Nokia n900 problems in 3.18-rc1 (was Re: USB Ethernet gadget on Nokia n900)

Pavel Machek
2014-10-29T08:46:43Z

Hi!

> > > Here's a patch that should fix the issues for built-in USB
> > > gadgets.
> > >
> > > Pavel, care to see if this gets NFSroot over USB working again
> > > for you?
> >
> > It seems to have did the trick for me. (Plus I needed to add
> >
> > +CONFIG_ARM_ATAG_DTB_COMPAT=y
> > +CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
> > +# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is not set
> >
> > to be able to control the command line, that's why testing took me a
> > while.)
>
> Hmm I think I have a patch somewhere here to enable the standard
> bootz command for n900 mainline u-boot.. That way you can just do
>
> # bootz ${loadaddr} - ${fdtaddr}

Actually, I guess booting directly from ROM using 0xffff is easier for
testing for now.

Speaking of testing:

I'm not sure what is omap_l3_smx neccessary for, but it does not work.

[ 0.223297] omap_l3_smx omap_l3_smx.0: couldn't request debug irq
[ 0.223419] omap_l3_smx: probe of omap_l3_smx.0 failed with error
-22

There is some fun in pinmuxing:

[ 0.247131] irq: no irq domain found for /ocp/pinmux@48002030 !
[ 0.248291] irq: no irq domain found for /ocp/pinmux@48002030 !
...
[ 0.384826] omap_i2c 48070000.i2c: could not find pctldev for node
/ocp/pinmux@48002030/pinmux_i\
2c1_pins, deferring probe
[ 0.384918] platform 48070000.i2c: Driver omap_i2c requests probe
deferral
[ 0.385070] omap_i2c 48072000.i2c: could not find pctldev for node
/ocp/pinmux@48002030/pinmux_i\
2c2_pins, deferring probe
[ 0.385162] platform 48072000.i2c: Driver omap_i2c requests probe
deferral
[ 0.385284] omap_i2c 48060000.i2c: could not find pctldev for node
/ocp/pinmux@48002030/pinmux_i\
2c3_pins, deferring probe
[ 0.385375] platform 48060000.i2c: Driver omap_i2c requests probe
deferral

And serial has some problems:

[ 0.482208] of_get_named_gpiod_flags: can't parse 'rts-gpio'
property of node '/ocp/serial@4806c\
000[0]'
[ 0.482513] omap_uart 4806c000.serial: ttyO1 at MMIO 0x4806c000
(irq = 223, base_baud = 3000000)\
is a OMAP UART1
[ 0.484588] of_get_named_gpiod_flags: can't parse 'rts-gpio'
property of node '/ocp/serial@49020\
000[0]'
[ 0.484771] omap_uart 49020000.serial: ttyO2 at MMIO 0x49020000
(irq = 224, base_baud = 3000000)\
is a OMAP UART2

There's a lot of noise from probe defferal :-(. And it looks like mmc
properties have some problems:

[ 0.739349] of_get_named_gpiod_flags: can't parse 'wp-gpios'
property of node '/ocp/mmc@4809c000\
[0]'
[ 0.740142] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator
-517
[ 0.740386] platform 4809c000.mmc: Driver omap_hsmmc requests probe
deferral
[ 0.740661] of_get_named_gpiod_flags: can't parse 'cd-gpios'
property of node '/ocp/mmc@480b4000\
[0]'
[ 0.740692] of_get_named_gpiod_flags: can't parse 'wp-gpios'
property of node '/ocp/mmc@480b4000\
[0]'

omapfb reports problems, but seems to work ok:

[ 0.990386] omapfb omapfb: cannot parse default modes
[ 1.004791] Console: switching to colour frame buffer device 100x30
[ 1.073150] omapfb omapfb: using display 'lcd' mode 800x480

Best regards,
Pavel
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html