* [PATCH 1/2] move host drivers for VLB IDE controllers to staging/out
2010-02-02 17:27 [PATCH 0/2] atang update for 02/02/10 Bartlomiej Zolnierkiewicz
@ 2010-02-02 17:27 ` Bartlomiej Zolnierkiewicz
2010-02-02 18:00 ` Alan Cox
2010-02-02 17:27 ` [PATCH 2/2] ide: remove hwif_chipset_t type Bartlomiej Zolnierkiewicz
1 sibling, 1 reply; 7+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2010-02-02 17:27 UTC (permalink / raw)
To: linux-ide; +Cc: Bartlomiej Zolnierkiewicz, linux-kernel
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Subject: [PATCH] move host drivers for VLB IDE controllers to staging/out
- they are for really old hardware that nobody has any longer
- they all require 'magic' parameters to work
- many controllers are also supported by pata_legacy driver
so move them to staging/out and schedule for removal in 2.6.36
unless somebody steps in to work on them.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
drivers/ide/Kconfig | 72 -----
drivers/ide/Makefile | 7
drivers/ide/ali14xx.c | 249 ------------------
drivers/ide/dtc2278.c | 154 -----------
drivers/ide/ht6560b.c | 384 -----------------------------
drivers/ide/ide-4drives.c | 64 ----
drivers/ide/qd65xx.c | 446 ----------------------------------
drivers/ide/qd65xx.h | 144 ----------
drivers/ide/umc8672.c | 183 -------------
drivers/staging/Kconfig | 2
drivers/staging/Makefile | 1
drivers/staging/ide-vlb/Kconfig | 69 +++++
drivers/staging/ide-vlb/Makefile | 7
drivers/staging/ide-vlb/TODO | 5
drivers/staging/ide-vlb/ali14xx.c | 249 ++++++++++++++++++
drivers/staging/ide-vlb/dtc2278.c | 154 +++++++++++
drivers/staging/ide-vlb/ht6560b.c | 384 +++++++++++++++++++++++++++++
drivers/staging/ide-vlb/ide-4drives.c | 64 ++++
drivers/staging/ide-vlb/qd65xx.c | 446 ++++++++++++++++++++++++++++++++++
drivers/staging/ide-vlb/qd65xx.h | 144 ++++++++++
drivers/staging/ide-vlb/umc8672.c | 183 +++++++++++++
21 files changed, 1708 insertions(+), 1703 deletions(-)
Index: b/drivers/ide/Kconfig
===================================================================
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -826,78 +826,6 @@ config BLK_DEV_PALMCHIP_BK3710
Say Y here if you want to support the onchip IDE controller on the
TI DaVinci SoC
-# no isa -> no vlb
-if ISA && (ALPHA || X86 || MIPS)
-
-comment "Other IDE chipsets support"
-comment "Note: most of these also require special kernel boot parameters"
-
-config BLK_DEV_4DRIVES
- tristate "Generic 4 drives/port support"
- help
- Certain older chipsets, including the Tekram 690CD, use a single set
- of I/O ports at 0x1f0 to control up to four drives, instead of the
- customary two drives per port. Support for this can be enabled at
- runtime using the "ide-4drives.probe" kernel boot parameter if you
- say Y here.
-
-config BLK_DEV_ALI14XX
- tristate "ALI M14xx support"
- select IDE_TIMINGS
- select IDE_LEGACY
- help
- This driver is enabled at runtime using the "ali14xx.probe" kernel
- boot parameter. It enables support for the secondary IDE interface
- of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
- I/O speeds to be set as well.
- See the files <file:Documentation/ide/ide.txt> and
- <file:drivers/ide/legacy/ali14xx.c> for more info.
-
-config BLK_DEV_DTC2278
- tristate "DTC-2278 support"
- select IDE_XFER_MODE
- select IDE_LEGACY
- help
- This driver is enabled at runtime using the "dtc2278.probe" kernel
- boot parameter. It enables support for the secondary IDE interface
- of the DTC-2278 card, and permits faster I/O speeds to be set as
- well. See the <file:Documentation/ide/ide.txt> and
- <file:drivers/ide/legacy/dtc2278.c> files for more info.
-
-config BLK_DEV_HT6560B
- tristate "Holtek HT6560B support"
- select IDE_TIMINGS
- select IDE_LEGACY
- help
- This driver is enabled at runtime using the "ht6560b.probe" kernel
- boot parameter. It enables support for the secondary IDE interface
- of the Holtek card, and permits faster I/O speeds to be set as well.
- See the <file:Documentation/ide/ide.txt> and
- <file:drivers/ide/legacy/ht6560b.c> files for more info.
-
-config BLK_DEV_QD65XX
- tristate "QDI QD65xx support"
- select IDE_TIMINGS
- select IDE_LEGACY
- help
- This driver is enabled at runtime using the "qd65xx.probe" kernel
- boot parameter. It permits faster I/O speeds to be set. See the
- <file:Documentation/ide/ide.txt> and <file:drivers/ide/legacy/qd65xx.c>
- for more info.
-
-config BLK_DEV_UMC8672
- tristate "UMC-8672 support"
- select IDE_XFER_MODE
- select IDE_LEGACY
- help
- This driver is enabled at runtime using the "umc8672.probe" kernel
- boot parameter. It enables support for the secondary IDE interface
- of the UMC-8672, and permits faster I/O speeds to be set as well.
- See the files <file:Documentation/ide/ide.txt> and
- <file:drivers/ide/legacy/umc8672.c> for more info.
-
-endif
-
config BLK_DEV_IDEDMA
def_bool BLK_DEV_IDEDMA_SFF || \
BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
Index: b/drivers/ide/Makefile
===================================================================
--- a/drivers/ide/Makefile
+++ b/drivers/ide/Makefile
@@ -19,13 +19,6 @@ ide-core-$(CONFIG_IDE_LEGACY) += ide-le
obj-$(CONFIG_IDE) += ide-core.o
-obj-$(CONFIG_BLK_DEV_ALI14XX) += ali14xx.o
-obj-$(CONFIG_BLK_DEV_UMC8672) += umc8672.o
-obj-$(CONFIG_BLK_DEV_DTC2278) += dtc2278.o
-obj-$(CONFIG_BLK_DEV_HT6560B) += ht6560b.o
-obj-$(CONFIG_BLK_DEV_QD65XX) += qd65xx.o
-obj-$(CONFIG_BLK_DEV_4DRIVES) += ide-4drives.o
-
obj-$(CONFIG_BLK_DEV_GAYLE) += gayle.o
obj-$(CONFIG_BLK_DEV_FALCON_IDE) += falconide.o
obj-$(CONFIG_BLK_DEV_MAC_IDE) += macide.o
Index: b/drivers/ide/ali14xx.c
===================================================================
--- a/drivers/ide/ali14xx.c
+++ /dev/null
@@ -1,249 +0,0 @@
-/*
- * Copyright (C) 1996 Linus Torvalds & author (see below)
- */
-
-/*
- * ALI M14xx chipset EIDE controller
- *
- * Works for ALI M1439/1443/1445/1487/1489 chipsets.
- *
- * Adapted from code developed by derekn@vw.ece.cmu.edu. -ml
- * Derek's notes follow:
- *
- * I think the code should be pretty understandable,
- * but I'll be happy to (try to) answer questions.
- *
- * The critical part is in the setupDrive function. The initRegisters
- * function doesn't seem to be necessary, but the DOS driver does it, so
- * I threw it in.
- *
- * I've only tested this on my system, which only has one disk. I posted
- * it to comp.sys.linux.hardware, so maybe some other people will try it
- * out.
- *
- * Derek Noonburg (derekn@ece.cmu.edu)
- * 95-sep-26
- *
- * Update 96-jul-13:
- *
- * I've since upgraded to two disks and a CD-ROM, with no trouble, and
- * I've also heard from several others who have used it successfully.
- * This driver appears to work with both the 1443/1445 and the 1487/1489
- * chipsets. I've added support for PIO mode 4 for the 1487. This
- * seems to work just fine on the 1443 also, although I'm not sure it's
- * advertised as supporting mode 4. (I've been running a WDC AC21200 in
- * mode 4 for a while now with no trouble.) -Derek
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/ioport.h>
-#include <linux/blkdev.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-
-#define DRV_NAME "ali14xx"
-
-/* port addresses for auto-detection */
-#define ALI_NUM_PORTS 4
-static const int ports[ALI_NUM_PORTS] __initdata =
- { 0x074, 0x0f4, 0x034, 0x0e4 };
-
-/* register initialization data */
-typedef struct { u8 reg, data; } RegInitializer;
-
-static const RegInitializer initData[] __initdata = {
- {0x01, 0x0f}, {0x02, 0x00}, {0x03, 0x00}, {0x04, 0x00},
- {0x05, 0x00}, {0x06, 0x00}, {0x07, 0x2b}, {0x0a, 0x0f},
- {0x25, 0x00}, {0x26, 0x00}, {0x27, 0x00}, {0x28, 0x00},
- {0x29, 0x00}, {0x2a, 0x00}, {0x2f, 0x00}, {0x2b, 0x00},
- {0x2c, 0x00}, {0x2d, 0x00}, {0x2e, 0x00}, {0x30, 0x00},
- {0x31, 0x00}, {0x32, 0x00}, {0x33, 0x00}, {0x34, 0xff},
- {0x35, 0x03}, {0x00, 0x00}
-};
-
-/* timing parameter registers for each drive */
-static struct { u8 reg1, reg2, reg3, reg4; } regTab[4] = {
- {0x03, 0x26, 0x04, 0x27}, /* drive 0 */
- {0x05, 0x28, 0x06, 0x29}, /* drive 1 */
- {0x2b, 0x30, 0x2c, 0x31}, /* drive 2 */
- {0x2d, 0x32, 0x2e, 0x33}, /* drive 3 */
-};
-
-static int basePort; /* base port address */
-static int regPort; /* port for register number */
-static int dataPort; /* port for register data */
-static u8 regOn; /* output to base port to access registers */
-static u8 regOff; /* output to base port to close registers */
-
-/*------------------------------------------------------------------------*/
-
-/*
- * Read a controller register.
- */
-static inline u8 inReg(u8 reg)
-{
- outb_p(reg, regPort);
- return inb(dataPort);
-}
-
-/*
- * Write a controller register.
- */
-static void outReg(u8 data, u8 reg)
-{
- outb_p(reg, regPort);
- outb_p(data, dataPort);
-}
-
-static DEFINE_SPINLOCK(ali14xx_lock);
-
-/*
- * Set PIO mode for the specified drive.
- * This function computes timing parameters
- * and sets controller registers accordingly.
- */
-static void ali14xx_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- int driveNum;
- int time1, time2;
- u8 param1, param2, param3, param4;
- unsigned long flags;
- int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;
- const u8 pio = drive->pio_mode - XFER_PIO_0;
- const struct ata_timing *t = ata_timing_find_mode(XFER_PIO_0 + pio);
-
- /* calculate timing, according to PIO mode */
- time1 = ide_pio_cycle_time(drive, pio);
- time2 = t->active;
- param3 = param1 = (time2 * bus_speed + 999) / 1000;
- param4 = param2 = (time1 * bus_speed + 999) / 1000 - param1;
- if (pio < 3) {
- param3 += 8;
- param4 += 8;
- }
- printk(KERN_DEBUG "%s: PIO mode%d, t1=%dns, t2=%dns, cycles = %d+%d, %d+%d\n",
- drive->name, pio, time1, time2, param1, param2, param3, param4);
-
- /* stuff timing parameters into controller registers */
- driveNum = (drive->hwif->index << 1) + (drive->dn & 1);
- spin_lock_irqsave(&ali14xx_lock, flags);
- outb_p(regOn, basePort);
- outReg(param1, regTab[driveNum].reg1);
- outReg(param2, regTab[driveNum].reg2);
- outReg(param3, regTab[driveNum].reg3);
- outReg(param4, regTab[driveNum].reg4);
- outb_p(regOff, basePort);
- spin_unlock_irqrestore(&ali14xx_lock, flags);
-}
-
-/*
- * Auto-detect the IDE controller port.
- */
-static int __init findPort(void)
-{
- int i;
- u8 t;
- unsigned long flags;
-
- local_irq_save(flags);
- for (i = 0; i < ALI_NUM_PORTS; ++i) {
- basePort = ports[i];
- regOff = inb(basePort);
- for (regOn = 0x30; regOn <= 0x33; ++regOn) {
- outb_p(regOn, basePort);
- if (inb(basePort) == regOn) {
- regPort = basePort + 4;
- dataPort = basePort + 8;
- t = inReg(0) & 0xf0;
- outb_p(regOff, basePort);
- local_irq_restore(flags);
- if (t != 0x50)
- return 0;
- return 1; /* success */
- }
- }
- outb_p(regOff, basePort);
- }
- local_irq_restore(flags);
- return 0;
-}
-
-/*
- * Initialize controller registers with default values.
- */
-static int __init initRegisters(void)
-{
- const RegInitializer *p;
- u8 t;
- unsigned long flags;
-
- local_irq_save(flags);
- outb_p(regOn, basePort);
- for (p = initData; p->reg != 0; ++p)
- outReg(p->data, p->reg);
- outb_p(0x01, regPort);
- t = inb(regPort) & 0x01;
- outb_p(regOff, basePort);
- local_irq_restore(flags);
- return t;
-}
-
-static const struct ide_port_ops ali14xx_port_ops = {
- .set_pio_mode = ali14xx_set_pio_mode,
-};
-
-static const struct ide_port_info ali14xx_port_info = {
- .name = DRV_NAME,
- .chipset = ide_ali14xx,
- .port_ops = &ali14xx_port_ops,
- .host_flags = IDE_HFLAG_NO_DMA,
- .pio_mask = ATA_PIO4,
-};
-
-static int __init ali14xx_probe(void)
-{
- printk(KERN_DEBUG "ali14xx: base=0x%03x, regOn=0x%02x.\n",
- basePort, regOn);
-
- /* initialize controller registers */
- if (!initRegisters()) {
- printk(KERN_ERR "ali14xx: Chip initialization failed.\n");
- return 1;
- }
-
- return ide_legacy_device_add(&ali14xx_port_info, 0);
-}
-
-static int probe_ali14xx;
-
-module_param_named(probe, probe_ali14xx, bool, 0);
-MODULE_PARM_DESC(probe, "probe for ALI M14xx chipsets");
-
-static int __init ali14xx_init(void)
-{
- if (probe_ali14xx == 0)
- goto out;
-
- /* auto-detect IDE controller port */
- if (findPort()) {
- if (ali14xx_probe())
- return -ENODEV;
- return 0;
- }
- printk(KERN_ERR "ali14xx: not found.\n");
-out:
- return -ENODEV;
-}
-
-module_init(ali14xx_init);
-
-MODULE_AUTHOR("see local file");
-MODULE_DESCRIPTION("support of ALI 14XX IDE chipsets");
-MODULE_LICENSE("GPL");
Index: b/drivers/ide/dtc2278.c
===================================================================
--- a/drivers/ide/dtc2278.c
+++ /dev/null
@@ -1,154 +0,0 @@
-/*
- * Copyright (C) 1996 Linus Torvalds & author (see below)
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/ioport.h>
-#include <linux/blkdev.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-
-#define DRV_NAME "dtc2278"
-
-/*
- * Changing this #undef to #define may solve start up problems in some systems.
- */
-#undef ALWAYS_SET_DTC2278_PIO_MODE
-
-/*
- * From: andy@cercle.cts.com (Dyan Wile)
- *
- * Below is a patch for DTC-2278 - alike software-programmable controllers
- * The code enables the secondary IDE controller and the PIO4 (3?) timings on
- * the primary (EIDE). You may probably have to enable the 32-bit support to
- * get the full speed. You better get the disk interrupts disabled ( hdparm -u0
- * /dev/hd.. ) for the drives connected to the EIDE interface. (I get my
- * filesystem corrupted with -u1, but under heavy disk load only :-)
- *
- * This card is now forced to use the "serialize" feature,
- * and irq-unmasking is disallowed. If io_32bit is enabled,
- * it must be done for BOTH drives on each interface.
- *
- * This code was written for the DTC2278E, but might work with any of these:
- *
- * DTC2278S has only a single IDE interface.
- * DTC2278D has two IDE interfaces and is otherwise identical to the S version.
- * DTC2278E also has serial ports and a printer port
- * DTC2278EB: has onboard BIOS, and "works like a charm" -- Kent Bradford <kent@theory.caltech.edu>
- *
- * There may be a fourth controller type. The S and D versions use the
- * Winbond chip, and I think the E version does also.
- *
- */
-
-static void sub22 (char b, char c)
-{
- int i;
-
- for(i = 0; i < 3; ++i) {
- inb(0x3f6);
- outb_p(b,0xb0);
- inb(0x3f6);
- outb_p(c,0xb4);
- inb(0x3f6);
- if(inb(0xb4) == c) {
- outb_p(7,0xb0);
- inb(0x3f6);
- return; /* success */
- }
- }
-}
-
-static DEFINE_SPINLOCK(dtc2278_lock);
-
-static void dtc2278_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- unsigned long flags;
-
- if (drive->pio_mode >= XFER_PIO_3) {
- spin_lock_irqsave(&dtc2278_lock, flags);
- /*
- * This enables PIO mode4 (3?) on the first interface
- */
- sub22(1,0xc3);
- sub22(0,0xa0);
- spin_unlock_irqrestore(&dtc2278_lock, flags);
- } else {
- /* we don't know how to set it back again.. */
- /* Actually we do - there is a data sheet available for the
- Winbond but does anyone actually care */
- }
-}
-
-static const struct ide_port_ops dtc2278_port_ops = {
- .set_pio_mode = dtc2278_set_pio_mode,
-};
-
-static const struct ide_port_info dtc2278_port_info __initdata = {
- .name = DRV_NAME,
- .chipset = ide_dtc2278,
- .port_ops = &dtc2278_port_ops,
- .host_flags = IDE_HFLAG_SERIALIZE |
- IDE_HFLAG_NO_UNMASK_IRQS |
- IDE_HFLAG_IO_32BIT |
- /* disallow ->io_32bit changes */
- IDE_HFLAG_NO_IO_32BIT |
- IDE_HFLAG_NO_DMA |
- IDE_HFLAG_DTC2278,
- .pio_mask = ATA_PIO4,
-};
-
-static int __init dtc2278_probe(void)
-{
- unsigned long flags;
-
- local_irq_save(flags);
- /*
- * This enables the second interface
- */
- outb_p(4,0xb0);
- inb(0x3f6);
- outb_p(0x20,0xb4);
- inb(0x3f6);
-#ifdef ALWAYS_SET_DTC2278_PIO_MODE
- /*
- * This enables PIO mode4 (3?) on the first interface
- * and may solve start-up problems for some people.
- */
- sub22(1,0xc3);
- sub22(0,0xa0);
-#endif
- local_irq_restore(flags);
-
- return ide_legacy_device_add(&dtc2278_port_info, 0);
-}
-
-static int probe_dtc2278;
-
-module_param_named(probe, probe_dtc2278, bool, 0);
-MODULE_PARM_DESC(probe, "probe for DTC2278xx chipsets");
-
-static int __init dtc2278_init(void)
-{
- if (probe_dtc2278 == 0)
- return -ENODEV;
-
- if (dtc2278_probe()) {
- printk(KERN_ERR "dtc2278: ide interfaces already in use!\n");
- return -EBUSY;
- }
- return 0;
-}
-
-module_init(dtc2278_init);
-
-MODULE_AUTHOR("See Local File");
-MODULE_DESCRIPTION("support of DTC-2278 VLB IDE chipsets");
-MODULE_LICENSE("GPL");
Index: b/drivers/ide/ht6560b.c
===================================================================
--- a/drivers/ide/ht6560b.c
+++ /dev/null
@@ -1,384 +0,0 @@
-/*
- * Copyright (C) 1995-2000 Linus Torvalds & author (see below)
- */
-
-/*
- * HT-6560B EIDE-controller support
- * To activate controller support use kernel parameter "ide0=ht6560b".
- * Use hdparm utility to enable PIO mode support.
- *
- * Author: Mikko Ala-Fossi <maf@iki.fi>
- * Jan Evert van Grootheest <j.e.van.grootheest@caiway.nl>
- *
- * Try: http://www.maf.iki.fi/~maf/ht6560b/
- */
-
-#define DRV_NAME "ht6560b"
-#define HT6560B_VERSION "v0.08"
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/ioport.h>
-#include <linux/blkdev.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-
-/* #define DEBUG */ /* remove comments for DEBUG messages */
-
-/*
- * The special i/o-port that HT-6560B uses to configuration:
- * bit0 (0x01): "1" selects secondary interface
- * bit2 (0x04): "1" enables FIFO function
- * bit5 (0x20): "1" enables prefetched data read function (???)
- *
- * The special i/o-port that HT-6560A uses to configuration:
- * bit0 (0x01): "1" selects secondary interface
- * bit1 (0x02): "1" enables prefetched data read function
- * bit2 (0x04): "0" enables multi-master system (?)
- * bit3 (0x08): "1" 3 cycle time, "0" 2 cycle time (?)
- */
-#define HT_CONFIG_PORT 0x3e6
-
-static inline u8 HT_CONFIG(ide_drive_t *drive)
-{
- return ((unsigned long)ide_get_drivedata(drive) & 0xff00) >> 8;
-}
-
-/*
- * FIFO + PREFETCH (both a/b-model)
- */
-#define HT_CONFIG_DEFAULT 0x1c /* no prefetch */
-/* #define HT_CONFIG_DEFAULT 0x3c */ /* with prefetch */
-#define HT_SECONDARY_IF 0x01
-#define HT_PREFETCH_MODE 0x20
-
-/*
- * ht6560b Timing values:
- *
- * I reviewed some assembler source listings of htide drivers and found
- * out how they setup those cycle time interfacing values, as they at Holtek
- * call them. IDESETUP.COM that is supplied with the drivers figures out
- * optimal values and fetches those values to drivers. I found out that
- * they use Select register to fetch timings to the ide board right after
- * interface switching. After that it was quite easy to add code to
- * ht6560b.c.
- *
- * IDESETUP.COM gave me values 0x24, 0x45, 0xaa, 0xff that worked fine
- * for hda and hdc. But hdb needed higher values to work, so I guess
- * that sometimes it is necessary to give higher value than IDESETUP
- * gives. [see cmd640.c for an extreme example of this. -ml]
- *
- * Perhaps I should explain something about these timing values:
- * The higher nibble of value is the Recovery Time (rt) and the lower nibble
- * of the value is the Active Time (at). Minimum value 2 is the fastest and
- * the maximum value 15 is the slowest. Default values should be 15 for both.
- * So 0x24 means 2 for rt and 4 for at. Each of the drives should have
- * both values, and IDESETUP gives automatically rt=15 st=15 for CDROMs or
- * similar. If value is too small there will be all sorts of failures.
- *
- * Timing byte consists of
- * High nibble: Recovery Cycle Time (rt)
- * The valid values range from 2 to 15. The default is 15.
- *
- * Low nibble: Active Cycle Time (at)
- * The valid values range from 2 to 15. The default is 15.
- *
- * You can obtain optimized timing values by running Holtek IDESETUP.COM
- * for DOS. DOS drivers get their timing values from command line, where
- * the first value is the Recovery Time and the second value is the
- * Active Time for each drive. Smaller value gives higher speed.
- * In case of failures you should probably fall back to a higher value.
- */
-static inline u8 HT_TIMING(ide_drive_t *drive)
-{
- return (unsigned long)ide_get_drivedata(drive) & 0x00ff;
-}
-
-#define HT_TIMING_DEFAULT 0xff
-
-/*
- * This routine handles interface switching for the peculiar hardware design
- * on the F.G.I./Holtek HT-6560B VLB IDE interface.
- * The HT-6560B can only enable one IDE port at a time, and requires a
- * silly sequence (below) whenever we switch between primary and secondary.
- */
-
-/*
- * This routine is invoked from ide.c to prepare for access to a given drive.
- */
-static void ht6560b_dev_select(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- unsigned long flags;
- static u8 current_select = 0;
- static u8 current_timing = 0;
- u8 select, timing;
-
- local_irq_save(flags);
-
- select = HT_CONFIG(drive);
- timing = HT_TIMING(drive);
-
- /*
- * Need to enforce prefetch sometimes because otherwise
- * it'll hang (hard).
- */
- if (drive->media != ide_disk ||
- (drive->dev_flags & IDE_DFLAG_PRESENT) == 0)
- select |= HT_PREFETCH_MODE;
-
- if (select != current_select || timing != current_timing) {
- current_select = select;
- current_timing = timing;
- (void)inb(HT_CONFIG_PORT);
- (void)inb(HT_CONFIG_PORT);
- (void)inb(HT_CONFIG_PORT);
- (void)inb(HT_CONFIG_PORT);
- outb(select, HT_CONFIG_PORT);
- /*
- * Set timing for this drive:
- */
- outb(timing, hwif->io_ports.device_addr);
- (void)inb(hwif->io_ports.status_addr);
-#ifdef DEBUG
- printk("ht6560b: %s: select=%#x timing=%#x\n",
- drive->name, select, timing);
-#endif
- }
- local_irq_restore(flags);
-
- outb(drive->select | ATA_DEVICE_OBS, hwif->io_ports.device_addr);
-}
-
-/*
- * Autodetection and initialization of ht6560b
- */
-static int __init try_to_init_ht6560b(void)
-{
- u8 orig_value;
- int i;
-
- /* Autodetect ht6560b */
- if ((orig_value = inb(HT_CONFIG_PORT)) == 0xff)
- return 0;
-
- for (i=3;i>0;i--) {
- outb(0x00, HT_CONFIG_PORT);
- if (!( (~inb(HT_CONFIG_PORT)) & 0x3f )) {
- outb(orig_value, HT_CONFIG_PORT);
- return 0;
- }
- }
- outb(0x00, HT_CONFIG_PORT);
- if ((~inb(HT_CONFIG_PORT))& 0x3f) {
- outb(orig_value, HT_CONFIG_PORT);
- return 0;
- }
- /*
- * Ht6560b autodetected
- */
- outb(HT_CONFIG_DEFAULT, HT_CONFIG_PORT);
- outb(HT_TIMING_DEFAULT, 0x1f6); /* Select register */
- (void)inb(0x1f7); /* Status register */
-
- printk("ht6560b " HT6560B_VERSION
- ": chipset detected and initialized"
-#ifdef DEBUG
- " with debug enabled"
-#endif
- "\n"
- );
- return 1;
-}
-
-static u8 ht_pio2timings(ide_drive_t *drive, const u8 pio)
-{
- int active_time, recovery_time;
- int active_cycles, recovery_cycles;
- int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;
-
- if (pio) {
- unsigned int cycle_time;
- const struct ata_timing *t =
- ata_timing_find_mode(XFER_PIO_0 + pio);
-
- cycle_time = ide_pio_cycle_time(drive, pio);
-
- /*
- * Just like opti621.c we try to calculate the
- * actual cycle time for recovery and activity
- * according system bus speed.
- */
- active_time = t->active;
- recovery_time = cycle_time - active_time - t->setup;
- /*
- * Cycle times should be Vesa bus cycles
- */
- active_cycles = (active_time * bus_speed + 999) / 1000;
- recovery_cycles = (recovery_time * bus_speed + 999) / 1000;
- /*
- * Upper and lower limits
- */
- if (active_cycles < 2) active_cycles = 2;
- if (recovery_cycles < 2) recovery_cycles = 2;
- if (active_cycles > 15) active_cycles = 15;
- if (recovery_cycles > 15) recovery_cycles = 0; /* 0==16 */
-
-#ifdef DEBUG
- printk("ht6560b: drive %s setting pio=%d recovery=%d (%dns) active=%d (%dns)\n", drive->name, pio, recovery_cycles, recovery_time, active_cycles, active_time);
-#endif
-
- return (u8)((recovery_cycles << 4) | active_cycles);
- } else {
-
-#ifdef DEBUG
- printk("ht6560b: drive %s setting pio=0\n", drive->name);
-#endif
-
- return HT_TIMING_DEFAULT; /* default setting */
- }
-}
-
-static DEFINE_SPINLOCK(ht6560b_lock);
-
-/*
- * Enable/Disable so called prefetch mode
- */
-static void ht_set_prefetch(ide_drive_t *drive, u8 state)
-{
- unsigned long flags, config;
- int t = HT_PREFETCH_MODE << 8;
-
- spin_lock_irqsave(&ht6560b_lock, flags);
-
- config = (unsigned long)ide_get_drivedata(drive);
-
- /*
- * Prefetch mode and unmask irq seems to conflict
- */
- if (state) {
- config |= t; /* enable prefetch mode */
- drive->dev_flags |= IDE_DFLAG_NO_UNMASK;
- drive->dev_flags &= ~IDE_DFLAG_UNMASK;
- } else {
- config &= ~t; /* disable prefetch mode */
- drive->dev_flags &= ~IDE_DFLAG_NO_UNMASK;
- }
-
- ide_set_drivedata(drive, (void *)config);
-
- spin_unlock_irqrestore(&ht6560b_lock, flags);
-
-#ifdef DEBUG
- printk("ht6560b: drive %s prefetch mode %sabled\n", drive->name, (state ? "en" : "dis"));
-#endif
-}
-
-static void ht6560b_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- unsigned long flags, config;
- const u8 pio = drive->pio_mode - XFER_PIO_0;
- u8 timing;
-
- switch (pio) {
- case 8: /* set prefetch off */
- case 9: /* set prefetch on */
- ht_set_prefetch(drive, pio & 1);
- return;
- }
-
- timing = ht_pio2timings(drive, pio);
-
- spin_lock_irqsave(&ht6560b_lock, flags);
- config = (unsigned long)ide_get_drivedata(drive);
- config &= 0xff00;
- config |= timing;
- ide_set_drivedata(drive, (void *)config);
- spin_unlock_irqrestore(&ht6560b_lock, flags);
-
-#ifdef DEBUG
- printk("ht6560b: drive %s tuned to pio mode %#x timing=%#x\n", drive->name, pio, timing);
-#endif
-}
-
-static void __init ht6560b_init_dev(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- /* Setting default configurations for drives. */
- int t = (HT_CONFIG_DEFAULT << 8) | HT_TIMING_DEFAULT;
-
- if (hwif->channel)
- t |= (HT_SECONDARY_IF << 8);
-
- ide_set_drivedata(drive, (void *)t);
-}
-
-static int probe_ht6560b;
-
-module_param_named(probe, probe_ht6560b, bool, 0);
-MODULE_PARM_DESC(probe, "probe for HT6560B chipset");
-
-static const struct ide_tp_ops ht6560b_tp_ops = {
- .exec_command = ide_exec_command,
- .read_status = ide_read_status,
- .read_altstatus = ide_read_altstatus,
- .write_devctl = ide_write_devctl,
-
- .dev_select = ht6560b_dev_select,
- .tf_load = ide_tf_load,
- .tf_read = ide_tf_read,
-
- .input_data = ide_input_data,
- .output_data = ide_output_data,
-};
-
-static const struct ide_port_ops ht6560b_port_ops = {
- .init_dev = ht6560b_init_dev,
- .set_pio_mode = ht6560b_set_pio_mode,
-};
-
-static const struct ide_port_info ht6560b_port_info __initdata = {
- .name = DRV_NAME,
- .chipset = ide_ht6560b,
- .tp_ops = &ht6560b_tp_ops,
- .port_ops = &ht6560b_port_ops,
- .host_flags = IDE_HFLAG_SERIALIZE | /* is this needed? */
- IDE_HFLAG_NO_DMA |
- IDE_HFLAG_ABUSE_PREFETCH,
- .pio_mask = ATA_PIO4,
-};
-
-static int __init ht6560b_init(void)
-{
- if (probe_ht6560b == 0)
- return -ENODEV;
-
- if (!request_region(HT_CONFIG_PORT, 1, DRV_NAME)) {
- printk(KERN_NOTICE "%s: HT_CONFIG_PORT not found\n",
- __func__);
- return -ENODEV;
- }
-
- if (!try_to_init_ht6560b()) {
- printk(KERN_NOTICE "%s: HBA not found\n", __func__);
- goto release_region;
- }
-
- return ide_legacy_device_add(&ht6560b_port_info, 0);
-
-release_region:
- release_region(HT_CONFIG_PORT, 1);
- return -ENODEV;
-}
-
-module_init(ht6560b_init);
-
-MODULE_AUTHOR("See Local File");
-MODULE_DESCRIPTION("HT-6560B EIDE-controller support");
-MODULE_LICENSE("GPL");
Index: b/drivers/ide/ide-4drives.c
===================================================================
--- a/drivers/ide/ide-4drives.c
+++ /dev/null
@@ -1,64 +0,0 @@
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/ide.h>
-
-#define DRV_NAME "ide-4drives"
-
-static int probe_4drives;
-
-module_param_named(probe, probe_4drives, bool, 0);
-MODULE_PARM_DESC(probe, "probe for generic IDE chipset with 4 drives/port");
-
-static void ide_4drives_init_dev(ide_drive_t *drive)
-{
- if (drive->hwif->channel)
- drive->select ^= 0x20;
-}
-
-static const struct ide_port_ops ide_4drives_port_ops = {
- .init_dev = ide_4drives_init_dev,
-};
-
-static const struct ide_port_info ide_4drives_port_info = {
- .port_ops = &ide_4drives_port_ops,
- .host_flags = IDE_HFLAG_SERIALIZE | IDE_HFLAG_NO_DMA |
- IDE_HFLAG_4DRIVES,
- .chipset = ide_4drives,
-};
-
-static int __init ide_4drives_init(void)
-{
- unsigned long base = 0x1f0, ctl = 0x3f6;
- struct ide_hw hw, *hws[] = { &hw, &hw };
-
- if (probe_4drives == 0)
- return -ENODEV;
-
- if (!request_region(base, 8, DRV_NAME)) {
- printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n",
- DRV_NAME, base, base + 7);
- return -EBUSY;
- }
-
- if (!request_region(ctl, 1, DRV_NAME)) {
- printk(KERN_ERR "%s: I/O resource 0x%lX not free.\n",
- DRV_NAME, ctl);
- release_region(base, 8);
- return -EBUSY;
- }
-
- memset(&hw, 0, sizeof(hw));
-
- ide_std_init_ports(&hw, base, ctl);
- hw.irq = 14;
-
- return ide_host_add(&ide_4drives_port_info, hws, 2, NULL);
-}
-
-module_init(ide_4drives_init);
-
-MODULE_AUTHOR("Bartlomiej Zolnierkiewicz");
-MODULE_DESCRIPTION("generic IDE chipset with 4 drives/port support");
-MODULE_LICENSE("GPL");
Index: b/drivers/ide/qd65xx.c
===================================================================
--- a/drivers/ide/qd65xx.c
+++ /dev/null
@@ -1,446 +0,0 @@
-/*
- * Copyright (C) 1996-2001 Linus Torvalds & author (see below)
- */
-
-/*
- * Version 0.03 Cleaned auto-tune, added probe
- * Version 0.04 Added second channel tuning
- * Version 0.05 Enhanced tuning ; added qd6500 support
- * Version 0.06 Added dos driver's list
- * Version 0.07 Second channel bug fix
- *
- * QDI QD6500/QD6580 EIDE controller fast support
- *
- * To activate controller support, use "ide0=qd65xx"
- */
-
-/*
- * Rewritten from the work of Colten Edwards <pje120@cs.usask.ca> by
- * Samuel Thibault <samuel.thibault@ens-lyon.org>
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/ioport.h>
-#include <linux/blkdev.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-#include <asm/system.h>
-#include <asm/io.h>
-
-#define DRV_NAME "qd65xx"
-
-#include "qd65xx.h"
-
-/*
- * I/O ports are 0x30-0x31 (and 0x32-0x33 for qd6580)
- * or 0xb0-0xb1 (and 0xb2-0xb3 for qd6580)
- * -- qd6500 is a single IDE interface
- * -- qd6580 is a dual IDE interface
- *
- * More research on qd6580 being done by willmore@cig.mot.com (David)
- * More Information given by Petr Soucek (petr@ryston.cz)
- * http://www.ryston.cz/petr/vlb
- */
-
-/*
- * base: Timer1
- *
- *
- * base+0x01: Config (R/O)
- *
- * bit 0: ide baseport: 1 = 0x1f0 ; 0 = 0x170 (only useful for qd6500)
- * bit 1: qd65xx baseport: 1 = 0xb0 ; 0 = 0x30
- * bit 2: ID3: bus speed: 1 = <=33MHz ; 0 = >33MHz
- * bit 3: qd6500: 1 = disabled, 0 = enabled
- * qd6580: 1
- * upper nibble:
- * qd6500: 1100
- * qd6580: either 1010 or 0101
- *
- *
- * base+0x02: Timer2 (qd6580 only)
- *
- *
- * base+0x03: Control (qd6580 only)
- *
- * bits 0-3 must always be set 1
- * bit 4 must be set 1, but is set 0 by dos driver while measuring vlb clock
- * bit 0 : 1 = Only primary port enabled : channel 0 for hda, channel 1 for hdb
- * 0 = Primary and Secondary ports enabled : channel 0 for hda & hdb
- * channel 1 for hdc & hdd
- * bit 1 : 1 = only disks on primary port
- * 0 = disks & ATAPI devices on primary port
- * bit 2-4 : always 0
- * bit 5 : status, but of what ?
- * bit 6 : always set 1 by dos driver
- * bit 7 : set 1 for non-ATAPI devices on primary port
- * (maybe read-ahead and post-write buffer ?)
- */
-
-static int timings[4]={-1,-1,-1,-1}; /* stores current timing for each timer */
-
-/*
- * qd65xx_select:
- *
- * This routine is invoked to prepare for access to a given drive.
- */
-
-static void qd65xx_dev_select(ide_drive_t *drive)
-{
- u8 index = (( (QD_TIMREG(drive)) & 0x80 ) >> 7) |
- (QD_TIMREG(drive) & 0x02);
-
- if (timings[index] != QD_TIMING(drive))
- outb(timings[index] = QD_TIMING(drive), QD_TIMREG(drive));
-
- outb(drive->select | ATA_DEVICE_OBS, drive->hwif->io_ports.device_addr);
-}
-
-/*
- * qd6500_compute_timing
- *
- * computes the timing value where
- * lower nibble represents active time, in count of VLB clocks
- * upper nibble represents recovery time, in count of VLB clocks
- */
-
-static u8 qd6500_compute_timing (ide_hwif_t *hwif, int active_time, int recovery_time)
-{
- int clk = ide_vlb_clk ? ide_vlb_clk : 50;
- u8 act_cyc, rec_cyc;
-
- if (clk <= 33) {
- act_cyc = 9 - IDE_IN(active_time * clk / 1000 + 1, 2, 9);
- rec_cyc = 15 - IDE_IN(recovery_time * clk / 1000 + 1, 0, 15);
- } else {
- act_cyc = 8 - IDE_IN(active_time * clk / 1000 + 1, 1, 8);
- rec_cyc = 18 - IDE_IN(recovery_time * clk / 1000 + 1, 3, 18);
- }
-
- return (rec_cyc << 4) | 0x08 | act_cyc;
-}
-
-/*
- * qd6580_compute_timing
- *
- * idem for qd6580
- */
-
-static u8 qd6580_compute_timing (int active_time, int recovery_time)
-{
- int clk = ide_vlb_clk ? ide_vlb_clk : 50;
- u8 act_cyc, rec_cyc;
-
- act_cyc = 17 - IDE_IN(active_time * clk / 1000 + 1, 2, 17);
- rec_cyc = 15 - IDE_IN(recovery_time * clk / 1000 + 1, 2, 15);
-
- return (rec_cyc << 4) | act_cyc;
-}
-
-/*
- * qd_find_disk_type
- *
- * tries to find timing from dos driver's table
- */
-
-static int qd_find_disk_type (ide_drive_t *drive,
- int *active_time, int *recovery_time)
-{
- struct qd65xx_timing_s *p;
- char *m = (char *)&drive->id[ATA_ID_PROD];
- char model[ATA_ID_PROD_LEN];
-
- if (*m == 0)
- return 0;
-
- strncpy(model, m, ATA_ID_PROD_LEN);
- ide_fixstring(model, ATA_ID_PROD_LEN, 1); /* byte-swap */
-
- for (p = qd65xx_timing ; p->offset != -1 ; p++) {
- if (!strncmp(p->model, model+p->offset, 4)) {
- printk(KERN_DEBUG "%s: listed !\n", drive->name);
- *active_time = p->active;
- *recovery_time = p->recovery;
- return 1;
- }
- }
- return 0;
-}
-
-/*
- * qd_set_timing:
- *
- * records the timing
- */
-
-static void qd_set_timing (ide_drive_t *drive, u8 timing)
-{
- unsigned long data = (unsigned long)ide_get_drivedata(drive);
-
- data &= 0xff00;
- data |= timing;
- ide_set_drivedata(drive, (void *)data);
-
- printk(KERN_DEBUG "%s: %#x\n", drive->name, timing);
-}
-
-static void qd6500_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- u16 *id = drive->id;
- int active_time = 175;
- int recovery_time = 415; /* worst case values from the dos driver */
-
- /* FIXME: use drive->pio_mode value */
- if (!qd_find_disk_type(drive, &active_time, &recovery_time) &&
- (id[ATA_ID_OLD_PIO_MODES] & 0xff) && (id[ATA_ID_FIELD_VALID] & 2) &&
- id[ATA_ID_EIDE_PIO] >= 240) {
- printk(KERN_INFO "%s: PIO mode%d\n", drive->name,
- id[ATA_ID_OLD_PIO_MODES] & 0xff);
- active_time = 110;
- recovery_time = drive->id[ATA_ID_EIDE_PIO] - 120;
- }
-
- qd_set_timing(drive, qd6500_compute_timing(drive->hwif,
- active_time, recovery_time));
-}
-
-static void qd6580_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- const u8 pio = drive->pio_mode - XFER_PIO_0;
- const struct ata_timing *t = ata_timing_find_mode(XFER_PIO_0 + pio);
- unsigned int cycle_time;
- int active_time = 175;
- int recovery_time = 415; /* worst case values from the dos driver */
- u8 base = (hwif->config_data & 0xff00) >> 8;
-
- if (drive->id && !qd_find_disk_type(drive, &active_time, &recovery_time)) {
- cycle_time = ide_pio_cycle_time(drive, pio);
-
- switch (pio) {
- case 0: break;
- case 3:
- if (cycle_time >= 110) {
- active_time = 86;
- recovery_time = cycle_time - 102;
- } else
- printk(KERN_WARNING "%s: Strange recovery time !\n",drive->name);
- break;
- case 4:
- if (cycle_time >= 69) {
- active_time = 70;
- recovery_time = cycle_time - 61;
- } else
- printk(KERN_WARNING "%s: Strange recovery time !\n",drive->name);
- break;
- default:
- if (cycle_time >= 180) {
- active_time = 110;
- recovery_time = cycle_time - 120;
- } else {
- active_time = t->active;
- recovery_time = cycle_time - active_time;
- }
- }
- printk(KERN_INFO "%s: PIO mode%d\n", drive->name,pio);
- }
-
- if (!hwif->channel && drive->media != ide_disk) {
- outb(0x5f, QD_CONTROL_PORT);
- printk(KERN_WARNING "%s: ATAPI: disabled read-ahead FIFO "
- "and post-write buffer on %s.\n",
- drive->name, hwif->name);
- }
-
- qd_set_timing(drive, qd6580_compute_timing(active_time, recovery_time));
-}
-
-/*
- * qd_testreg
- *
- * tests if the given port is a register
- */
-
-static int __init qd_testreg(int port)
-{
- unsigned long flags;
- u8 savereg, readreg;
-
- local_irq_save(flags);
- savereg = inb_p(port);
- outb_p(QD_TESTVAL, port); /* safe value */
- readreg = inb_p(port);
- outb(savereg, port);
- local_irq_restore(flags);
-
- if (savereg == QD_TESTVAL) {
- printk(KERN_ERR "Outch ! the probe for qd65xx isn't reliable !\n");
- printk(KERN_ERR "Please contact maintainers to tell about your hardware\n");
- printk(KERN_ERR "Assuming qd65xx is not present.\n");
- return 1;
- }
-
- return (readreg != QD_TESTVAL);
-}
-
-static void __init qd6500_init_dev(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- u8 base = (hwif->config_data & 0xff00) >> 8;
- u8 config = QD_CONFIG(hwif);
-
- ide_set_drivedata(drive, (void *)QD6500_DEF_DATA);
-}
-
-static void __init qd6580_init_dev(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- u16 t1, t2;
- u8 base = (hwif->config_data & 0xff00) >> 8;
- u8 config = QD_CONFIG(hwif);
-
- if (hwif->host_flags & IDE_HFLAG_SINGLE) {
- t1 = QD6580_DEF_DATA;
- t2 = QD6580_DEF_DATA2;
- } else
- t2 = t1 = hwif->channel ? QD6580_DEF_DATA2 : QD6580_DEF_DATA;
-
- ide_set_drivedata(drive, (void *)((drive->dn & 1) ? t2 : t1));
-}
-
-static const struct ide_tp_ops qd65xx_tp_ops = {
- .exec_command = ide_exec_command,
- .read_status = ide_read_status,
- .read_altstatus = ide_read_altstatus,
- .write_devctl = ide_write_devctl,
-
- .dev_select = qd65xx_dev_select,
- .tf_load = ide_tf_load,
- .tf_read = ide_tf_read,
-
- .input_data = ide_input_data,
- .output_data = ide_output_data,
-};
-
-static const struct ide_port_ops qd6500_port_ops = {
- .init_dev = qd6500_init_dev,
- .set_pio_mode = qd6500_set_pio_mode,
-};
-
-static const struct ide_port_ops qd6580_port_ops = {
- .init_dev = qd6580_init_dev,
- .set_pio_mode = qd6580_set_pio_mode,
-};
-
-static const struct ide_port_info qd65xx_port_info __initdata = {
- .name = DRV_NAME,
- .tp_ops = &qd65xx_tp_ops,
- .chipset = ide_qd65xx,
- .host_flags = IDE_HFLAG_IO_32BIT |
- IDE_HFLAG_NO_DMA,
- .pio_mask = ATA_PIO4,
-};
-
-/*
- * qd_probe:
- *
- * looks at the specified baseport, and if qd found, registers & initialises it
- * return 1 if another qd may be probed
- */
-
-static int __init qd_probe(int base)
-{
- int rc;
- u8 config, unit, control;
- struct ide_port_info d = qd65xx_port_info;
-
- config = inb(QD_CONFIG_PORT);
-
- if (! ((config & QD_CONFIG_BASEPORT) >> 1 == (base == 0xb0)) )
- return -ENODEV;
-
- unit = ! (config & QD_CONFIG_IDE_BASEPORT);
-
- if (unit)
- d.host_flags |= IDE_HFLAG_QD_2ND_PORT;
-
- switch (config & 0xf0) {
- case QD_CONFIG_QD6500:
- if (qd_testreg(base))
- return -ENODEV; /* bad register */
-
- if (config & QD_CONFIG_DISABLED) {
- printk(KERN_WARNING "qd6500 is disabled !\n");
- return -ENODEV;
- }
-
- printk(KERN_NOTICE "qd6500 at %#x\n", base);
- printk(KERN_DEBUG "qd6500: config=%#x, ID3=%u\n",
- config, QD_ID3);
-
- d.port_ops = &qd6500_port_ops;
- d.host_flags |= IDE_HFLAG_SINGLE;
- break;
- case QD_CONFIG_QD6580_A:
- case QD_CONFIG_QD6580_B:
- if (qd_testreg(base) || qd_testreg(base + 0x02))
- return -ENODEV; /* bad registers */
-
- control = inb(QD_CONTROL_PORT);
-
- printk(KERN_NOTICE "qd6580 at %#x\n", base);
- printk(KERN_DEBUG "qd6580: config=%#x, control=%#x, ID3=%u\n",
- config, control, QD_ID3);
-
- outb(QD_DEF_CONTR, QD_CONTROL_PORT);
-
- d.port_ops = &qd6580_port_ops;
- if (control & QD_CONTR_SEC_DISABLED)
- d.host_flags |= IDE_HFLAG_SINGLE;
-
- printk(KERN_INFO "qd6580: %s IDE board\n",
- (control & QD_CONTR_SEC_DISABLED) ? "single" : "dual");
- break;
- default:
- return -ENODEV;
- }
-
- rc = ide_legacy_device_add(&d, (base << 8) | config);
-
- if (d.host_flags & IDE_HFLAG_SINGLE)
- return (rc == 0) ? 1 : rc;
-
- return rc;
-}
-
-static int probe_qd65xx;
-
-module_param_named(probe, probe_qd65xx, bool, 0);
-MODULE_PARM_DESC(probe, "probe for QD65xx chipsets");
-
-static int __init qd65xx_init(void)
-{
- int rc1, rc2 = -ENODEV;
-
- if (probe_qd65xx == 0)
- return -ENODEV;
-
- rc1 = qd_probe(0x30);
- if (rc1)
- rc2 = qd_probe(0xb0);
-
- if (rc1 < 0 && rc2 < 0)
- return -ENODEV;
-
- return 0;
-}
-
-module_init(qd65xx_init);
-
-MODULE_AUTHOR("Samuel Thibault");
-MODULE_DESCRIPTION("support of qd65xx vlb ide chipset");
-MODULE_LICENSE("GPL");
Index: b/drivers/ide/qd65xx.h
===================================================================
--- a/drivers/ide/qd65xx.h
+++ /dev/null
@@ -1,144 +0,0 @@
-/*
- * Copyright (c) 2000 Linus Torvalds & authors
- */
-
-/*
- * Authors: Petr Soucek <petr@ryston.cz>
- * Samuel Thibault <samuel.thibault@ens-lyon.org>
- */
-
-/* truncates a in [b,c] */
-#define IDE_IN(a,b,c) ( ((a)<(b)) ? (b) : ( (a)>(c) ? (c) : (a)) )
-
-#define IDE_IMPLY(a,b) ((!(a)) || (b))
-
-#define QD_TIM1_PORT (base)
-#define QD_CONFIG_PORT (base+0x01)
-#define QD_TIM2_PORT (base+0x02)
-#define QD_CONTROL_PORT (base+0x03)
-
-#define QD_CONFIG_IDE_BASEPORT 0x01
-#define QD_CONFIG_BASEPORT 0x02
-#define QD_CONFIG_ID3 0x04
-#define QD_CONFIG_DISABLED 0x08
-#define QD_CONFIG_QD6500 0xc0
-#define QD_CONFIG_QD6580_A 0xa0
-#define QD_CONFIG_QD6580_B 0x50
-
-#define QD_CONTR_SEC_DISABLED 0x01
-
-#define QD_ID3 ((config & QD_CONFIG_ID3)!=0)
-
-#define QD_CONFIG(hwif) ((hwif)->config_data & 0x00ff)
-
-static inline u8 QD_TIMING(ide_drive_t *drive)
-{
- return (unsigned long)ide_get_drivedata(drive) & 0x00ff;
-}
-
-static inline u8 QD_TIMREG(ide_drive_t *drive)
-{
- return ((unsigned long)ide_get_drivedata(drive) & 0xff00) >> 8;
-}
-
-#define QD6500_DEF_DATA ((QD_TIM1_PORT<<8) | (QD_ID3 ? 0x0c : 0x08))
-#define QD6580_DEF_DATA ((QD_TIM1_PORT<<8) | (QD_ID3 ? 0x0a : 0x00))
-#define QD6580_DEF_DATA2 ((QD_TIM2_PORT<<8) | (QD_ID3 ? 0x0a : 0x00))
-#define QD_DEF_CONTR (0x40 | ((control & 0x02) ? 0x9f : 0x1f))
-
-#define QD_TESTVAL 0x19 /* safe value */
-
-/* Drive specific timing taken from DOS driver v3.7 */
-
-static struct qd65xx_timing_s {
- s8 offset; /* ofset from the beginning of Model Number" */
- char model[4]; /* 4 chars from Model number, no conversion */
- s16 active; /* active time */
- s16 recovery; /* recovery time */
-} qd65xx_timing [] = {
- { 30, "2040", 110, 225 }, /* Conner CP30204 */
- { 30, "2045", 135, 225 }, /* Conner CP30254 */
- { 30, "1040", 155, 325 }, /* Conner CP30104 */
- { 30, "1047", 135, 265 }, /* Conner CP30174 */
- { 30, "5344", 135, 225 }, /* Conner CP3544 */
- { 30, "01 4", 175, 405 }, /* Conner CP-3104 */
- { 27, "C030", 175, 375 }, /* Conner CP3000 */
- { 8, "PL42", 110, 295 }, /* Quantum LP240 */
- { 8, "PL21", 110, 315 }, /* Quantum LP120 */
- { 8, "PL25", 175, 385 }, /* Quantum LP52 */
- { 4, "PA24", 110, 285 }, /* WD Piranha SP4200 */
- { 6, "2200", 110, 260 }, /* WD Caviar AC2200 */
- { 6, "3204", 110, 235 }, /* WD Caviar AC2340 */
- { 6, "1202", 110, 265 }, /* WD Caviar AC2120 */
- { 0, "DS3-", 135, 315 }, /* Teac SD340 */
- { 8, "KM32", 175, 355 }, /* Toshiba MK234 */
- { 2, "53A1", 175, 355 }, /* Seagate ST351A */
- { 2, "4108", 175, 295 }, /* Seagate ST1480A */
- { 2, "1344", 175, 335 }, /* Seagate ST3144A */
- { 6, "7 12", 110, 225 }, /* Maxtor 7213A */
- { 30, "02F4", 145, 295 }, /* Conner 3204F */
- { 2, "1302", 175, 335 }, /* Seagate ST3120A */
- { 2, "2334", 145, 265 }, /* Seagate ST3243A */
- { 2, "2338", 145, 275 }, /* Seagate ST3283A */
- { 2, "3309", 145, 275 }, /* Seagate ST3390A */
- { 2, "5305", 145, 275 }, /* Seagate ST3550A */
- { 2, "4100", 175, 295 }, /* Seagate ST1400A */
- { 2, "4110", 175, 295 }, /* Seagate ST1401A */
- { 2, "6300", 135, 265 }, /* Seagate ST3600A */
- { 2, "5300", 135, 265 }, /* Seagate ST3500A */
- { 6, "7 31", 135, 225 }, /* Maxtor 7131 AT */
- { 6, "7 43", 115, 265 }, /* Maxtor 7345 AT */
- { 6, "7 42", 110, 255 }, /* Maxtor 7245 AT */
- { 6, "3 04", 135, 265 }, /* Maxtor 340 AT */
- { 6, "61 0", 135, 285 }, /* WD AC160 */
- { 6, "1107", 135, 235 }, /* WD AC1170 */
- { 6, "2101", 110, 220 }, /* WD AC1210 */
- { 6, "4202", 135, 245 }, /* WD AC2420 */
- { 6, "41 0", 175, 355 }, /* WD Caviar 140 */
- { 6, "82 0", 175, 355 }, /* WD Caviar 280 */
- { 8, "PL01", 175, 375 }, /* Quantum LP105 */
- { 8, "PL25", 110, 295 }, /* Quantum LP525 */
- { 10, "4S 2", 175, 385 }, /* Quantum ELS42 */
- { 10, "8S 5", 175, 385 }, /* Quantum ELS85 */
- { 10, "1S72", 175, 385 }, /* Quantum ELS127 */
- { 10, "1S07", 175, 385 }, /* Quantum ELS170 */
- { 8, "ZE42", 135, 295 }, /* Quantum EZ240 */
- { 8, "ZE21", 175, 385 }, /* Quantum EZ127 */
- { 8, "ZE58", 175, 385 }, /* Quantum EZ85 */
- { 8, "ZE24", 175, 385 }, /* Quantum EZ42 */
- { 27, "C036", 155, 325 }, /* Conner CP30064 */
- { 27, "C038", 155, 325 }, /* Conner CP30084 */
- { 6, "2205", 110, 255 }, /* WDC AC2250 */
- { 2, " CHA", 140, 415 }, /* WDC AH series; WDC AH260, WDC */
- { 2, " CLA", 140, 415 }, /* WDC AL series: WDC AL2120, 2170, */
- { 4, "UC41", 140, 415 }, /* WDC CU140 */
- { 6, "1207", 130, 275 }, /* WDC AC2170 */
- { 6, "2107", 130, 275 }, /* WDC AC1270 */
- { 6, "5204", 130, 275 }, /* WDC AC2540 */
- { 30, "3004", 110, 235 }, /* Conner CP30340 */
- { 30, "0345", 135, 255 }, /* Conner CP30544 */
- { 12, "12A3", 175, 320 }, /* MAXTOR LXT-213A */
- { 12, "43A0", 145, 240 }, /* MAXTOR LXT-340A */
- { 6, "7 21", 180, 290 }, /* Maxtor 7120 AT */
- { 6, "7 71", 135, 240 }, /* Maxtor 7170 AT */
- { 12, "45\0000", 110, 205 }, /* MAXTOR MXT-540 */
- { 8, "PL11", 180, 290 }, /* QUANTUM LP110A */
- { 8, "OG21", 150, 275 }, /* QUANTUM GO120 */
- { 12, "42A5", 175, 320 }, /* MAXTOR LXT-245A */
- { 2, "2309", 175, 295 }, /* ST3290A */
- { 2, "3358", 180, 310 }, /* ST3385A */
- { 2, "6355", 180, 310 }, /* ST3655A */
- { 2, "1900", 175, 270 }, /* ST9100A */
- { 2, "1954", 175, 270 }, /* ST9145A */
- { 2, "1909", 175, 270 }, /* ST9190AG */
- { 2, "2953", 175, 270 }, /* ST9235A */
- { 2, "1359", 175, 270 }, /* ST3195A */
- { 24, "3R11", 175, 290 }, /* ALPS ELECTRIC Co.,LTD, DR311C */
- { 0, "2M26", 175, 215 }, /* M262XT-0Ah */
- { 4, "2253", 175, 300 }, /* HP C2235A */
- { 4, "-32A", 145, 245 }, /* H3133-A2 */
- { 30, "0326", 150, 270 }, /* Samsung Electronics 120MB */
- { 30, "3044", 110, 195 }, /* Conner CFA340A */
- { 30, "43A0", 110, 195 }, /* Conner CFA340A */
- { -1, " ", 175, 415 } /* unknown disk name */
-};
Index: b/drivers/ide/umc8672.c
===================================================================
--- a/drivers/ide/umc8672.c
+++ /dev/null
@@ -1,183 +0,0 @@
-/*
- * Copyright (C) 1995-1996 Linus Torvalds & author (see below)
- */
-
-/*
- * Principal Author/Maintainer: PODIEN@hml2.atlas.de (Wolfram Podien)
- *
- * This file provides support for the advanced features
- * of the UMC 8672 IDE interface.
- *
- * Version 0.01 Initial version, hacked out of ide.c,
- * and #include'd rather than compiled separately.
- * This will get cleaned up in a subsequent release.
- *
- * Version 0.02 now configs/compiles separate from ide.c -ml
- * Version 0.03 enhanced auto-tune, fix display bug
- * Version 0.05 replace sti() with restore_flags() -ml
- * add detection of possible race condition -ml
- */
-
-/*
- * VLB Controller Support from
- * Wolfram Podien
- * Rohoefe 3
- * D28832 Achim
- * Germany
- *
- * To enable UMC8672 support there must a lilo line like
- * append="ide0=umc8672"...
- * To set the speed according to the abilities of the hardware there must be a
- * line like
- * #define UMC_DRIVE0 11
- * in the beginning of the driver, which sets the speed of drive 0 to 11 (there
- * are some lines present). 0 - 11 are allowed speed values. These values are
- * the results from the DOS speed test program supplied from UMC. 11 is the
- * highest speed (about PIO mode 3)
- */
-#define REALLY_SLOW_IO /* some systems can safely undef this */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/ioport.h>
-#include <linux/blkdev.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-
-#define DRV_NAME "umc8672"
-
-/*
- * Default speeds. These can be changed with "auto-tune" and/or hdparm.
- */
-#define UMC_DRIVE0 1 /* DOS measured drive speeds */
-#define UMC_DRIVE1 1 /* 0 to 11 allowed */
-#define UMC_DRIVE2 1 /* 11 = Fastest Speed */
-#define UMC_DRIVE3 1 /* In case of crash reduce speed */
-
-static u8 current_speeds[4] = {UMC_DRIVE0, UMC_DRIVE1, UMC_DRIVE2, UMC_DRIVE3};
-static const u8 pio_to_umc [5] = {0, 3, 7, 10, 11}; /* rough guesses */
-
-/* 0 1 2 3 4 5 6 7 8 9 10 11 */
-static const u8 speedtab [3][12] = {
- {0x0f, 0x0b, 0x02, 0x02, 0x02, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x1},
- {0x03, 0x02, 0x02, 0x02, 0x02, 0x02, 0x01, 0x01, 0x01, 0x01, 0x01, 0x1},
- {0xff, 0xcb, 0xc0, 0x58, 0x36, 0x33, 0x23, 0x22, 0x21, 0x11, 0x10, 0x0}
-};
-
-static void out_umc(char port, char wert)
-{
- outb_p(port, 0x108);
- outb_p(wert, 0x109);
-}
-
-static inline u8 in_umc(char port)
-{
- outb_p(port, 0x108);
- return inb_p(0x109);
-}
-
-static void umc_set_speeds(u8 speeds[])
-{
- int i, tmp;
-
- outb_p(0x5A, 0x108); /* enable umc */
-
- out_umc(0xd7, (speedtab[0][speeds[2]] | (speedtab[0][speeds[3]]<<4)));
- out_umc(0xd6, (speedtab[0][speeds[0]] | (speedtab[0][speeds[1]]<<4)));
- tmp = 0;
- for (i = 3; i >= 0; i--)
- tmp = (tmp << 2) | speedtab[1][speeds[i]];
- out_umc(0xdc, tmp);
- for (i = 0; i < 4; i++) {
- out_umc(0xd0 + i, speedtab[2][speeds[i]]);
- out_umc(0xd8 + i, speedtab[2][speeds[i]]);
- }
- outb_p(0xa5, 0x108); /* disable umc */
-
- printk("umc8672: drive speeds [0 to 11]: %d %d %d %d\n",
- speeds[0], speeds[1], speeds[2], speeds[3]);
-}
-
-static void umc_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- ide_hwif_t *mate = hwif->mate;
- unsigned long uninitialized_var(flags);
- const u8 pio = drive->pio_mode - XFER_PIO_0;
-
- printk("%s: setting umc8672 to PIO mode%d (speed %d)\n",
- drive->name, pio, pio_to_umc[pio]);
- if (mate)
- spin_lock_irqsave(&mate->lock, flags);
- if (mate && mate->handler) {
- printk(KERN_ERR "umc8672: other interface is busy: exiting tune_umc()\n");
- } else {
- current_speeds[drive->name[2] - 'a'] = pio_to_umc[pio];
- umc_set_speeds(current_speeds);
- }
- if (mate)
- spin_unlock_irqrestore(&mate->lock, flags);
-}
-
-static const struct ide_port_ops umc8672_port_ops = {
- .set_pio_mode = umc_set_pio_mode,
-};
-
-static const struct ide_port_info umc8672_port_info __initdata = {
- .name = DRV_NAME,
- .chipset = ide_umc8672,
- .port_ops = &umc8672_port_ops,
- .host_flags = IDE_HFLAG_NO_DMA,
- .pio_mask = ATA_PIO4,
-};
-
-static int __init umc8672_probe(void)
-{
- unsigned long flags;
-
- if (!request_region(0x108, 2, "umc8672")) {
- printk(KERN_ERR "umc8672: ports 0x108-0x109 already in use.\n");
- return 1;
- }
- local_irq_save(flags);
- outb_p(0x5A, 0x108); /* enable umc */
- if (in_umc (0xd5) != 0xa0) {
- local_irq_restore(flags);
- printk(KERN_ERR "umc8672: not found\n");
- release_region(0x108, 2);
- return 1;
- }
- outb_p(0xa5, 0x108); /* disable umc */
-
- umc_set_speeds(current_speeds);
- local_irq_restore(flags);
-
- return ide_legacy_device_add(&umc8672_port_info, 0);
-}
-
-static int probe_umc8672;
-
-module_param_named(probe, probe_umc8672, bool, 0);
-MODULE_PARM_DESC(probe, "probe for UMC8672 chipset");
-
-static int __init umc8672_init(void)
-{
- if (probe_umc8672 == 0)
- goto out;
-
- if (umc8672_probe() == 0)
- return 0;
-out:
- return -ENODEV;
-}
-
-module_init(umc8672_init);
-
-MODULE_AUTHOR("Wolfram Podien");
-MODULE_DESCRIPTION("Support for UMC 8672 IDE chipset");
-MODULE_LICENSE("GPL");
Index: b/drivers/staging/Kconfig
===================================================================
--- a/drivers/staging/Kconfig
+++ b/drivers/staging/Kconfig
@@ -125,5 +125,7 @@ source "drivers/staging/sep/Kconfig"
source "drivers/staging/iio/Kconfig"
+source "drivers/staging/ide-vlb/Kconfig"
+
endif # !STAGING_EXCLUDE_BUILD
endif # STAGING
Index: b/drivers/staging/Makefile
===================================================================
--- a/drivers/staging/Makefile
+++ b/drivers/staging/Makefile
@@ -44,3 +44,4 @@ obj-$(CONFIG_VME_BUS) += vme/
obj-$(CONFIG_RAR_REGISTER) += rar/
obj-$(CONFIG_DX_SEP) += sep/
obj-$(CONFIG_IIO) += iio/
+obj-$(CONFIG_IDE) += ide-vlb/
Index: b/drivers/staging/ide-vlb/Kconfig
===================================================================
--- /dev/null
+++ b/drivers/staging/ide-vlb/Kconfig
@@ -0,0 +1,69 @@
+
+# no isa -> no vlb
+if ISA && (ALPHA || X86 || MIPS) && IDE
+
+config IDE_VLB_4DRIVES
+ tristate "Generic 4 drives/port ISA/VLB IDE support"
+ help
+ Certain older chipsets, including the Tekram 690CD, use a single set
+ of I/O ports at 0x1f0 to control up to four drives, instead of the
+ customary two drives per port. Support for this can be enabled at
+ runtime using the "ide-4drives.probe" kernel boot parameter if you
+ say Y here.
+
+config IDE_VLB_ALI14XX
+ tristate "ALI M14xx VLB IDE support"
+ select IDE_TIMINGS
+ select IDE_LEGACY
+ help
+ This driver is enabled at runtime using the "ali14xx.probe" kernel
+ boot parameter. It enables support for the secondary IDE interface
+ of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
+ I/O speeds to be set as well.
+ See the files <file:Documentation/ide/ide.txt> and
+ <file:drivers/ide/legacy/ali14xx.c> for more info.
+
+config IDE_VLB_DTC2278
+ tristate "DTC-2278 VLB IDE support"
+ select IDE_XFER_MODE
+ select IDE_LEGACY
+ help
+ This driver is enabled at runtime using the "dtc2278.probe" kernel
+ boot parameter. It enables support for the secondary IDE interface
+ of the DTC-2278 card, and permits faster I/O speeds to be set as
+ well. See the <file:Documentation/ide/ide.txt> and
+ <file:drivers/ide/legacy/dtc2278.c> files for more info.
+
+config IDE_VLB_HT6560B
+ tristate "Holtek HT6560B VLB IDE support"
+ select IDE_TIMINGS
+ select IDE_LEGACY
+ help
+ This driver is enabled at runtime using the "ht6560b.probe" kernel
+ boot parameter. It enables support for the secondary IDE interface
+ of the Holtek card, and permits faster I/O speeds to be set as well.
+ See the <file:Documentation/ide/ide.txt> and
+ <file:drivers/ide/legacy/ht6560b.c> files for more info.
+
+config IDE_VLB_QD65XX
+ tristate "QDI QD65xx VLB IDE support"
+ select IDE_TIMINGS
+ select IDE_LEGACY
+ help
+ This driver is enabled at runtime using the "qd65xx.probe" kernel
+ boot parameter. It permits faster I/O speeds to be set. See the
+ <file:Documentation/ide/ide.txt> and <file:drivers/ide/legacy/qd65xx.c>
+ for more info.
+
+config IDE_VLB_UMC8672
+ tristate "UMC-8672 VLB IDE support"
+ select IDE_XFER_MODE
+ select IDE_LEGACY
+ help
+ This driver is enabled at runtime using the "umc8672.probe" kernel
+ boot parameter. It enables support for the secondary IDE interface
+ of the UMC-8672, and permits faster I/O speeds to be set as well.
+ See the files <file:Documentation/ide/ide.txt> and
+ <file:drivers/ide/legacy/umc8672.c> for more info.
+
+endif
Index: b/drivers/staging/ide-vlb/Makefile
===================================================================
--- /dev/null
+++ b/drivers/staging/ide-vlb/Makefile
@@ -0,0 +1,7 @@
+
+obj-$(CONFIG_IDE_VLB_ALI14XX) += ali14xx.o
+obj-$(CONFIG_IDE_VLB_UMC8672) += umc8672.o
+obj-$(CONFIG_IDE_VLB_DTC2278) += dtc2278.o
+obj-$(CONFIG_IDE_VLB_HT6560B) += ht6560b.o
+obj-$(CONFIG_IDE_VLB_QD65XX) += qd65xx.o
+obj-$(CONFIG_IDE_VLB_4DRIVES) += ide-4drives.o
Index: b/drivers/staging/ide-vlb/TODO
===================================================================
--- /dev/null
+++ b/drivers/staging/ide-vlb/TODO
@@ -0,0 +1,5 @@
+TODO:
+ - add missing hardware support to drivers/ata/pata_legacy driver
+ and then maintain it to ensure that it continues to work. Having
+ the hardware for this is pretty much a requirement. If this does
+ not happen, the code will be removed in the 2.6.36 kernel release.
Index: b/drivers/staging/ide-vlb/ali14xx.c
===================================================================
--- /dev/null
+++ b/drivers/staging/ide-vlb/ali14xx.c
@@ -0,0 +1,249 @@
+/*
+ * Copyright (C) 1996 Linus Torvalds & author (see below)
+ */
+
+/*
+ * ALI M14xx chipset EIDE controller
+ *
+ * Works for ALI M1439/1443/1445/1487/1489 chipsets.
+ *
+ * Adapted from code developed by derekn@vw.ece.cmu.edu. -ml
+ * Derek's notes follow:
+ *
+ * I think the code should be pretty understandable,
+ * but I'll be happy to (try to) answer questions.
+ *
+ * The critical part is in the setupDrive function. The initRegisters
+ * function doesn't seem to be necessary, but the DOS driver does it, so
+ * I threw it in.
+ *
+ * I've only tested this on my system, which only has one disk. I posted
+ * it to comp.sys.linux.hardware, so maybe some other people will try it
+ * out.
+ *
+ * Derek Noonburg (derekn@ece.cmu.edu)
+ * 95-sep-26
+ *
+ * Update 96-jul-13:
+ *
+ * I've since upgraded to two disks and a CD-ROM, with no trouble, and
+ * I've also heard from several others who have used it successfully.
+ * This driver appears to work with both the 1443/1445 and the 1487/1489
+ * chipsets. I've added support for PIO mode 4 for the 1487. This
+ * seems to work just fine on the 1443 also, although I'm not sure it's
+ * advertised as supporting mode 4. (I've been running a WDC AC21200 in
+ * mode 4 for a while now with no trouble.) -Derek
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/ioport.h>
+#include <linux/blkdev.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+
+#define DRV_NAME "ali14xx"
+
+/* port addresses for auto-detection */
+#define ALI_NUM_PORTS 4
+static const int ports[ALI_NUM_PORTS] __initdata =
+ { 0x074, 0x0f4, 0x034, 0x0e4 };
+
+/* register initialization data */
+typedef struct { u8 reg, data; } RegInitializer;
+
+static const RegInitializer initData[] __initdata = {
+ {0x01, 0x0f}, {0x02, 0x00}, {0x03, 0x00}, {0x04, 0x00},
+ {0x05, 0x00}, {0x06, 0x00}, {0x07, 0x2b}, {0x0a, 0x0f},
+ {0x25, 0x00}, {0x26, 0x00}, {0x27, 0x00}, {0x28, 0x00},
+ {0x29, 0x00}, {0x2a, 0x00}, {0x2f, 0x00}, {0x2b, 0x00},
+ {0x2c, 0x00}, {0x2d, 0x00}, {0x2e, 0x00}, {0x30, 0x00},
+ {0x31, 0x00}, {0x32, 0x00}, {0x33, 0x00}, {0x34, 0xff},
+ {0x35, 0x03}, {0x00, 0x00}
+};
+
+/* timing parameter registers for each drive */
+static struct { u8 reg1, reg2, reg3, reg4; } regTab[4] = {
+ {0x03, 0x26, 0x04, 0x27}, /* drive 0 */
+ {0x05, 0x28, 0x06, 0x29}, /* drive 1 */
+ {0x2b, 0x30, 0x2c, 0x31}, /* drive 2 */
+ {0x2d, 0x32, 0x2e, 0x33}, /* drive 3 */
+};
+
+static int basePort; /* base port address */
+static int regPort; /* port for register number */
+static int dataPort; /* port for register data */
+static u8 regOn; /* output to base port to access registers */
+static u8 regOff; /* output to base port to close registers */
+
+/*------------------------------------------------------------------------*/
+
+/*
+ * Read a controller register.
+ */
+static inline u8 inReg(u8 reg)
+{
+ outb_p(reg, regPort);
+ return inb(dataPort);
+}
+
+/*
+ * Write a controller register.
+ */
+static void outReg(u8 data, u8 reg)
+{
+ outb_p(reg, regPort);
+ outb_p(data, dataPort);
+}
+
+static DEFINE_SPINLOCK(ali14xx_lock);
+
+/*
+ * Set PIO mode for the specified drive.
+ * This function computes timing parameters
+ * and sets controller registers accordingly.
+ */
+static void ali14xx_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+ int driveNum;
+ int time1, time2;
+ u8 param1, param2, param3, param4;
+ unsigned long flags;
+ int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;
+ const u8 pio = drive->pio_mode - XFER_PIO_0;
+ const struct ata_timing *t = ata_timing_find_mode(XFER_PIO_0 + pio);
+
+ /* calculate timing, according to PIO mode */
+ time1 = ide_pio_cycle_time(drive, pio);
+ time2 = t->active;
+ param3 = param1 = (time2 * bus_speed + 999) / 1000;
+ param4 = param2 = (time1 * bus_speed + 999) / 1000 - param1;
+ if (pio < 3) {
+ param3 += 8;
+ param4 += 8;
+ }
+ printk(KERN_DEBUG "%s: PIO mode%d, t1=%dns, t2=%dns, cycles = %d+%d, %d+%d\n",
+ drive->name, pio, time1, time2, param1, param2, param3, param4);
+
+ /* stuff timing parameters into controller registers */
+ driveNum = (drive->hwif->index << 1) + (drive->dn & 1);
+ spin_lock_irqsave(&ali14xx_lock, flags);
+ outb_p(regOn, basePort);
+ outReg(param1, regTab[driveNum].reg1);
+ outReg(param2, regTab[driveNum].reg2);
+ outReg(param3, regTab[driveNum].reg3);
+ outReg(param4, regTab[driveNum].reg4);
+ outb_p(regOff, basePort);
+ spin_unlock_irqrestore(&ali14xx_lock, flags);
+}
+
+/*
+ * Auto-detect the IDE controller port.
+ */
+static int __init findPort(void)
+{
+ int i;
+ u8 t;
+ unsigned long flags;
+
+ local_irq_save(flags);
+ for (i = 0; i < ALI_NUM_PORTS; ++i) {
+ basePort = ports[i];
+ regOff = inb(basePort);
+ for (regOn = 0x30; regOn <= 0x33; ++regOn) {
+ outb_p(regOn, basePort);
+ if (inb(basePort) == regOn) {
+ regPort = basePort + 4;
+ dataPort = basePort + 8;
+ t = inReg(0) & 0xf0;
+ outb_p(regOff, basePort);
+ local_irq_restore(flags);
+ if (t != 0x50)
+ return 0;
+ return 1; /* success */
+ }
+ }
+ outb_p(regOff, basePort);
+ }
+ local_irq_restore(flags);
+ return 0;
+}
+
+/*
+ * Initialize controller registers with default values.
+ */
+static int __init initRegisters(void)
+{
+ const RegInitializer *p;
+ u8 t;
+ unsigned long flags;
+
+ local_irq_save(flags);
+ outb_p(regOn, basePort);
+ for (p = initData; p->reg != 0; ++p)
+ outReg(p->data, p->reg);
+ outb_p(0x01, regPort);
+ t = inb(regPort) & 0x01;
+ outb_p(regOff, basePort);
+ local_irq_restore(flags);
+ return t;
+}
+
+static const struct ide_port_ops ali14xx_port_ops = {
+ .set_pio_mode = ali14xx_set_pio_mode,
+};
+
+static const struct ide_port_info ali14xx_port_info = {
+ .name = DRV_NAME,
+ .chipset = ide_ali14xx,
+ .port_ops = &ali14xx_port_ops,
+ .host_flags = IDE_HFLAG_NO_DMA,
+ .pio_mask = ATA_PIO4,
+};
+
+static int __init ali14xx_probe(void)
+{
+ printk(KERN_DEBUG "ali14xx: base=0x%03x, regOn=0x%02x.\n",
+ basePort, regOn);
+
+ /* initialize controller registers */
+ if (!initRegisters()) {
+ printk(KERN_ERR "ali14xx: Chip initialization failed.\n");
+ return 1;
+ }
+
+ return ide_legacy_device_add(&ali14xx_port_info, 0);
+}
+
+static int probe_ali14xx;
+
+module_param_named(probe, probe_ali14xx, bool, 0);
+MODULE_PARM_DESC(probe, "probe for ALI M14xx chipsets");
+
+static int __init ali14xx_init(void)
+{
+ if (probe_ali14xx == 0)
+ goto out;
+
+ /* auto-detect IDE controller port */
+ if (findPort()) {
+ if (ali14xx_probe())
+ return -ENODEV;
+ return 0;
+ }
+ printk(KERN_ERR "ali14xx: not found.\n");
+out:
+ return -ENODEV;
+}
+
+module_init(ali14xx_init);
+
+MODULE_AUTHOR("see local file");
+MODULE_DESCRIPTION("support of ALI 14XX IDE chipsets");
+MODULE_LICENSE("GPL");
Index: b/drivers/staging/ide-vlb/dtc2278.c
===================================================================
--- /dev/null
+++ b/drivers/staging/ide-vlb/dtc2278.c
@@ -0,0 +1,154 @@
+/*
+ * Copyright (C) 1996 Linus Torvalds & author (see below)
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/ioport.h>
+#include <linux/blkdev.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+
+#define DRV_NAME "dtc2278"
+
+/*
+ * Changing this #undef to #define may solve start up problems in some systems.
+ */
+#undef ALWAYS_SET_DTC2278_PIO_MODE
+
+/*
+ * From: andy@cercle.cts.com (Dyan Wile)
+ *
+ * Below is a patch for DTC-2278 - alike software-programmable controllers
+ * The code enables the secondary IDE controller and the PIO4 (3?) timings on
+ * the primary (EIDE). You may probably have to enable the 32-bit support to
+ * get the full speed. You better get the disk interrupts disabled ( hdparm -u0
+ * /dev/hd.. ) for the drives connected to the EIDE interface. (I get my
+ * filesystem corrupted with -u1, but under heavy disk load only :-)
+ *
+ * This card is now forced to use the "serialize" feature,
+ * and irq-unmasking is disallowed. If io_32bit is enabled,
+ * it must be done for BOTH drives on each interface.
+ *
+ * This code was written for the DTC2278E, but might work with any of these:
+ *
+ * DTC2278S has only a single IDE interface.
+ * DTC2278D has two IDE interfaces and is otherwise identical to the S version.
+ * DTC2278E also has serial ports and a printer port
+ * DTC2278EB: has onboard BIOS, and "works like a charm" -- Kent Bradford <kent@theory.caltech.edu>
+ *
+ * There may be a fourth controller type. The S and D versions use the
+ * Winbond chip, and I think the E version does also.
+ *
+ */
+
+static void sub22 (char b, char c)
+{
+ int i;
+
+ for(i = 0; i < 3; ++i) {
+ inb(0x3f6);
+ outb_p(b,0xb0);
+ inb(0x3f6);
+ outb_p(c,0xb4);
+ inb(0x3f6);
+ if(inb(0xb4) == c) {
+ outb_p(7,0xb0);
+ inb(0x3f6);
+ return; /* success */
+ }
+ }
+}
+
+static DEFINE_SPINLOCK(dtc2278_lock);
+
+static void dtc2278_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+ unsigned long flags;
+
+ if (drive->pio_mode >= XFER_PIO_3) {
+ spin_lock_irqsave(&dtc2278_lock, flags);
+ /*
+ * This enables PIO mode4 (3?) on the first interface
+ */
+ sub22(1,0xc3);
+ sub22(0,0xa0);
+ spin_unlock_irqrestore(&dtc2278_lock, flags);
+ } else {
+ /* we don't know how to set it back again.. */
+ /* Actually we do - there is a data sheet available for the
+ Winbond but does anyone actually care */
+ }
+}
+
+static const struct ide_port_ops dtc2278_port_ops = {
+ .set_pio_mode = dtc2278_set_pio_mode,
+};
+
+static const struct ide_port_info dtc2278_port_info __initdata = {
+ .name = DRV_NAME,
+ .chipset = ide_dtc2278,
+ .port_ops = &dtc2278_port_ops,
+ .host_flags = IDE_HFLAG_SERIALIZE |
+ IDE_HFLAG_NO_UNMASK_IRQS |
+ IDE_HFLAG_IO_32BIT |
+ /* disallow ->io_32bit changes */
+ IDE_HFLAG_NO_IO_32BIT |
+ IDE_HFLAG_NO_DMA |
+ IDE_HFLAG_DTC2278,
+ .pio_mask = ATA_PIO4,
+};
+
+static int __init dtc2278_probe(void)
+{
+ unsigned long flags;
+
+ local_irq_save(flags);
+ /*
+ * This enables the second interface
+ */
+ outb_p(4,0xb0);
+ inb(0x3f6);
+ outb_p(0x20,0xb4);
+ inb(0x3f6);
+#ifdef ALWAYS_SET_DTC2278_PIO_MODE
+ /*
+ * This enables PIO mode4 (3?) on the first interface
+ * and may solve start-up problems for some people.
+ */
+ sub22(1,0xc3);
+ sub22(0,0xa0);
+#endif
+ local_irq_restore(flags);
+
+ return ide_legacy_device_add(&dtc2278_port_info, 0);
+}
+
+static int probe_dtc2278;
+
+module_param_named(probe, probe_dtc2278, bool, 0);
+MODULE_PARM_DESC(probe, "probe for DTC2278xx chipsets");
+
+static int __init dtc2278_init(void)
+{
+ if (probe_dtc2278 == 0)
+ return -ENODEV;
+
+ if (dtc2278_probe()) {
+ printk(KERN_ERR "dtc2278: ide interfaces already in use!\n");
+ return -EBUSY;
+ }
+ return 0;
+}
+
+module_init(dtc2278_init);
+
+MODULE_AUTHOR("See Local File");
+MODULE_DESCRIPTION("support of DTC-2278 VLB IDE chipsets");
+MODULE_LICENSE("GPL");
Index: b/drivers/staging/ide-vlb/ht6560b.c
===================================================================
--- /dev/null
+++ b/drivers/staging/ide-vlb/ht6560b.c
@@ -0,0 +1,384 @@
+/*
+ * Copyright (C) 1995-2000 Linus Torvalds & author (see below)
+ */
+
+/*
+ * HT-6560B EIDE-controller support
+ * To activate controller support use kernel parameter "ide0=ht6560b".
+ * Use hdparm utility to enable PIO mode support.
+ *
+ * Author: Mikko Ala-Fossi <maf@iki.fi>
+ * Jan Evert van Grootheest <j.e.van.grootheest@caiway.nl>
+ *
+ * Try: http://www.maf.iki.fi/~maf/ht6560b/
+ */
+
+#define DRV_NAME "ht6560b"
+#define HT6560B_VERSION "v0.08"
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/ioport.h>
+#include <linux/blkdev.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+
+/* #define DEBUG */ /* remove comments for DEBUG messages */
+
+/*
+ * The special i/o-port that HT-6560B uses to configuration:
+ * bit0 (0x01): "1" selects secondary interface
+ * bit2 (0x04): "1" enables FIFO function
+ * bit5 (0x20): "1" enables prefetched data read function (???)
+ *
+ * The special i/o-port that HT-6560A uses to configuration:
+ * bit0 (0x01): "1" selects secondary interface
+ * bit1 (0x02): "1" enables prefetched data read function
+ * bit2 (0x04): "0" enables multi-master system (?)
+ * bit3 (0x08): "1" 3 cycle time, "0" 2 cycle time (?)
+ */
+#define HT_CONFIG_PORT 0x3e6
+
+static inline u8 HT_CONFIG(ide_drive_t *drive)
+{
+ return ((unsigned long)ide_get_drivedata(drive) & 0xff00) >> 8;
+}
+
+/*
+ * FIFO + PREFETCH (both a/b-model)
+ */
+#define HT_CONFIG_DEFAULT 0x1c /* no prefetch */
+/* #define HT_CONFIG_DEFAULT 0x3c */ /* with prefetch */
+#define HT_SECONDARY_IF 0x01
+#define HT_PREFETCH_MODE 0x20
+
+/*
+ * ht6560b Timing values:
+ *
+ * I reviewed some assembler source listings of htide drivers and found
+ * out how they setup those cycle time interfacing values, as they at Holtek
+ * call them. IDESETUP.COM that is supplied with the drivers figures out
+ * optimal values and fetches those values to drivers. I found out that
+ * they use Select register to fetch timings to the ide board right after
+ * interface switching. After that it was quite easy to add code to
+ * ht6560b.c.
+ *
+ * IDESETUP.COM gave me values 0x24, 0x45, 0xaa, 0xff that worked fine
+ * for hda and hdc. But hdb needed higher values to work, so I guess
+ * that sometimes it is necessary to give higher value than IDESETUP
+ * gives. [see cmd640.c for an extreme example of this. -ml]
+ *
+ * Perhaps I should explain something about these timing values:
+ * The higher nibble of value is the Recovery Time (rt) and the lower nibble
+ * of the value is the Active Time (at). Minimum value 2 is the fastest and
+ * the maximum value 15 is the slowest. Default values should be 15 for both.
+ * So 0x24 means 2 for rt and 4 for at. Each of the drives should have
+ * both values, and IDESETUP gives automatically rt=15 st=15 for CDROMs or
+ * similar. If value is too small there will be all sorts of failures.
+ *
+ * Timing byte consists of
+ * High nibble: Recovery Cycle Time (rt)
+ * The valid values range from 2 to 15. The default is 15.
+ *
+ * Low nibble: Active Cycle Time (at)
+ * The valid values range from 2 to 15. The default is 15.
+ *
+ * You can obtain optimized timing values by running Holtek IDESETUP.COM
+ * for DOS. DOS drivers get their timing values from command line, where
+ * the first value is the Recovery Time and the second value is the
+ * Active Time for each drive. Smaller value gives higher speed.
+ * In case of failures you should probably fall back to a higher value.
+ */
+static inline u8 HT_TIMING(ide_drive_t *drive)
+{
+ return (unsigned long)ide_get_drivedata(drive) & 0x00ff;
+}
+
+#define HT_TIMING_DEFAULT 0xff
+
+/*
+ * This routine handles interface switching for the peculiar hardware design
+ * on the F.G.I./Holtek HT-6560B VLB IDE interface.
+ * The HT-6560B can only enable one IDE port at a time, and requires a
+ * silly sequence (below) whenever we switch between primary and secondary.
+ */
+
+/*
+ * This routine is invoked from ide.c to prepare for access to a given drive.
+ */
+static void ht6560b_dev_select(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ unsigned long flags;
+ static u8 current_select = 0;
+ static u8 current_timing = 0;
+ u8 select, timing;
+
+ local_irq_save(flags);
+
+ select = HT_CONFIG(drive);
+ timing = HT_TIMING(drive);
+
+ /*
+ * Need to enforce prefetch sometimes because otherwise
+ * it'll hang (hard).
+ */
+ if (drive->media != ide_disk ||
+ (drive->dev_flags & IDE_DFLAG_PRESENT) == 0)
+ select |= HT_PREFETCH_MODE;
+
+ if (select != current_select || timing != current_timing) {
+ current_select = select;
+ current_timing = timing;
+ (void)inb(HT_CONFIG_PORT);
+ (void)inb(HT_CONFIG_PORT);
+ (void)inb(HT_CONFIG_PORT);
+ (void)inb(HT_CONFIG_PORT);
+ outb(select, HT_CONFIG_PORT);
+ /*
+ * Set timing for this drive:
+ */
+ outb(timing, hwif->io_ports.device_addr);
+ (void)inb(hwif->io_ports.status_addr);
+#ifdef DEBUG
+ printk("ht6560b: %s: select=%#x timing=%#x\n",
+ drive->name, select, timing);
+#endif
+ }
+ local_irq_restore(flags);
+
+ outb(drive->select | ATA_DEVICE_OBS, hwif->io_ports.device_addr);
+}
+
+/*
+ * Autodetection and initialization of ht6560b
+ */
+static int __init try_to_init_ht6560b(void)
+{
+ u8 orig_value;
+ int i;
+
+ /* Autodetect ht6560b */
+ if ((orig_value = inb(HT_CONFIG_PORT)) == 0xff)
+ return 0;
+
+ for (i=3;i>0;i--) {
+ outb(0x00, HT_CONFIG_PORT);
+ if (!( (~inb(HT_CONFIG_PORT)) & 0x3f )) {
+ outb(orig_value, HT_CONFIG_PORT);
+ return 0;
+ }
+ }
+ outb(0x00, HT_CONFIG_PORT);
+ if ((~inb(HT_CONFIG_PORT))& 0x3f) {
+ outb(orig_value, HT_CONFIG_PORT);
+ return 0;
+ }
+ /*
+ * Ht6560b autodetected
+ */
+ outb(HT_CONFIG_DEFAULT, HT_CONFIG_PORT);
+ outb(HT_TIMING_DEFAULT, 0x1f6); /* Select register */
+ (void)inb(0x1f7); /* Status register */
+
+ printk("ht6560b " HT6560B_VERSION
+ ": chipset detected and initialized"
+#ifdef DEBUG
+ " with debug enabled"
+#endif
+ "\n"
+ );
+ return 1;
+}
+
+static u8 ht_pio2timings(ide_drive_t *drive, const u8 pio)
+{
+ int active_time, recovery_time;
+ int active_cycles, recovery_cycles;
+ int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;
+
+ if (pio) {
+ unsigned int cycle_time;
+ const struct ata_timing *t =
+ ata_timing_find_mode(XFER_PIO_0 + pio);
+
+ cycle_time = ide_pio_cycle_time(drive, pio);
+
+ /*
+ * Just like opti621.c we try to calculate the
+ * actual cycle time for recovery and activity
+ * according system bus speed.
+ */
+ active_time = t->active;
+ recovery_time = cycle_time - active_time - t->setup;
+ /*
+ * Cycle times should be Vesa bus cycles
+ */
+ active_cycles = (active_time * bus_speed + 999) / 1000;
+ recovery_cycles = (recovery_time * bus_speed + 999) / 1000;
+ /*
+ * Upper and lower limits
+ */
+ if (active_cycles < 2) active_cycles = 2;
+ if (recovery_cycles < 2) recovery_cycles = 2;
+ if (active_cycles > 15) active_cycles = 15;
+ if (recovery_cycles > 15) recovery_cycles = 0; /* 0==16 */
+
+#ifdef DEBUG
+ printk("ht6560b: drive %s setting pio=%d recovery=%d (%dns) active=%d (%dns)\n", drive->name, pio, recovery_cycles, recovery_time, active_cycles, active_time);
+#endif
+
+ return (u8)((recovery_cycles << 4) | active_cycles);
+ } else {
+
+#ifdef DEBUG
+ printk("ht6560b: drive %s setting pio=0\n", drive->name);
+#endif
+
+ return HT_TIMING_DEFAULT; /* default setting */
+ }
+}
+
+static DEFINE_SPINLOCK(ht6560b_lock);
+
+/*
+ * Enable/Disable so called prefetch mode
+ */
+static void ht_set_prefetch(ide_drive_t *drive, u8 state)
+{
+ unsigned long flags, config;
+ int t = HT_PREFETCH_MODE << 8;
+
+ spin_lock_irqsave(&ht6560b_lock, flags);
+
+ config = (unsigned long)ide_get_drivedata(drive);
+
+ /*
+ * Prefetch mode and unmask irq seems to conflict
+ */
+ if (state) {
+ config |= t; /* enable prefetch mode */
+ drive->dev_flags |= IDE_DFLAG_NO_UNMASK;
+ drive->dev_flags &= ~IDE_DFLAG_UNMASK;
+ } else {
+ config &= ~t; /* disable prefetch mode */
+ drive->dev_flags &= ~IDE_DFLAG_NO_UNMASK;
+ }
+
+ ide_set_drivedata(drive, (void *)config);
+
+ spin_unlock_irqrestore(&ht6560b_lock, flags);
+
+#ifdef DEBUG
+ printk("ht6560b: drive %s prefetch mode %sabled\n", drive->name, (state ? "en" : "dis"));
+#endif
+}
+
+static void ht6560b_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+ unsigned long flags, config;
+ const u8 pio = drive->pio_mode - XFER_PIO_0;
+ u8 timing;
+
+ switch (pio) {
+ case 8: /* set prefetch off */
+ case 9: /* set prefetch on */
+ ht_set_prefetch(drive, pio & 1);
+ return;
+ }
+
+ timing = ht_pio2timings(drive, pio);
+
+ spin_lock_irqsave(&ht6560b_lock, flags);
+ config = (unsigned long)ide_get_drivedata(drive);
+ config &= 0xff00;
+ config |= timing;
+ ide_set_drivedata(drive, (void *)config);
+ spin_unlock_irqrestore(&ht6560b_lock, flags);
+
+#ifdef DEBUG
+ printk("ht6560b: drive %s tuned to pio mode %#x timing=%#x\n", drive->name, pio, timing);
+#endif
+}
+
+static void __init ht6560b_init_dev(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ /* Setting default configurations for drives. */
+ int t = (HT_CONFIG_DEFAULT << 8) | HT_TIMING_DEFAULT;
+
+ if (hwif->channel)
+ t |= (HT_SECONDARY_IF << 8);
+
+ ide_set_drivedata(drive, (void *)t);
+}
+
+static int probe_ht6560b;
+
+module_param_named(probe, probe_ht6560b, bool, 0);
+MODULE_PARM_DESC(probe, "probe for HT6560B chipset");
+
+static const struct ide_tp_ops ht6560b_tp_ops = {
+ .exec_command = ide_exec_command,
+ .read_status = ide_read_status,
+ .read_altstatus = ide_read_altstatus,
+ .write_devctl = ide_write_devctl,
+
+ .dev_select = ht6560b_dev_select,
+ .tf_load = ide_tf_load,
+ .tf_read = ide_tf_read,
+
+ .input_data = ide_input_data,
+ .output_data = ide_output_data,
+};
+
+static const struct ide_port_ops ht6560b_port_ops = {
+ .init_dev = ht6560b_init_dev,
+ .set_pio_mode = ht6560b_set_pio_mode,
+};
+
+static const struct ide_port_info ht6560b_port_info __initdata = {
+ .name = DRV_NAME,
+ .chipset = ide_ht6560b,
+ .tp_ops = &ht6560b_tp_ops,
+ .port_ops = &ht6560b_port_ops,
+ .host_flags = IDE_HFLAG_SERIALIZE | /* is this needed? */
+ IDE_HFLAG_NO_DMA |
+ IDE_HFLAG_ABUSE_PREFETCH,
+ .pio_mask = ATA_PIO4,
+};
+
+static int __init ht6560b_init(void)
+{
+ if (probe_ht6560b == 0)
+ return -ENODEV;
+
+ if (!request_region(HT_CONFIG_PORT, 1, DRV_NAME)) {
+ printk(KERN_NOTICE "%s: HT_CONFIG_PORT not found\n",
+ __func__);
+ return -ENODEV;
+ }
+
+ if (!try_to_init_ht6560b()) {
+ printk(KERN_NOTICE "%s: HBA not found\n", __func__);
+ goto release_region;
+ }
+
+ return ide_legacy_device_add(&ht6560b_port_info, 0);
+
+release_region:
+ release_region(HT_CONFIG_PORT, 1);
+ return -ENODEV;
+}
+
+module_init(ht6560b_init);
+
+MODULE_AUTHOR("See Local File");
+MODULE_DESCRIPTION("HT-6560B EIDE-controller support");
+MODULE_LICENSE("GPL");
Index: b/drivers/staging/ide-vlb/ide-4drives.c
===================================================================
--- /dev/null
+++ b/drivers/staging/ide-vlb/ide-4drives.c
@@ -0,0 +1,64 @@
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/ide.h>
+
+#define DRV_NAME "ide-4drives"
+
+static int probe_4drives;
+
+module_param_named(probe, probe_4drives, bool, 0);
+MODULE_PARM_DESC(probe, "probe for generic IDE chipset with 4 drives/port");
+
+static void ide_4drives_init_dev(ide_drive_t *drive)
+{
+ if (drive->hwif->channel)
+ drive->select ^= 0x20;
+}
+
+static const struct ide_port_ops ide_4drives_port_ops = {
+ .init_dev = ide_4drives_init_dev,
+};
+
+static const struct ide_port_info ide_4drives_port_info = {
+ .port_ops = &ide_4drives_port_ops,
+ .host_flags = IDE_HFLAG_SERIALIZE | IDE_HFLAG_NO_DMA |
+ IDE_HFLAG_4DRIVES,
+ .chipset = ide_4drives,
+};
+
+static int __init ide_4drives_init(void)
+{
+ unsigned long base = 0x1f0, ctl = 0x3f6;
+ struct ide_hw hw, *hws[] = { &hw, &hw };
+
+ if (probe_4drives == 0)
+ return -ENODEV;
+
+ if (!request_region(base, 8, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n",
+ DRV_NAME, base, base + 7);
+ return -EBUSY;
+ }
+
+ if (!request_region(ctl, 1, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX not free.\n",
+ DRV_NAME, ctl);
+ release_region(base, 8);
+ return -EBUSY;
+ }
+
+ memset(&hw, 0, sizeof(hw));
+
+ ide_std_init_ports(&hw, base, ctl);
+ hw.irq = 14;
+
+ return ide_host_add(&ide_4drives_port_info, hws, 2, NULL);
+}
+
+module_init(ide_4drives_init);
+
+MODULE_AUTHOR("Bartlomiej Zolnierkiewicz");
+MODULE_DESCRIPTION("generic IDE chipset with 4 drives/port support");
+MODULE_LICENSE("GPL");
Index: b/drivers/staging/ide-vlb/qd65xx.c
===================================================================
--- /dev/null
+++ b/drivers/staging/ide-vlb/qd65xx.c
@@ -0,0 +1,446 @@
+/*
+ * Copyright (C) 1996-2001 Linus Torvalds & author (see below)
+ */
+
+/*
+ * Version 0.03 Cleaned auto-tune, added probe
+ * Version 0.04 Added second channel tuning
+ * Version 0.05 Enhanced tuning ; added qd6500 support
+ * Version 0.06 Added dos driver's list
+ * Version 0.07 Second channel bug fix
+ *
+ * QDI QD6500/QD6580 EIDE controller fast support
+ *
+ * To activate controller support, use "ide0=qd65xx"
+ */
+
+/*
+ * Rewritten from the work of Colten Edwards <pje120@cs.usask.ca> by
+ * Samuel Thibault <samuel.thibault@ens-lyon.org>
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/ioport.h>
+#include <linux/blkdev.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+#include <asm/system.h>
+#include <asm/io.h>
+
+#define DRV_NAME "qd65xx"
+
+#include "qd65xx.h"
+
+/*
+ * I/O ports are 0x30-0x31 (and 0x32-0x33 for qd6580)
+ * or 0xb0-0xb1 (and 0xb2-0xb3 for qd6580)
+ * -- qd6500 is a single IDE interface
+ * -- qd6580 is a dual IDE interface
+ *
+ * More research on qd6580 being done by willmore@cig.mot.com (David)
+ * More Information given by Petr Soucek (petr@ryston.cz)
+ * http://www.ryston.cz/petr/vlb
+ */
+
+/*
+ * base: Timer1
+ *
+ *
+ * base+0x01: Config (R/O)
+ *
+ * bit 0: ide baseport: 1 = 0x1f0 ; 0 = 0x170 (only useful for qd6500)
+ * bit 1: qd65xx baseport: 1 = 0xb0 ; 0 = 0x30
+ * bit 2: ID3: bus speed: 1 = <=33MHz ; 0 = >33MHz
+ * bit 3: qd6500: 1 = disabled, 0 = enabled
+ * qd6580: 1
+ * upper nibble:
+ * qd6500: 1100
+ * qd6580: either 1010 or 0101
+ *
+ *
+ * base+0x02: Timer2 (qd6580 only)
+ *
+ *
+ * base+0x03: Control (qd6580 only)
+ *
+ * bits 0-3 must always be set 1
+ * bit 4 must be set 1, but is set 0 by dos driver while measuring vlb clock
+ * bit 0 : 1 = Only primary port enabled : channel 0 for hda, channel 1 for hdb
+ * 0 = Primary and Secondary ports enabled : channel 0 for hda & hdb
+ * channel 1 for hdc & hdd
+ * bit 1 : 1 = only disks on primary port
+ * 0 = disks & ATAPI devices on primary port
+ * bit 2-4 : always 0
+ * bit 5 : status, but of what ?
+ * bit 6 : always set 1 by dos driver
+ * bit 7 : set 1 for non-ATAPI devices on primary port
+ * (maybe read-ahead and post-write buffer ?)
+ */
+
+static int timings[4]={-1,-1,-1,-1}; /* stores current timing for each timer */
+
+/*
+ * qd65xx_select:
+ *
+ * This routine is invoked to prepare for access to a given drive.
+ */
+
+static void qd65xx_dev_select(ide_drive_t *drive)
+{
+ u8 index = (( (QD_TIMREG(drive)) & 0x80 ) >> 7) |
+ (QD_TIMREG(drive) & 0x02);
+
+ if (timings[index] != QD_TIMING(drive))
+ outb(timings[index] = QD_TIMING(drive), QD_TIMREG(drive));
+
+ outb(drive->select | ATA_DEVICE_OBS, drive->hwif->io_ports.device_addr);
+}
+
+/*
+ * qd6500_compute_timing
+ *
+ * computes the timing value where
+ * lower nibble represents active time, in count of VLB clocks
+ * upper nibble represents recovery time, in count of VLB clocks
+ */
+
+static u8 qd6500_compute_timing (ide_hwif_t *hwif, int active_time, int recovery_time)
+{
+ int clk = ide_vlb_clk ? ide_vlb_clk : 50;
+ u8 act_cyc, rec_cyc;
+
+ if (clk <= 33) {
+ act_cyc = 9 - IDE_IN(active_time * clk / 1000 + 1, 2, 9);
+ rec_cyc = 15 - IDE_IN(recovery_time * clk / 1000 + 1, 0, 15);
+ } else {
+ act_cyc = 8 - IDE_IN(active_time * clk / 1000 + 1, 1, 8);
+ rec_cyc = 18 - IDE_IN(recovery_time * clk / 1000 + 1, 3, 18);
+ }
+
+ return (rec_cyc << 4) | 0x08 | act_cyc;
+}
+
+/*
+ * qd6580_compute_timing
+ *
+ * idem for qd6580
+ */
+
+static u8 qd6580_compute_timing (int active_time, int recovery_time)
+{
+ int clk = ide_vlb_clk ? ide_vlb_clk : 50;
+ u8 act_cyc, rec_cyc;
+
+ act_cyc = 17 - IDE_IN(active_time * clk / 1000 + 1, 2, 17);
+ rec_cyc = 15 - IDE_IN(recovery_time * clk / 1000 + 1, 2, 15);
+
+ return (rec_cyc << 4) | act_cyc;
+}
+
+/*
+ * qd_find_disk_type
+ *
+ * tries to find timing from dos driver's table
+ */
+
+static int qd_find_disk_type (ide_drive_t *drive,
+ int *active_time, int *recovery_time)
+{
+ struct qd65xx_timing_s *p;
+ char *m = (char *)&drive->id[ATA_ID_PROD];
+ char model[ATA_ID_PROD_LEN];
+
+ if (*m == 0)
+ return 0;
+
+ strncpy(model, m, ATA_ID_PROD_LEN);
+ ide_fixstring(model, ATA_ID_PROD_LEN, 1); /* byte-swap */
+
+ for (p = qd65xx_timing ; p->offset != -1 ; p++) {
+ if (!strncmp(p->model, model+p->offset, 4)) {
+ printk(KERN_DEBUG "%s: listed !\n", drive->name);
+ *active_time = p->active;
+ *recovery_time = p->recovery;
+ return 1;
+ }
+ }
+ return 0;
+}
+
+/*
+ * qd_set_timing:
+ *
+ * records the timing
+ */
+
+static void qd_set_timing (ide_drive_t *drive, u8 timing)
+{
+ unsigned long data = (unsigned long)ide_get_drivedata(drive);
+
+ data &= 0xff00;
+ data |= timing;
+ ide_set_drivedata(drive, (void *)data);
+
+ printk(KERN_DEBUG "%s: %#x\n", drive->name, timing);
+}
+
+static void qd6500_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+ u16 *id = drive->id;
+ int active_time = 175;
+ int recovery_time = 415; /* worst case values from the dos driver */
+
+ /* FIXME: use drive->pio_mode value */
+ if (!qd_find_disk_type(drive, &active_time, &recovery_time) &&
+ (id[ATA_ID_OLD_PIO_MODES] & 0xff) && (id[ATA_ID_FIELD_VALID] & 2) &&
+ id[ATA_ID_EIDE_PIO] >= 240) {
+ printk(KERN_INFO "%s: PIO mode%d\n", drive->name,
+ id[ATA_ID_OLD_PIO_MODES] & 0xff);
+ active_time = 110;
+ recovery_time = drive->id[ATA_ID_EIDE_PIO] - 120;
+ }
+
+ qd_set_timing(drive, qd6500_compute_timing(drive->hwif,
+ active_time, recovery_time));
+}
+
+static void qd6580_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+ const u8 pio = drive->pio_mode - XFER_PIO_0;
+ const struct ata_timing *t = ata_timing_find_mode(XFER_PIO_0 + pio);
+ unsigned int cycle_time;
+ int active_time = 175;
+ int recovery_time = 415; /* worst case values from the dos driver */
+ u8 base = (hwif->config_data & 0xff00) >> 8;
+
+ if (drive->id && !qd_find_disk_type(drive, &active_time, &recovery_time)) {
+ cycle_time = ide_pio_cycle_time(drive, pio);
+
+ switch (pio) {
+ case 0: break;
+ case 3:
+ if (cycle_time >= 110) {
+ active_time = 86;
+ recovery_time = cycle_time - 102;
+ } else
+ printk(KERN_WARNING "%s: Strange recovery time !\n",drive->name);
+ break;
+ case 4:
+ if (cycle_time >= 69) {
+ active_time = 70;
+ recovery_time = cycle_time - 61;
+ } else
+ printk(KERN_WARNING "%s: Strange recovery time !\n",drive->name);
+ break;
+ default:
+ if (cycle_time >= 180) {
+ active_time = 110;
+ recovery_time = cycle_time - 120;
+ } else {
+ active_time = t->active;
+ recovery_time = cycle_time - active_time;
+ }
+ }
+ printk(KERN_INFO "%s: PIO mode%d\n", drive->name,pio);
+ }
+
+ if (!hwif->channel && drive->media != ide_disk) {
+ outb(0x5f, QD_CONTROL_PORT);
+ printk(KERN_WARNING "%s: ATAPI: disabled read-ahead FIFO "
+ "and post-write buffer on %s.\n",
+ drive->name, hwif->name);
+ }
+
+ qd_set_timing(drive, qd6580_compute_timing(active_time, recovery_time));
+}
+
+/*
+ * qd_testreg
+ *
+ * tests if the given port is a register
+ */
+
+static int __init qd_testreg(int port)
+{
+ unsigned long flags;
+ u8 savereg, readreg;
+
+ local_irq_save(flags);
+ savereg = inb_p(port);
+ outb_p(QD_TESTVAL, port); /* safe value */
+ readreg = inb_p(port);
+ outb(savereg, port);
+ local_irq_restore(flags);
+
+ if (savereg == QD_TESTVAL) {
+ printk(KERN_ERR "Outch ! the probe for qd65xx isn't reliable !\n");
+ printk(KERN_ERR "Please contact maintainers to tell about your hardware\n");
+ printk(KERN_ERR "Assuming qd65xx is not present.\n");
+ return 1;
+ }
+
+ return (readreg != QD_TESTVAL);
+}
+
+static void __init qd6500_init_dev(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ u8 base = (hwif->config_data & 0xff00) >> 8;
+ u8 config = QD_CONFIG(hwif);
+
+ ide_set_drivedata(drive, (void *)QD6500_DEF_DATA);
+}
+
+static void __init qd6580_init_dev(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ u16 t1, t2;
+ u8 base = (hwif->config_data & 0xff00) >> 8;
+ u8 config = QD_CONFIG(hwif);
+
+ if (hwif->host_flags & IDE_HFLAG_SINGLE) {
+ t1 = QD6580_DEF_DATA;
+ t2 = QD6580_DEF_DATA2;
+ } else
+ t2 = t1 = hwif->channel ? QD6580_DEF_DATA2 : QD6580_DEF_DATA;
+
+ ide_set_drivedata(drive, (void *)((drive->dn & 1) ? t2 : t1));
+}
+
+static const struct ide_tp_ops qd65xx_tp_ops = {
+ .exec_command = ide_exec_command,
+ .read_status = ide_read_status,
+ .read_altstatus = ide_read_altstatus,
+ .write_devctl = ide_write_devctl,
+
+ .dev_select = qd65xx_dev_select,
+ .tf_load = ide_tf_load,
+ .tf_read = ide_tf_read,
+
+ .input_data = ide_input_data,
+ .output_data = ide_output_data,
+};
+
+static const struct ide_port_ops qd6500_port_ops = {
+ .init_dev = qd6500_init_dev,
+ .set_pio_mode = qd6500_set_pio_mode,
+};
+
+static const struct ide_port_ops qd6580_port_ops = {
+ .init_dev = qd6580_init_dev,
+ .set_pio_mode = qd6580_set_pio_mode,
+};
+
+static const struct ide_port_info qd65xx_port_info __initdata = {
+ .name = DRV_NAME,
+ .tp_ops = &qd65xx_tp_ops,
+ .chipset = ide_qd65xx,
+ .host_flags = IDE_HFLAG_IO_32BIT |
+ IDE_HFLAG_NO_DMA,
+ .pio_mask = ATA_PIO4,
+};
+
+/*
+ * qd_probe:
+ *
+ * looks at the specified baseport, and if qd found, registers & initialises it
+ * return 1 if another qd may be probed
+ */
+
+static int __init qd_probe(int base)
+{
+ int rc;
+ u8 config, unit, control;
+ struct ide_port_info d = qd65xx_port_info;
+
+ config = inb(QD_CONFIG_PORT);
+
+ if (! ((config & QD_CONFIG_BASEPORT) >> 1 == (base == 0xb0)) )
+ return -ENODEV;
+
+ unit = ! (config & QD_CONFIG_IDE_BASEPORT);
+
+ if (unit)
+ d.host_flags |= IDE_HFLAG_QD_2ND_PORT;
+
+ switch (config & 0xf0) {
+ case QD_CONFIG_QD6500:
+ if (qd_testreg(base))
+ return -ENODEV; /* bad register */
+
+ if (config & QD_CONFIG_DISABLED) {
+ printk(KERN_WARNING "qd6500 is disabled !\n");
+ return -ENODEV;
+ }
+
+ printk(KERN_NOTICE "qd6500 at %#x\n", base);
+ printk(KERN_DEBUG "qd6500: config=%#x, ID3=%u\n",
+ config, QD_ID3);
+
+ d.port_ops = &qd6500_port_ops;
+ d.host_flags |= IDE_HFLAG_SINGLE;
+ break;
+ case QD_CONFIG_QD6580_A:
+ case QD_CONFIG_QD6580_B:
+ if (qd_testreg(base) || qd_testreg(base + 0x02))
+ return -ENODEV; /* bad registers */
+
+ control = inb(QD_CONTROL_PORT);
+
+ printk(KERN_NOTICE "qd6580 at %#x\n", base);
+ printk(KERN_DEBUG "qd6580: config=%#x, control=%#x, ID3=%u\n",
+ config, control, QD_ID3);
+
+ outb(QD_DEF_CONTR, QD_CONTROL_PORT);
+
+ d.port_ops = &qd6580_port_ops;
+ if (control & QD_CONTR_SEC_DISABLED)
+ d.host_flags |= IDE_HFLAG_SINGLE;
+
+ printk(KERN_INFO "qd6580: %s IDE board\n",
+ (control & QD_CONTR_SEC_DISABLED) ? "single" : "dual");
+ break;
+ default:
+ return -ENODEV;
+ }
+
+ rc = ide_legacy_device_add(&d, (base << 8) | config);
+
+ if (d.host_flags & IDE_HFLAG_SINGLE)
+ return (rc == 0) ? 1 : rc;
+
+ return rc;
+}
+
+static int probe_qd65xx;
+
+module_param_named(probe, probe_qd65xx, bool, 0);
+MODULE_PARM_DESC(probe, "probe for QD65xx chipsets");
+
+static int __init qd65xx_init(void)
+{
+ int rc1, rc2 = -ENODEV;
+
+ if (probe_qd65xx == 0)
+ return -ENODEV;
+
+ rc1 = qd_probe(0x30);
+ if (rc1)
+ rc2 = qd_probe(0xb0);
+
+ if (rc1 < 0 && rc2 < 0)
+ return -ENODEV;
+
+ return 0;
+}
+
+module_init(qd65xx_init);
+
+MODULE_AUTHOR("Samuel Thibault");
+MODULE_DESCRIPTION("support of qd65xx vlb ide chipset");
+MODULE_LICENSE("GPL");
Index: b/drivers/staging/ide-vlb/qd65xx.h
===================================================================
--- /dev/null
+++ b/drivers/staging/ide-vlb/qd65xx.h
@@ -0,0 +1,144 @@
+/*
+ * Copyright (c) 2000 Linus Torvalds & authors
+ */
+
+/*
+ * Authors: Petr Soucek <petr@ryston.cz>
+ * Samuel Thibault <samuel.thibault@ens-lyon.org>
+ */
+
+/* truncates a in [b,c] */
+#define IDE_IN(a,b,c) ( ((a)<(b)) ? (b) : ( (a)>(c) ? (c) : (a)) )
+
+#define IDE_IMPLY(a,b) ((!(a)) || (b))
+
+#define QD_TIM1_PORT (base)
+#define QD_CONFIG_PORT (base+0x01)
+#define QD_TIM2_PORT (base+0x02)
+#define QD_CONTROL_PORT (base+0x03)
+
+#define QD_CONFIG_IDE_BASEPORT 0x01
+#define QD_CONFIG_BASEPORT 0x02
+#define QD_CONFIG_ID3 0x04
+#define QD_CONFIG_DISABLED 0x08
+#define QD_CONFIG_QD6500 0xc0
+#define QD_CONFIG_QD6580_A 0xa0
+#define QD_CONFIG_QD6580_B 0x50
+
+#define QD_CONTR_SEC_DISABLED 0x01
+
+#define QD_ID3 ((config & QD_CONFIG_ID3)!=0)
+
+#define QD_CONFIG(hwif) ((hwif)->config_data & 0x00ff)
+
+static inline u8 QD_TIMING(ide_drive_t *drive)
+{
+ return (unsigned long)ide_get_drivedata(drive) & 0x00ff;
+}
+
+static inline u8 QD_TIMREG(ide_drive_t *drive)
+{
+ return ((unsigned long)ide_get_drivedata(drive) & 0xff00) >> 8;
+}
+
+#define QD6500_DEF_DATA ((QD_TIM1_PORT<<8) | (QD_ID3 ? 0x0c : 0x08))
+#define QD6580_DEF_DATA ((QD_TIM1_PORT<<8) | (QD_ID3 ? 0x0a : 0x00))
+#define QD6580_DEF_DATA2 ((QD_TIM2_PORT<<8) | (QD_ID3 ? 0x0a : 0x00))
+#define QD_DEF_CONTR (0x40 | ((control & 0x02) ? 0x9f : 0x1f))
+
+#define QD_TESTVAL 0x19 /* safe value */
+
+/* Drive specific timing taken from DOS driver v3.7 */
+
+static struct qd65xx_timing_s {
+ s8 offset; /* ofset from the beginning of Model Number" */
+ char model[4]; /* 4 chars from Model number, no conversion */
+ s16 active; /* active time */
+ s16 recovery; /* recovery time */
+} qd65xx_timing [] = {
+ { 30, "2040", 110, 225 }, /* Conner CP30204 */
+ { 30, "2045", 135, 225 }, /* Conner CP30254 */
+ { 30, "1040", 155, 325 }, /* Conner CP30104 */
+ { 30, "1047", 135, 265 }, /* Conner CP30174 */
+ { 30, "5344", 135, 225 }, /* Conner CP3544 */
+ { 30, "01 4", 175, 405 }, /* Conner CP-3104 */
+ { 27, "C030", 175, 375 }, /* Conner CP3000 */
+ { 8, "PL42", 110, 295 }, /* Quantum LP240 */
+ { 8, "PL21", 110, 315 }, /* Quantum LP120 */
+ { 8, "PL25", 175, 385 }, /* Quantum LP52 */
+ { 4, "PA24", 110, 285 }, /* WD Piranha SP4200 */
+ { 6, "2200", 110, 260 }, /* WD Caviar AC2200 */
+ { 6, "3204", 110, 235 }, /* WD Caviar AC2340 */
+ { 6, "1202", 110, 265 }, /* WD Caviar AC2120 */
+ { 0, "DS3-", 135, 315 }, /* Teac SD340 */
+ { 8, "KM32", 175, 355 }, /* Toshiba MK234 */
+ { 2, "53A1", 175, 355 }, /* Seagate ST351A */
+ { 2, "4108", 175, 295 }, /* Seagate ST1480A */
+ { 2, "1344", 175, 335 }, /* Seagate ST3144A */
+ { 6, "7 12", 110, 225 }, /* Maxtor 7213A */
+ { 30, "02F4", 145, 295 }, /* Conner 3204F */
+ { 2, "1302", 175, 335 }, /* Seagate ST3120A */
+ { 2, "2334", 145, 265 }, /* Seagate ST3243A */
+ { 2, "2338", 145, 275 }, /* Seagate ST3283A */
+ { 2, "3309", 145, 275 }, /* Seagate ST3390A */
+ { 2, "5305", 145, 275 }, /* Seagate ST3550A */
+ { 2, "4100", 175, 295 }, /* Seagate ST1400A */
+ { 2, "4110", 175, 295 }, /* Seagate ST1401A */
+ { 2, "6300", 135, 265 }, /* Seagate ST3600A */
+ { 2, "5300", 135, 265 }, /* Seagate ST3500A */
+ { 6, "7 31", 135, 225 }, /* Maxtor 7131 AT */
+ { 6, "7 43", 115, 265 }, /* Maxtor 7345 AT */
+ { 6, "7 42", 110, 255 }, /* Maxtor 7245 AT */
+ { 6, "3 04", 135, 265 }, /* Maxtor 340 AT */
+ { 6, "61 0", 135, 285 }, /* WD AC160 */
+ { 6, "1107", 135, 235 }, /* WD AC1170 */
+ { 6, "2101", 110, 220 }, /* WD AC1210 */
+ { 6, "4202", 135, 245 }, /* WD AC2420 */
+ { 6, "41 0", 175, 355 }, /* WD Caviar 140 */
+ { 6, "82 0", 175, 355 }, /* WD Caviar 280 */
+ { 8, "PL01", 175, 375 }, /* Quantum LP105 */
+ { 8, "PL25", 110, 295 }, /* Quantum LP525 */
+ { 10, "4S 2", 175, 385 }, /* Quantum ELS42 */
+ { 10, "8S 5", 175, 385 }, /* Quantum ELS85 */
+ { 10, "1S72", 175, 385 }, /* Quantum ELS127 */
+ { 10, "1S07", 175, 385 }, /* Quantum ELS170 */
+ { 8, "ZE42", 135, 295 }, /* Quantum EZ240 */
+ { 8, "ZE21", 175, 385 }, /* Quantum EZ127 */
+ { 8, "ZE58", 175, 385 }, /* Quantum EZ85 */
+ { 8, "ZE24", 175, 385 }, /* Quantum EZ42 */
+ { 27, "C036", 155, 325 }, /* Conner CP30064 */
+ { 27, "C038", 155, 325 }, /* Conner CP30084 */
+ { 6, "2205", 110, 255 }, /* WDC AC2250 */
+ { 2, " CHA", 140, 415 }, /* WDC AH series; WDC AH260, WDC */
+ { 2, " CLA", 140, 415 }, /* WDC AL series: WDC AL2120, 2170, */
+ { 4, "UC41", 140, 415 }, /* WDC CU140 */
+ { 6, "1207", 130, 275 }, /* WDC AC2170 */
+ { 6, "2107", 130, 275 }, /* WDC AC1270 */
+ { 6, "5204", 130, 275 }, /* WDC AC2540 */
+ { 30, "3004", 110, 235 }, /* Conner CP30340 */
+ { 30, "0345", 135, 255 }, /* Conner CP30544 */
+ { 12, "12A3", 175, 320 }, /* MAXTOR LXT-213A */
+ { 12, "43A0", 145, 240 }, /* MAXTOR LXT-340A */
+ { 6, "7 21", 180, 290 }, /* Maxtor 7120 AT */
+ { 6, "7 71", 135, 240 }, /* Maxtor 7170 AT */
+ { 12, "45\0000", 110, 205 }, /* MAXTOR MXT-540 */
+ { 8, "PL11", 180, 290 }, /* QUANTUM LP110A */
+ { 8, "OG21", 150, 275 }, /* QUANTUM GO120 */
+ { 12, "42A5", 175, 320 }, /* MAXTOR LXT-245A */
+ { 2, "2309", 175, 295 }, /* ST3290A */
+ { 2, "3358", 180, 310 }, /* ST3385A */
+ { 2, "6355", 180, 310 }, /* ST3655A */
+ { 2, "1900", 175, 270 }, /* ST9100A */
+ { 2, "1954", 175, 270 }, /* ST9145A */
+ { 2, "1909", 175, 270 }, /* ST9190AG */
+ { 2, "2953", 175, 270 }, /* ST9235A */
+ { 2, "1359", 175, 270 }, /* ST3195A */
+ { 24, "3R11", 175, 290 }, /* ALPS ELECTRIC Co.,LTD, DR311C */
+ { 0, "2M26", 175, 215 }, /* M262XT-0Ah */
+ { 4, "2253", 175, 300 }, /* HP C2235A */
+ { 4, "-32A", 145, 245 }, /* H3133-A2 */
+ { 30, "0326", 150, 270 }, /* Samsung Electronics 120MB */
+ { 30, "3044", 110, 195 }, /* Conner CFA340A */
+ { 30, "43A0", 110, 195 }, /* Conner CFA340A */
+ { -1, " ", 175, 415 } /* unknown disk name */
+};
Index: b/drivers/staging/ide-vlb/umc8672.c
===================================================================
--- /dev/null
+++ b/drivers/staging/ide-vlb/umc8672.c
@@ -0,0 +1,183 @@
+/*
+ * Copyright (C) 1995-1996 Linus Torvalds & author (see below)
+ */
+
+/*
+ * Principal Author/Maintainer: PODIEN@hml2.atlas.de (Wolfram Podien)
+ *
+ * This file provides support for the advanced features
+ * of the UMC 8672 IDE interface.
+ *
+ * Version 0.01 Initial version, hacked out of ide.c,
+ * and #include'd rather than compiled separately.
+ * This will get cleaned up in a subsequent release.
+ *
+ * Version 0.02 now configs/compiles separate from ide.c -ml
+ * Version 0.03 enhanced auto-tune, fix display bug
+ * Version 0.05 replace sti() with restore_flags() -ml
+ * add detection of possible race condition -ml
+ */
+
+/*
+ * VLB Controller Support from
+ * Wolfram Podien
+ * Rohoefe 3
+ * D28832 Achim
+ * Germany
+ *
+ * To enable UMC8672 support there must a lilo line like
+ * append="ide0=umc8672"...
+ * To set the speed according to the abilities of the hardware there must be a
+ * line like
+ * #define UMC_DRIVE0 11
+ * in the beginning of the driver, which sets the speed of drive 0 to 11 (there
+ * are some lines present). 0 - 11 are allowed speed values. These values are
+ * the results from the DOS speed test program supplied from UMC. 11 is the
+ * highest speed (about PIO mode 3)
+ */
+#define REALLY_SLOW_IO /* some systems can safely undef this */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/ioport.h>
+#include <linux/blkdev.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+
+#define DRV_NAME "umc8672"
+
+/*
+ * Default speeds. These can be changed with "auto-tune" and/or hdparm.
+ */
+#define UMC_DRIVE0 1 /* DOS measured drive speeds */
+#define UMC_DRIVE1 1 /* 0 to 11 allowed */
+#define UMC_DRIVE2 1 /* 11 = Fastest Speed */
+#define UMC_DRIVE3 1 /* In case of crash reduce speed */
+
+static u8 current_speeds[4] = {UMC_DRIVE0, UMC_DRIVE1, UMC_DRIVE2, UMC_DRIVE3};
+static const u8 pio_to_umc [5] = {0, 3, 7, 10, 11}; /* rough guesses */
+
+/* 0 1 2 3 4 5 6 7 8 9 10 11 */
+static const u8 speedtab [3][12] = {
+ {0x0f, 0x0b, 0x02, 0x02, 0x02, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x1},
+ {0x03, 0x02, 0x02, 0x02, 0x02, 0x02, 0x01, 0x01, 0x01, 0x01, 0x01, 0x1},
+ {0xff, 0xcb, 0xc0, 0x58, 0x36, 0x33, 0x23, 0x22, 0x21, 0x11, 0x10, 0x0}
+};
+
+static void out_umc(char port, char wert)
+{
+ outb_p(port, 0x108);
+ outb_p(wert, 0x109);
+}
+
+static inline u8 in_umc(char port)
+{
+ outb_p(port, 0x108);
+ return inb_p(0x109);
+}
+
+static void umc_set_speeds(u8 speeds[])
+{
+ int i, tmp;
+
+ outb_p(0x5A, 0x108); /* enable umc */
+
+ out_umc(0xd7, (speedtab[0][speeds[2]] | (speedtab[0][speeds[3]]<<4)));
+ out_umc(0xd6, (speedtab[0][speeds[0]] | (speedtab[0][speeds[1]]<<4)));
+ tmp = 0;
+ for (i = 3; i >= 0; i--)
+ tmp = (tmp << 2) | speedtab[1][speeds[i]];
+ out_umc(0xdc, tmp);
+ for (i = 0; i < 4; i++) {
+ out_umc(0xd0 + i, speedtab[2][speeds[i]]);
+ out_umc(0xd8 + i, speedtab[2][speeds[i]]);
+ }
+ outb_p(0xa5, 0x108); /* disable umc */
+
+ printk("umc8672: drive speeds [0 to 11]: %d %d %d %d\n",
+ speeds[0], speeds[1], speeds[2], speeds[3]);
+}
+
+static void umc_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+ ide_hwif_t *mate = hwif->mate;
+ unsigned long uninitialized_var(flags);
+ const u8 pio = drive->pio_mode - XFER_PIO_0;
+
+ printk("%s: setting umc8672 to PIO mode%d (speed %d)\n",
+ drive->name, pio, pio_to_umc[pio]);
+ if (mate)
+ spin_lock_irqsave(&mate->lock, flags);
+ if (mate && mate->handler) {
+ printk(KERN_ERR "umc8672: other interface is busy: exiting tune_umc()\n");
+ } else {
+ current_speeds[drive->name[2] - 'a'] = pio_to_umc[pio];
+ umc_set_speeds(current_speeds);
+ }
+ if (mate)
+ spin_unlock_irqrestore(&mate->lock, flags);
+}
+
+static const struct ide_port_ops umc8672_port_ops = {
+ .set_pio_mode = umc_set_pio_mode,
+};
+
+static const struct ide_port_info umc8672_port_info __initdata = {
+ .name = DRV_NAME,
+ .chipset = ide_umc8672,
+ .port_ops = &umc8672_port_ops,
+ .host_flags = IDE_HFLAG_NO_DMA,
+ .pio_mask = ATA_PIO4,
+};
+
+static int __init umc8672_probe(void)
+{
+ unsigned long flags;
+
+ if (!request_region(0x108, 2, "umc8672")) {
+ printk(KERN_ERR "umc8672: ports 0x108-0x109 already in use.\n");
+ return 1;
+ }
+ local_irq_save(flags);
+ outb_p(0x5A, 0x108); /* enable umc */
+ if (in_umc (0xd5) != 0xa0) {
+ local_irq_restore(flags);
+ printk(KERN_ERR "umc8672: not found\n");
+ release_region(0x108, 2);
+ return 1;
+ }
+ outb_p(0xa5, 0x108); /* disable umc */
+
+ umc_set_speeds(current_speeds);
+ local_irq_restore(flags);
+
+ return ide_legacy_device_add(&umc8672_port_info, 0);
+}
+
+static int probe_umc8672;
+
+module_param_named(probe, probe_umc8672, bool, 0);
+MODULE_PARM_DESC(probe, "probe for UMC8672 chipset");
+
+static int __init umc8672_init(void)
+{
+ if (probe_umc8672 == 0)
+ goto out;
+
+ if (umc8672_probe() == 0)
+ return 0;
+out:
+ return -ENODEV;
+}
+
+module_init(umc8672_init);
+
+MODULE_AUTHOR("Wolfram Podien");
+MODULE_DESCRIPTION("Support for UMC 8672 IDE chipset");
+MODULE_LICENSE("GPL");
^ permalink raw reply [flat|nested] 7+ messages in thread