public inbox for linux-kernel@vger.kernel.org
 help / color / mirror / Atom feed
From: Lee Jones <lee.jones@linaro.org>
To: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Cc: linux-kernel@vger.kernel.org, patches@opensource.wolfsonmicro.com
Subject: Re: [PATCH v4] mfd: arizona: Add support for WM8998 and WM1814
Date: Thu, 14 May 2015 13:41:32 +0100	[thread overview]
Message-ID: <20150514124132.GJ22418@x1> (raw)
In-Reply-To: <20150514103314.GA2832@opensource.wolfsonmicro.com>

On Thu, 14 May 2015, Richard Fitzgerald wrote:

> On Thu, May 14, 2015 at 11:08:33AM +0100, Lee Jones wrote:
> > On Thu, 14 May 2015, Richard Fitzgerald wrote:
> > 
> > > Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
> > > ---
> > 
> > This is v4, so where's the change log?
> > 
> > I looked though my own history of the patch and I see that I already
> > Acked v3, so I'm pretty unsure what's happening.
> > 
> 
> I'm unsure too. Last I have from you on the v3 of this patch is your
> question of whether it's orthogonal enough for you to just take it. You've
> acked it, but not said that you've applied it and your for-mfd-next tree
> doesn't contain it yet so I assumed that you haven't applied it yet.
> Therefore... I've done v4 which fixes the incorrect makefile conditional
> that was in the v3 patch.

Right, so unless there are major changes, the Ack should be applied to
this patch.

If there are changes, a change-log is always helpful.  Without one I
have to re-review the whole 2k lines, which for obvious reasons I'd
like to avoid.

> If you are busy applying the v3 patch and want to take that as-is I can
> do a separate bugfix patch on top of v3 to fix the makefile.

I haven't applied the patch, only Acked it.

> > >  drivers/mfd/Kconfig                   |    6 +
> > >  drivers/mfd/Makefile                  |    3 +
> > >  drivers/mfd/arizona-core.c            |  105 ++-
> > >  drivers/mfd/arizona-i2c.c             |    8 +
> > >  drivers/mfd/arizona-irq.c             |    9 +
> > >  drivers/mfd/arizona.h                 |    5 +
> > >  drivers/mfd/wm8998-tables.c           | 1592 +++++++++++++++++++++++++++++++++
> > >  include/linux/mfd/arizona/core.h      |    3 +
> > >  include/linux/mfd/arizona/pdata.h     |    2 +
> > >  include/linux/mfd/arizona/registers.h |  220 +++++
> > >  10 files changed, 1945 insertions(+), 8 deletions(-)
> > >  create mode 100644 drivers/mfd/wm8998-tables.c
> > > 
> > > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> > > index 048f5bf..d2e549b 100644
> > > --- a/drivers/mfd/Kconfig
> > > +++ b/drivers/mfd/Kconfig
> > > @@ -1359,6 +1359,12 @@ config MFD_WM8997
> > >  	help
> > >  	  Support for Wolfson Microelectronics WM8997 low power audio SoC
> > >  
> > > +config MFD_WM8998
> > > +	bool "Wolfson Microelectronics WM8998"
> > > +	depends on MFD_ARIZONA
> > > +	help
> > > +	  Support for Wolfson Microelectronics WM8998 low power audio SoC
> > > +
> > >  config MFD_WM8400
> > >  	bool "Wolfson Microelectronics WM8400"
> > >  	select MFD_CORE
> > > diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> > > index ca6d184..d244afc 100644
> > > --- a/drivers/mfd/Makefile
> > > +++ b/drivers/mfd/Makefile
> > > @@ -50,6 +50,9 @@ endif
> > >  ifneq ($(CONFIG_MFD_WM8997),n)
> > >  obj-$(CONFIG_MFD_ARIZONA)	+= wm8997-tables.o
> > >  endif
> > > +ifeq ($(CONFIG_MFD_WM8998),y)
> > > +obj-$(CONFIG_MFD_ARIZONA)	+= wm8998-tables.o
> > > +endif

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

  reply	other threads:[~2015-05-14 12:41 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-05-14  9:24 [PATCH v4] mfd: arizona: Add support for WM8998 and WM1814 Richard Fitzgerald
2015-05-14 10:08 ` Lee Jones
2015-05-14 10:33   ` Richard Fitzgerald
2015-05-14 12:41     ` Lee Jones [this message]
2015-05-14 15:34       ` Richard Fitzgerald

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20150514124132.GJ22418@x1 \
    --to=lee.jones@linaro.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=patches@opensource.wolfsonmicro.com \
    --cc=rf@opensource.wolfsonmicro.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox