From: Samuel Ortiz <sameo@linux.intel.com>
To: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: patches@opensource.wolfsonmicro.com, linux-kernel@vger.kernel.org
Subject: Re: [PATCH 0/15] arizona updates for v3.10
Date: Mon, 8 Apr 2013 16:31:03 +0200 [thread overview]
Message-ID: <20130408143103.GB21256@zurbaran> (raw)
In-Reply-To: <20130408101951.GD9243@opensource.wolfsonmicro.com>
Hi Mark,
On Mon, Apr 08, 2013 at 11:19:51AM +0100, Mark Brown wrote:
> On Mon, Apr 08, 2013 at 11:04:10AM +0100, Mark Brown wrote:
>
> > patch series... I'm just re-tagging and re-pushing but were you testing
> > both serieses together?
>
> OK, the mirrors seem to have the rebase now. New pull request:
>
> The following changes since commit 31880c37c11e28cb81c70757e38392b42e695dc6:
>
> Linux 3.9-rc6 (2013-04-07 20:49:54 -0700)
>
> are available in the git repository at:
>
> git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc.git tags/mfd-arizona-3.10
>
> for you to fetch changes up to 031eb8d52ecbe417cf778fba2d49bee90a078648:
>
> mfd: wm5102: Don't wait for boot when boot sequencer is disabled (2013-04-08 11:12:04 +0100)
>
> ----------------------------------------------------------------
> mfd: arizona: Updates for v3.10
>
> This is really a few separate topics which I can split out if required:
>
> - WM5102 updates to improve robustness
> - Improved support for interoperation with edge triggered interrupt
> controllers
> - Support for some unusual clocking configurations
> - A couple small single patch updates and fixes
Thanks, all 19 patches applied now. Everything builds fine on my side.
The culprit for the missing arizona_of_get_core_pdata was "mfd: Add device
tree bindings for Arizona class devices", not the above branch.
Cheers,
Samuel.
--
Intel Open Source Technology Centre
http://oss.intel.com/
prev parent reply other threads:[~2013-04-08 14:31 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-04-01 17:27 [PATCH 0/15] arizona updates for v3.10 Mark Brown
2013-04-01 17:27 ` [PATCH 01/15] mfd: arizona: Disable all wake sources by default Mark Brown
2013-04-01 17:27 ` [PATCH 02/15] mfd: arizona: Clarify error message for failed primary IRQ request Mark Brown
2013-04-01 17:28 ` [PATCH 03/15] mfd: arizona: Basic support for edge triggered IRQs Mark Brown
2013-04-01 17:28 ` [PATCH 04/15] mfd: arizona: Allow GPIO to be specified for IRQ line Mark Brown
2013-04-01 17:28 ` [PATCH 05/15] mfd: arizona: Try to use interrupt flags from interrupt controller Mark Brown
2013-04-01 17:28 ` [PATCH 06/15] mfd: arizona: Support configuring MICBIASes into bypass mode Mark Brown
2013-04-01 17:28 ` [PATCH 07/15] mfd: wm5102: Update patch for latest evaluation Mark Brown
2013-04-01 17:28 ` [PATCH 08/15] mfd: arizona: Fully support the use of MCLK1 as the 32kHz clock source Mark Brown
2013-04-01 17:28 ` [PATCH 09/15] mfd: arizona: Unconditionally enable 32kHz clock Mark Brown
2013-04-01 17:28 ` [PATCH 10/15] mfd: wm5102: Only use the lowest three bits of device revision Mark Brown
2013-04-01 17:28 ` [PATCH 11/15] mfd: wm5102: Manually apply register patch Mark Brown
2013-04-01 17:28 ` [PATCH 12/15] mfd: arizona: Factor out register polling Mark Brown
2013-04-01 17:28 ` [PATCH 13/15] mfd: arizona: Add a hardware patch mechanism Mark Brown
2013-04-01 17:28 ` [PATCH 14/15] mfd: wm5102: Deactivate standard boot sequence Mark Brown
2013-04-01 17:28 ` [PATCH 15/15] mfd: wm5102: Update defaults to match patch Mark Brown
2013-04-03 18:04 ` [PATCH 0/15] arizona updates for v3.10 Mark Brown
2013-04-03 18:05 ` [PATCH 1/3] mfd: arizona: Hold device in reset while ramping supplies Mark Brown
2013-04-03 18:05 ` [PATCH 2/3] mfd: arizona: Wait for internal clocks to startup after reset Mark Brown
2013-04-03 18:05 ` [PATCH 3/3] mfd: wm5102: Don't wait for boot when boot sequencer is disabled Mark Brown
2013-04-08 9:25 ` [PATCH 0/15] arizona updates for v3.10 Samuel Ortiz
2013-04-08 9:38 ` Samuel Ortiz
2013-04-08 10:04 ` Mark Brown
2013-04-08 10:19 ` Mark Brown
2013-04-08 14:31 ` Samuel Ortiz [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20130408143103.GB21256@zurbaran \
--to=sameo@linux.intel.com \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=linux-kernel@vger.kernel.org \
--cc=patches@opensource.wolfsonmicro.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox