From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1755663AbbISRaP (ORCPT ); Sat, 19 Sep 2015 13:30:15 -0400 Received: from mail.linuxfoundation.org ([140.211.169.12]:58164 "EHLO mail.linuxfoundation.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1161049AbbISRaJ (ORCPT ); Sat, 19 Sep 2015 13:30:09 -0400 From: Greg Kroah-Hartman To: linux-kernel@vger.kernel.org Cc: Greg Kroah-Hartman , stable@vger.kernel.org, Noralf Tronnes , Martin Sperl , Mark Brown Subject: [PATCH 4.1 042/102] spi: bcm2835: set up spi-mode before asserting cs-gpio Date: Sat, 19 Sep 2015 10:27:54 -0700 Message-Id: <20150919171747.369680842@linuxfoundation.org> X-Mailer: git-send-email 2.5.3 In-Reply-To: <20150919171745.474069671@linuxfoundation.org> References: <20150919171745.474069671@linuxfoundation.org> User-Agent: quilt/0.64 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-15 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org 4.1-stable review patch. If anyone has any objections, please let me know. ------------------ From: Martin Sperl commit acace73df2c1913a526c1b41e4741a4a6704c863 upstream. When using reverse polarity for clock (spi-cpol) on a device the clock line gets altered after chip-select has been asserted resulting in an additional clock beat, which confuses hardware. This did not show when using native-CS, as the same register is used to control cs as well as polarity, so the changes came into effect at the same time. Unfortunately this is not true with gpio-cs. To avoid this situation this patch moves the setup of polarity (spi-cpol and spi-cpha) outside of the chip-select into prepare_message, which is run prior to asserting chip-select. Also fixes resetting 3-wire mode after use of rx-mode, so that a 3-Wire sequence TX, RX, TX works as well (right now it runs TX, RX, RX instead) Reported-by: Noralf Tronnes Signed-off-by: Martin Sperl Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman --- drivers/spi/spi-bcm2835.c | 28 +++++++++++++++++++++++----- 1 file changed, 23 insertions(+), 5 deletions(-) --- a/drivers/spi/spi-bcm2835.c +++ b/drivers/spi/spi-bcm2835.c @@ -257,13 +257,11 @@ static int bcm2835_spi_transfer_one(stru spi_used_hz = cdiv ? (clk_hz / cdiv) : (clk_hz / 65536); bcm2835_wr(bs, BCM2835_SPI_CLK, cdiv); - /* handle all the modes */ + /* handle all the 3-wire mode */ if ((spi->mode & SPI_3WIRE) && (tfr->rx_buf)) cs |= BCM2835_SPI_CS_REN; - if (spi->mode & SPI_CPOL) - cs |= BCM2835_SPI_CS_CPOL; - if (spi->mode & SPI_CPHA) - cs |= BCM2835_SPI_CS_CPHA; + else + cs &= ~BCM2835_SPI_CS_REN; /* for gpio_cs set dummy CS so that no HW-CS get changed * we can not run this in bcm2835_spi_set_cs, as it does @@ -291,6 +289,25 @@ static int bcm2835_spi_transfer_one(stru return bcm2835_spi_transfer_one_irq(master, spi, tfr, cs); } +static int bcm2835_spi_prepare_message(struct spi_master *master, + struct spi_message *msg) +{ + struct spi_device *spi = msg->spi; + struct bcm2835_spi *bs = spi_master_get_devdata(master); + u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS); + + cs &= ~(BCM2835_SPI_CS_CPOL | BCM2835_SPI_CS_CPHA); + + if (spi->mode & SPI_CPOL) + cs |= BCM2835_SPI_CS_CPOL; + if (spi->mode & SPI_CPHA) + cs |= BCM2835_SPI_CS_CPHA; + + bcm2835_wr(bs, BCM2835_SPI_CS, cs); + + return 0; +} + static void bcm2835_spi_handle_err(struct spi_master *master, struct spi_message *msg) { @@ -429,6 +446,7 @@ static int bcm2835_spi_probe(struct plat master->set_cs = bcm2835_spi_set_cs; master->transfer_one = bcm2835_spi_transfer_one; master->handle_err = bcm2835_spi_handle_err; + master->prepare_message = bcm2835_spi_prepare_message; master->dev.of_node = pdev->dev.of_node; bs = spi_master_get_devdata(master);