[PATCH] xhci: fix warning when CONFIG_PM disabled.

[Dave Hansen <dave@sr71.net>]

[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain, Size: 4273 bytes --]


From: Dave Hansen <dave.hansen@linux.intel.com>

I have a .config with CONFIG_PM disabled.  I get the following
whenever compiling the xhci driver:

drivers/usb/host/xhci-pci.c:192:13: warning: ‘xhci_pme_quirk’ defined but not used [-Wunused-function]

Looks like we just need to move xhci_pme_quirk() to be underneath
the CONFIG_PM #ifdef.

Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Mathias Nyman <mathias.nyman@intel.com> (supporter:USB XHCI DRIVER)
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> (supporter:USB SUBSYSTEM)
Cc: linux-usb@vger.kernel.org (open list:USB XHCI DRIVER)
Cc: linux-kernel@vger.kernel.org (open list)
---

 b/drivers/usb/host/xhci-pci.c |   90 +++++++++++++++++++++---------------------
 1 file changed, 45 insertions(+), 45 deletions(-)

diff -puN drivers/usb/host/xhci-pci.c~xhci-warning drivers/usb/host/xhci-pci.c
--- a/drivers/usb/host/xhci-pci.c~xhci-warning	2015-08-31 14:16:40.553236125 -0700
+++ b/drivers/usb/host/xhci-pci.c	2015-08-31 14:17:41.140001370 -0700
@@ -180,51 +180,6 @@ static void xhci_pci_quirks(struct devic
 				"QUIRK: Resetting on resume");
 }
 
-/*
- * In some Intel xHCI controllers, in order to get D3 working,
- * through a vendor specific SSIC CONFIG register at offset 0x883c,
- * SSIC PORT need to be marked as "unused" before putting xHCI
- * into D3. After D3 exit, the SSIC port need to be marked as "used".
- * Without this change, xHCI might not enter D3 state.
- * Make sure PME works on some Intel xHCI controllers by writing 1 to clear
- * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4
- */
-static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend)
-{
-	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
-	struct pci_dev		*pdev = to_pci_dev(hcd->self.controller);
-	u32 val;
-	void __iomem *reg;
-
-	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
-		 pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) {
-
-		reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2;
-
-		/* Notify SSIC that SSIC profile programming is not done */
-		val = readl(reg) & ~PROG_DONE;
-		writel(val, reg);
-
-		/* Mark SSIC port as unused(suspend) or used(resume) */
-		val = readl(reg);
-		if (suspend)
-			val |= SSIC_PORT_UNUSED;
-		else
-			val &= ~SSIC_PORT_UNUSED;
-		writel(val, reg);
-
-		/* Notify SSIC that SSIC profile programming is done */
-		val = readl(reg) | PROG_DONE;
-		writel(val, reg);
-		readl(reg);
-	}
-
-	reg = (void __iomem *) xhci->cap_regs + 0x80a4;
-	val = readl(reg);
-	writel(val | BIT(28), reg);
-	readl(reg);
-}
-
 #ifdef CONFIG_ACPI
 static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev)
 {
@@ -345,6 +300,51 @@ static void xhci_pci_remove(struct pci_d
 }
 
 #ifdef CONFIG_PM
+/*
+ * In some Intel xHCI controllers, in order to get D3 working,
+ * through a vendor specific SSIC CONFIG register at offset 0x883c,
+ * SSIC PORT need to be marked as "unused" before putting xHCI
+ * into D3. After D3 exit, the SSIC port need to be marked as "used".
+ * Without this change, xHCI might not enter D3 state.
+ * Make sure PME works on some Intel xHCI controllers by writing 1 to clear
+ * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4
+ */
+static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend)
+{
+	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
+	struct pci_dev		*pdev = to_pci_dev(hcd->self.controller);
+	u32 val;
+	void __iomem *reg;
+
+	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+		 pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) {
+
+		reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2;
+
+		/* Notify SSIC that SSIC profile programming is not done */
+		val = readl(reg) & ~PROG_DONE;
+		writel(val, reg);
+
+		/* Mark SSIC port as unused(suspend) or used(resume) */
+		val = readl(reg);
+		if (suspend)
+			val |= SSIC_PORT_UNUSED;
+		else
+			val &= ~SSIC_PORT_UNUSED;
+		writel(val, reg);
+
+		/* Notify SSIC that SSIC profile programming is done */
+		val = readl(reg) | PROG_DONE;
+		writel(val, reg);
+		readl(reg);
+	}
+
+	reg = (void __iomem *) xhci->cap_regs + 0x80a4;
+	val = readl(reg);
+	writel(val | BIT(28), reg);
+	readl(reg);
+}
+
 static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup)
 {
 	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
_