From: Anton Vorontsov <avorontsov@ru.mvista.com>
To: Jeff Garzik <jgarzik@pobox.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>,
linux-ide@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH 11/11] ahci: Add platform driver
Date: Wed, 3 Mar 2010 20:17:50 +0300 [thread overview]
Message-ID: <20100303171750.GK12362@oksana.dev.rtsoft.ru> (raw)
In-Reply-To: <20100303171713.GA6322@oksana.dev.rtsoft.ru>
This can be used for AHCI-compatible interfaces implemented inside
System-On-Chip solutions, or AHCI devices connected via localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
drivers/ata/Kconfig | 9 ++
drivers/ata/Makefile | 1 +
drivers/ata/ahci_platform.c | 191 +++++++++++++++++++++++++++++++++++++++++
include/linux/ahci_platform.h | 29 ++++++
4 files changed, 230 insertions(+), 0 deletions(-)
create mode 100644 drivers/ata/ahci_platform.c
create mode 100644 include/linux/ahci_platform.h
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 365a9da..980a40a 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -71,6 +71,15 @@ config SATA_AHCI_PCI
help
This option enables support for PCI AHCI Serial ATA controllers.
+config SATA_AHCI_PLATFORM
+ tristate "Platform AHCI SATA support"
+ depends on SATA_AHCI
+ help
+ This option enables support for Platform AHCI Serial ATA
+ controllers.
+
+ If unsure, say N.
+
config SATA_SIL24
tristate "Silicon Image 3124/3132 SATA support"
depends on PCI
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index a438cef..e235321 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_ATA) += libata.o
obj-$(CONFIG_SATA_AHCI) += libahci.o
obj-$(CONFIG_SATA_AHCI_PCI) += ahci.o
+obj-$(CONFIG_SATA_AHCI_PLATFORM)+= ahci_platform.o
obj-$(CONFIG_SATA_SVW) += sata_svw.o
obj-$(CONFIG_ATA_PIIX) += ata_piix.o
obj-$(CONFIG_SATA_PROMISE) += sata_promise.o
diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
new file mode 100644
index 0000000..34f7b09
--- /dev/null
+++ b/drivers/ata/ahci_platform.c
@@ -0,0 +1,191 @@
+/*
+ * AHCI SATA platform driver
+ *
+ * Copyright 2004-2005 Red Hat, Inc.
+ * Jeff Garzik <jgarzik@pobox.com>
+ * Copyright 2010 MontaVista Software, LLC.
+ * Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/libata.h>
+#include <linux/platform_device.h>
+#include <linux/ahci_platform.h>
+#include "libahci.h"
+
+static int __init ahci_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ahci_platform_data *pdata = pdev->dev.platform_data;
+ struct ata_port_info pi = {
+ .flags = AHCI_FLAG_COMMON,
+ .pio_mask = ATA_PIO4,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &ahci_ops,
+ };
+ const struct ata_port_info *ppi[] = { &pi, NULL };
+ struct ahci_host_priv *hpriv;
+ struct ata_host *host;
+ struct resource *mem;
+ int irq;
+ int n_ports;
+ int i;
+ int rc;
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!mem) {
+ dev_err(dev, "no mmio space\n");
+ return -EINVAL;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq <= 0) {
+ dev_err(dev, "no irq\n");
+ return -EINVAL;
+ }
+
+ if (pdata && pdata->init) {
+ rc = pdata->init(dev);
+ if (rc)
+ return rc;
+ }
+
+ if (pdata && pdata->ata_port_info)
+ pi = *pdata->ata_port_info;
+
+ hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
+ if (!hpriv) {
+ rc = -ENOMEM;
+ goto err0;
+ }
+
+ hpriv->flags |= (unsigned long)pi.private_data;
+
+ hpriv->mmio = devm_ioremap(dev, mem->start, resource_size(mem));
+ if (!hpriv->mmio) {
+ dev_err(dev, "can't map %pR\n", mem);
+ rc = -ENOMEM;
+ goto err0;
+ }
+
+ ahci_save_initial_config(dev, hpriv,
+ pdata ? pdata->force_port_map : 0,
+ pdata ? pdata->mask_port_map : 0);
+
+ /* prepare host */
+ if (hpriv->cap & HOST_CAP_NCQ)
+ pi.flags |= ATA_FLAG_NCQ;
+
+ if (hpriv->cap & HOST_CAP_PMP)
+ pi.flags |= ATA_FLAG_PMP;
+
+ ahci_set_em_messages(hpriv, &pi);
+
+ /* CAP.NP sometimes indicate the index of the last enabled
+ * port, at other times, that of the last possible port, so
+ * determining the maximum port number requires looking at
+ * both CAP.NP and port_map.
+ */
+ n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
+
+ host = ata_host_alloc_pinfo(dev, ppi, n_ports);
+ if (!host) {
+ rc = -ENOMEM;
+ goto err0;
+ }
+
+ host->private_data = hpriv;
+
+ if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
+ host->flags |= ATA_HOST_PARALLEL_SCAN;
+ else
+ printk(KERN_INFO "ahci: SSS flag set, parallel bus scan disabled\n");
+
+ if (pi.flags & ATA_FLAG_EM)
+ ahci_reset_em(host);
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap = host->ports[i];
+
+ ata_port_desc(ap, "mmio %pR", mem);
+ ata_port_desc(ap, "port 0x%x", 0x100 + ap->port_no * 0x80);
+
+ /* set initial link pm policy */
+ ap->pm_policy = NOT_AVAILABLE;
+
+ /* set enclosure management message type */
+ if (ap->flags & ATA_FLAG_EM)
+ ap->em_message_type = ahci_em_messages;
+
+ /* disabled/not-implemented port */
+ if (!(hpriv->port_map & (1 << i)))
+ ap->ops = &ata_dummy_port_ops;
+ }
+
+ rc = ahci_reset_controller(host);
+ if (rc)
+ goto err0;
+
+ ahci_init_controller(host);
+ ahci_print_info(host, "platform");
+
+ rc = ata_host_activate(host, irq, ahci_interrupt, IRQF_SHARED,
+ &ahci_sht);
+ if (rc)
+ goto err0;
+
+ return 0;
+err0:
+ if (pdata && pdata->exit)
+ pdata->exit(dev);
+ return rc;
+}
+
+static int __devexit ahci_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct ahci_platform_data *pdata = pdev->dev.platform_data;
+
+ ata_host_detach(host);
+
+ if (pdata && pdata->exit)
+ pdata->exit(dev);
+
+ return 0;
+}
+
+static struct platform_driver ahci_driver = {
+ .probe = ahci_probe,
+ .remove = __devexit_p(ahci_remove),
+ .driver = {
+ .name = "ahci",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init ahci_init(void)
+{
+ return platform_driver_probe(&ahci_driver, ahci_probe);
+}
+module_init(ahci_init);
+
+static void __exit ahci_exit(void)
+{
+ platform_driver_unregister(&ahci_driver);
+}
+module_exit(ahci_exit);
+
+MODULE_DESCRIPTION("AHCI SATA platform driver");
+MODULE_AUTHOR("Anton Vorontsov <avorontsov@ru.mvista.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:ahci");
diff --git a/include/linux/ahci_platform.h b/include/linux/ahci_platform.h
new file mode 100644
index 0000000..f7dd576
--- /dev/null
+++ b/include/linux/ahci_platform.h
@@ -0,0 +1,29 @@
+/*
+ * AHCI SATA platform driver
+ *
+ * Copyright 2004-2005 Red Hat, Inc.
+ * Jeff Garzik <jgarzik@pobox.com>
+ * Copyright 2010 MontaVista Software, LLC.
+ * Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ */
+
+#ifndef _AHCI_PLATFORM_H
+#define _AHCI_PLATFORM_H
+
+struct device;
+struct ata_port_info;
+
+struct ahci_platform_data {
+ int (*init)(struct device *dev);
+ void (*exit)(struct device *dev);
+ const struct ata_port_info *ata_port_info;
+ unsigned int force_port_map;
+ unsigned int mask_port_map;
+};
+
+#endif /* _AHCI_PLATFORM_H */
--
1.7.0
prev parent reply other threads:[~2010-03-03 17:17 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-03-03 17:17 [PATCH 0/11] ahci: Add support for non-PCI devices Anton Vorontsov
2010-03-03 17:17 ` [PATCH 01/11] ahci: Get rid of host->iomap usage Anton Vorontsov
2010-03-03 18:45 ` Jeff Garzik
2010-03-03 18:49 ` Jeff Garzik
2010-03-03 17:17 ` [PATCH 02/11] ahci: Factor out PCI specifics from ahci_save_initial_config() Anton Vorontsov
2010-03-03 17:17 ` [PATCH 03/11] ahci: Get rid of pci_dev argument in ahci_save_initial_config() Anton Vorontsov
2010-03-03 17:17 ` [PATCH 04/11] ahci: Factor out PCI specifics from ahci_reset_controller() Anton Vorontsov
2010-03-03 17:17 ` [PATCH 05/11] ahci: Get rid of pci_dev argument in ahci_port_init() Anton Vorontsov
2010-03-03 17:17 ` [PATCH 06/11] ahci: Factor out PCI specifics from ahci_init_controller() Anton Vorontsov
2010-03-03 17:17 ` [PATCH 07/11] ahci: Factor out PCI specifics from ahci_print_info() Anton Vorontsov
2010-03-03 17:17 ` [PATCH 08/11] ahci: Introduce ahci_set_em_messages() Anton Vorontsov
2010-03-03 20:52 ` Jeff Garzik
2010-03-03 17:17 ` [PATCH 09/11] ahci: Move generic code into libahci Anton Vorontsov
2010-03-03 17:33 ` Sergei Shtylyov
2010-03-03 17:45 ` Anton Vorontsov
2010-03-03 18:43 ` Jeff Garzik
2010-03-03 21:58 ` Mark Lord
2010-03-03 17:17 ` [PATCH 10/11] ahci: Export generic AHCI symbols, turn libahci into a separate module Anton Vorontsov
2010-03-03 17:53 ` Sergei Shtylyov
2010-03-03 18:08 ` Anton Vorontsov
2010-03-03 18:14 ` Anton Vorontsov
2010-03-03 18:34 ` Jeff Garzik
2010-03-03 18:42 ` Anton Vorontsov
2010-03-03 17:17 ` Anton Vorontsov [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100303171750.GK12362@oksana.dev.rtsoft.ru \
--to=avorontsov@ru.mvista.com \
--cc=jgarzik@pobox.com \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=sshtylyov@mvista.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox