Re: bq24190: What's the correct API to turn boost mode (OTG) on for the battery charger ?

["Mark A. Greer" <mgreer@animalcreek.com>]

[Removing Anton from CC]

On Wed, May 21, 2014 at 11:25:43AM -0700, Mark A. Greer wrote:
> On Fri, May 16, 2014 at 12:35:34AM +0200, Laurent Pinchart wrote:
> > Hi Mark,
> > 
> > Thank you for the quick reply.
> 
> Hi Laurent.  Sorry for the delay.
> 
> > On Thursday 15 May 2014 15:08:44 Mark A. Greer wrote:
> > > On Thu, May 15, 2014 at 10:29:26PM +0200, Laurent Pinchart wrote:
> > > > Hello,
> > > 
> > > [Adding Anton Vorontsov to CC list.]
> > > 
> > > Hi Laurent.
> > > 
> > > > I'm trying to enable battery charging on an OMAP4 board based on a twl6030
> > > > PMIC with external bq24190 battery charger and bq27510 fuel gauge.
> > > > 
> > > > The system has an OTG USB port that can be used to charge the battery, and
> > > > that can also be used in host mode. In that case the bq24190 needs to be
> > > > switched to boost mode to provide the +5V power supply from the battery.
> > > > 
> > > > The bq24190 has a charge configuration register field that supports charge
> > > > disabled, charge enabled and OTG (boost mode). The field is set by the
> > > > bq24190 driver in response to setting the charge type :
> > > > POWER_SUPPLY_CHARGE_TYPE_NONE will disable charing, and
> > > > POWER_SUPPLY_CHARGE_TYPE_TRICKLE and
> > > > POWER_SUPPLY_CHARGE_TYPE_FAST will enable it. However, OTG boost mode is
> > > > not supported.
> > > > 
> > > > 
> > > > The driver exposes most register fields as sysfs attributes (which doesn't
> > > > sound very safe to me, but that's another story). I can thus enable OTG
> > > > boost mode directly from userspace through the driver-specific API, but
> > > > that just bypasses the power supply API. I'm thus not very fond of that
> > > > solution.
> > >
> > > No, its not a good solution.  As indicated in the commit log, the sysfs
> > > entries are there because there are just so many fields that don't map
> > > well to the existing interface.
> > > 
> > > Maybe we should add support for a DT entry to enable exporting those
> > > fields(disabled by default)?
> > > 
> > > > Possibly due to my really basic (not to say nonexistent) knowledge of the
> > > > power supply subsystem I haven't found an API to expose this feature. I
> > > > was wondering if someone had given a though regarding how to implement
> > > > this properly.
> > > 
> > > What if we just added something like POWER_SUPPLY_CHARGE_TYPE_BOOST?
> > 
> > That was actually my first thought, and I assumed it would be rejected as 
> > boost mode is not a charge type but a discharge type :-)
> 
> Er, right.  :(
> 
> > This being said, I 
> > don't have enough experience with battery chargers to decide whether this is a 
> > good solution. If you believe it is, I'll trust you on that.
> 
> No, you're right, that isn't a good solution.
> 
> I don't see a really good fit anywhere.  The easiest thing may be to add
> a new POWER_SUPPLY_PROP_xxx power_supply_property member which can be set
> to flip it into boost mode but I'm not sure if that's really the right
> thing to do.
> 
> I hope Anton will comment on this.

After looking at MAINTAINERS and its git log, it looks like Dmitry has
taken over.

Dmitry, do you have anything insight?

Mark
--