* [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
@ 2010-01-13 11:58 Adrian Hunter
2010-01-13 12:03 ` Mark Brown
0 siblings, 1 reply; 9+ messages in thread
From: Adrian Hunter @ 2010-01-13 11:58 UTC (permalink / raw)
To: Liam Girdwood; +Cc: Mark Brown, Roger Quadros, LKML
>From bd97e65b280be528239e3932da8be512ce7785ed Mon Sep 17 00:00:00 2001
From: Adrian Hunter <adrian.hunter@nokia.com>
Date: Tue, 12 Jan 2010 12:25:13 +0200
Subject: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
Add a field to specify a delay for the start-up time of
a fixed voltage regulator.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
---
drivers/regulator/fixed.c | 5 +++++
include/linux/regulator/fixed.h | 2 ++
2 files changed, 7 insertions(+), 0 deletions(-)
diff --git a/drivers/regulator/fixed.c b/drivers/regulator/fixed.c
index f9f516a..40d4080 100644
--- a/drivers/regulator/fixed.c
+++ b/drivers/regulator/fixed.c
@@ -24,12 +24,14 @@
#include <linux/regulator/driver.h>
#include <linux/regulator/fixed.h>
#include <linux/gpio.h>
+#include <linux/delay.h>
struct fixed_voltage_data {
struct regulator_desc desc;
struct regulator_dev *dev;
int microvolts;
int gpio;
+ unsigned delay;
unsigned enable_high:1;
unsigned is_enabled:1;
};
@@ -48,6 +50,8 @@ static int fixed_voltage_enable(struct regulator_dev *dev)
if (gpio_is_valid(data->gpio)) {
gpio_set_value_cansleep(data->gpio, data->enable_high);
data->is_enabled = 1;
+ if (data->delay)
+ udelay(data->delay);
}
return 0;
@@ -117,6 +121,7 @@ static int regulator_fixed_voltage_probe(struct platform_device *pdev)
drvdata->microvolts = config->microvolts;
drvdata->gpio = config->gpio;
+ drvdata->delay = config->delay;
if (gpio_is_valid(config->gpio)) {
drvdata->enable_high = config->enable_high;
diff --git a/include/linux/regulator/fixed.h b/include/linux/regulator/fixed.h
index e94a4a1..02edef1 100644
--- a/include/linux/regulator/fixed.h
+++ b/include/linux/regulator/fixed.h
@@ -25,6 +25,7 @@ struct regulator_init_data;
* @microvolts: Output voltage of regulator
* @gpio: GPIO to use for enable control
* set to -EINVAL if not used
+ * @delay: Start-up time in microseconds
* @enable_high: Polarity of enable GPIO
* 1 = Active high, 0 = Active low
* @enabled_at_boot: Whether regulator has been enabled at
@@ -41,6 +42,7 @@ struct fixed_voltage_config {
const char *supply_name;
int microvolts;
int gpio;
+ unsigned delay;
unsigned enable_high:1;
unsigned enabled_at_boot:1;
struct regulator_init_data *init_data;
--
1.6.0.4
^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
2010-01-13 11:58 [PATCH] regulator: Add 'start-up time' to fixed voltage regulators Adrian Hunter
@ 2010-01-13 12:03 ` Mark Brown
2010-01-13 12:15 ` Adrian Hunter
0 siblings, 1 reply; 9+ messages in thread
From: Mark Brown @ 2010-01-13 12:03 UTC (permalink / raw)
To: Adrian Hunter; +Cc: Liam Girdwood, Roger Quadros, LKML
On Wed, Jan 13, 2010 at 01:58:26PM +0200, Adrian Hunter wrote:
> Add a field to specify a delay for the start-up time of
> a fixed voltage regulator.
> Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
but...
> #include <linux/regulator/driver.h>
> #include <linux/regulator/fixed.h>
> #include <linux/gpio.h>
> +#include <linux/delay.h>
I think your MUA may have eaten the patch - it looks like the leading
spaces got stripped which is liable to confuse things.
> --- a/include/linux/regulator/fixed.h
> +++ b/include/linux/regulator/fixed.h
> @@ -25,6 +25,7 @@ struct regulator_init_data;
> * @microvolts: Output voltage of regulator
> * @gpio: GPIO to use for enable control
> * set to -EINVAL if not used
> + * @delay: Start-up time in microseconds
startup_delay? Just in case we think of another delay, though I'm
struggling to think of one right now so I'm not too worried.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
2010-01-13 12:03 ` Mark Brown
@ 2010-01-13 12:15 ` Adrian Hunter
2010-01-13 12:26 ` Mark Brown
0 siblings, 1 reply; 9+ messages in thread
From: Adrian Hunter @ 2010-01-13 12:15 UTC (permalink / raw)
To: Mark Brown; +Cc: Liam Girdwood, Quadros Roger (Nokia-D/Helsinki), LKML
Mark Brown wrote:
> On Wed, Jan 13, 2010 at 01:58:26PM +0200, Adrian Hunter wrote:
>
>> Add a field to specify a delay for the start-up time of
>> a fixed voltage regulator.
>
>> Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
>
> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
>
> but...
>
>> #include <linux/regulator/driver.h>
>> #include <linux/regulator/fixed.h>
>> #include <linux/gpio.h>
>> +#include <linux/delay.h>
>
> I think your MUA may have eaten the patch - it looks like the leading
> spaces got stripped which is liable to confuse things.
>
Are you sure? Looks fines to me.
>> --- a/include/linux/regulator/fixed.h
>> +++ b/include/linux/regulator/fixed.h
>> @@ -25,6 +25,7 @@ struct regulator_init_data;
>> * @microvolts: Output voltage of regulator
>> * @gpio: GPIO to use for enable control
>> * set to -EINVAL if not used
>> + * @delay: Start-up time in microseconds
>
> startup_delay? Just in case we think of another delay, though I'm
> struggling to think of one right now so I'm not too worried.
>
I am too lazy to change it unless there is something else too ;-)
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
2010-01-13 12:15 ` Adrian Hunter
@ 2010-01-13 12:26 ` Mark Brown
2010-01-13 12:55 ` Adrian Hunter
2010-01-13 13:11 ` Adrian Hunter
0 siblings, 2 replies; 9+ messages in thread
From: Mark Brown @ 2010-01-13 12:26 UTC (permalink / raw)
To: Adrian Hunter; +Cc: Liam Girdwood, Quadros Roger (Nokia-D/Helsinki), LKML
On Wed, Jan 13, 2010 at 02:15:10PM +0200, Adrian Hunter wrote:
> Mark Brown wrote:
> >>#include <linux/gpio.h>
> >>+#include <linux/delay.h>
> >I think your MUA may have eaten the patch - it looks like the leading
> >spaces got stripped which is liable to confuse things.
> Are you sure? Looks fines to me.
The above should be
> #include <linux/gpio.h>
> +#include <linux/delay.h>
IIRC ie, a one character indent on the context as well as the changed
lines.
> >startup_delay? Just in case we think of another delay, though I'm
> >struggling to think of one right now so I'm not too worried.
> I am too lazy to change it unless there is something else too ;-)
On the other hand the cross tree issues will be annoying if it's changed
later...
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
2010-01-13 12:26 ` Mark Brown
@ 2010-01-13 12:55 ` Adrian Hunter
2010-01-13 13:18 ` Mark Brown
2010-01-13 13:11 ` Adrian Hunter
1 sibling, 1 reply; 9+ messages in thread
From: Adrian Hunter @ 2010-01-13 12:55 UTC (permalink / raw)
To: Mark Brown; +Cc: Liam Girdwood, Quadros Roger (Nokia-D/Helsinki), LKML
Mark Brown wrote:
> On Wed, Jan 13, 2010 at 02:15:10PM +0200, Adrian Hunter wrote:
>> Mark Brown wrote:
>
>>>> #include <linux/gpio.h>
>>>> +#include <linux/delay.h>
>
>>> I think your MUA may have eaten the patch - it looks like the leading
>>> spaces got stripped which is liable to confuse things.
>
>> Are you sure? Looks fines to me.
>
> The above should be
>
> > #include <linux/gpio.h>
> > +#include <linux/delay.h>
>
> IIRC ie, a one character indent on the context as well as the changed
> lines.
>
I meant that the space is, in fact, there.
e.g. see http://lkml.org/lkml/2010/1/13/186
>>> startup_delay? Just in case we think of another delay, though I'm
>>> struggling to think of one right now so I'm not too worried.
>
>> I am too lazy to change it unless there is something else too ;-)
>
> On the other hand the cross tree issues will be annoying if it's changed
> later...
>
OK
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
2010-01-13 12:26 ` Mark Brown
2010-01-13 12:55 ` Adrian Hunter
@ 2010-01-13 13:11 ` Adrian Hunter
2010-01-13 13:18 ` Mark Brown
2010-01-14 19:54 ` Liam Girdwood
1 sibling, 2 replies; 9+ messages in thread
From: Adrian Hunter @ 2010-01-13 13:11 UTC (permalink / raw)
To: Mark Brown; +Cc: Liam Girdwood, Quadros Roger (Nokia-D/Helsinki), LKML
>From bd97e65b280be528239e3932da8be512ce7785ed Mon Sep 17 00:00:00 2001
From: Adrian Hunter <adrian.hunter@nokia.com>
Date: Tue, 12 Jan 2010 12:25:13 +0200
Subject: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
Add a field to specify a delay for the start-up time of
a fixed voltage regulator.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
---
drivers/regulator/fixed.c | 5 +++++
include/linux/regulator/fixed.h | 2 ++
2 files changed, 7 insertions(+), 0 deletions(-)
diff --git a/drivers/regulator/fixed.c b/drivers/regulator/fixed.c
index f9f516a..40d4080 100644
--- a/drivers/regulator/fixed.c
+++ b/drivers/regulator/fixed.c
@@ -24,12 +24,14 @@
#include <linux/regulator/driver.h>
#include <linux/regulator/fixed.h>
#include <linux/gpio.h>
+#include <linux/delay.h>
struct fixed_voltage_data {
struct regulator_desc desc;
struct regulator_dev *dev;
int microvolts;
int gpio;
+ unsigned startup_delay;
unsigned enable_high:1;
unsigned is_enabled:1;
};
@@ -48,6 +50,8 @@ static int fixed_voltage_enable(struct regulator_dev *dev)
if (gpio_is_valid(data->gpio)) {
gpio_set_value_cansleep(data->gpio, data->enable_high);
data->is_enabled = 1;
+ if (data->startup_delay)
+ udelay(data->startup_delay);
}
return 0;
@@ -117,6 +121,7 @@ static int regulator_fixed_voltage_probe(struct platform_device *pdev)
drvdata->microvolts = config->microvolts;
drvdata->gpio = config->gpio;
+ drvdata->startup_delay = config->startup_delay;
if (gpio_is_valid(config->gpio)) {
drvdata->enable_high = config->enable_high;
diff --git a/include/linux/regulator/fixed.h b/include/linux/regulator/fixed.h
index e94a4a1..02edef1 100644
--- a/include/linux/regulator/fixed.h
+++ b/include/linux/regulator/fixed.h
@@ -25,6 +25,7 @@ struct regulator_init_data;
* @microvolts: Output voltage of regulator
* @gpio: GPIO to use for enable control
* set to -EINVAL if not used
+ * @startup_delay: Start-up time in microseconds
* @enable_high: Polarity of enable GPIO
* 1 = Active high, 0 = Active low
* @enabled_at_boot: Whether regulator has been enabled at
@@ -41,6 +42,7 @@ struct fixed_voltage_config {
const char *supply_name;
int microvolts;
int gpio;
+ unsigned startup_delay;
unsigned enable_high:1;
unsigned enabled_at_boot:1;
struct regulator_init_data *init_data;
--
1.6.0.4
^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
2010-01-13 12:55 ` Adrian Hunter
@ 2010-01-13 13:18 ` Mark Brown
0 siblings, 0 replies; 9+ messages in thread
From: Mark Brown @ 2010-01-13 13:18 UTC (permalink / raw)
To: Adrian Hunter; +Cc: Liam Girdwood, Quadros Roger (Nokia-D/Helsinki), LKML
On Wed, Jan 13, 2010 at 02:55:03PM +0200, Adrian Hunter wrote:
> Mark Brown wrote:
> >IIRC ie, a one character indent on the context as well as the changed
> >lines.
> I meant that the space is, in fact, there.
> e.g. see http://lkml.org/lkml/2010/1/13/186
I see what the problem is here, you're sending in format=flowed which
means that MUAs that understand format=flowed will reindent the text on
reciept. The indentation of the original mail will be ignored.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
2010-01-13 13:11 ` Adrian Hunter
@ 2010-01-13 13:18 ` Mark Brown
2010-01-14 19:54 ` Liam Girdwood
1 sibling, 0 replies; 9+ messages in thread
From: Mark Brown @ 2010-01-13 13:18 UTC (permalink / raw)
To: Adrian Hunter; +Cc: Liam Girdwood, Quadros Roger (Nokia-D/Helsinki), LKML
On Wed, Jan 13, 2010 at 03:11:08PM +0200, Adrian Hunter wrote:
> From bd97e65b280be528239e3932da8be512ce7785ed Mon Sep 17 00:00:00 2001
> From: Adrian Hunter <adrian.hunter@nokia.com>
> Date: Tue, 12 Jan 2010 12:25:13 +0200
> Subject: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
>
> Add a field to specify a delay for the start-up time of
> a fixed voltage regulator.
>
> Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Looks good, thanks.
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
> ---
> drivers/regulator/fixed.c | 5 +++++
> include/linux/regulator/fixed.h | 2 ++
> 2 files changed, 7 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/regulator/fixed.c b/drivers/regulator/fixed.c
> index f9f516a..40d4080 100644
> --- a/drivers/regulator/fixed.c
> +++ b/drivers/regulator/fixed.c
> @@ -24,12 +24,14 @@
> #include <linux/regulator/driver.h>
> #include <linux/regulator/fixed.h>
> #include <linux/gpio.h>
> +#include <linux/delay.h>
>
> struct fixed_voltage_data {
> struct regulator_desc desc;
> struct regulator_dev *dev;
> int microvolts;
> int gpio;
> + unsigned startup_delay;
> unsigned enable_high:1;
> unsigned is_enabled:1;
> };
> @@ -48,6 +50,8 @@ static int fixed_voltage_enable(struct regulator_dev *dev)
> if (gpio_is_valid(data->gpio)) {
> gpio_set_value_cansleep(data->gpio, data->enable_high);
> data->is_enabled = 1;
> + if (data->startup_delay)
> + udelay(data->startup_delay);
> }
>
> return 0;
> @@ -117,6 +121,7 @@ static int regulator_fixed_voltage_probe(struct platform_device *pdev)
>
> drvdata->microvolts = config->microvolts;
> drvdata->gpio = config->gpio;
> + drvdata->startup_delay = config->startup_delay;
>
> if (gpio_is_valid(config->gpio)) {
> drvdata->enable_high = config->enable_high;
> diff --git a/include/linux/regulator/fixed.h b/include/linux/regulator/fixed.h
> index e94a4a1..02edef1 100644
> --- a/include/linux/regulator/fixed.h
> +++ b/include/linux/regulator/fixed.h
> @@ -25,6 +25,7 @@ struct regulator_init_data;
> * @microvolts: Output voltage of regulator
> * @gpio: GPIO to use for enable control
> * set to -EINVAL if not used
> + * @startup_delay: Start-up time in microseconds
> * @enable_high: Polarity of enable GPIO
> * 1 = Active high, 0 = Active low
> * @enabled_at_boot: Whether regulator has been enabled at
> @@ -41,6 +42,7 @@ struct fixed_voltage_config {
> const char *supply_name;
> int microvolts;
> int gpio;
> + unsigned startup_delay;
> unsigned enable_high:1;
> unsigned enabled_at_boot:1;
> struct regulator_init_data *init_data;
> --
> 1.6.0.4
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
2010-01-13 13:11 ` Adrian Hunter
2010-01-13 13:18 ` Mark Brown
@ 2010-01-14 19:54 ` Liam Girdwood
1 sibling, 0 replies; 9+ messages in thread
From: Liam Girdwood @ 2010-01-14 19:54 UTC (permalink / raw)
To: Adrian Hunter; +Cc: Mark Brown, Quadros Roger (Nokia-D/Helsinki), LKML
On Wed, 2010-01-13 at 15:11 +0200, Adrian Hunter wrote:
> From bd97e65b280be528239e3932da8be512ce7785ed Mon Sep 17 00:00:00 2001
> From: Adrian Hunter <adrian.hunter@nokia.com>
> Date: Tue, 12 Jan 2010 12:25:13 +0200
> Subject: [PATCH] regulator: Add 'start-up time' to fixed voltage regulators
>
> Add a field to specify a delay for the start-up time of
> a fixed voltage regulator.
>
Applied.
Thanks
Liam
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2010-01-14 19:55 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-01-13 11:58 [PATCH] regulator: Add 'start-up time' to fixed voltage regulators Adrian Hunter
2010-01-13 12:03 ` Mark Brown
2010-01-13 12:15 ` Adrian Hunter
2010-01-13 12:26 ` Mark Brown
2010-01-13 12:55 ` Adrian Hunter
2010-01-13 13:18 ` Mark Brown
2010-01-13 13:11 ` Adrian Hunter
2010-01-13 13:18 ` Mark Brown
2010-01-14 19:54 ` Liam Girdwood
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox