From: Wu Fengguang <fengguang.wu@intel.com>
To: Daniel Vetter <daniel@ffwll.ch>
Cc: Keith Packard <keithp@keithp.com>, Takashi Iwai <tiwai@suse.de>,
"intel-gfx@lists.freedesktop..."
<intel-gfx@lists.freedesktop.org>, Michal Marek <mmarek@suse.com>,
LKML <linux-kernel@vger.kernel.org>,
Robert Lemaire <rlemaire@suse.com>
Subject: [PATCH][rebased] drm/i915: set AUD_CONFIG N_value_index for DisplayPort
Date: Sun, 29 Jan 2012 12:44:24 +0800 [thread overview]
Message-ID: <20120129044423.GA26244@localhost> (raw)
In-Reply-To: <20120117102203.GC4093@phenom.ffwll.local>
It should be programmed to "0" for HDMI or "1" for DisplayPort.
This enables DisplayPort audio for
- HP EliteBook 8460p
(whose BIOS does not set the N_value_index bit for us)
- DisplayPort monitor hot plugged after boot
(otherwise most BIOS will fill the N_value_index bit for us)
Tested-by: Robert Lemaire <rlemaire@suse.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
---
drivers/gpu/drm/i915/i915_reg.h | 12 ++++++++++++
drivers/gpu/drm/i915/intel_display.c | 8 +++++++-
2 files changed, 19 insertions(+), 1 deletion(-)
> I've tried to apply this patch but it has a conflict in i915_reg.h (with
> the SOL reset stuff). Care to rebase and resend? Also, git patches as
> produced by git format-patch highly preferred.
Daniel, this is now based on linux-next. I use quilt, hope it also
works for you :)
--- linux-next.orig/drivers/gpu/drm/i915/i915_reg.h 2012-01-07 20:47:34.000000000 +0800
+++ linux-next/drivers/gpu/drm/i915/i915_reg.h 2012-01-29 12:37:31.000000000 +0800
@@ -3742,4 +3742,16 @@
*/
#define GEN7_SO_WRITE_OFFSET(n) (0x5280 + (n) * 4)
+#define IBX_AUD_CONFIG_A 0xe2000
+#define CPT_AUD_CONFIG_A 0xe5000
+#define AUD_CONFIG_N_VALUE_INDEX (1 << 29)
+#define AUD_CONFIG_N_PROG_ENABLE (1 << 28)
+#define AUD_CONFIG_UPPER_N_SHIFT 20
+#define AUD_CONFIG_UPPER_N_VALUE (0xff << 20)
+#define AUD_CONFIG_LOWER_N_SHIFT 4
+#define AUD_CONFIG_LOWER_N_VALUE (0xfff << 4)
+#define AUD_CONFIG_PIXEL_CLOCK_HDMI_SHIFT 16
+#define AUD_CONFIG_PIXEL_CLOCK_HDMI (0xf << 16)
+#define AUD_CONFIG_DISABLE_NCTS (1 << 3)
+
#endif /* _I915_REG_H_ */
--- linux-next.orig/drivers/gpu/drm/i915/intel_display.c 2012-01-29 12:23:17.000000000 +0800
+++ linux-next/drivers/gpu/drm/i915/intel_display.c 2012-01-29 12:37:31.000000000 +0800
@@ -6072,15 +6072,18 @@ static void ironlake_write_eld(struct dr
uint32_t i;
int len;
int hdmiw_hdmiedid;
+ int aud_config;
int aud_cntl_st;
int aud_cntrl_st2;
if (HAS_PCH_IBX(connector->dev)) {
hdmiw_hdmiedid = IBX_HDMIW_HDMIEDID_A;
+ aud_config = IBX_AUD_CONFIG_A;
aud_cntl_st = IBX_AUD_CNTL_ST_A;
aud_cntrl_st2 = IBX_AUD_CNTL_ST2;
} else {
hdmiw_hdmiedid = CPT_HDMIW_HDMIEDID_A;
+ aud_config = CPT_AUD_CONFIG_A;
aud_cntl_st = CPT_AUD_CNTL_ST_A;
aud_cntrl_st2 = CPT_AUD_CNTRL_ST2;
}
@@ -6088,6 +6091,7 @@ static void ironlake_write_eld(struct dr
i = to_intel_crtc(crtc)->pipe;
hdmiw_hdmiedid += i * 0x100;
aud_cntl_st += i * 0x100;
+ aud_config += i * 0x100;
DRM_DEBUG_DRIVER("ELD on pipe %c\n", pipe_name(i));
@@ -6107,7 +6111,9 @@ static void ironlake_write_eld(struct dr
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT)) {
DRM_DEBUG_DRIVER("ELD: DisplayPort detected\n");
eld[5] |= (1 << 2); /* Conn_Type, 0x1 = DisplayPort */
- }
+ I915_WRITE(aud_config, AUD_CONFIG_N_VALUE_INDEX); /* 0x1 = DP */
+ } else
+ I915_WRITE(aud_config, 0);
if (intel_eld_uptodate(connector,
aud_cntrl_st2, eldv,
next prev parent reply other threads:[~2012-01-29 4:54 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-01-09 13:17 [PATCH] drm/i915: set AUD_CONFIG N_value_index for DisplayPort Wu Fengguang
2012-01-09 17:22 ` Keith Packard
2012-01-10 5:45 ` Wu Fengguang
2012-01-12 17:33 ` Keith Packard
2012-01-16 8:02 ` Wu Fengguang
2012-01-16 20:26 ` [Intel-gfx] " Daniel Vetter
2012-01-16 20:44 ` Keith Packard
2012-01-16 23:08 ` Wu Fengguang
2012-01-16 23:15 ` Keith Packard
2012-01-17 10:22 ` Daniel Vetter
2012-01-29 4:44 ` Wu Fengguang [this message]
2012-01-29 12:12 ` [PATCH][rebased] " Daniel Vetter
2012-01-29 13:23 ` Wu Fengguang
2012-01-29 15:14 ` Daniel Vetter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120129044423.GA26244@localhost \
--to=fengguang.wu@intel.com \
--cc=daniel@ffwll.ch \
--cc=intel-gfx@lists.freedesktop.org \
--cc=keithp@keithp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mmarek@suse.com \
--cc=rlemaire@suse.com \
--cc=tiwai@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).