From: Sebastien Hinderer <Sebastien.Hinderer@ens-lyon.org>
To: "H. Peter Anvin" <hpa@zytor.com>
Cc: Samuel Thibault <Samuel.Thibault@ens-lyon.org>,
Andreas Mohr <andi@lisas.de>,
Thomas Gleixner <tglx@linutronix.de>,
Ingo Molnar <mingo@redhat.com>,
x86@kernel.org, Andrew Morton <akpm@linux-foundation.org>,
Frederic Weisbecker <fweisbec@gmail.com>,
Len Brown <len.brown@intel.com>,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH] x86: EuroBraille/Iris power off
Date: Thu, 26 Aug 2010 11:29:12 +0200 [thread overview]
Message-ID: <20100826092912.GA3336@pema> (raw)
In-Reply-To: <4C760FEE.1000309@zytor.com>
Hi again,
H. Peter Anvin (2010/08/25 23:55 -0700):
> > 00:00.0 Host bridge: Cyrix Corporation PCI Master
> > Flags: bus master, medium devsel, latency 0
> >
>
> Good grief ... these clowns didn't even program the subsystem ID? Could
> you verify with lspci -vv -n?
It's included below.
Shérab.
00:00.0 0600: 1078:0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 0200: 1282:9102 (rev 40)
Subsystem: 0291:8212
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 165 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at fedfe000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 08000000 [disabled] [size=256K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=160mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: dmfe
00:12.0 0601: 1078:0100 (rev 30)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 16 bytes
00:12.1 0680: 1078:0101
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 40012000 (32-bit, non-prefetchable) [size=256]
00:12.2 0101: 1078:0102 (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at 1400 [size=16]
Kernel driver in use: CS5530 IDE
00:12.3 0401: 1078:0103
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at 40011000 (32-bit, non-prefetchable) [size=128]
Kernel driver in use: CS5530_Audio
00:12.4 0300: 1078:0104 (prog-if 00 [VGA controller])
Subsystem: 1078:0001
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 40800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled]
00:13.0 0c03: 0e11:a0f8 (rev 06) (prog-if 10 [OHCI])
Subsystem: 0e11:a0f8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (20000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fedff000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
next prev parent reply other threads:[~2010-08-26 9:29 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-08-25 9:49 [PATCH] x86: EuroBraille/Iris power off Shérab
2010-08-25 16:12 ` Andreas Mohr
2010-08-25 21:12 ` Sebastien Hinderer
2010-08-25 21:19 ` H. Peter Anvin
2010-08-25 22:50 ` Samuel Thibault
2010-08-26 0:06 ` H. Peter Anvin
2010-08-26 0:19 ` Samuel Thibault
2010-08-26 6:45 ` Sebastien Hinderer
2010-08-26 6:55 ` H. Peter Anvin
2010-08-26 7:09 ` Andreas Mohr
2010-08-26 9:29 ` Sebastien Hinderer [this message]
2010-08-26 18:11 ` Len Brown
2010-08-26 21:08 ` Shérab
2010-08-26 21:16 ` H. Peter Anvin
2010-08-27 17:35 ` Shérab
2010-08-27 18:49 ` H. Peter Anvin
2010-08-27 22:27 ` Shérab
2010-08-29 20:59 ` Shérab
2010-09-13 10:07 ` Shérab
2010-09-13 15:10 ` Valdis.Kletnieks
2010-09-13 15:22 ` Samuel Thibault
2010-09-13 16:06 ` H. Peter Anvin
2010-09-13 16:12 ` Samuel Thibault
2010-09-14 1:45 ` Valdis.Kletnieks
2010-09-14 5:16 ` Shérab
2010-09-20 8:22 ` Shérab
2010-09-26 17:54 ` Shérab
2010-10-10 16:22 ` Shérab
2010-11-13 19:22 ` Shérab
2010-09-13 15:25 ` Shérab
2010-09-13 15:48 ` H. Peter Anvin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100826092912.GA3336@pema \
--to=sebastien.hinderer@ens-lyon.org \
--cc=Samuel.Thibault@ens-lyon.org \
--cc=akpm@linux-foundation.org \
--cc=andi@lisas.de \
--cc=fweisbec@gmail.com \
--cc=hpa@zytor.com \
--cc=len.brown@intel.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mingo@redhat.com \
--cc=tglx@linutronix.de \
--cc=x86@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox