From: Bob Tracy <rct@gherkin.frus.com>
To: linux-kernel@vger.kernel.org
Subject: [BUG] 3.0.0-rc2 usb mouse not working
Date: Tue, 14 Jun 2011 22:23:18 -0500 [thread overview]
Message-ID: <20110615032318.GA2575@gherkin.frus.com> (raw)
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain; charset=unknown-8bit, Size: 3466 bytes --]
Note: 3.0.0-rc1 hung during boot (right after parport initialization),
so the best I can do at the moment is say the bug first showed up after
2.6.39. Processor is an AMD K6-III/450.
Symptoms: Microsoft Intellimouse (corded USB optical) non-functional.
Red LED comes on when mouse is plugged in, but movement and
clicks are not seen.
"lsusb" segfaults :-(. "cat /proc/bus/usb/devices" gives the following
(the mouse and an APC UPS monitoring cable are plugged into the two
low-speed ports on the motherboard hub):
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.00
S: Manufacturer=Linux 3.0.0-rc2 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:08.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.00
S: Manufacturer=Linux 3.0.0-rc2 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:08.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.00
S: Manufacturer=Linux 3.0.0-rc2 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:07.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=051d ProdID=0002 Rev= 1.06
S: Manufacturer=American Power Conversion
S: Product=Back-UPS NS 1250 FW:7.g1 .D USB FW:g1
S: SerialNumber=JB0643005571
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 24mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 6 Ivl=10ms
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 4 Spd=1.5 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=045e ProdID=0039 Rev= 1.21
S: Manufacturer=Microsoft
S: Product=Microsoft IntelliMouse® Optical
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=10ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 4
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.00
S: Manufacturer=Linux 3.0.0-rc2 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:08.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
Unfortunately, I no longer have a working 2.6.39 kernel to compare
against, but the internal driver "plumbing" looks wrong: as mentioned
above, the mouse and the UPS cable are plugged into the low-speed
motherboard hub.
--Bob
next reply other threads:[~2011-06-15 3:51 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-06-15 3:23 Bob Tracy [this message]
2011-06-15 13:15 ` [BUG] 3.0.0-rc2 usb mouse not working Bob Tracy
2011-06-16 4:56 ` Bob Tracy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110615032318.GA2575@gherkin.frus.com \
--to=rct@gherkin.frus.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox