[PATCH v3 1/3] ARM: dts: vf-colibri: remove regulator container node

[PATCH v3 1/3] ARM: dts: vf-colibri: remove regulator container node

[Stefan Agner]

Drop the fake simple-bus container 'regulators' and put the
regulators directly under the root node. This also makes the
artificial 'reg' properties superfluous. While at it, remove
the unnecessary regulator-always-on property and name the
regulators according to schematics.

Signed-off-by: Stefan Agner <stefan@agner.ch>
---
Changes since v2:
- remove regulator-always-on

Changes since v1:
- rename regulators according to schematics
- drop sys prefix

 arch/arm/boot/dts/vf-colibri-eval-v3.dtsi | 42 ++++++++++++-------------------
 1 file changed, 16 insertions(+), 26 deletions(-)

diff --git a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi
index b494673..291e939 100644
--- a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi
@@ -50,32 +50,22 @@
 		clock-frequency = <16000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		sys_5v0_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "5v0";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
 
-		/* USBH_PEN */
-		usbh_vbus_reg: regulator@1 {
-			compatible = "regulator-fixed";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbh1_reg>;
-			reg = <1>;
-			regulator-name = "usbh_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio2 19 GPIO_ACTIVE_LOW>;
-			vin-supply = <&sys_5v0_reg>;
-		};
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_reg>;
+		regulator-name = "VCC_USB[1-4]";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_LOW>; /* USBH_PEN resp. USBH_P_EN */
+		vin-supply = <&reg_5v0>;
 	};
 };
 
@@ -145,7 +135,7 @@
 };
 
 &usbh1 {
-	vbus-supply = <&usbh_vbus_reg>;
+	vbus-supply = <&reg_usbh_vbus>;
 };
 
 &iomuxc {
-- 
2.7.1

[PATCH v3 2/3] ARM: dts: vf-colibri: add basic supply regulators

[Stefan Agner]

Colibri modules need to be powered using the power pins 3V3 and
AVDD_AUDIO. Add fixed regulators which represent this power rails.
Potentially, those power rails could be switched on a carrier
board. A carrier board device tree could add a own regulator with
a GPIO, and reference that regulator in a vin-supply property of
those new module level system regulators.

Signed-off-by: Stefan Agner <stefan@agner.ch>
---
Changes since v2:
- remove regulator-always-on

Changes since v1:
- Add module prefix to avoid namespace issue with Carrier Board regulators
- Name the regulators according to schematics

 arch/arm/boot/dts/vf-colibri.dtsi | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/vf-colibri.dtsi
index ff6f58e..ed4cfc5 100644
--- a/arch/arm/boot/dts/vf-colibri.dtsi
+++ b/arch/arm/boot/dts/vf-colibri.dtsi
@@ -48,14 +48,30 @@
 		enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
 		status = "disabled";
 	};
+
+	reg_module_3v3: regulator-module-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "+V3.3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_module_3v3_avdd: regulator-module-3v3-avdd {
+		compatible = "regulator-fixed";
+		regulator-name = "+V3.3_AVDD_AUDIO";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
 
 &adc0 {
 	status = "okay";
+	vref-supply = <&reg_module_3v3_avdd>;
 };
 
 &adc1 {
 	status = "okay";
+	vref-supply = <&reg_module_3v3_avdd>;
 };
 
 &can0 {
@@ -96,6 +112,7 @@
 
 &fec1 {
 	phy-mode = "rmii";
+	phy-supply = <&reg_module_3v3>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec1>;
 };
-- 
2.7.1

[PATCH v3 3/3] ARM: dts: vf-colibri: add carrier boards 3.3V supply

[Stefan Agner]

Add the carrier boards 3.3V supply as fixed regulator. This allows
to specify the power supply for nodes like backlight.

Signed-off-by: Stefan Agner <stefan@agner.ch>
---
Changes since v2:
- remove regulator-always-on

 arch/arm/boot/dts/vf-colibri-eval-v3.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi
index 291e939..4d8b7f6 100644
--- a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi
@@ -50,6 +50,13 @@
 		clock-frequency = <16000000>;
 	};
 
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_5v0: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "5V";
@@ -72,6 +79,7 @@
 &bl {
 	brightness-levels = <0 4 8 16 32 64 128 255>;
 	default-brightness-level = <6>;
+	power-supply = <&reg_3v3>;
 	status  = "okay";
 };
 
@@ -122,6 +130,10 @@
 	status = "okay";
 };
 
+&reg_module_3v3 {
+	vin-supply = <&reg_3v3>;
+};
+
 &uart0 {
 	status = "okay";
 };
-- 
2.7.1

Re: [PATCH v3 1/3] ARM: dts: vf-colibri: remove regulator container node

[Shawn Guo]

On Wed, Feb 17, 2016 at 03:40:58PM -0800, Stefan Agner wrote:
> Drop the fake simple-bus container 'regulators' and put the
> regulators directly under the root node. This also makes the
> artificial 'reg' properties superfluous. While at it, remove
> the unnecessary regulator-always-on property and name the
> regulators according to schematics.
> 
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
> Changes since v2:
> - remove regulator-always-on
> 
> Changes since v1:
> - rename regulators according to schematics
> - drop sys prefix

Okay.  Replaced v1 with v3.

Shawn