Re: [PATCH v4] regulator: pfuze100: add pfuze100 regulator driver

Robin Gong
2013-07-22T10:35:06Z

On Mon, Jul 22, 2013 at 05:11:00PM +0800, Shawn Guo wrote:
> On Sun, Jul 21, 2013 at 05:17:27PM +0800, Robin Gong wrote:
> > Add pfuze100 regulator driver.
> >
> > Signed-off-by: Robin Gong <b38343@freescale.com>
> > ---
> > .../devicetree/bindings/regulator/pfuze100.txt | 113 +++++
> > drivers/regulator/Kconfig | 7 +
> > drivers/regulator/Makefile | 1 +
> > drivers/regulator/pfuze100-regulator.c | 462 ++++++++++++++++++++
> > include/linux/regulator/pfuze100.h | 44 ++
> > 5 files changed, 627 insertions(+), 0 deletions(-)
> > create mode 100644 Documentation/devicetree/bindings/regulator/pfuze100.txt
> > create mode 100644 drivers/regulator/pfuze100-regulator.c
> > create mode 100644 include/linux/regulator/pfuze100.h
> >
> > diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt
> > new file mode 100644
> > index 0000000..22e1a48
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt
> > @@ -0,0 +1,113 @@
> > +PFUZE100 family of regulators
> > +
> > +Required properties:
> > +- compatible: "fsl,pfuze100"
> > +- reg: I2C slave address
> > +- regulators: This is the list of child nodes that specify the regulator
> > + initialization data for defined regulators. Please refer to below doc
> > + Documentation/devicetree/bindings/regulator/regulator.txt.
>
> "regulators" is not a property but a sub-node.
>
> > +
> > + The valid names for regulators are:
> > + sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6
> > +
> > +Each regulator is defined using the standard binding for regulators.
> > +
> > +Example:
> > +
> > + pmic: pfuze100@08 {
> > + compatible = "fsl,pfuze100";
> > + reg = <0x08>;
> > +
> > + regulators {
> > + sw1a_reg: sw1ab {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <1875000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <6250>;
> > + };
> > +
> > + sw1c_reg: sw1c {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <1875000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw2_reg: sw2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw3a_reg: sw3a {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1975000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw3b_reg: sw3b {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1975000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw4_reg: sw4 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + };
> > +
> > + swbst_reg: swbst {
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5150000>;
> > + };
> > +
> > + snvs_reg: vsnvs {
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + vref_reg: vrefddr {
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + vgen1_reg: vgen1 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1550000>;
> > + };
> > +
> > + vgen2_reg: vgen2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1550000>;
> > + };
> > +
> > + vgen3_reg: vgen3 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + };
> > +
> > + vgen4_reg: vgen4 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen5_reg: vgen5 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen6_reg: vgen6 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > + };
> > + };
> > diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
> > index f1e6ad9..f913172 100644
> > --- a/drivers/regulator/Kconfig
> > +++ b/drivers/regulator/Kconfig
> > @@ -158,6 +158,13 @@ config REGULATOR_MC13892
> > Say y here to support the regulators found on the Freescale MC13892
> > PMIC.
> >
> > +config REGULATOR_PFUZE100
> > + tristate "Support regulators on Freescale PFUZE100 PMIC"
> > + depends on I2C
> > + help
> > + Say y here to support the regulators found on the Freescale PFUZE100
> > + PMIC.
> > +
> > config REGULATOR_ISL6271A
> > tristate "Intersil ISL6271A Power regulator"
> > depends on I2C
> > diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
> > index ba4a3cf..ad62524 100644
> > --- a/drivers/regulator/Makefile
> > +++ b/drivers/regulator/Makefile
> > @@ -45,6 +45,7 @@ obj-$(CONFIG_REGULATOR_MAX77693) += max77693.o
> > obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
> > obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
> > obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
> > +obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
> > obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
> > obj-$(CONFIG_REGULATOR_TPS51632) += tps51632-regulator.o
> > obj-$(CONFIG_REGULATOR_PCAP) += pcap-regulator.o
> > diff --git a/drivers/regulator/pfuze100-regulator.c b/drivers/regulator/pfuze100-regulator.c
> > new file mode 100644
> > index 0000000..fd259ef
> > --- /dev/null
> > +++ b/drivers/regulator/pfuze100-regulator.c
> > @@ -0,0 +1,462 @@
> > +/*
> > + * Copyright (C) 2011-2013 Freescale Semiconductor, Inc. All Rights Reserved.
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * You should have received a copy of the GNU General Public License
> > + * along with this program; if not, write to the Free Software
> > + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
> > + */
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/init.h>
> > +#include <linux/err.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/regulator/of_regulator.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regulator/driver.h>
> > +#include <linux/regulator/machine.h>
> > +#include <linux/regulator/pfuze100.h>
> > +#include <linux/i2c.h>
> > +#include <linux/slab.h>
> > +#include <linux/regmap.h>
> > +
> > +
>
> One blank line.
>
> > +#define PFUZE_NUMREGS 128
> > +#define PFUZE100_VOL_OFFSET 0
> > +#define PFUZE100_STANDBY_OFFSET 1
> > +#define PFUZE100_MODE_OFFSET 3
> > +#define PFUZE100_CONF_OFFSET 4
> > +
> > +#define PFUZE100_DEVICEID 0x0
> > +#define PFUZE100_REVID 0x3
> > +#define PFUZE100_FABID 0x3
> > +
> > +#define PFUZE100_SW1ABVOL 0x20
> > +#define PFUZE100_SW1CVOL 0x2e
> > +#define PFUZE100_SW2VOL 0x35
> > +#define PFUZE100_SW3AVOL 0x3c
> > +#define PFUZE100_SW3BVOL 0x43
> > +#define PFUZE100_SW4VOL 0x4a
> > +#define PFUZE100_SWBSTCON1 0x66
> > +#define PFUZE100_VREFDDRCON 0x6a
> > +#define PFUZE100_VSNVSVOL 0x6b
> > +#define PFUZE100_VGEN1VOL 0x6c
> > +#define PFUZE100_VGEN2VOL 0x6d
> > +#define PFUZE100_VGEN3VOL 0x6e
> > +#define PFUZE100_VGEN4VOL 0x6f
> > +#define PFUZE100_VGEN5VOL 0x70
> > +#define PFUZE100_VGEN6VOL 0x71
> > +
> > +struct pfuze_regulator {
> > + struct regulator_desc desc;
> > + unsigned char stby_reg;
> > + unsigned char stby_mask;
> > +};
> > +
> > +struct pfuze_chip {
> > + struct regmap *regmap;
> > + struct device *dev;
> > + struct pfuze_regulator regulator_descs[PFUZE100_MAX_REGULATOR];
> > + struct regulator_dev *regulators[PFUZE100_MAX_REGULATOR];
> > +};
> > +
> > +static const int pfuze100_swbst[] = {
> > + 5000000, 5050000, 5100000, 5150000,
> > +};
> > +
> > +static const int pfuze100_vsnvs[] = {
> > + 1000000, 1100000, 1200000, 1300000, 1500000, 1800000, 3000000,
> > +};
> > +
> > +static const struct i2c_device_id pfuze_device_id[] = {
> > + {.name = "pfuze100"},
> > + {},
> > +};
> > +MODULE_DEVICE_TABLE(i2c, pfuze_device_id);
> > +
> > +static const struct of_device_id pfuze_dt_ids[] = {
> > + { .compatible = "fsl,pfuze100" },
> > + {},
> > +};
> > +MODULE_DEVICE_TABLE(of, pfuze_dt_ids);
> > +
> > +static int pfuze100_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
> > +{
> > + struct pfuze_chip *pfuze100 = rdev_get_drvdata(rdev);
> > + int id = rdev->desc->id;
> > + unsigned int val, ramp_bits, reg;
> > + int ret;
> > +
> > + if (id < PFUZE100_SWBST) {
> > + if (id == PFUZE100_SW1AB)
> > + reg = PFUZE100_SW1ABVOL;
> > + else
> > + reg = PFUZE100_SW1CVOL + (id - PFUZE100_SW1C) * 7;
> > + regmap_read(pfuze100->regmap, reg, &val);
> > +
> > + if (id <= PFUZE100_SW1C)
> > + ramp_delay = 25000 / (2 * ramp_delay);
> > + else if (val & 0x40)
> > + ramp_delay = 50000 / (4 * ramp_delay);
> > + else
> > + ramp_delay = 25000 / (2 * ramp_delay);
> > +
> > + ramp_bits = (ramp_delay >> 1) - (ramp_delay >> 3);
> > + ret = regmap_update_bits(pfuze100->regmap, reg + 4 , 0xc0,
> > + ramp_bits << 6);
> > + if (ret < 0)
> > + dev_err(pfuze100->dev, "ramp failed, err %d\n", ret);
> > + } else
> > + ret = -EACCES;
> > +
> > + return ret;
> > +}
> > +
> > +static struct regulator_ops pfuze100_ldo_regulator_ops = {
> > + .enable = regulator_enable_regmap,
> > + .disable = regulator_disable_regmap,
> > + .is_enabled = regulator_is_enabled_regmap,
> > + .list_voltage = regulator_list_voltage_linear,
> > + .set_voltage_sel = regulator_set_voltage_sel_regmap,
> > + .get_voltage_sel = regulator_get_voltage_sel_regmap,
> > +};
> > +
> > +static struct regulator_ops pfuze100_fixed_regulator_ops = {
> > + .list_voltage = regulator_list_voltage_linear,
> > +};
> > +
> > +static struct regulator_ops pfuze100_sw_regulator_ops = {
> > + .list_voltage = regulator_list_voltage_linear,
> > + .set_voltage_sel = regulator_set_voltage_sel_regmap,
> > + .get_voltage_sel = regulator_get_voltage_sel_regmap,
> > + .set_voltage_time_sel = regulator_set_voltage_time_sel,
> > + .set_ramp_delay = pfuze100_set_ramp_delay,
> > +};
> > +
> > +static struct regulator_ops pfuze100_swb_regulator_ops = {
> > + .list_voltage = regulator_list_voltage_table,
> > + .set_voltage_sel = regulator_set_voltage_sel_regmap,
> > + .get_voltage_sel = regulator_get_voltage_sel_regmap,
> > +
> > +};
> > +
> > +#define PFUZE100_FIXED_REG(_name, base, voltage) \
> > +{ \
> > + [PFUZE100_ ## _name] = { \
> > + .desc = { \
> > + .name = #_name, \
> > + .n_voltages = 1, \
> > + .ops = &pfuze100_fixed_regulator_ops, \
> > + .type = REGULATOR_VOLTAGE, \
> > + .id = PFUZE100_ ## _name, \
> > + .owner = THIS_MODULE, \
> > + .min_uV = (voltage), \
> > + .enable_reg = (base), \
> > + .enable_mask = 0x10, \
> > + }, \
> > + } \
> > +}
> > +
> > +#define PFUZE100_SW_REG(_name, base, min, max, step) \
> > +{ \
> > + [PFUZE100_ ## _name] = { \
> > + .desc = { \
> > + .name = #_name,\
> > + .n_voltages = ((max) - (min)) / (step) + 1, \
> > + .ops = &pfuze100_sw_regulator_ops, \
> > + .type = REGULATOR_VOLTAGE, \
> > + .id = PFUZE100_ ## _name, \
> > + .owner = THIS_MODULE, \
> > + .min_uV = (min), \
> > + .uV_step = (step), \
> > + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
> > + .vsel_mask = 0x3f, \
> > + }, \
> > + .stby_reg = (base) + PFUZE100_STANDBY_OFFSET, \
> > + .stby_mask = 0x3f, \
> > + } \
> > +}
> > +
> > +#define PFUZE100_SWB_REG(_name, base, mask, voltages) \
> > +{ \
> > + [PFUZE100_ ## _name] = { \
> > + .desc = { \
> > + .name = #_name, \
> > + .n_voltages = ARRAY_SIZE(voltages), \
> > + .ops = &pfuze100_swb_regulator_ops, \
> > + .type = REGULATOR_VOLTAGE, \
> > + .id = PFUZE100_ ## _name, \
> > + .owner = THIS_MODULE, \
> > + .volt_table = voltages, \
> > + .vsel_reg = (base), \
> > + .vsel_mask = (mask), \
> > + }, \
> > + } \
> > +}
> > +
> > +#define PFUZE100_VGEN_REG(_name, base, min, max, step) \
> > +{ \
> > + [PFUZE100_ ## _name] = { \
> > + .desc = { \
> > + .name = #_name, \
> > + .n_voltages = ((max) - (min)) / (step) + 1, \
> > + .ops = &pfuze100_ldo_regulator_ops, \
> > + .type = REGULATOR_VOLTAGE, \
> > + .id = PFUZE100_ ## _name, \
> > + .owner = THIS_MODULE, \
> > + .min_uV = (min), \
> > + .uV_step = (step), \
> > + .vsel_reg = (base), \
> > + .vsel_mask = 0xf, \
> > + .enable_reg = (base), \
> > + .enable_mask = 0x10, \
> > + }, \
> > + .stby_reg = (base), \
> > + .stby_mask = 0x20, \
> > + } \
> > +}
> > +
> > +static struct pfuze_regulator pfuze100_regulators[] = {
> > + PFUZE100_SW_REG(SW1AB, PFUZE100_SW1ABVOL, 300000, 1875000, 25000),
> > + PFUZE100_SW_REG(SW1C, PFUZE100_SW1CVOL, 300000, 1875000, 25000),
> > + PFUZE100_SW_REG(SW2, PFUZE100_SW2VOL, 400000, 1975000, 25000),
> > + PFUZE100_SW_REG(SW3A, PFUZE100_SW3AVOL, 400000, 1975000, 25000),
> > + PFUZE100_SW_REG(SW3B, PFUZE100_SW3BVOL, 400000, 1975000, 25000),
> > + PFUZE100_SW_REG(SW4, PFUZE100_SW4VOL, 400000, 1975000, 25000),
> > + PFUZE100_SWB_REG(SWBST, PFUZE100_SWBSTCON1, 0x3 , pfuze100_swbst),
> > + PFUZE100_SWB_REG(VSNVS, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
> > + PFUZE100_FIXED_REG(VREFDDR, PFUZE100_VREFDDRCON, 750000),
> > + PFUZE100_VGEN_REG(VGEN1, PFUZE100_VGEN1VOL, 800000, 1550000, 50000),
> > + PFUZE100_VGEN_REG(VGEN2, PFUZE100_VGEN2VOL, 800000, 1550000, 50000),
> > + PFUZE100_VGEN_REG(VGEN3, PFUZE100_VGEN3VOL, 1800000, 3300000, 100000),
> > + PFUZE100_VGEN_REG(VGEN4, PFUZE100_VGEN4VOL, 1800000, 3300000, 100000),
> > + PFUZE100_VGEN_REG(VGEN5, PFUZE100_VGEN5VOL, 1800000, 3300000, 100000),
> > + PFUZE100_VGEN_REG(VGEN6, PFUZE100_VGEN6VOL, 1800000, 3300000, 100000),
> > +};
> > +
> > +#ifdef CONFIG_OF
> > +static struct of_regulator_match pfuze100_matches[] = {
> > + { .name = "sw1ab", },
> > + { .name = "sw1c", },
> > + { .name = "sw2", },
> > + { .name = "sw3a", },
> > + { .name = "sw3b", },
> > + { .name = "sw4", },
> > + { .name = "swbst", },
> > + { .name = "vsnvs", },
> > + { .name = "vrefddr", },
> > + { .name = "vgen1", },
> > + { .name = "vgen2", },
> > + { .name = "vgen3", },
> > + { .name = "vgen4", },
> > + { .name = "vgen5", },
> > + { .name = "vgen6", },
> > +};
> > +
> > +static int pfuze_parse_regulators_dt(struct pfuze_chip *chip)
> > +{
> > + struct device *dev = chip->dev;
> > + struct device_node *parent;
> > + int ret;
> > +
> > + of_node_get(dev->parent->of_node);
> > + parent = of_find_node_by_name(dev->parent->of_node, "regulators");
> > + if (!parent) {
> > + dev_err(dev, "regulators node not found\n");
> > + return -EINVAL;
>
> So you leave dev->parent->of_node unbalanced.
>
Seems of_find_node_by_name will of_node_put the parent node.
> > + }
> > +
> > + ret = of_regulator_match(dev, parent, pfuze100_matches,
> > + ARRAY_SIZE(pfuze100_matches));
> > +
> > + of_node_put(dev->parent->of_node);
>
> This could be move before of_regulator_match(), right?
>
> > + if (ret < 0) {
> > + dev_err(dev, "Error parsing regulator init data: %d\n",
> > + ret);
> > + return ret;
> > + }
> > +
>
> The kernel doc of function of_find_node_by_name() suggests you need a
> of_node_put() call to put the node you get from there.
>
Good point, should modify of_node_put(dev->parent->of_node) to
of_node_put(parent).
> > + return 0;
> > +}
> > +
> > +static inline struct regulator_init_data *match_init_data(int index)
> > +{
> > + return pfuze100_matches[index].init_data;
> > +}
> > +
> > +static inline struct device_node *match_of_node(int index)
> > +{
> > + return pfuze100_matches[index].of_node;
> > +}
> > +#else
> > +static int pfuze_parse_regulators_dt(struct pfuze_chip *chip)
> > +{
> > + return NULL;
> > +}
> > +
> > +static inline struct regulator_init_data *match_init_data(int index)
> > +{
> > + return NULL;
> > +}
> > +
> > +static inline struct device_node *match_of_node(int index)
> > +{
> > + return NULL;
> > +}
> > +#endif
> > +
> > +static int pfuze_identify(struct pfuze_chip *pfuze_chip)
> > +{
> > + unsigned int value;
> > + int ret;
> > +
> > + ret = regmap_read(pfuze_chip->regmap, PFUZE100_DEVICEID, &value);
> > + if (ret)
> > + return ret;
> > +
> > + if (value & 0x0f) {
> > + dev_warn(pfuze_chip->dev, "Illegal ID: %x\n", value);
> > + return -ENODEV;
> > + }
> > +
> > + ret = regmap_read(pfuze_chip->regmap, PFUZE100_REVID, &value);
> > + if (ret)
> > + return ret;
> > + dev_info(pfuze_chip->dev,
> > + "Full lay: %x, Metal lay: %x\n",
> > + (value & 0xf0) >> 4, value & 0x0f);
> > +
> > + ret = regmap_read(pfuze_chip->regmap, PFUZE100_FABID, &value);
> > + if (ret)
> > + return ret;
> > + dev_info(pfuze_chip->dev, "FAB: %x, FIN: %x\n",
> > + (value & 0xc) >> 2, value & 0x3);
> > +
> > + return 0;
> > +}
> > +
> > +static struct regmap_config pfuze_regmap_config = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = PFUZE_NUMREGS,
> > + .cache_type = REGCACHE_RBTREE,
> > +};
> > +
> > +static int pfuze100_regulator_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id)
> > +{
> > + struct pfuze_chip *pfuze_chip;
> > + struct pfuze_regulator_platform_data *pdata =
> > + dev_get_platdata(&client->dev);
> > + struct regulator_config config = { };
> > + int i, ret;
> > +
> > + pfuze_chip = devm_kzalloc(&client->dev, sizeof(*pfuze_chip),
> > + GFP_KERNEL);
> > + if (!pfuze_chip)
> > + return -ENOMEM;
> > +
> > + dev_set_drvdata(&client->dev, pfuze_chip);
> > +
> > + memcpy(pfuze_chip->regulator_descs, pfuze100_regulators,
> > + sizeof(pfuze_chip->regulator_descs));
> > +
> > + pfuze_chip->dev = &client->dev;
> > +
> > + pfuze_chip->regmap = devm_regmap_init_i2c(client, &pfuze_regmap_config);
> > + if (IS_ERR(pfuze_chip->regmap)) {
> > + ret = PTR_ERR(pfuze_chip->regmap);
> > + dev_err(&client->dev,
> > + "regmap allocation failed with err %d\n", ret);
> > + return ret;
> > + }
> > +
> > + ret = pfuze_identify(pfuze_chip);
> > + if (ret) {
> > + dev_err(&client->dev, "unrecognized pfuze chip ID!\n");
> > + return ret;
> > + }
> > +
> > + ret = pfuze_parse_regulators_dt(pfuze_chip);
> > + if (ret)
> > + return ret;
> > +
> > + for (i = 0; i < PFUZE100_MAX_REGULATOR; i++) {
> > + struct regulator_init_data *init_data;
> > + int val;
> > +
> > + if (pdata)
> > + init_data = pdata->init_data[i];
> > + else
> > + init_data = match_init_data(i);
> > +
> > + /* SW2~SW4 high bit check and modify the voltage value table */
> > + if (i > PFUZE100_SW1C && i < PFUZE100_SWBST) {
> > + regmap_read(pfuze_chip->regmap, PFUZE100_SW2VOL +
> > + (i - PFUZE100_SW2) * 7, &val);
> > + if (val & 0x40) {
> > + pfuze_chip->regulator_descs[i].desc.min_uV
> > + = 800000;
> > + pfuze_chip->regulator_descs[i].desc.uV_step
> > + = 50000;
> > + }
> > + }
> > +
> > + config.dev = &client->dev;
> > + config.init_data = init_data;
> > + config.driver_data = pfuze_chip;
> > + config.of_node = match_of_node(i);
> > +
> > + pfuze_chip->regulators[i] = regulator_register(&pfuze_chip
> > + ->regulator_descs[i].desc, &config);
> > + if (IS_ERR(pfuze_chip->regulators[i])) {
> > + dev_err(&client->dev, "register regulator%s failed\n",
> > + pfuze100_regulators[i].desc.name);
> > + ret = PTR_ERR(pfuze_chip->regulators[i]);
> > + while (--i >= 0)
> > + regulator_unregister(pfuze_chip->regulators[i]);
> > + return ret;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int pfuze100_regulator_remove(struct i2c_client *client)
> > +{
> > + int i;
> > + struct pfuze_chip *pfuze_chip = dev_get_drvdata(&client->dev);
> > +
> > + for (i = 0; i < PFUZE100_MAX_REGULATOR; i++)
> > + regulator_unregister(pfuze_chip->regulators[i]);
> > +
> > + devm_kfree(&client->dev, pfuze_chip);
>
> This is not needed.
>
> Shawn
>
> > +
> > + return 0;
> > +}
> > +
> > +static struct i2c_driver pfuze_driver = {
> > + .id_table = pfuze_device_id,
> > + .driver = {
> > + .name = "pfuze100-regulator",
> > + .owner = THIS_MODULE,
> > + .of_match_table = pfuze_dt_ids,
> > + },
> > + .probe = pfuze100_regulator_probe,
> > + .remove = pfuze100_regulator_remove,
> > +};
> > +module_i2c_driver(pfuze_driver);
> > +
> > +MODULE_AUTHOR("Robin Gong <b38343@freescale.com>");
> > +MODULE_DESCRIPTION("Regulator Driver for Freescale PFUZE100 PMIC");
> > +MODULE_ALIAS("pfuze100-regulator");
> > diff --git a/include/linux/regulator/pfuze100.h b/include/linux/regulator/pfuze100.h
> > new file mode 100644
> > index 0000000..65d550b
> > --- /dev/null
> > +++ b/include/linux/regulator/pfuze100.h
> > @@ -0,0 +1,44 @@
> > +/*
> > + * Copyright (C) 2011-2013 Freescale Semiconductor, Inc. All Rights Reserved.
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * You should have received a copy of the GNU General Public License along
> > + * with this program; if not, write to the Free Software Foundation, Inc.,
> > + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
> > + */
> > +#ifndef __LINUX_REG_PFUZE100_H
> > +#define __LINUX_REG_PFUZE100_H
> > +
> > +#define PFUZE100_SW1AB 0
> > +#define PFUZE100_SW1C 1
> > +#define PFUZE100_SW2 2
> > +#define PFUZE100_SW3A 3
> > +#define PFUZE100_SW3B 4
> > +#define PFUZE100_SW4 5
> > +#define PFUZE100_SWBST 6
> > +#define PFUZE100_VSNVS 7
> > +#define PFUZE100_VREFDDR 8
> > +#define PFUZE100_VGEN1 9
> > +#define PFUZE100_VGEN2 10
> > +#define PFUZE100_VGEN3 11
> > +#define PFUZE100_VGEN4 12
> > +#define PFUZE100_VGEN5 13
> > +#define PFUZE100_VGEN6 14
> > +#define PFUZE100_MAX_REGULATOR 15
> > +
> > +struct regulator_init_data;
> > +
> > +struct pfuze_regulator_platform_data {
> > + struct regulator_init_data *init_data[PFUZE100_MAX_REGULATOR];
> > +};
> > +
> > +#endif /* __LINUX_REG_PFUZE100_H */
> > --
> > 1.7.5.4
> >
> >