* [BUG] 3.0.0-rc2 usb mouse not working
@ 2011-06-15 3:23 Bob Tracy
2011-06-15 13:15 ` Bob Tracy
0 siblings, 1 reply; 3+ messages in thread
From: Bob Tracy @ 2011-06-15 3:23 UTC (permalink / raw)
To: linux-kernel
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain; charset=unknown-8bit, Size: 3466 bytes --]
Note: 3.0.0-rc1 hung during boot (right after parport initialization),
so the best I can do at the moment is say the bug first showed up after
2.6.39. Processor is an AMD K6-III/450.
Symptoms: Microsoft Intellimouse (corded USB optical) non-functional.
Red LED comes on when mouse is plugged in, but movement and
clicks are not seen.
"lsusb" segfaults :-(. "cat /proc/bus/usb/devices" gives the following
(the mouse and an APC UPS monitoring cable are plugged into the two
low-speed ports on the motherboard hub):
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.00
S: Manufacturer=Linux 3.0.0-rc2 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:08.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.00
S: Manufacturer=Linux 3.0.0-rc2 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:08.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.00
S: Manufacturer=Linux 3.0.0-rc2 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:07.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=051d ProdID=0002 Rev= 1.06
S: Manufacturer=American Power Conversion
S: Product=Back-UPS NS 1250 FW:7.g1 .D USB FW:g1
S: SerialNumber=JB0643005571
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 24mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 6 Ivl=10ms
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 4 Spd=1.5 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=045e ProdID=0039 Rev= 1.21
S: Manufacturer=Microsoft
S: Product=Microsoft IntelliMouse® Optical
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=10ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 4
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.00
S: Manufacturer=Linux 3.0.0-rc2 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:08.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
Unfortunately, I no longer have a working 2.6.39 kernel to compare
against, but the internal driver "plumbing" looks wrong: as mentioned
above, the mouse and the UPS cable are plugged into the low-speed
motherboard hub.
--Bob
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [BUG] 3.0.0-rc2 usb mouse not working
2011-06-15 3:23 [BUG] 3.0.0-rc2 usb mouse not working Bob Tracy
@ 2011-06-15 13:15 ` Bob Tracy
2011-06-16 4:56 ` Bob Tracy
0 siblings, 1 reply; 3+ messages in thread
From: Bob Tracy @ 2011-06-15 13:15 UTC (permalink / raw)
To: linux-kernel
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain; charset=unknown-8bit, Size: 12586 bytes --]
On Tue, Jun 14, 2011 at 10:23:18PM -0500, Bob Tracy wrote:
> Note: 3.0.0-rc1 hung during boot (right after parport initialization),
> so the best I can do at the moment is say the bug first showed up after
> 2.6.39. Processor is an AMD K6-III/450.
>
> Symptoms: Microsoft Intellimouse (corded USB optical) non-functional.
> Red LED comes on when mouse is plugged in, but movement and
> clicks are not seen.
3.0.0-rc3 followup... Mouse still broken, but at least "lsusb" is no
longer segfaulting. Here's "lsusb -v" output:
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.00
iManufacturer 3 Linux 3.0.0-rc3 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:08.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.00
iManufacturer 3 Linux 3.0.0-rc3 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:08.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 002 Device 003: ID 045e:0039 Microsoft Corp. IntelliMouse Optical
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x045e Microsoft Corp.
idProduct 0x0039 IntelliMouse Optical
bcdDevice 1.21
iManufacturer 1 Microsoft
iProduct 2 Microsoft IntelliMouse® Optical
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
** UNRECOGNIZED: 09 21 00 01 00 01 22 48 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
Bus 002 Device 002: ID 051d:0002 American Power Conversion Uninterruptible Power Supply
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x051d American Power Conversion
idProduct 0x0002 Uninterruptible Power Supply
bcdDevice 1.06
iManufacturer 3 American Power Conversion
iProduct 1 Back-UPS NS 1250 FW:7.g1 .D USB FW:g1
iSerial 2 JB0643005571
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 24mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
** UNRECOGNIZED: 09 21 10 01 21 01 22 06 04
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0006 1x 6 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.00
iManufacturer 3 Linux 3.0.0-rc3 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:07.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0303 lowspeed power enable connect
Port 2: 0000.0303 lowspeed power enable connect
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 3.00
iManufacturer 3 Linux 3.0.0-rc3 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:08.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
--Bob
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [BUG] 3.0.0-rc2 usb mouse not working
2011-06-15 13:15 ` Bob Tracy
@ 2011-06-16 4:56 ` Bob Tracy
0 siblings, 0 replies; 3+ messages in thread
From: Bob Tracy @ 2011-06-16 4:56 UTC (permalink / raw)
To: linux-kernel
On Wed, Jun 15, 2011 at 08:15:44AM -0500, Bob Tracy wrote:
> On Tue, Jun 14, 2011 at 10:23:18PM -0500, Bob Tracy wrote:
> > Note: 3.0.0-rc1 hung during boot (right after parport initialization),
> > so the best I can do at the moment is say the bug first showed up after
> > 2.6.39. Processor is an AMD K6-III/450.
> >
> > Symptoms: Microsoft Intellimouse (corded USB optical) non-functional.
> > Red LED comes on when mouse is plugged in, but movement and
> > clicks are not seen.
To make a long story short, the required "usbhid" module is not being
loaded automatically in 3.0-rcX as it was in 2.6.39 and earlier kernels.
A simple "modprobe usbhid" got the mouse working again.
--Bob
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2011-06-16 4:56 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-06-15 3:23 [BUG] 3.0.0-rc2 usb mouse not working Bob Tracy
2011-06-15 13:15 ` Bob Tracy
2011-06-16 4:56 ` Bob Tracy
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox