From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1751970AbdI2DZY (ORCPT ); Thu, 28 Sep 2017 23:25:24 -0400 Received: from mirror2.csie.ntu.edu.tw ([140.112.30.76]:53628 "EHLO wens.csie.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751349AbdI2DZV (ORCPT ); Thu, 28 Sep 2017 23:25:21 -0400 From: Chen-Yu Tsai To: Lee Jones , Mark Brown , Maxime Ripard Cc: Chen-Yu Tsai , linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-sunxi@googlegroups.com, Quentin Schulz Subject: [PATCH 7/7] ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes Date: Fri, 29 Sep 2017 11:25:14 +0800 Message-Id: <20170929032514.31727-8-wens@csie.org> X-Mailer: git-send-email 2.14.2 In-Reply-To: <20170929032514.31727-1-wens@csie.org> References: <20170929032514.31727-1-wens@csie.org> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org This patch adds device nodes for all the regulators of the AXP818 PMIC. References to the 3V dummy regulator are replaced, and it is disabled. The 3.3V and 5V are also disabled. Signed-off-by: Chen-Yu Tsai --- .../boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts | 126 ++++++++++++++++++++- 1 file changed, 124 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts index 1f0d60afb25b..1c7371d6bbb2 100644 --- a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts +++ b/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts @@ -65,7 +65,7 @@ &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ bus-width = <4>; cd-inverted; @@ -75,7 +75,8 @@ &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_emmc_pins>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; cap-mmc-hw-reset; @@ -104,6 +105,8 @@ reg = <0x3a3>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + swin-supply = <®_dcdc1>; }; ac100: codec@e89 { @@ -131,6 +134,125 @@ }; }; +#include "axp81x.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18-csi2-dsi-efuse-hdmi"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vdd-drampll-vcc18-pll-adc-cpvdd-ldoin"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pl-avcc"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-sys-vdd09-usb0-hdmi"; +}; + +®_dldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-mipi-3v3"; +}; + +®_dldo4 { + /* + * The PHY requires 20ms after all voltages are applied until core + * logic is ready and 30ms after the reset pin is de-asserted. + * Set a 100ms delay to account for PMIC ramp time and board traces. + */ + regulator-enable-ramp-delay = <100000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vdd33-pd-ave-ephy"; +}; + +®_fldo1 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd12-hsic"; +}; + +®_fldo2 { + /* + * Despite the embedded CPUs core not being used in any way, + * this must remain on or the system will hang. + */ + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc-vdd1v8-io-vdd18-lvds"; +}; + +®_sw { + regulator-name = "vcc-wifi"; +}; + +®_vcc3v0 { + status = "disabled"; +}; + +®_vcc3v3 { + status = "disabled"; +}; + +®_vcc5v0 { + status = "disabled"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pb_pins>; -- 2.14.2