From: Lars Wendler <wendler.lars@web.de>
To: Thomas Gleixner <tglx@linutronix.de>
Cc: LKML <linux-kernel@vger.kernel.org>,
x86@kernel.org, Borislav Betkov <bp@alien8.de>,
Andy Lutomirski <luto@kernel.org>,
Dave Hansen <dave.hansen@linux.intel.com>,
Peter Zijlstra <peterz@infradead.org>,
Greg KH <gregkh@linuxfoundation.org>
Subject: Re: CONFIG_PAGE_TABLE_ISOLATION=y on x86_64 causes gcc to segfault when building x86_32 binaries
Date: Wed, 3 Jan 2018 14:30:36 +0100 [thread overview]
Message-ID: <20180103143036.60e592eb@abudhabi.paradoxon.rec> (raw)
In-Reply-To: <alpine.DEB.2.20.1801031259530.1957@nanos>
[-- Attachment #1: Type: text/plain, Size: 2055 bytes --]
Am Wed, 3 Jan 2018 13:05:38 +0100 (CET)
schrieb Thomas Gleixner <tglx@linutronix.de>:
> On Wed, 3 Jan 2018, Thomas Gleixner wrote:
> > On Wed, 3 Jan 2018, Lars Wendler wrote:
> > Thanks for the report.
> >
> > > I already had a conversation with Thomas Gleixner about this
> > > issue and he asked me to post it here.
> > >
> > > After upgrading my system to vanilla 4.14.11 kernel with
> > > CONFIG_PAGE_TABLE_ISOLATION=y I could no longer build any 32bit
> > > binaries because gcc (7.2.0) segfaults.
> >
> > That's a 64bit binary, right?
Yes it is.
> > > This only happens with CONFIG_PAGE_TABLE_ISOLATION=y
> > > I can get rid of this issue by setting
> > > CONFIG_PAGE_TABLE_ISOLATION=n _or_ adding pti=off to the kernel
> > > command line (the latter was suggested by Thomas).
> > >
> > > Please find attached the kernel's config together with the dmesg
> > > output of the kernel that produces segfaults and the one with
> > > pti=off. I also attached a config.log file from a build where gcc
> > > segfaulted.
> > >
> > > If you need more information, please don't hesitate to ask.
> >
> > will do.
>
> Here you go.
>
> Is this anything special you are trying to build or is a simple
>
> gcc -m32 -o hello hello.c
A simple hello world compiles as 32bit binary but running it causes a
segfault. Compiling the same hello world as 64bit does not cause any
segfaults. Switching off pti resolves the issue and I can run the 32bit
hello world.
I first found this issue while trying to emerge gdbm-1.14 as 32bit.
Running configure failed and the config.log file said that gcc produced
a segfault while compiling a test binary called "conftest" (see the
gdbm-1.14-abi_x86_32.x86_config.log attachment in my initial report).
> Also can you please try Linus v4.15-rc6 with PTI enabled so we can see
> whether that's a backport issue or a general one?
Same problem with 4.15-rc6. So I suppose that means it's a general
issue.
> Thanks,
>
> tglx
Kind regards
Lars
[-- Attachment #2: Digitale Signatur von OpenPGP --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
next prev parent reply other threads:[~2018-01-03 13:31 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20180103123723.1dd26828@abudhabi.paradoxon.rec>
2018-01-03 11:57 ` CONFIG_PAGE_TABLE_ISOLATION=y on x86_64 causes gcc to segfault when building x86_32 binaries Thomas Gleixner
2018-01-03 12:05 ` Thomas Gleixner
2018-01-03 13:30 ` Lars Wendler [this message]
2018-01-03 15:21 ` Thomas Gleixner
2018-01-03 15:42 ` Dave Hansen
2018-01-03 18:52 ` Thomas Gleixner
2018-01-03 22:12 ` Laura Abbott
2018-01-03 22:14 ` Andy Lutomirski
2018-01-03 22:22 ` Thomas Gleixner
2018-01-03 23:43 ` Andy Lutomirski
2018-01-03 22:27 ` Dave Hansen
2018-01-03 22:25 ` [tip:x86/pti] x86/pti: Switch to kernel CR3 at early in entry_SYSCALL_compat() tip-bot for Thomas Gleixner
2018-01-03 23:46 ` CONFIG_PAGE_TABLE_ISOLATION=y on x86_64 causes gcc to segfault when building x86_32 binaries Lars Wendler
2018-01-04 2:44 ` Boris Ostrovsky
2018-01-03 15:40 ` Borislav Petkov
2018-01-03 23:22 ` Lars Wendler
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180103143036.60e592eb@abudhabi.paradoxon.rec \
--to=wendler.lars@web.de \
--cc=bp@alien8.de \
--cc=dave.hansen@linux.intel.com \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=luto@kernel.org \
--cc=peterz@infradead.org \
--cc=tglx@linutronix.de \
--cc=x86@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox