[PATCH v2 0/9] wm5110 Boot Fixups

[PATCH v2 0/9] wm5110 Boot Fixups

[Charles Keepax]

Ok so I have completed the rework to the second of the two patch
chains on this and pulled them back together into one series.

Note the main difference is I have pulled a couple patches from
the second series to the start of the chain. This is because of
patch 3 which is a bug fix for 5102 I have discovered whilst
working through this better system suspend support stuff.

Changes since v1:
 - Just updated the return of wm5110_apply_sleep_patch to use the
   ternary as per Lee's preference.

Thanks,
Charles

Charles Keepax (9):
  mfd: arizona: Use devres to manage reset GPIO
  mfd: arizona: Factor out hard reset into helper functions
  mfd: wm5102: Ensure we always boot the device fully
  mfd: arizona: Factor out SYSCLK enable from wm5102 hardware patch
  mfd: wm5110: Add register patch required for low power sleep
  regulator: arizona-ldo1: Add additional supported voltage
  mfd: wm5110: Set DCVDD voltage to 1.175V before entering sleep mode
  mfd: arizona: Add better support for system suspend
  mfd: wm5110: Add delay before releasing reset line

 drivers/mfd/arizona-core.c       |  341 ++++++++++++++++++++++++++++++++------
 drivers/regulator/arizona-ldo1.c |   15 ++
 include/linux/mfd/arizona/core.h |    1 +
 3 files changed, 302 insertions(+), 55 deletions(-)

-- 
1.7.2.5

[PATCH v2 1/9] mfd: arizona: Use devres to manage reset GPIO

[Charles Keepax]

This also handily fixes a leak of the GPIO in arizona_dev_exit.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
---
 drivers/mfd/arizona-core.c |   10 ++++------
 1 files changed, 4 insertions(+), 6 deletions(-)

diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
index 6ca6dfa..be8b1a4 100644
--- a/drivers/mfd/arizona-core.c
+++ b/drivers/mfd/arizona-core.c
@@ -728,9 +728,9 @@ int arizona_dev_init(struct arizona *arizona)
 
 	if (arizona->pdata.reset) {
 		/* Start out with /RESET low to put the chip into reset */
-		ret = gpio_request_one(arizona->pdata.reset,
-				       GPIOF_DIR_OUT | GPIOF_INIT_LOW,
-				       "arizona /RESET");
+		ret = devm_gpio_request_one(arizona->dev, arizona->pdata.reset,
+					    GPIOF_DIR_OUT | GPIOF_INIT_LOW,
+					    "arizona /RESET");
 		if (ret != 0) {
 			dev_err(dev, "Failed to request /RESET: %d\n", ret);
 			goto err_dcvdd;
@@ -1054,10 +1054,8 @@ int arizona_dev_init(struct arizona *arizona)
 err_irq:
 	arizona_irq_exit(arizona);
 err_reset:
-	if (arizona->pdata.reset) {
+	if (arizona->pdata.reset)
 		gpio_set_value_cansleep(arizona->pdata.reset, 0);
-		gpio_free(arizona->pdata.reset);
-	}
 	regulator_disable(arizona->dcvdd);
 err_enable:
 	regulator_bulk_disable(arizona->num_core_supplies,
-- 
1.7.2.5

Re: [PATCH v2 1/9] mfd: arizona: Use devres to manage reset GPIO

[Lee Jones]

On Fri, 17 Apr 2015, Charles Keepax wrote:

> This also handily fixes a leak of the GPIO in arizona_dev_exit.
> 
> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
> ---
>  drivers/mfd/arizona-core.c |   10 ++++------
>  1 files changed, 4 insertions(+), 6 deletions(-)

Acked-by: Lee Jones <lee.jones@linaro.org>

> diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
> index 6ca6dfa..be8b1a4 100644
> --- a/drivers/mfd/arizona-core.c
> +++ b/drivers/mfd/arizona-core.c
> @@ -728,9 +728,9 @@ int arizona_dev_init(struct arizona *arizona)
>  
>  	if (arizona->pdata.reset) {
>  		/* Start out with /RESET low to put the chip into reset */
> -		ret = gpio_request_one(arizona->pdata.reset,
> -				       GPIOF_DIR_OUT | GPIOF_INIT_LOW,
> -				       "arizona /RESET");
> +		ret = devm_gpio_request_one(arizona->dev, arizona->pdata.reset,
> +					    GPIOF_DIR_OUT | GPIOF_INIT_LOW,
> +					    "arizona /RESET");
>  		if (ret != 0) {
>  			dev_err(dev, "Failed to request /RESET: %d\n", ret);
>  			goto err_dcvdd;
> @@ -1054,10 +1054,8 @@ int arizona_dev_init(struct arizona *arizona)
>  err_irq:
>  	arizona_irq_exit(arizona);
>  err_reset:
> -	if (arizona->pdata.reset) {
> +	if (arizona->pdata.reset)
>  		gpio_set_value_cansleep(arizona->pdata.reset, 0);
> -		gpio_free(arizona->pdata.reset);
> -	}
>  	regulator_disable(arizona->dcvdd);
>  err_enable:
>  	regulator_bulk_disable(arizona->num_core_supplies,

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH v2 2/9] mfd: arizona: Factor out hard reset into helper functions

[Charles Keepax]

This patch adds functions for enabling and disabling the physical reset
line. This will be helpful in future refactoring.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
---
 drivers/mfd/arizona-core.c |   25 +++++++++++++++++--------
 1 files changed, 17 insertions(+), 8 deletions(-)

diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
index be8b1a4..c0e8a96 100644
--- a/drivers/mfd/arizona-core.c
+++ b/drivers/mfd/arizona-core.c
@@ -250,6 +250,20 @@ static int arizona_wait_for_boot(struct arizona *arizona)
 	return ret;
 }
 
+static inline void arizona_enable_reset(struct arizona *arizona)
+{
+	if (arizona->pdata.reset)
+		gpio_set_value_cansleep(arizona->pdata.reset, 0);
+}
+
+static void arizona_disable_reset(struct arizona *arizona)
+{
+	if (arizona->pdata.reset) {
+		gpio_set_value_cansleep(arizona->pdata.reset, 1);
+		msleep(1);
+	}
+}
+
 static int arizona_apply_hardware_patch(struct arizona* arizona)
 {
 	unsigned int fll, sysclk;
@@ -751,10 +765,7 @@ int arizona_dev_init(struct arizona *arizona)
 		goto err_enable;
 	}
 
-	if (arizona->pdata.reset) {
-		gpio_set_value_cansleep(arizona->pdata.reset, 1);
-		msleep(1);
-	}
+	arizona_disable_reset(arizona);
 
 	regcache_cache_only(arizona->regmap, false);
 
@@ -1054,8 +1065,7 @@ int arizona_dev_init(struct arizona *arizona)
 err_irq:
 	arizona_irq_exit(arizona);
 err_reset:
-	if (arizona->pdata.reset)
-		gpio_set_value_cansleep(arizona->pdata.reset, 0);
+	arizona_enable_reset(arizona);
 	regulator_disable(arizona->dcvdd);
 err_enable:
 	regulator_bulk_disable(arizona->num_core_supplies,
@@ -1080,8 +1090,7 @@ int arizona_dev_exit(struct arizona *arizona)
 	arizona_free_irq(arizona, ARIZONA_IRQ_OVERCLOCKED, arizona);
 	arizona_free_irq(arizona, ARIZONA_IRQ_CLKGEN_ERR, arizona);
 	arizona_irq_exit(arizona);
-	if (arizona->pdata.reset)
-		gpio_set_value_cansleep(arizona->pdata.reset, 0);
+	arizona_enable_reset(arizona);
 
 	regulator_bulk_disable(arizona->num_core_supplies,
 			       arizona->core_supplies);
-- 
1.7.2.5

Re: [PATCH v2 2/9] mfd: arizona: Factor out hard reset into helper functions

[Lee Jones]

On Fri, 17 Apr 2015, Charles Keepax wrote:

> This patch adds functions for enabling and disabling the physical reset
> line. This will be helpful in future refactoring.
> 
> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
> ---
>  drivers/mfd/arizona-core.c |   25 +++++++++++++++++--------
>  1 files changed, 17 insertions(+), 8 deletions(-)

Acked-by: Lee Jones <lee.jones@linaro.org>

> diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
> index be8b1a4..c0e8a96 100644
> --- a/drivers/mfd/arizona-core.c
> +++ b/drivers/mfd/arizona-core.c
> @@ -250,6 +250,20 @@ static int arizona_wait_for_boot(struct arizona *arizona)
>  	return ret;
>  }
>  
> +static inline void arizona_enable_reset(struct arizona *arizona)
> +{
> +	if (arizona->pdata.reset)
> +		gpio_set_value_cansleep(arizona->pdata.reset, 0);
> +}
> +
> +static void arizona_disable_reset(struct arizona *arizona)
> +{
> +	if (arizona->pdata.reset) {
> +		gpio_set_value_cansleep(arizona->pdata.reset, 1);
> +		msleep(1);
> +	}
> +}
> +
>  static int arizona_apply_hardware_patch(struct arizona* arizona)
>  {
>  	unsigned int fll, sysclk;
> @@ -751,10 +765,7 @@ int arizona_dev_init(struct arizona *arizona)
>  		goto err_enable;
>  	}
>  
> -	if (arizona->pdata.reset) {
> -		gpio_set_value_cansleep(arizona->pdata.reset, 1);
> -		msleep(1);
> -	}
> +	arizona_disable_reset(arizona);
>  
>  	regcache_cache_only(arizona->regmap, false);
>  
> @@ -1054,8 +1065,7 @@ int arizona_dev_init(struct arizona *arizona)
>  err_irq:
>  	arizona_irq_exit(arizona);
>  err_reset:
> -	if (arizona->pdata.reset)
> -		gpio_set_value_cansleep(arizona->pdata.reset, 0);
> +	arizona_enable_reset(arizona);
>  	regulator_disable(arizona->dcvdd);
>  err_enable:
>  	regulator_bulk_disable(arizona->num_core_supplies,
> @@ -1080,8 +1090,7 @@ int arizona_dev_exit(struct arizona *arizona)
>  	arizona_free_irq(arizona, ARIZONA_IRQ_OVERCLOCKED, arizona);
>  	arizona_free_irq(arizona, ARIZONA_IRQ_CLKGEN_ERR, arizona);
>  	arizona_irq_exit(arizona);
> -	if (arizona->pdata.reset)
> -		gpio_set_value_cansleep(arizona->pdata.reset, 0);
> +	arizona_enable_reset(arizona);
>  
>  	regulator_bulk_disable(arizona->num_core_supplies,
>  			       arizona->core_supplies);

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH v2 3/9] mfd: wm5102: Ensure we always boot the device fully

[Charles Keepax]

The wm5102 uses a custom boot sequence and the standard boot sequence is
disabled. However, the standard boot sequence must be run at least once
after a cold boot (caused by either a hard reset or removal of AVDD).
Unfortunately the register WRITE_SEQUENCER_CTRL_3 is not affected by the
hardware reset. This means if the device has been previously booted but
the AVDD supply has never been removed, arizona_dev_init will reset the
chip but the boot sequence will not run, which can cause numerous
problems. The solution is to manually clear this register and then boot
the chip again, which is what this patch does.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
---
 drivers/mfd/arizona-core.c |   50 +++++++++++++++++++++++++++++++++++--------
 1 files changed, 40 insertions(+), 10 deletions(-)

diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
index c0e8a96..73418bd 100644
--- a/drivers/mfd/arizona-core.c
+++ b/drivers/mfd/arizona-core.c
@@ -344,6 +344,33 @@ err_fll:
 		return err;
 }
 
+static int wm5102_clear_write_sequencer(struct arizona *arizona)
+{
+	int ret;
+
+	ret = regmap_write(arizona->regmap, ARIZONA_WRITE_SEQUENCER_CTRL_3,
+			   0x0);
+	if (ret) {
+		dev_err(arizona->dev,
+			"Failed to clear write sequencer state: %d\n", ret);
+		return ret;
+	}
+
+	arizona_enable_reset(arizona);
+	regulator_disable(arizona->dcvdd);
+
+	msleep(20);
+
+	ret = regulator_enable(arizona->dcvdd);
+	if (ret) {
+		dev_err(arizona->dev, "Failed to re-enable DCVDD: %d\n", ret);
+		return ret;
+	}
+	arizona_disable_reset(arizona);
+
+	return 0;
+}
+
 #ifdef CONFIG_PM
 static int arizona_runtime_resume(struct device *dev)
 {
@@ -810,21 +837,24 @@ int arizona_dev_init(struct arizona *arizona)
 	case WM5102:
 		ret = regmap_read(arizona->regmap,
 				  ARIZONA_WRITE_SEQUENCER_CTRL_3, &val);
-		if (ret != 0)
+		if (ret) {
 			dev_err(dev,
 				"Failed to check write sequencer state: %d\n",
 				ret);
-		else if (val & 0x01)
-			break;
-		/* Fall through */
-	default:
-		ret = arizona_wait_for_boot(arizona);
-		if (ret != 0) {
-			dev_err(arizona->dev,
-				"Device failed initial boot: %d\n", ret);
-			goto err_reset;
+		} else if (val & 0x01) {
+			ret = wm5102_clear_write_sequencer(arizona);
+			if (ret)
+				return ret;
 		}
 		break;
+	default:
+		break;
+	}
+
+	ret = arizona_wait_for_boot(arizona);
+	if (ret) {
+		dev_err(arizona->dev, "Device failed initial boot: %d\n", ret);
+		goto err_reset;
 	}
 
 	/* Read the device ID information & do device specific stuff */
-- 
1.7.2.5

Re: [PATCH v2 3/9] mfd: wm5102: Ensure we always boot the device fully

[Lee Jones]

On Fri, 17 Apr 2015, Charles Keepax wrote:

> The wm5102 uses a custom boot sequence and the standard boot sequence is
> disabled. However, the standard boot sequence must be run at least once
> after a cold boot (caused by either a hard reset or removal of AVDD).
> Unfortunately the register WRITE_SEQUENCER_CTRL_3 is not affected by the
> hardware reset. This means if the device has been previously booted but
> the AVDD supply has never been removed, arizona_dev_init will reset the
> chip but the boot sequence will not run, which can cause numerous
> problems. The solution is to manually clear this register and then boot
> the chip again, which is what this patch does.
> 
> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
> ---
>  drivers/mfd/arizona-core.c |   50 +++++++++++++++++++++++++++++++++++--------
>  1 files changed, 40 insertions(+), 10 deletions(-)

Hacks galore!

Acked-by: Lee Jones <lee.jones@linaro.org>

> diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
> index c0e8a96..73418bd 100644
> --- a/drivers/mfd/arizona-core.c
> +++ b/drivers/mfd/arizona-core.c
> @@ -344,6 +344,33 @@ err_fll:
>  		return err;
>  }
>  
> +static int wm5102_clear_write_sequencer(struct arizona *arizona)
> +{
> +	int ret;
> +
> +	ret = regmap_write(arizona->regmap, ARIZONA_WRITE_SEQUENCER_CTRL_3,
> +			   0x0);
> +	if (ret) {
> +		dev_err(arizona->dev,
> +			"Failed to clear write sequencer state: %d\n", ret);
> +		return ret;
> +	}
> +
> +	arizona_enable_reset(arizona);
> +	regulator_disable(arizona->dcvdd);
> +
> +	msleep(20);
> +
> +	ret = regulator_enable(arizona->dcvdd);
> +	if (ret) {
> +		dev_err(arizona->dev, "Failed to re-enable DCVDD: %d\n", ret);
> +		return ret;
> +	}
> +	arizona_disable_reset(arizona);
> +
> +	return 0;
> +}
> +
>  #ifdef CONFIG_PM
>  static int arizona_runtime_resume(struct device *dev)
>  {
> @@ -810,21 +837,24 @@ int arizona_dev_init(struct arizona *arizona)
>  	case WM5102:
>  		ret = regmap_read(arizona->regmap,
>  				  ARIZONA_WRITE_SEQUENCER_CTRL_3, &val);
> -		if (ret != 0)
> +		if (ret) {
>  			dev_err(dev,
>  				"Failed to check write sequencer state: %d\n",
>  				ret);
> -		else if (val & 0x01)
> -			break;
> -		/* Fall through */
> -	default:
> -		ret = arizona_wait_for_boot(arizona);
> -		if (ret != 0) {
> -			dev_err(arizona->dev,
> -				"Device failed initial boot: %d\n", ret);
> -			goto err_reset;
> +		} else if (val & 0x01) {
> +			ret = wm5102_clear_write_sequencer(arizona);
> +			if (ret)
> +				return ret;
>  		}
>  		break;
> +	default:
> +		break;
> +	}
> +
> +	ret = arizona_wait_for_boot(arizona);
> +	if (ret) {
> +		dev_err(arizona->dev, "Device failed initial boot: %d\n", ret);
> +		goto err_reset;
>  	}
>  
>  	/* Read the device ID information & do device specific stuff */

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH v2 4/9] mfd: arizona: Factor out SYSCLK enable from wm5102 hardware patch

[Charles Keepax]

wm5102 applies a custom hardware boot sequence, for this the SYSCLK
needs to be enabled. This patch factors out the code that enables
SYSCLK for this sequence such that it can be used for other boot time
operations that require SYSCLK.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
---
 drivers/mfd/arizona-core.c |  106 +++++++++++++++++++++++++++++---------------
 1 files changed, 70 insertions(+), 36 deletions(-)

diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
index 73418bd..f1d9ef0 100644
--- a/drivers/mfd/arizona-core.c
+++ b/drivers/mfd/arizona-core.c
@@ -264,20 +264,26 @@ static void arizona_disable_reset(struct arizona *arizona)
 	}
 }
 
-static int arizona_apply_hardware_patch(struct arizona* arizona)
+struct arizona_sysclk_state {
+	unsigned int fll;
+	unsigned int sysclk;
+};
+
+static int arizona_enable_freerun_sysclk(struct arizona *arizona,
+					 struct arizona_sysclk_state *state)
 {
-	unsigned int fll, sysclk;
 	int ret, err;
 
 	/* Cache existing FLL and SYSCLK settings */
-	ret = regmap_read(arizona->regmap, ARIZONA_FLL1_CONTROL_1, &fll);
-	if (ret != 0) {
+	ret = regmap_read(arizona->regmap, ARIZONA_FLL1_CONTROL_1, &state->fll);
+	if (ret) {
 		dev_err(arizona->dev, "Failed to cache FLL settings: %d\n",
 			ret);
 		return ret;
 	}
-	ret = regmap_read(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1, &sysclk);
-	if (ret != 0) {
+	ret = regmap_read(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1,
+			  &state->sysclk);
+	if (ret) {
 		dev_err(arizona->dev, "Failed to cache SYSCLK settings: %d\n",
 			ret);
 		return ret;
@@ -286,7 +292,7 @@ static int arizona_apply_hardware_patch(struct arizona* arizona)
 	/* Start up SYSCLK using the FLL in free running mode */
 	ret = regmap_write(arizona->regmap, ARIZONA_FLL1_CONTROL_1,
 			ARIZONA_FLL1_ENA | ARIZONA_FLL1_FREERUN);
-	if (ret != 0) {
+	if (ret) {
 		dev_err(arizona->dev,
 			"Failed to start FLL in freerunning mode: %d\n",
 			ret);
@@ -295,53 +301,81 @@ static int arizona_apply_hardware_patch(struct arizona* arizona)
 	ret = arizona_poll_reg(arizona, 25, ARIZONA_INTERRUPT_RAW_STATUS_5,
 			       ARIZONA_FLL1_CLOCK_OK_STS,
 			       ARIZONA_FLL1_CLOCK_OK_STS);
-	if (ret != 0) {
+	if (ret) {
 		ret = -ETIMEDOUT;
 		goto err_fll;
 	}
 
 	ret = regmap_write(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1, 0x0144);
-	if (ret != 0) {
+	if (ret) {
 		dev_err(arizona->dev, "Failed to start SYSCLK: %d\n", ret);
 		goto err_fll;
 	}
 
+	return 0;
+
+err_fll:
+	err = regmap_write(arizona->regmap, ARIZONA_FLL1_CONTROL_1, state->fll);
+	if (err)
+		dev_err(arizona->dev,
+			"Failed to re-apply old FLL settings: %d\n", err);
+
+	return ret;
+}
+
+static int arizona_disable_freerun_sysclk(struct arizona *arizona,
+					  struct arizona_sysclk_state *state)
+{
+	int ret;
+
+	ret = regmap_write(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1,
+			   state->sysclk);
+	if (ret) {
+		dev_err(arizona->dev,
+			"Failed to re-apply old SYSCLK settings: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_write(arizona->regmap, ARIZONA_FLL1_CONTROL_1, state->fll);
+	if (ret) {
+		dev_err(arizona->dev,
+			"Failed to re-apply old FLL settings: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int wm5102_apply_hardware_patch(struct arizona *arizona)
+{
+	struct arizona_sysclk_state state;
+	int err, ret;
+
+	ret = arizona_enable_freerun_sysclk(arizona, &state);
+	if (ret)
+		return ret;
+
 	/* Start the write sequencer and wait for it to finish */
 	ret = regmap_write(arizona->regmap, ARIZONA_WRITE_SEQUENCER_CTRL_0,
 			ARIZONA_WSEQ_ENA | ARIZONA_WSEQ_START | 160);
-	if (ret != 0) {
+	if (ret) {
 		dev_err(arizona->dev, "Failed to start write sequencer: %d\n",
 			ret);
-		goto err_sysclk;
+		goto err;
 	}
+
 	ret = arizona_poll_reg(arizona, 5, ARIZONA_WRITE_SEQUENCER_CTRL_1,
 			       ARIZONA_WSEQ_BUSY, 0);
-	if (ret != 0) {
+	if (ret) {
 		regmap_write(arizona->regmap, ARIZONA_WRITE_SEQUENCER_CTRL_0,
-				ARIZONA_WSEQ_ABORT);
+			     ARIZONA_WSEQ_ABORT);
 		ret = -ETIMEDOUT;
 	}
 
-err_sysclk:
-	err = regmap_write(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1, sysclk);
-	if (err != 0) {
-		dev_err(arizona->dev,
-			"Failed to re-apply old SYSCLK settings: %d\n",
-			err);
-	}
-
-err_fll:
-	err = regmap_write(arizona->regmap, ARIZONA_FLL1_CONTROL_1, fll);
-	if (err != 0) {
-		dev_err(arizona->dev,
-			"Failed to re-apply old FLL settings: %d\n",
-			err);
-	}
+err:
+	err = arizona_disable_freerun_sysclk(arizona, &state);
 
-	if (ret != 0)
-		return ret;
-	else
-		return err;
+	return ret ?: err;
 }
 
 static int wm5102_clear_write_sequencer(struct arizona *arizona)
@@ -407,8 +441,8 @@ static int arizona_runtime_resume(struct device *dev)
 			goto err;
 		}
 
-		ret = arizona_apply_hardware_patch(arizona);
-		if (ret != 0) {
+		ret = wm5102_apply_hardware_patch(arizona);
+		if (ret) {
 			dev_err(arizona->dev,
 				"Failed to apply hardware patch: %d\n",
 				ret);
@@ -932,8 +966,8 @@ int arizona_dev_init(struct arizona *arizona)
 
 		switch (arizona->type) {
 		case WM5102:
-			ret = arizona_apply_hardware_patch(arizona);
-			if (ret != 0) {
+			ret = wm5102_apply_hardware_patch(arizona);
+			if (ret) {
 				dev_err(arizona->dev,
 					"Failed to apply hardware patch: %d\n",
 					ret);
-- 
1.7.2.5

Re: [PATCH v2 4/9] mfd: arizona: Factor out SYSCLK enable from wm5102 hardware patch

[Lee Jones]

On Fri, 17 Apr 2015, Charles Keepax wrote:

> wm5102 applies a custom hardware boot sequence, for this the SYSCLK
> needs to be enabled. This patch factors out the code that enables
> SYSCLK for this sequence such that it can be used for other boot time
> operations that require SYSCLK.
> 
> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
> ---
>  drivers/mfd/arizona-core.c |  106 +++++++++++++++++++++++++++++---------------
>  1 files changed, 70 insertions(+), 36 deletions(-)

When you resubmit, can you seperate the functional work from the
clean-ups please?  You can add my Ack for both patches.

Acked-by: Lee Jones <lee.jones@linaro.org>

> diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
> index 73418bd..f1d9ef0 100644
> --- a/drivers/mfd/arizona-core.c
> +++ b/drivers/mfd/arizona-core.c
> @@ -264,20 +264,26 @@ static void arizona_disable_reset(struct arizona *arizona)
>  	}
>  }
>  
> -static int arizona_apply_hardware_patch(struct arizona* arizona)
> +struct arizona_sysclk_state {
> +	unsigned int fll;
> +	unsigned int sysclk;
> +};
> +
> +static int arizona_enable_freerun_sysclk(struct arizona *arizona,
> +					 struct arizona_sysclk_state *state)
>  {
> -	unsigned int fll, sysclk;
>  	int ret, err;
>  
>  	/* Cache existing FLL and SYSCLK settings */
> -	ret = regmap_read(arizona->regmap, ARIZONA_FLL1_CONTROL_1, &fll);
> -	if (ret != 0) {
> +	ret = regmap_read(arizona->regmap, ARIZONA_FLL1_CONTROL_1, &state->fll);
> +	if (ret) {
>  		dev_err(arizona->dev, "Failed to cache FLL settings: %d\n",
>  			ret);
>  		return ret;
>  	}
> -	ret = regmap_read(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1, &sysclk);
> -	if (ret != 0) {
> +	ret = regmap_read(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1,
> +			  &state->sysclk);
> +	if (ret) {
>  		dev_err(arizona->dev, "Failed to cache SYSCLK settings: %d\n",
>  			ret);
>  		return ret;
> @@ -286,7 +292,7 @@ static int arizona_apply_hardware_patch(struct arizona* arizona)
>  	/* Start up SYSCLK using the FLL in free running mode */
>  	ret = regmap_write(arizona->regmap, ARIZONA_FLL1_CONTROL_1,
>  			ARIZONA_FLL1_ENA | ARIZONA_FLL1_FREERUN);
> -	if (ret != 0) {
> +	if (ret) {
>  		dev_err(arizona->dev,
>  			"Failed to start FLL in freerunning mode: %d\n",
>  			ret);
> @@ -295,53 +301,81 @@ static int arizona_apply_hardware_patch(struct arizona* arizona)
>  	ret = arizona_poll_reg(arizona, 25, ARIZONA_INTERRUPT_RAW_STATUS_5,
>  			       ARIZONA_FLL1_CLOCK_OK_STS,
>  			       ARIZONA_FLL1_CLOCK_OK_STS);
> -	if (ret != 0) {
> +	if (ret) {
>  		ret = -ETIMEDOUT;
>  		goto err_fll;
>  	}
>  
>  	ret = regmap_write(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1, 0x0144);
> -	if (ret != 0) {
> +	if (ret) {
>  		dev_err(arizona->dev, "Failed to start SYSCLK: %d\n", ret);
>  		goto err_fll;
>  	}
>  
> +	return 0;
> +
> +err_fll:
> +	err = regmap_write(arizona->regmap, ARIZONA_FLL1_CONTROL_1, state->fll);
> +	if (err)
> +		dev_err(arizona->dev,
> +			"Failed to re-apply old FLL settings: %d\n", err);
> +
> +	return ret;
> +}
> +
> +static int arizona_disable_freerun_sysclk(struct arizona *arizona,
> +					  struct arizona_sysclk_state *state)
> +{
> +	int ret;
> +
> +	ret = regmap_write(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1,
> +			   state->sysclk);
> +	if (ret) {
> +		dev_err(arizona->dev,
> +			"Failed to re-apply old SYSCLK settings: %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = regmap_write(arizona->regmap, ARIZONA_FLL1_CONTROL_1, state->fll);
> +	if (ret) {
> +		dev_err(arizona->dev,
> +			"Failed to re-apply old FLL settings: %d\n", ret);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int wm5102_apply_hardware_patch(struct arizona *arizona)
> +{
> +	struct arizona_sysclk_state state;
> +	int err, ret;
> +
> +	ret = arizona_enable_freerun_sysclk(arizona, &state);
> +	if (ret)
> +		return ret;
> +
>  	/* Start the write sequencer and wait for it to finish */
>  	ret = regmap_write(arizona->regmap, ARIZONA_WRITE_SEQUENCER_CTRL_0,
>  			ARIZONA_WSEQ_ENA | ARIZONA_WSEQ_START | 160);
> -	if (ret != 0) {
> +	if (ret) {
>  		dev_err(arizona->dev, "Failed to start write sequencer: %d\n",
>  			ret);
> -		goto err_sysclk;
> +		goto err;
>  	}
> +
>  	ret = arizona_poll_reg(arizona, 5, ARIZONA_WRITE_SEQUENCER_CTRL_1,
>  			       ARIZONA_WSEQ_BUSY, 0);
> -	if (ret != 0) {
> +	if (ret) {
>  		regmap_write(arizona->regmap, ARIZONA_WRITE_SEQUENCER_CTRL_0,
> -				ARIZONA_WSEQ_ABORT);
> +			     ARIZONA_WSEQ_ABORT);
>  		ret = -ETIMEDOUT;
>  	}
>  
> -err_sysclk:
> -	err = regmap_write(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1, sysclk);
> -	if (err != 0) {
> -		dev_err(arizona->dev,
> -			"Failed to re-apply old SYSCLK settings: %d\n",
> -			err);
> -	}
> -
> -err_fll:
> -	err = regmap_write(arizona->regmap, ARIZONA_FLL1_CONTROL_1, fll);
> -	if (err != 0) {
> -		dev_err(arizona->dev,
> -			"Failed to re-apply old FLL settings: %d\n",
> -			err);
> -	}
> +err:
> +	err = arizona_disable_freerun_sysclk(arizona, &state);
>  
> -	if (ret != 0)
> -		return ret;
> -	else
> -		return err;
> +	return ret ?: err;
>  }
>  
>  static int wm5102_clear_write_sequencer(struct arizona *arizona)
> @@ -407,8 +441,8 @@ static int arizona_runtime_resume(struct device *dev)
>  			goto err;
>  		}
>  
> -		ret = arizona_apply_hardware_patch(arizona);
> -		if (ret != 0) {
> +		ret = wm5102_apply_hardware_patch(arizona);
> +		if (ret) {
>  			dev_err(arizona->dev,
>  				"Failed to apply hardware patch: %d\n",
>  				ret);
> @@ -932,8 +966,8 @@ int arizona_dev_init(struct arizona *arizona)
>  
>  		switch (arizona->type) {
>  		case WM5102:
> -			ret = arizona_apply_hardware_patch(arizona);
> -			if (ret != 0) {
> +			ret = wm5102_apply_hardware_patch(arizona);
> +			if (ret) {
>  				dev_err(arizona->dev,
>  					"Failed to apply hardware patch: %d\n",
>  					ret);

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH v2 5/9] mfd: wm5110: Add register patch required for low power sleep

[Charles Keepax]

Some register settings must be applied before the first time low power
sleep mode is entered on the wm5110 to ensure optimium performance.
These settings require SYSCLK to be enabled whilst they are being
applied. This patch applies the settings using the recently factored out
boot time SYSCLK functionality.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
---
 drivers/mfd/arizona-core.c |   39 +++++++++++++++++++++++++++++++++++++++
 1 files changed, 39 insertions(+), 0 deletions(-)

diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
index f1d9ef0..36dbf46 100644
--- a/drivers/mfd/arizona-core.c
+++ b/drivers/mfd/arizona-core.c
@@ -378,6 +378,35 @@ err:
 	return ret ?: err;
 }
 
+/*
+ * Register patch to some of the CODECs internal write sequences
+ * to ensure a clean exit from the low power sleep state.
+ */
+static const struct reg_default wm5110_sleep_patch[] = {
+	{ 0x337A, 0xC100 },
+	{ 0x337B, 0x0041 },
+	{ 0x3300, 0xA210 },
+	{ 0x3301, 0x050C },
+};
+
+static int wm5110_apply_sleep_patch(struct arizona *arizona)
+{
+	struct arizona_sysclk_state state;
+	int err, ret;
+
+	ret = arizona_enable_freerun_sysclk(arizona, &state);
+	if (ret)
+		return ret;
+
+	ret = regmap_multi_reg_write_bypassed(arizona->regmap,
+					      wm5110_sleep_patch,
+					      ARRAY_SIZE(wm5110_sleep_patch));
+
+	err = arizona_disable_freerun_sysclk(arizona, &state);
+
+	return ret ?: err;
+}
+
 static int wm5102_clear_write_sequencer(struct arizona *arizona)
 {
 	int ret;
@@ -974,6 +1003,16 @@ int arizona_dev_init(struct arizona *arizona)
 				goto err_reset;
 			}
 			break;
+		case WM5110:
+		case WM8280:
+			ret = wm5110_apply_sleep_patch(arizona);
+			if (ret) {
+				dev_err(arizona->dev,
+					"Failed to apply sleep patch: %d\n",
+					ret);
+				goto err_reset;
+			}
+			break;
 		default:
 			break;
 		}
-- 
1.7.2.5

[PATCH v2 6/9] regulator: arizona-ldo1: Add additional supported voltage

[Charles Keepax]

This patch adds support for the 1.175V mode on the LDO1 regulator on the
wm5110. This is need as part of the low power sleep mode operation.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/arizona-ldo1.c |   15 +++++++++++++++
 1 files changed, 15 insertions(+), 0 deletions(-)

diff --git a/drivers/regulator/arizona-ldo1.c b/drivers/regulator/arizona-ldo1.c
index 8169165..c9f6302 100644
--- a/drivers/regulator/arizona-ldo1.c
+++ b/drivers/regulator/arizona-ldo1.c
@@ -178,6 +178,16 @@ static const struct regulator_init_data arizona_ldo1_default = {
 	.num_consumer_supplies = 1,
 };
 
+static const struct regulator_init_data arizona_ldo1_wm5110 = {
+	.constraints = {
+		.min_uV = 1175000,
+		.max_uV = 1200000,
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS |
+				  REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies = 1,
+};
+
 static int arizona_ldo1_of_get_pdata(struct arizona *arizona,
 				     struct regulator_config *config,
 				     const struct regulator_desc *desc)
@@ -243,6 +253,11 @@ static int arizona_ldo1_probe(struct platform_device *pdev)
 		desc = &arizona_ldo1_hc;
 		ldo1->init_data = arizona_ldo1_dvfs;
 		break;
+	case WM5110:
+	case WM8280:
+		desc = &arizona_ldo1;
+		ldo1->init_data = arizona_ldo1_wm5110;
+		break;
 	default:
 		desc = &arizona_ldo1;
 		ldo1->init_data = arizona_ldo1_default;
-- 
1.7.2.5

[PATCH v2 7/9] mfd: wm5110: Set DCVDD voltage to 1.175V before entering sleep mode

[Charles Keepax]

The low power sleep mode on wm5110 requires that the LDO1 regulator be
set to 1.175V prior to entering sleep, then returned to 1.2V after
exiting sleep mode. This patch apply these regulator settings.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
---
 drivers/mfd/arizona-core.c |   52 ++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 52 insertions(+), 0 deletions(-)

diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
index 36dbf46..1b2fec0 100644
--- a/drivers/mfd/arizona-core.c
+++ b/drivers/mfd/arizona-core.c
@@ -478,6 +478,37 @@ static int arizona_runtime_resume(struct device *dev)
 			goto err;
 		}
 		break;
+	case WM5110:
+	case WM8280:
+		ret = arizona_wait_for_boot(arizona);
+		if (ret)
+			goto err;
+
+		if (arizona->external_dcvdd) {
+			ret = regmap_update_bits(arizona->regmap,
+						 ARIZONA_ISOLATION_CONTROL,
+						 ARIZONA_ISOLATE_DCVDD1, 0);
+			if (ret) {
+				dev_err(arizona->dev,
+					"Failed to connect DCVDD: %d\n", ret);
+				goto err;
+			}
+		} else {
+			/*
+			 * As this is only called for the internal regulator
+			 * (where we know voltage ranges available) it is ok
+			 * to request an exact range.
+			 */
+			ret = regulator_set_voltage(arizona->dcvdd,
+						    1200000, 1200000);
+			if (ret < 0) {
+				dev_err(arizona->dev,
+					"Failed to set resume voltage: %d\n",
+					ret);
+				goto err;
+			}
+		}
+		break;
 	default:
 		ret = arizona_wait_for_boot(arizona);
 		if (ret != 0) {
@@ -528,6 +559,27 @@ static int arizona_runtime_suspend(struct device *dev)
 				ret);
 			return ret;
 		}
+	} else {
+		switch (arizona->type) {
+		case WM5110:
+		case WM8280:
+			/*
+			 * As this is only called for the internal regulator
+			 * (where we know voltage ranges available) it is ok
+			 * to request an exact range.
+			 */
+			ret = regulator_set_voltage(arizona->dcvdd,
+						    1175000, 1175000);
+			if (ret < 0) {
+				dev_err(arizona->dev,
+					"Failed to set suspend voltage: %d\n",
+					ret);
+				return ret;
+			}
+			break;
+		default:
+			break;
+		}
 	}
 
 	regcache_cache_only(arizona->regmap, true);
-- 
1.7.2.5

[PATCH v2 8/9] mfd: arizona: Add better support for system suspend

[Charles Keepax]

Allow the chip to completely power off if we enter runtime suspend and
there is no jack detection active. This is helpful for systems where
system suspend might remove the supplies to the CODEC, without informing
us. Note the powering off is done in runtime suspend rather than system
suspend, because we need to hold reset until the first time DCVDD is
powered anyway (which would be in runtime resume), and we might as well
save the extra power.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
---
 drivers/mfd/arizona-core.c       |   94 +++++++++++++++++++++++++++++++-------
 include/linux/mfd/arizona/core.h |    1 +
 2 files changed, 78 insertions(+), 17 deletions(-)

diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
index 1b2fec0..def3ad3 100644
--- a/drivers/mfd/arizona-core.c
+++ b/drivers/mfd/arizona-core.c
@@ -442,12 +442,33 @@ static int arizona_runtime_resume(struct device *dev)
 
 	dev_dbg(arizona->dev, "Leaving AoD mode\n");
 
+	if (arizona->has_fully_powered_off) {
+		dev_dbg(arizona->dev, "Re-enabling core supplies\n");
+
+		ret = regulator_bulk_enable(arizona->num_core_supplies,
+					    arizona->core_supplies);
+		if (ret) {
+			dev_err(dev, "Failed to enable core supplies: %d\n",
+				ret);
+			return ret;
+		}
+	}
+
 	ret = regulator_enable(arizona->dcvdd);
 	if (ret != 0) {
 		dev_err(arizona->dev, "Failed to enable DCVDD: %d\n", ret);
+		if (arizona->has_fully_powered_off)
+			regulator_bulk_disable(arizona->num_core_supplies,
+					       arizona->core_supplies);
 		return ret;
 	}
 
+	if (arizona->has_fully_powered_off) {
+		arizona_disable_reset(arizona);
+		enable_irq(arizona->irq);
+		arizona->has_fully_powered_off = false;
+	}
+
 	regcache_cache_only(arizona->regmap, false);
 
 	switch (arizona->type) {
@@ -508,6 +529,14 @@ static int arizona_runtime_resume(struct device *dev)
 				goto err;
 			}
 		}
+
+		ret = wm5110_apply_sleep_patch(arizona);
+		if (ret) {
+			dev_err(arizona->dev,
+				"Failed to re-apply sleep patch: %d\n",
+				ret);
+			goto err;
+		}
 		break;
 	default:
 		ret = arizona_wait_for_boot(arizona);
@@ -545,10 +574,17 @@ err:
 static int arizona_runtime_suspend(struct device *dev)
 {
 	struct arizona *arizona = dev_get_drvdata(dev);
+	unsigned int val;
 	int ret;
 
 	dev_dbg(arizona->dev, "Entering AoD mode\n");
 
+	ret = regmap_read(arizona->regmap, ARIZONA_JACK_DETECT_ANALOGUE, &val);
+	if (ret) {
+		dev_err(dev, "Failed to check jack det status: %d\n", ret);
+		return ret;
+	}
+
 	if (arizona->external_dcvdd) {
 		ret = regmap_update_bits(arizona->regmap,
 					 ARIZONA_ISOLATION_CONTROL,
@@ -559,33 +595,57 @@ static int arizona_runtime_suspend(struct device *dev)
 				ret);
 			return ret;
 		}
-	} else {
-		switch (arizona->type) {
-		case WM5110:
-		case WM8280:
-			/*
-			 * As this is only called for the internal regulator
-			 * (where we know voltage ranges available) it is ok
-			 * to request an exact range.
-			 */
-			ret = regulator_set_voltage(arizona->dcvdd,
-						    1175000, 1175000);
-			if (ret < 0) {
+	}
+
+	switch (arizona->type) {
+	case WM5110:
+	case WM8280:
+		if (arizona->external_dcvdd)
+			break;
+
+		/*
+		 * As this is only called for the internal regulator
+		 * (where we know voltage ranges available) it is ok
+		 * to request an exact range.
+		 */
+		ret = regulator_set_voltage(arizona->dcvdd, 1175000, 1175000);
+		if (ret < 0) {
+			dev_err(arizona->dev,
+				"Failed to set suspend voltage: %d\n", ret);
+			return ret;
+		}
+		break;
+	case WM5102:
+		if (!(val & ARIZONA_JD1_ENA))
+			ret = regmap_write(arizona->regmap,
+					   ARIZONA_WRITE_SEQUENCER_CTRL_3, 0x0);
+			if (ret) {
 				dev_err(arizona->dev,
-					"Failed to set suspend voltage: %d\n",
+					"Failed to clear write sequencer: %d\n",
 					ret);
 				return ret;
 			}
-			break;
-		default:
-			break;
-		}
+		break;
+	default:
+		break;
 	}
 
 	regcache_cache_only(arizona->regmap, true);
 	regcache_mark_dirty(arizona->regmap);
 	regulator_disable(arizona->dcvdd);
 
+	/* Allow us to completely power down if no jack detection */
+	if (!(val & ARIZONA_JD1_ENA)) {
+		dev_dbg(arizona->dev, "Fully powering off\n");
+
+		arizona->has_fully_powered_off = true;
+
+		disable_irq(arizona->irq);
+		arizona_enable_reset(arizona);
+		regulator_bulk_disable(arizona->num_core_supplies,
+				       arizona->core_supplies);
+	}
+
 	return 0;
 }
 #endif
diff --git a/include/linux/mfd/arizona/core.h b/include/linux/mfd/arizona/core.h
index f970105..7c210af 100644
--- a/include/linux/mfd/arizona/core.h
+++ b/include/linux/mfd/arizona/core.h
@@ -117,6 +117,7 @@ struct arizona {
 	int num_core_supplies;
 	struct regulator_bulk_data core_supplies[ARIZONA_MAX_CORE_SUPPLIES];
 	struct regulator *dcvdd;
+	bool has_fully_powered_off;
 
 	struct arizona_pdata pdata;
 
-- 
1.7.2.5

Re: [PATCH v2 8/9] mfd: arizona: Add better support for system suspend

[Lee Jones]

On Fri, 17 Apr 2015, Charles Keepax wrote:

> Allow the chip to completely power off if we enter runtime suspend and
> there is no jack detection active. This is helpful for systems where
> system suspend might remove the supplies to the CODEC, without informing
> us. Note the powering off is done in runtime suspend rather than system
> suspend, because we need to hold reset until the first time DCVDD is
> powered anyway (which would be in runtime resume), and we might as well
> save the extra power.
> 
> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
> ---
>  drivers/mfd/arizona-core.c       |   94 +++++++++++++++++++++++++++++++-------
>  include/linux/mfd/arizona/core.h |    1 +
>  2 files changed, 78 insertions(+), 17 deletions(-)

It's ugly, but I can't think of a better way ...

Acked-by: Lee Jones <lee.jones@linaro.org>

> diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
> index 1b2fec0..def3ad3 100644
> --- a/drivers/mfd/arizona-core.c
> +++ b/drivers/mfd/arizona-core.c
> @@ -442,12 +442,33 @@ static int arizona_runtime_resume(struct device *dev)
>  
>  	dev_dbg(arizona->dev, "Leaving AoD mode\n");
>  
> +	if (arizona->has_fully_powered_off) {
> +		dev_dbg(arizona->dev, "Re-enabling core supplies\n");
> +
> +		ret = regulator_bulk_enable(arizona->num_core_supplies,
> +					    arizona->core_supplies);
> +		if (ret) {
> +			dev_err(dev, "Failed to enable core supplies: %d\n",
> +				ret);
> +			return ret;
> +		}
> +	}
> +
>  	ret = regulator_enable(arizona->dcvdd);
>  	if (ret != 0) {
>  		dev_err(arizona->dev, "Failed to enable DCVDD: %d\n", ret);
> +		if (arizona->has_fully_powered_off)
> +			regulator_bulk_disable(arizona->num_core_supplies,
> +					       arizona->core_supplies);
>  		return ret;
>  	}
>  
> +	if (arizona->has_fully_powered_off) {
> +		arizona_disable_reset(arizona);
> +		enable_irq(arizona->irq);
> +		arizona->has_fully_powered_off = false;
> +	}
> +
>  	regcache_cache_only(arizona->regmap, false);
>  
>  	switch (arizona->type) {
> @@ -508,6 +529,14 @@ static int arizona_runtime_resume(struct device *dev)
>  				goto err;
>  			}
>  		}
> +
> +		ret = wm5110_apply_sleep_patch(arizona);
> +		if (ret) {
> +			dev_err(arizona->dev,
> +				"Failed to re-apply sleep patch: %d\n",
> +				ret);
> +			goto err;
> +		}
>  		break;
>  	default:
>  		ret = arizona_wait_for_boot(arizona);
> @@ -545,10 +574,17 @@ err:
>  static int arizona_runtime_suspend(struct device *dev)
>  {
>  	struct arizona *arizona = dev_get_drvdata(dev);
> +	unsigned int val;
>  	int ret;
>  
>  	dev_dbg(arizona->dev, "Entering AoD mode\n");
>  
> +	ret = regmap_read(arizona->regmap, ARIZONA_JACK_DETECT_ANALOGUE, &val);
> +	if (ret) {
> +		dev_err(dev, "Failed to check jack det status: %d\n", ret);
> +		return ret;
> +	}
> +
>  	if (arizona->external_dcvdd) {
>  		ret = regmap_update_bits(arizona->regmap,
>  					 ARIZONA_ISOLATION_CONTROL,
> @@ -559,33 +595,57 @@ static int arizona_runtime_suspend(struct device *dev)
>  				ret);
>  			return ret;
>  		}
> -	} else {
> -		switch (arizona->type) {
> -		case WM5110:
> -		case WM8280:
> -			/*
> -			 * As this is only called for the internal regulator
> -			 * (where we know voltage ranges available) it is ok
> -			 * to request an exact range.
> -			 */
> -			ret = regulator_set_voltage(arizona->dcvdd,
> -						    1175000, 1175000);
> -			if (ret < 0) {
> +	}
> +
> +	switch (arizona->type) {
> +	case WM5110:
> +	case WM8280:
> +		if (arizona->external_dcvdd)
> +			break;
> +
> +		/*
> +		 * As this is only called for the internal regulator
> +		 * (where we know voltage ranges available) it is ok
> +		 * to request an exact range.
> +		 */
> +		ret = regulator_set_voltage(arizona->dcvdd, 1175000, 1175000);
> +		if (ret < 0) {
> +			dev_err(arizona->dev,
> +				"Failed to set suspend voltage: %d\n", ret);
> +			return ret;
> +		}
> +		break;
> +	case WM5102:
> +		if (!(val & ARIZONA_JD1_ENA))
> +			ret = regmap_write(arizona->regmap,
> +					   ARIZONA_WRITE_SEQUENCER_CTRL_3, 0x0);
> +			if (ret) {
>  				dev_err(arizona->dev,
> -					"Failed to set suspend voltage: %d\n",
> +					"Failed to clear write sequencer: %d\n",
>  					ret);
>  				return ret;
>  			}
> -			break;
> -		default:
> -			break;
> -		}
> +		break;
> +	default:
> +		break;
>  	}
>  
>  	regcache_cache_only(arizona->regmap, true);
>  	regcache_mark_dirty(arizona->regmap);
>  	regulator_disable(arizona->dcvdd);
>  
> +	/* Allow us to completely power down if no jack detection */
> +	if (!(val & ARIZONA_JD1_ENA)) {
> +		dev_dbg(arizona->dev, "Fully powering off\n");
> +
> +		arizona->has_fully_powered_off = true;
> +
> +		disable_irq(arizona->irq);
> +		arizona_enable_reset(arizona);
> +		regulator_bulk_disable(arizona->num_core_supplies,
> +				       arizona->core_supplies);
> +	}
> +
>  	return 0;
>  }
>  #endif
> diff --git a/include/linux/mfd/arizona/core.h b/include/linux/mfd/arizona/core.h
> index f970105..7c210af 100644
> --- a/include/linux/mfd/arizona/core.h
> +++ b/include/linux/mfd/arizona/core.h
> @@ -117,6 +117,7 @@ struct arizona {
>  	int num_core_supplies;
>  	struct regulator_bulk_data core_supplies[ARIZONA_MAX_CORE_SUPPLIES];
>  	struct regulator *dcvdd;
> +	bool has_fully_powered_off;
>  
>  	struct arizona_pdata pdata;
>  

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH v2 9/9] mfd: wm5110: Add delay before releasing reset line

[Charles Keepax]

On the wm5110 it is important the reset line is held for slightly longer
to ensure the device starts up well. This patch adds a 5mS delay for
this.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
---
 drivers/mfd/arizona-core.c |    9 +++++++++
 1 files changed, 9 insertions(+), 0 deletions(-)

diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
index def3ad3..e1f0a68 100644
--- a/drivers/mfd/arizona-core.c
+++ b/drivers/mfd/arizona-core.c
@@ -259,6 +259,15 @@ static inline void arizona_enable_reset(struct arizona *arizona)
 static void arizona_disable_reset(struct arizona *arizona)
 {
 	if (arizona->pdata.reset) {
+		switch (arizona->type) {
+		case WM5110:
+		case WM8280:
+			msleep(5);
+			break;
+		default:
+			break;
+		}
+
 		gpio_set_value_cansleep(arizona->pdata.reset, 1);
 		msleep(1);
 	}
-- 
1.7.2.5

Re: [PATCH v2 9/9] mfd: wm5110: Add delay before releasing reset line

[Lee Jones]

On Fri, 17 Apr 2015, Charles Keepax wrote:

> On the wm5110 it is important the reset line is held for slightly longer
> to ensure the device starts up well. This patch adds a 5mS delay for
> this.
> 
> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
> ---
>  drivers/mfd/arizona-core.c |    9 +++++++++
>  1 files changed, 9 insertions(+), 0 deletions(-)
> 
> diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
> index def3ad3..e1f0a68 100644
> --- a/drivers/mfd/arizona-core.c
> +++ b/drivers/mfd/arizona-core.c
> @@ -259,6 +259,15 @@ static inline void arizona_enable_reset(struct arizona *arizona)
>  static void arizona_disable_reset(struct arizona *arizona)
>  {
>  	if (arizona->pdata.reset) {
> +		switch (arizona->type) {
> +		case WM5110:
> +		case WM8280:

Comment here please.

> +			msleep(5);
> +			break;
> +		default:
> +			break;
> +		}
> +
>  		gpio_set_value_cansleep(arizona->pdata.reset, 1);
>  		msleep(1);
>  	}

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog