Re: X86 4.8 kernel boot questions

[Fenghua Yu <fenghua.yu@intel.com>]

On Tue, Apr 04, 2017 at 10:25:46AM -0700, Tracy Smith, CEO wrote:
> Hi All,
> 
> The production board I'm using doesn't have a JTAG available,
> upgrading to 4.8 from 4.1,.and need to understand why Linux 4.8.3
> doesn't boot on a x86_64 corei7-64. Boots with no issues with 4.1.
> 
> Hangs at the last message of u-boot, the typical "Starting kernel."
> The bootcmd and arguments are  given below.
> 
> I see a fault FFS and a message indicating the image didn't load after failover.
> 
> 1) How can I verify if the kernel image was loaded?
> 
> 2) What is this FFS fault? Where do I find this.
> 
> 3) Has the bootargs or bootcmd changed between 4.1 and 4.8.3?
> 
> 4) If the boot cmd/arg has changed, what should the boot cmd/arg be
> for 4.8.3 to boot on x86_64 corei7-64?
> 
> Initial RAM disk at linear address 0x20000000, size 11638378 bytes
> 
> Kernel command line: "BOOT_IMAGE=/imgx/bzImage LABEL=BOOT
> root=/dev/ram0 imgmnt=/media/sda2 imgdir=imgx img=image.rootfs
> rootdelay=2 slub_debug=F console=ttyS1,115200  bootcount=1
> bootcount_addr=0xa4000  acpi_enforce_resources=lax pram_size=0x800000
> pram_addr=10000000 pram_loc=ddr crashkernel=128M
> memmap=0x800000$0x10000000  "EFI table at 683392c0, mmap 68339300,
> mmap size 4c0, version 1, descr. size 0x30
> 
> Starting kernel ...
> 
> Timer summary in microseconds:
> 
>        Mark    Elapsed  Stage
>           0          0  reset
>           1          1  board_init_r
>         105        104  board_init_f
>  10,180,048 10,179,943  id=64
>  10,221,985     41,937  id=65
>  10,356,645    134,660  main_loop
>  12,366,521  2,009,876  usb_start
>  18,747,284  6,380,763  start_kernel
> Accumulated time:
>             10,162,689  ahci
> 
> 
> On a 4.1.26-yocto-standard #1 SMP it boots with no issues.  Basically
> same .config used in both cases except for anything deprecated between
> 4.1 and 4.8.3.
> 
> root@:~# cat /proc/cmdline
> BOOT_IMAGE=/imgy/bzImage LABEL=BOOT root=/dev/ram0 imgmnt=/media/sda2
> imgdir=imgy img=image.rootfs rootdelay=2 slub_debug=F
> console=ttyS1,115200 fault=FFS bootcount=3 bootcount_addr=0xa4000
> acpi_enforce_resources=lax pram_size=0x800000 pram_addr=10000000
> pram_loc=ddr crashkernel=128M memmap=0x800000$0x10000000
> 
> root@CLX3001:~# cat /proc/consoles
> ttyS1                -W- (EC p a)    4:65
> netcon0              -W- (E     )

Have you tried git bisect? You may pin point a patch that causes the
issue by git bisect.

You may also send full dmesg from serial console after hang.

Add stable kernel maintainer Greg to the list.

Thanks.

-Fenghua