[PATCH v2 0/7] arm: dts: oma3-gta04: Various updates

[PATCH v2 0/7] arm: dts: oma3-gta04: Various updates

[Marek Belisko]

Following patchset add various improvements to gta04 devicetree.

Changes from v1:
- added description to all patches

Marek Belisko (7):
  arm: dts: omap3-gta04: Add nand support
  arm: dts: omap3-gta04: Fix magnetometer model
  arm: dts: omap3-gta04: Add wifi reset node
  arm: dts: omap3-gta04: Move spi gpio pins to pmx_core2
  arm: dts: omap3-gta04: Add USB host support
  arm: dts: omap3-gta04: Add display alias
  arm: dts: omap3-gta04: Add twl4030 regulators parameters

 arch/arm/boot/dts/omap3-gta04.dts | 150 ++++++++++++++++++++++++++++++++++++--
 1 file changed, 145 insertions(+), 5 deletions(-)

-- 
1.9.1

[PATCH v2 1/7] arm: dts: omap3-gta04: Add nand support

[Marek Belisko]

Add the needed sections to enable nand support on
gta04 board.

Add nand partitions information.

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dts | 54 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index 021311f..7d7ddd7 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -309,3 +309,57 @@
 		};
 	};
 };
+
+&gpmc {
+	ranges = <0 0 0x30000000 0x04>; /* CS0: NAND */
+
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		nand-bus-width = <16>;
+		ti,nand-ecc-opt = "bch8";
+
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		gpmc,device-width = <2>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		x-loader@0 {
+			label = "X-Loader";
+			reg = <0 0x80000>;
+		};
+
+		bootloaders@80000 {
+			label = "U-Boot";
+			reg = <0x80000 0x1e0000>;
+		};
+
+		bootloaders_env@260000 {
+			label = "U-Boot Env";
+			reg = <0x260000 0x20000>;
+		};
+
+		kernel@280000 {
+			label = "Kernel";
+			reg = <0x280000 0x400000>;
+		};
+
+		filesystem@680000 {
+			label = "File System";
+			reg = <0x680000 0xf980000>;
+		};
+	};
+};
-- 
1.9.1

[PATCH v2 2/7] arm: dts: omap3-gta04: Fix magnetometer model

[Marek Belisko]

gta04 is using hmc5843l not hmc5843 so fix wrong compatible
entry.

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index 7d7ddd7..6d1a8d8 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -220,7 +220,7 @@
 
 	/* compass aka magnetometer */
 	hmc5843@1e {
-		compatible = "honeywell,hmc5843";
+		compatible = "honeywell,hmc5843l";
 		reg = <0x1e>;
 	};
 
-- 
1.9.1

Re: [PATCH v2 2/7] arm: dts: omap3-gta04: Fix magnetometer model

[Peter Meerwald]

> gta04 is using hmc5843l not hmc5843 so fix wrong compatible
> entry.

I guess you mean hmc5883l
 
> Signed-off-by: Marek Belisko <marek@goldelico.com>
> ---
>  arch/arm/boot/dts/omap3-gta04.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
> index 7d7ddd7..6d1a8d8 100644
> --- a/arch/arm/boot/dts/omap3-gta04.dts
> +++ b/arch/arm/boot/dts/omap3-gta04.dts
> @@ -220,7 +220,7 @@
>  
>  	/* compass aka magnetometer */
>  	hmc5843@1e {
> -		compatible = "honeywell,hmc5843";
> +		compatible = "honeywell,hmc5843l";
>  		reg = <0x1e>;
>  	};
>  
> 

-- 

Peter Meerwald
+43-664-2444418 (mobile)

Re: [PATCH v2 2/7] arm: dts: omap3-gta04: Fix magnetometer model

[Belisko Marek]

On Tue, Jul 22, 2014 at 9:46 PM, Peter Meerwald <pmeerw@pmeerw.net> wrote:
>
>> gta04 is using hmc5843l not hmc5843 so fix wrong compatible
>> entry.
>
> I guess you mean hmc5883l
Ah right. Thanks. I'll post update version.
>
>> Signed-off-by: Marek Belisko <marek@goldelico.com>
>> ---
>>  arch/arm/boot/dts/omap3-gta04.dts | 2 +-
>>  1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
>> index 7d7ddd7..6d1a8d8 100644
>> --- a/arch/arm/boot/dts/omap3-gta04.dts
>> +++ b/arch/arm/boot/dts/omap3-gta04.dts
>> @@ -220,7 +220,7 @@
>>
>>       /* compass aka magnetometer */
>>       hmc5843@1e {
>> -             compatible = "honeywell,hmc5843";
>> +             compatible = "honeywell,hmc5843l";
>>               reg = <0x1e>;
>>       };
>>
>>
>
> --
>
> Peter Meerwald
> +43-664-2444418 (mobile)

BR,

marek

-- 
as simple and primitive as possible
-------------------------------------------------
Marek Belisko - OPEN-NANDRA
Freelance Developer

Ruska Nova Ves 219 | Presov, 08005 Slovak Republic
Tel: +421 915 052 184
skype: marekwhite
twitter: #opennandra
web: http://open-nandra.com

[PATCH v2 2/7] arm: dts: omap3-gta04: Fix magnetometer model

[Marek Belisko]

gta04 is using hmc5883l not hmc5843 so fix wrong compatible
entry.

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index 7d7ddd7..4067495 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -220,7 +220,7 @@
 
 	/* compass aka magnetometer */
 	hmc5843@1e {
-		compatible = "honeywell,hmc5843";
+		compatible = "honeywell,hmc5883l";
 		reg = <0x1e>;
 	};
 
-- 
1.9.1

[PATCH v2 3/7] arm: dts: omap3-gta04: Add wifi reset node

[Marek Belisko]

Define gpio node in tca6507 which will be used as
wifi reset pin.

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dts | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index 6d1a8d8..5b08d93 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -196,6 +196,9 @@
 		#size-cells = <0>;
 		reg = <0x45>;
 
+		gpio-controller;
+		#gpio-cells = <2>;
+
 		gta04_led0: red_aux@0 {
 			label = "gta04:red:aux";
 			reg = <0x0>;
@@ -216,6 +219,11 @@
 			label = "gta04:green:power";
 			reg = <0x4>;
 		};
+
+		wifi_reset: wifi_reset@6 {
+			reg = <0x6>;
+			compatible = "gpio";
+		};
 	};
 
 	/* compass aka magnetometer */
-- 
1.9.1

[PATCH v2 4/7] arm: dts: omap3-gta04: Move spi gpio pins to pmx_core2

[Marek Belisko]

Because of commit: 3d495383648a7cda3ea51a1e2fa5d288581479aa
spi_gpio_pins node isn't valid anymore. Move to pmx_core2 node.

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dts | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index 5b08d93..4ca1277 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -141,12 +141,15 @@
                        0x0da (PIN_OUTPUT | MUX_MODE0)   /* dss_data23.dss_data23 */
                >;
        };
+};
 
+&omap3_pmx_core2 {
 	spi_gpio_pins: spi_gpio_pinmux {
-		pinctrl-single,pins = <0x5a8 (PIN_OUTPUT | MUX_MODE4) /* clk */
-			0x5b6 (PIN_OUTPUT | MUX_MODE4) /* cs */
-			0x5b8 (PIN_OUTPUT | MUX_MODE4) /* tx */
-			0x5b4 (PIN_INPUT | MUX_MODE4) /* rx */
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE4) /* clk */
+			OMAP3630_CORE2_IOPAD(0x25e6, PIN_OUTPUT | MUX_MODE4) /* cs */
+			OMAP3630_CORE2_IOPAD(0x25e8, PIN_OUTPUT | MUX_MODE4) /* tx */
+			OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT | MUX_MODE4) /* rx */
 		>;
 	};
 };
-- 
1.9.1

[PATCH v2 5/7] arm: dts: omap3-gta04: Add USB host support

[Marek Belisko]

Define USB Host port mode and the PHY device.

Also provide pin multiplexer information for USB host
pins.

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dts | 45 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 45 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index 4ca1277..370c08b 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -74,9 +74,30 @@
 			};
 		};
 	};
+
+	hsusb2_phy: hsusb2_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	};
 };
 
 &omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusb2_pins
+	>;
+
+	hsusb2_pins: pinmux_hsusb2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
+			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
+			OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
+			OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
+			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
+			OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
+		>;
+	};
+
 	uart1_pins: pinmux_uart1_pins {
 		pinctrl-single,pins = <
 			0x152 (PIN_INPUT | MUX_MODE0)		/* uart1_rx.uart1_rx */
@@ -144,6 +165,22 @@
 };
 
 &omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusb2_2_pins
+	>;
+
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
+			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
+			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
+		>;
+	};
+
 	spi_gpio_pins: spi_gpio_pinmux {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE4) /* clk */
@@ -259,6 +296,14 @@
 	power = <50>;
 };
 
+&usbhshost {
+	port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <0 &hsusb2_phy>;
+};
+
 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
-- 
1.9.1

[PATCH v2 6/7] arm: dts: omap3-gta04: Add display alias

[Marek Belisko]

Define alias for lcd display present on gta04 board.

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index 370c08b..05fd4d2 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -26,6 +26,10 @@
 		reg = <0x80000000 0x20000000>; /* 512 MB */
 	};
 
+	aliases {
+		display0 = &lcd;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 
-- 
1.9.1

[PATCH v2 7/7] arm: dts: omap3-gta04: Add twl4030 regulators parameters

[Marek Belisko]

Define voltages and properties for various twl4030
regulators used on gta04 board.

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dts | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index 05fd4d2..e39ede2 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -346,11 +346,37 @@
 	bb_uamp = <150>;
 };
 
+/* spare */
+&vaux1 {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <3000000>;
+};
+
+/* sensors */
+&vaux2 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-always-on;
+};
+
+/* camera */
+&vaux3 {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+};
+
+/* WLAN/BT */
 &vaux4 {
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <3150000>;
 };
 
+/* GPS LNA */
+&vsim {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <3150000>;
+};
+
 /* Needed to power the DPI pins */
 &vpll2 {
 	regulator-always-on;
-- 
1.9.1

Re: [PATCH v2 0/7] arm: dts: oma3-gta04: Various updates

[Tony Lindgren]

* Marek Belisko <marek@goldelico.com> [140722 12:32]:
> Following patchset add various improvements to gta04 devicetree.
> 
> Changes from v1:
> - added description to all patches
> 
> Marek Belisko (7):
>   arm: dts: omap3-gta04: Add nand support
>   arm: dts: omap3-gta04: Fix magnetometer model
>   arm: dts: omap3-gta04: Add wifi reset node
>   arm: dts: omap3-gta04: Move spi gpio pins to pmx_core2
>   arm: dts: omap3-gta04: Add USB host support
>   arm: dts: omap3-gta04: Add display alias
>   arm: dts: omap3-gta04: Add twl4030 regulators parameters
> 
>  arch/arm/boot/dts/omap3-gta04.dts | 150 ++++++++++++++++++++++++++++++++++++--
>  1 file changed, 145 insertions(+), 5 deletions(-)

Applying into omap-for-v3.17/dt thanks.

Tony