >>> sky2 eth1: enabling interface >>> ADDRCONF(NETDEV_UP): eth1: link is not ready >>> sky2 eth1: Link is up at 1000 Mbps, full duplex, flow control both >>> ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready >>> eth1: no IPv6 routers present >>> [drm] Initialized drm 1.1.0 20060810 >>> pci 0000:00:02.0: setting latency timer to 64 >>> [drm] Initialized i915 1.6.0 20080730 on minor 0 >>> JBD: barrier-based sync failed on dm-0:8 - disabling barriers >>> CE: hpet increasing min_delta_ns to 15000 nsec >>> ACPI: EC: GPE storm detected, transactions will use polling mode >> >> > -- > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ > I see ACPI: EC: GPE storm detected, transactions will use polling mode which might cause stuck-age(try booting without the battery), as for the kernel itself I had no issue with all the way up to 2.6.29-rc8-00302-ge2fad3f (a few hours before the initial release of 2.6.29) if you need my .config let me know(although its not pretty). -- Justin P. Mattock ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-03-30 3:18 ` Trenton D. Adams 2009-03-30 4:03 ` Justin Mattock @ 2009-03-30 4:55 ` Trenton D. Adams 2009-03-30 7:33 ` Trenton D. Adams 1 sibling, 1 reply; 15+ messages in thread From: Trenton D. Adams @ 2009-03-30 4:55 UTC (permalink / raw) To: Morten P.D. Stevens; +Cc: Linux Kernel Mailing List On Sun, Mar 29, 2009 at 9:18 PM, Trenton D. Adams <trenton.d.adams@gmail.com> wrote: > I recall it working on 2.6.28, but i didn't have vanilla sources > installed. I used 2.6.28 gentoo sources. I'm just compiling 2.6.28 > as we speak, as I figured you'd ask. I've marked 2.6.29 as bad with > "git bisect". I'll let you know when I've narrowed it down for you. > Can't wait to try "git bisect" *big smile*. Yep, works fine on 2.6.28. On 2.6.29, it does not unmount drives and such. I may not be able to finish with git bisect today, as I have to work in the morning. But, I'll try and wrap it up tomorrow if possible. Git reports so far... tdamac linux # git bisect bad Bisecting: 744 revisions left to test after this [bb26c6c29b7cc9f39e491b074b09f3c284738d36] Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6 tdamac linux # git bisect log git bisect start # bad: [8e0ee43bc2c3e19db56a4adaa9a9b04ce885cd84] Linux 2.6.29 git bisect bad 8e0ee43bc2c3e19db56a4adaa9a9b04ce885cd84 # good: [4a6908a3a050aacc9c3a2f36b276b46c0629ad91] Linux 2.6.28 git bisect good 4a6908a3a050aacc9c3a2f36b276b46c0629ad91 # bad: [2774de17ba65130165a2cbca92e5a685581f7916] Staging: benet: build is broken unless CONFIG_NETPOLL is enabled git bisect bad 2774de17ba65130165a2cbca92e5a685581f7916 # bad: [ba744d5e290055d171c68067259fcc1e2721f542] block: reorder struct bio to remove padding on 64bit git bisect bad ba744d5e290055d171c68067259fcc1e2721f542 # bad: [54a696bd07c14d3b1192d03ce7269bc59b45209a] Merge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6 git bisect bad 54a696bd07c14d3b1192d03ce7269bc59b45209a ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-03-30 4:55 ` Trenton D. Adams @ 2009-03-30 7:33 ` Trenton D. Adams 2009-03-30 12:57 ` Alistair John Strachan 0 siblings, 1 reply; 15+ messages in thread From: Trenton D. Adams @ 2009-03-30 7:33 UTC (permalink / raw) To: Morten P.D. Stevens; +Cc: Linux Kernel Mailing List Okay, I'm thoroughly confused on my git bisect results. It doesn't appear to be working for me at all. Either way, the problem is with shutting down ALSA. It refuses to shut down. If I shut it down manually, before rebooting, it also refuses to shutdown. I can then reboot, and it will force a kill of ALSA. Anyhow, any ideas on git stuff? I just don't git it. :P I get this far... git bisect start # bad: [8e0ee43bc2c3e19db56a4adaa9a9b04ce885cd84] Linux 2.6.29 git bisect bad 8e0ee43bc2c3e19db56a4adaa9a9b04ce885cd84 # good: [4a6908a3a050aacc9c3a2f36b276b46c0629ad91] Linux 2.6.28 git bisect good 4a6908a3a050aacc9c3a2f36b276b46c0629ad91 # bad: [2774de17ba65130165a2cbca92e5a685581f7916] Staging: benet: build is broken unless CONFIG_NETPOLL is enabled git bisect bad 2774de17ba65130165a2cbca92e5a685581f7916 # bad: [ba744d5e290055d171c68067259fcc1e2721f542] block: reorder struct bio to remove padding on 64bit git bisect bad ba744d5e290055d171c68067259fcc1e2721f542 # bad: [54a696bd07c14d3b1192d03ce7269bc59b45209a] Merge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6 git bisect bad 54a696bd07c14d3b1192d03ce7269bc59b45209a # bad: [bb26c6c29b7cc9f39e491b074b09f3c284738d36] Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6 git bisect bad bb26c6c29b7cc9f39e491b074b09f3c284738d36 # bad: [a65056205cdf7efb96fb2558e4f1ec6bae2582ed] Merge branch 'topic/hda' into to-push git bisect bad a65056205cdf7efb96fb2558e4f1ec6bae2582ed Then, I mark the current (something in 2.6.28) one as good... # good: [86b3aa390b4b9925f16a21b98441fd7abdb9fff2] Merge branch 'topic/ca0106' into to-push git bisect good 86b3aa390b4b9925f16a21b98441fd7abdb9fff2 And I get this... tdamac linux # git bisect good Bisecting: 89 revisions left to test after this [b83923a3931a43df7397a7491f0c9d9b9d46624a] ALSA: hda - minor HDMI code cleanups tdamac linux # make kernelversion 2.6.27 So, if I mark that as good (arbitrarily because it's pre 2.6.28 which I assume is good), it jumps back to pre 2.6.28 release tdamac linux # git bisect good Bisecting: 46 revisions left to test after this [0ff555192a8d20385d49d1c420e2e8d409b3c0da] Merge branch 'fix/hda' into topic/hda tdamac linux # make kernelversion 2.6.28-rc8 And, if I mark the 2.6.27 one as bad, it just remains on 2.6.27. ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-03-30 7:33 ` Trenton D. Adams @ 2009-03-30 12:57 ` Alistair John Strachan 2009-03-30 15:26 ` Trenton D. Adams 0 siblings, 1 reply; 15+ messages in thread From: Alistair John Strachan @ 2009-03-30 12:57 UTC (permalink / raw) To: Trenton D. Adams; +Cc: Morten P.D. Stevens, Linux Kernel Mailing List On Monday 30 March 2009 08:33:06 Trenton D. Adams wrote: [snip] > Then, I mark the current (something in 2.6.28) one as good... > # good: [86b3aa390b4b9925f16a21b98441fd7abdb9fff2] Merge branch > 'topic/ca0106' into to-push > git bisect good 86b3aa390b4b9925f16a21b98441fd7abdb9fff2 > > And I get this... > tdamac linux # git bisect good > Bisecting: 89 revisions left to test after this > [b83923a3931a43df7397a7491f0c9d9b9d46624a] ALSA: hda - minor HDMI code > cleanups tdamac linux # make kernelversion > 2.6.27 > > So, if I mark that as good (arbitrarily because it's pre 2.6.28 which > I assume is good), it jumps back to pre 2.6.28 release > tdamac linux # git bisect good > Bisecting: 46 revisions left to test after this > [0ff555192a8d20385d49d1c420e2e8d409b3c0da] Merge branch 'fix/hda' into > topic/hda tdamac linux # make kernelversion > 2.6.28-rc8 > > And, if I mark the 2.6.27 one as bad, it just remains on 2.6.27. Don't worry about the kernel version it generates. Git bisections traverse merged branches, including those that weren't rebased before being merged (in fact the preferred work flow). I usually add "-bisect" to CONFIG_LOCALVERSION so I can isolate my work in progress bisection from system kernels. You can trust git to involve only relevant commits between your initial "good" and "bad" markers; don't add more unless you have to. Sometimes you may need to "shift" the bisection midpoint if you encounter build breakage. You should be able to find comments Linus made on the subject by searching the LKML archive for "git bisect visualize". -- Cheers, Alistair. ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-03-30 12:57 ` Alistair John Strachan @ 2009-03-30 15:26 ` Trenton D. Adams 2009-03-30 18:44 ` Alistair John Strachan 0 siblings, 1 reply; 15+ messages in thread From: Trenton D. Adams @ 2009-03-30 15:26 UTC (permalink / raw) To: Alistair John Strachan; +Cc: Morten P.D. Stevens, Linux Kernel Mailing List On Mon, Mar 30, 2009 at 6:57 AM, Alistair John Strachan <alistair@devzero.co.uk> wrote: > On Monday 30 March 2009 08:33:06 Trenton D. Adams wrote: >> >> And, if I mark the 2.6.27 one as bad, it just remains on 2.6.27. > > Don't worry about the kernel version it generates. Git bisections traverse > merged branches, including those that weren't rebased before being merged (in > fact the preferred work flow). I usually add "-bisect" to CONFIG_LOCALVERSION > so I can isolate my work in progress bisection from system kernels. > > You can trust git to involve only relevant commits between your initial "good" > and "bad" markers; don't add more unless you have to. Sometimes you may need > to "shift" the bisection midpoint if you encounter build breakage. You should > be able to find comments Linus made on the subject by searching the LKML > archive for "git bisect visualize". > > -- > Cheers, > Alistair. > Okay, so are you saying that switching back to 2.6.27 is okay, because the patch that caused this problem may have been created in 2.6.27 (as a patch to the released version perhaps), not applied to 2.6.28, and then applied to 2.6.29? ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-03-30 15:26 ` Trenton D. Adams @ 2009-03-30 18:44 ` Alistair John Strachan 2009-03-31 5:11 ` Trenton D. Adams 0 siblings, 1 reply; 15+ messages in thread From: Alistair John Strachan @ 2009-03-30 18:44 UTC (permalink / raw) To: Trenton D. Adams; +Cc: Morten P.D. Stevens, Linux Kernel Mailing List On Monday 30 March 2009 16:26:13 Trenton D. Adams wrote: > On Mon, Mar 30, 2009 at 6:57 AM, Alistair John Strachan > > <alistair@devzero.co.uk> wrote: > > On Monday 30 March 2009 08:33:06 Trenton D. Adams wrote: > >> And, if I mark the 2.6.27 one as bad, it just remains on 2.6.27. > > > > Don't worry about the kernel version it generates. Git bisections > > traverse merged branches, including those that weren't rebased before > > being merged (in fact the preferred work flow). I usually add "-bisect" > > to CONFIG_LOCALVERSION so I can isolate my work in progress bisection > > from system kernels. > > > > You can trust git to involve only relevant commits between your initial > > "good" and "bad" markers; don't add more unless you have to. Sometimes > > you may need to "shift" the bisection midpoint if you encounter build > > breakage. You should be able to find comments Linus made on the subject > > by searching the LKML archive for "git bisect visualize". > > > > -- > > Cheers, > > Alistair. > > Okay, so are you saying that switching back to 2.6.27 is okay, because > the patch that caused this problem may have been created in 2.6.27 (as > a patch to the released version perhaps), not applied to 2.6.28, and > then applied to 2.6.29? Yes. Give "gitk" a shot with your revision ID, it should be quite illuminating. -- Cheers, Alistair. ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-03-30 18:44 ` Alistair John Strachan @ 2009-03-31 5:11 ` Trenton D. Adams 2009-04-01 5:19 ` Trenton D. Adams 0 siblings, 1 reply; 15+ messages in thread From: Trenton D. Adams @ 2009-03-31 5:11 UTC (permalink / raw) To: Alistair John Strachan; +Cc: Morten P.D. Stevens, Linux Kernel Mailing List Okay, I'm getting close. But, I may not finish the git bisect tonight. I had to go to dinner at my parent's place, and that sucked up a bit of my time. I think I'll likely be finished tomorrow. ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-03-31 5:11 ` Trenton D. Adams @ 2009-04-01 5:19 ` Trenton D. Adams 2009-04-02 0:30 ` Trenton D. Adams 0 siblings, 1 reply; 15+ messages in thread From: Trenton D. Adams @ 2009-04-01 5:19 UTC (permalink / raw) To: Alistair John Strachan; +Cc: Morten P.D. Stevens, Linux Kernel Mailing List Okay, git doesn't know what to do in my circumstances. I'm thinking that multiple changes have combined to cause the problem, because the one that git claims is the last bad commit, can't be. In 30d72e9f614e7bd76e28d4d92bd54d90a96905bb, the last one to be marked good, I had to move the power_save inside of an "ifdef", in order for it to compile, which is the exact same fix that 11cd41b893895c76a8f9bee9467f4b0869b5eeb3 provides. So, it's got to be a combo problem of some sort. Here's the log. git bisect start # bad: [8e0ee43bc2c3e19db56a4adaa9a9b04ce885cd84] Linux 2.6.29 git bisect bad 8e0ee43bc2c3e19db56a4adaa9a9b04ce885cd84 # good: [4a6908a3a050aacc9c3a2f36b276b46c0629ad91] Linux 2.6.28 git bisect good 4a6908a3a050aacc9c3a2f36b276b46c0629ad91 # bad: [2774de17ba65130165a2cbca92e5a685581f7916] Staging: benet: build is broken unless CONFIG_NETPOLL is enabled git bisect bad 2774de17ba65130165a2cbca92e5a685581f7916 # bad: [ba744d5e290055d171c68067259fcc1e2721f542] block: reorder struct bio to remove padding on 64bit git bisect bad ba744d5e290055d171c68067259fcc1e2721f542 # bad: [54a696bd07c14d3b1192d03ce7269bc59b45209a] Merge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6 git bisect bad 54a696bd07c14d3b1192d03ce7269bc59b45209a # bad: [bb26c6c29b7cc9f39e491b074b09f3c284738d36] Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6 git bisect bad bb26c6c29b7cc9f39e491b074b09f3c284738d36 # bad: [a65056205cdf7efb96fb2558e4f1ec6bae2582ed] Merge branch 'topic/hda' into to-push git bisect bad a65056205cdf7efb96fb2558e4f1ec6bae2582ed # good: [86b3aa390b4b9925f16a21b98441fd7abdb9fff2] Merge branch 'topic/ca0106' into to-push git bisect good 86b3aa390b4b9925f16a21b98441fd7abdb9fff2 # good: [b83923a3931a43df7397a7491f0c9d9b9d46624a] ALSA: hda - minor HDMI code cleanups git bisect good b83923a3931a43df7397a7491f0c9d9b9d46624a # bad: [0ff555192a8d20385d49d1c420e2e8d409b3c0da] Merge branch 'fix/hda' into topic/hda git bisect bad 0ff555192a8d20385d49d1c420e2e8d409b3c0da # skip: [1289e9e8b42f973f2ab39e5f4f2239ff826c27e9] ALSA: hda - Modularize HD-audio driver git bisect skip 1289e9e8b42f973f2ab39e5f4f2239ff826c27e9 # bad: [11cd41b893895c76a8f9bee9467f4b0869b5eeb3] ALSA: hda - Fix build error with CONFIG_SND_HDA_POWER_SAVE git bisect bad 11cd41b893895c76a8f9bee9467f4b0869b5eeb3 # good: [0e19e7d2bff0ec04fe4dc920c580d8a321afa07f] Merge branch 'topic/fix/hda' into topic/hda git bisect good 0e19e7d2bff0ec04fe4dc920c580d8a321afa07f # good: [4f199629b0fba95fd5caecbf35ed68417d9a9b7a] ALSA: sound/pci/hda/hda_codec.c: cleanup kernel-doc git bisect good 4f199629b0fba95fd5caecbf35ed68417d9a9b7a # good: [529bd6c4a63f8468fd66f63fdc22d7070439b3cd] ALSA: hda - Fix PCM reconfigure git bisect good 529bd6c4a63f8468fd66f63fdc22d7070439b3cd # good: [30d72e9f614e7bd76e28d4d92bd54d90a96905bb] ALSA: hda - Fix creation of automatic capture mixers git bisect good 30d72e9f614e7bd76e28d4d92bd54d90a96905bb So, the problem appears to exist in the changes between these two commits... git diff 0e19e7d2bff0ec04fe4dc920c580d8a321afa07f 11cd41b893895c76a8f9bee9467f4b0869b5eeb3 | less I may play around a little more at a later date, but I'm busy for the next few days. ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-04-01 5:19 ` Trenton D. Adams @ 2009-04-02 0:30 ` Trenton D. Adams 2009-04-05 7:03 ` Trenton D. Adams 0 siblings, 1 reply; 15+ messages in thread From: Trenton D. Adams @ 2009-04-02 0:30 UTC (permalink / raw) To: Alistair John Strachan; +Cc: Morten P.D. Stevens, Linux Kernel Mailing List Morton, did you see this one fly by? ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 2.6.29 on MacBook 2,1 fails to reboot 2009-04-02 0:30 ` Trenton D. Adams @ 2009-04-05 7:03 ` Trenton D. Adams 0 siblings, 0 replies; 15+ messages in thread From: Trenton D. Adams @ 2009-04-05 7:03 UTC (permalink / raw) To: Alistair John Strachan; +Cc: Morten P.D. Stevens, Linux Kernel Mailing List I have more information on this. I put an strace in the shutdown script for alsa sound... strace -T -f -o /root/${1}-strace.txt rmmod --wait "$1" ${1} is the module name... Oops, I just noticed that it finally quit. Some of the modules were unloaded successfully, others, after several minutes, got an error. I have the strace for all of them if you want it. But, here's an example. Note the end where it says "resource temporarily unavailable". I also give a second strace snippet after this one... snd_hda_codec-strace.txt 12181 execve("/sbin/rmmod", ["rmmod", "--wait", "snd_hda_codec"], [/* 13 vars */]) = 0 <0.000079> 12181 brk(0) = 0x604000 <0.000007> 12181 mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x7f224f8c2000 <0.000008> 12181 mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x7f224f8c1000 <0.000007> 12181 access("/etc/ld.so.preload", R_OK) = -1 ENOENT (No such file or directory) <0.000010> 12181 open("/etc/ld.so.cache", O_RDONLY) = 3 <0.000009> 12181 fstat(3, {st_mode=S_IFREG|0644, st_size=214104, ...}) = 0 <0.000007> 12181 mmap(NULL, 214104, PROT_READ, MAP_PRIVATE, 3, 0) = 0x7f224f88c000 <0.000008> 12181 close(3) = 0 <0.000007> 12181 open("/lib/libz.so.1", O_RDONLY) = 3 <0.000011> 12181 read(3, "\177ELF\2\1\1\0\0\0\0\0\0\0\0\0\3\0>\0\1\0\0\0\340\37\0\0\0\0\0\0@"..., 832) = 832 <0.000007> 12181 fstat(3, {st_mode=S_IFREG|0755, st_size=84272, ...}) = 0 <0.000006> 12181 mmap(NULL, 2179560, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0x7f224f494000 <0.000009> 12181 mprotect(0x7f224f4a8000, 2093056, PROT_NONE) = 0 <0.000009> 12181 mmap(0x7f224f6a7000, 8192, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x13000) = 0x7f224f6a7000 <0.000010> 12181 close(3) = 0 <0.000006> 12181 open("/lib/libc.so.6", O_RDONLY) = 3 <0.000011> 12181 read(3, "\177ELF\2\1\1\0\0\0\0\0\0\0\0\0\3\0>\0\1\0\0\0\300\345\1\0\0\0\0\0@"..., 832) = 832 <0.000007> 12181 fstat(3, {st_mode=S_IFREG|0755, st_size=1330352, ...}) = 0 <0.000006> 12181 mmap(NULL, 3437208, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0x7f224f14c000 <0.000009> 12181 mprotect(0x7f224f28b000, 2093056, PROT_NONE) = 0 <0.000009> 12181 mmap(0x7f224f48a000, 20480, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x13e000) = 0x7f224f48a000 <0.000010> 12181 mmap(0x7f224f48f000, 17048, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x7f224f48f000 <0.000009> 12181 close(3) = 0 <0.000009> 12181 mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x7f224f88b000 <0.000008> 12181 mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x7f224f88a000 <0.000007> 12181 arch_prctl(ARCH_SET_FS, 0x7f224f88a6f0) = 0 <0.000007> 12181 mprotect(0x7f224f48a000, 16384, PROT_READ) = 0 <0.000009> 12181 mprotect(0x7f224f6a7000, 4096, PROT_READ) = 0 <0.000008> 12181 mprotect(0x602000, 4096, PROT_READ) = 0 <0.000009> 12181 mprotect(0x7f224f8c3000, 4096, PROT_READ) = 0 <0.000008> 12181 munmap(0x7f224f88c000, 214104) = 0 <0.000012> 12181 create_module(NULL, 0) = -1 ENOSYS (Function not implemented) <0.000006> 12181 delete_module("snd_hda_codec", O_RDONLY|O_EXCL) = -1 EAGAIN (Resource temporarily unavailable) <0.000011> 12181 brk(0) = 0x604000 <0.000007> 12181 brk(0x625000) = 0x625000 <0.000008> 12181 write(2, "ERROR: Removing 'snd_hda_codec': "..., 66) = 66 <0.000016> 12181 exit_group(1) = ? Note the one below has a different error... snd_hda_codec_idt-strace.txt 12174 create_module(NULL, 0) = -1 ENOSYS (Function not implemented) <0.000006> 12174 delete_module("snd_hda_codec_idt", O_RDONLY|O_EXCL) = -1 EBUSY (Device or resource busy) <0.000009> 12174 brk(0) = 0x604000 <0.000007> 12174 brk(0x625000) = 0x625000 <0.000008> 12174 write(2, "ERROR: Removing 'snd_hda_codec_id"..., 61) = 61 <0.000018> 12174 exit_group(1) = ? On Wed, Apr 1, 2009 at 6:30 PM, Trenton D. Adams <trenton.d.adams@gmail.com> wrote: > Morton, did you see this one fly by? > ^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2009-04-05 7:03 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-03-30 2:04 2.6.29 on MacBook 2,1 fails to reboot Trenton Adams
2009-03-30 2:46 ` Morten P.D. Stevens
2009-03-30 2:54 ` Trenton Adams
2009-03-30 3:17 ` Morten P.D. Stevens
[not found] ` <897274600903292015n44005d12l82b0fafd170d6292@mail.gmail.com>
2009-03-30 3:18 ` Trenton D. Adams
2009-03-30 4:03 ` Justin Mattock
2009-03-30 4:55 ` Trenton D. Adams
2009-03-30 7:33 ` Trenton D. Adams
2009-03-30 12:57 ` Alistair John Strachan
2009-03-30 15:26 ` Trenton D. Adams
2009-03-30 18:44 ` Alistair John Strachan
2009-03-31 5:11 ` Trenton D. Adams
2009-04-01 5:19 ` Trenton D. Adams
2009-04-02 0:30 ` Trenton D. Adams
2009-04-05 7:03 ` Trenton D. Adams
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox