[PATCHv2 0/2] mfd: omap-usb-tll: Fixes for USB TLL mode

[PATCHv2 0/2] mfd: omap-usb-tll: Fixes for USB TLL mode

[Tony Lindgren]

Hi

Here's v2 of this that move the enabling of ULPIAUTOIDLE bit into a
separate patch as suggested by Roger Quadros <rogerq@ti.com>.

Both patches can wait for v4.12.

Regards,

Tony


Tony Lindgren (2):
  mfd: omap-usb-tll: Fix inverted bit use for USB TLL mode
  mfd: omap-usb-tll: Configure ULPIAUTOIDLE

 drivers/mfd/omap-usb-tll.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

-- 
2.12.2

[PATCH 1/2] mfd: omap-usb-tll: Fix inverted bit use for USB TLL mode

[Tony Lindgren]

Commit 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver")
added support for USB TLL, but uses OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
bit the wrong way. The comments in the code are correct, but the inverted
use of OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF causes the register to be
enabled instead of disabled unlike what the comments say.

Without this change the Wrigley 3G LTE modem on droid 4 EHCI bus can
be only pinged few times before it stops responding.

Fixes: 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver")
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 drivers/mfd/omap-usb-tll.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/mfd/omap-usb-tll.c b/drivers/mfd/omap-usb-tll.c
--- a/drivers/mfd/omap-usb-tll.c
+++ b/drivers/mfd/omap-usb-tll.c
@@ -377,8 +377,8 @@ int omap_tll_init(struct usbhs_omap_platform_data *pdata)
 				 * and use SDR Mode
 				 */
 				reg &= ~(OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE
-					| OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
 					| OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE);
+				reg |= OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF;
 			} else if (pdata->port_mode[i] ==
 					OMAP_EHCI_PORT_MODE_HSIC) {
 				/*
-- 
2.12.2

Re: [PATCH 1/2] mfd: omap-usb-tll: Fix inverted bit use for USB TLL mode

[Roger Quadros]

On 15/04/17 20:05, Tony Lindgren wrote:
> Commit 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver")
> added support for USB TLL, but uses OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
> bit the wrong way. The comments in the code are correct, but the inverted
> use of OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF causes the register to be
> enabled instead of disabled unlike what the comments say.
> 
> Without this change the Wrigley 3G LTE modem on droid 4 EHCI bus can
> be only pinged few times before it stops responding.
> 
> Fixes: 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver")
> Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
> Cc: Keshava Munegowda <keshava_mgowda@ti.com>
> Cc: Marcel Partap <mpartap@gmx.net>
> Cc: Michael Scott <michael.scott@linaro.org>
> Cc: Roger Quadros <rogerq@ti.com>
> Cc: Sebastian Reichel <sre@kernel.org>
> Signed-off-by: Tony Lindgren <tony@atomide.com>

Acked-by: Roger Quadros <rogerq@ti.com>

> ---
>  drivers/mfd/omap-usb-tll.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/drivers/mfd/omap-usb-tll.c b/drivers/mfd/omap-usb-tll.c
> --- a/drivers/mfd/omap-usb-tll.c
> +++ b/drivers/mfd/omap-usb-tll.c
> @@ -377,8 +377,8 @@ int omap_tll_init(struct usbhs_omap_platform_data *pdata)
>  				 * and use SDR Mode
>  				 */
>  				reg &= ~(OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE
> -					| OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
>  					| OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE);
> +				reg |= OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF;
>  			} else if (pdata->port_mode[i] ==
>  					OMAP_EHCI_PORT_MODE_HSIC) {
>  				/*
> 

cheers,
-roger

Re: [PATCH 1/2] mfd: omap-usb-tll: Fix inverted bit use for USB TLL mode

[Lee Jones]

On Sat, 15 Apr 2017, Tony Lindgren wrote:

> Commit 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver")
> added support for USB TLL, but uses OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
> bit the wrong way. The comments in the code are correct, but the inverted
> use of OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF causes the register to be
> enabled instead of disabled unlike what the comments say.
> 
> Without this change the Wrigley 3G LTE modem on droid 4 EHCI bus can
> be only pinged few times before it stops responding.
> 
> Fixes: 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver")
> Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
> Cc: Keshava Munegowda <keshava_mgowda@ti.com>
> Cc: Marcel Partap <mpartap@gmx.net>
> Cc: Michael Scott <michael.scott@linaro.org>
> Cc: Roger Quadros <rogerq@ti.com>
> Cc: Sebastian Reichel <sre@kernel.org>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
>  drivers/mfd/omap-usb-tll.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)

Applied, thanks.

> diff --git a/drivers/mfd/omap-usb-tll.c b/drivers/mfd/omap-usb-tll.c
> --- a/drivers/mfd/omap-usb-tll.c
> +++ b/drivers/mfd/omap-usb-tll.c
> @@ -377,8 +377,8 @@ int omap_tll_init(struct usbhs_omap_platform_data *pdata)
>  				 * and use SDR Mode
>  				 */
>  				reg &= ~(OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE
> -					| OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
>  					| OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE);
> +				reg |= OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF;
>  			} else if (pdata->port_mode[i] ==
>  					OMAP_EHCI_PORT_MODE_HSIC) {
>  				/*

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH 2/2] mfd: omap-usb-tll: Configure ULPIAUTOIDLE

[Tony Lindgren]

The idle mode needs to be only disabled for UTMIAUTOIDLE while
ULPIAUTOIDLE can be enabled.

This matches the TLL_CHANNEL_CONF_i register configuration for ehci-tll
in the Motorola Linux kernel tree for Wrigley 3G LTE modem on droid 4
and the modem still stays responsive.

Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 drivers/mfd/omap-usb-tll.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/mfd/omap-usb-tll.c b/drivers/mfd/omap-usb-tll.c
--- a/drivers/mfd/omap-usb-tll.c
+++ b/drivers/mfd/omap-usb-tll.c
@@ -373,12 +373,13 @@ int omap_tll_init(struct usbhs_omap_platform_data *pdata)
 			} else if (pdata->port_mode[i] ==
 					OMAP_EHCI_PORT_MODE_TLL) {
 				/*
-				 * Disable AutoIdle, BitStuffing
-				 * and use SDR Mode
+				 * Disable UTMI AutoIdle, BitStuffing
+				 * and use SDR Mode. Enable ULPI AutoIdle.
 				 */
 				reg &= ~(OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE
 					| OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE);
 				reg |= OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF;
+				reg |= OMAP_TLL_CHANNEL_CONF_ULPI_ULPIAUTOIDLE;
 			} else if (pdata->port_mode[i] ==
 					OMAP_EHCI_PORT_MODE_HSIC) {
 				/*
-- 
2.12.2

Re: [PATCH 2/2] mfd: omap-usb-tll: Configure ULPIAUTOIDLE

[Roger Quadros]

On 15/04/17 20:05, Tony Lindgren wrote:
> The idle mode needs to be only disabled for UTMIAUTOIDLE while
> ULPIAUTOIDLE can be enabled.
> 
> This matches the TLL_CHANNEL_CONF_i register configuration for ehci-tll
> in the Motorola Linux kernel tree for Wrigley 3G LTE modem on droid 4
> and the modem still stays responsive.
> 
> Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
> Cc: Keshava Munegowda <keshava_mgowda@ti.com>
> Cc: Marcel Partap <mpartap@gmx.net>
> Cc: Michael Scott <michael.scott@linaro.org>
> Cc: Roger Quadros <rogerq@ti.com>
> Cc: Sebastian Reichel <sre@kernel.org>
> Signed-off-by: Tony Lindgren <tony@atomide.com>

Acked-by: Roger Quadros <rogerq@ti.com>

> ---
>  drivers/mfd/omap-usb-tll.c | 5 +++--
>  1 file changed, 3 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/mfd/omap-usb-tll.c b/drivers/mfd/omap-usb-tll.c
> --- a/drivers/mfd/omap-usb-tll.c
> +++ b/drivers/mfd/omap-usb-tll.c
> @@ -373,12 +373,13 @@ int omap_tll_init(struct usbhs_omap_platform_data *pdata)
>  			} else if (pdata->port_mode[i] ==
>  					OMAP_EHCI_PORT_MODE_TLL) {
>  				/*
> -				 * Disable AutoIdle, BitStuffing
> -				 * and use SDR Mode
> +				 * Disable UTMI AutoIdle, BitStuffing
> +				 * and use SDR Mode. Enable ULPI AutoIdle.
>  				 */
>  				reg &= ~(OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE
>  					| OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE);
>  				reg |= OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF;
> +				reg |= OMAP_TLL_CHANNEL_CONF_ULPI_ULPIAUTOIDLE;
>  			} else if (pdata->port_mode[i] ==
>  					OMAP_EHCI_PORT_MODE_HSIC) {
>  				/*
> 

cheers,
-roger

Re: [PATCH 2/2] mfd: omap-usb-tll: Configure ULPIAUTOIDLE

[Lee Jones]

On Sat, 15 Apr 2017, Tony Lindgren wrote:

> The idle mode needs to be only disabled for UTMIAUTOIDLE while
> ULPIAUTOIDLE can be enabled.
> 
> This matches the TLL_CHANNEL_CONF_i register configuration for ehci-tll
> in the Motorola Linux kernel tree for Wrigley 3G LTE modem on droid 4
> and the modem still stays responsive.
> 
> Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
> Cc: Keshava Munegowda <keshava_mgowda@ti.com>
> Cc: Marcel Partap <mpartap@gmx.net>
> Cc: Michael Scott <michael.scott@linaro.org>
> Cc: Roger Quadros <rogerq@ti.com>
> Cc: Sebastian Reichel <sre@kernel.org>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
>  drivers/mfd/omap-usb-tll.c | 5 +++--
>  1 file changed, 3 insertions(+), 2 deletions(-)

Applied, thanks.

> diff --git a/drivers/mfd/omap-usb-tll.c b/drivers/mfd/omap-usb-tll.c
> --- a/drivers/mfd/omap-usb-tll.c
> +++ b/drivers/mfd/omap-usb-tll.c
> @@ -373,12 +373,13 @@ int omap_tll_init(struct usbhs_omap_platform_data *pdata)
>  			} else if (pdata->port_mode[i] ==
>  					OMAP_EHCI_PORT_MODE_TLL) {
>  				/*
> -				 * Disable AutoIdle, BitStuffing
> -				 * and use SDR Mode
> +				 * Disable UTMI AutoIdle, BitStuffing
> +				 * and use SDR Mode. Enable ULPI AutoIdle.
>  				 */
>  				reg &= ~(OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE
>  					| OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE);
>  				reg |= OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF;
> +				reg |= OMAP_TLL_CHANNEL_CONF_ULPI_ULPIAUTOIDLE;
>  			} else if (pdata->port_mode[i] ==
>  					OMAP_EHCI_PORT_MODE_HSIC) {
>  				/*

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCHv2 0/2] mfd: omap-usb-tll: Fixes for USB TLL mode

[Lee Jones]

On Sat, 15 Apr 2017, Tony Lindgren wrote:

> Hi
> 
> Here's v2 of this that move the enabling of ULPIAUTOIDLE bit into a
> separate patch as suggested by Roger Quadros <rogerq@ti.com>.
> 
> Both patches can wait for v4.12.
> 
> Regards,
> 
> Tony
> 
> 
> Tony Lindgren (2):
>   mfd: omap-usb-tll: Fix inverted bit use for USB TLL mode
>   mfd: omap-usb-tll: Configure ULPIAUTOIDLE
> 
>  drivers/mfd/omap-usb-tll.c | 7 ++++---
>  1 file changed, 4 insertions(+), 3 deletions(-)

FYI: I don't know where you're getting Sam's email from, but I assume
that after being MFD-free for several years now, I'm assuming he's
lost interest in the subsystem.  Might be about time to stop CC'ing
him. :)

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCHv2 0/2] mfd: omap-usb-tll: Fixes for USB TLL mode

[Tony Lindgren]

* Lee Jones <lee.jones@linaro.org> [170424 04:46]:
> FYI: I don't know where you're getting Sam's email from, but I assume
> that after being MFD-free for several years now, I'm assuming he's
> lost interest in the subsystem.  Might be about time to stop CC'ing
> him. :)

OK fine with me, I'll stop spamming him then next time.

Tony