[PATCH AUTOSEL 4.4 1/7] thermal: of-thermal: disable passive polling when thermal zone is disabled

[PATCH AUTOSEL 4.4 1/7] thermal: of-thermal: disable passive polling when thermal zone is disabled

[Sasha Levin]

From: Anson Huang <Anson.Huang@nxp.com>

[ Upstream commit 152395fd03d4ce1e535a75cdbf58105e50587611 ]

When thermal zone is in passive mode, disabling its mode from
sysfs is NOT taking effect at all, it is still polling the
temperature of the disabled thermal zone and handling all thermal
trips, it makes user confused. The disabling operation should
disable the thermal zone behavior completely, for both active and
passive mode, this patch clears the passive_delay when thermal
zone is disabled and restores it when it is enabled.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/thermal/of-thermal.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/thermal/of-thermal.c b/drivers/thermal/of-thermal.c
index be4eedcb839a..236c4eb5cf78 100644
--- a/drivers/thermal/of-thermal.c
+++ b/drivers/thermal/of-thermal.c
@@ -284,10 +284,13 @@ static int of_thermal_set_mode(struct thermal_zone_device *tz,
 
 	mutex_lock(&tz->lock);
 
-	if (mode == THERMAL_DEVICE_ENABLED)
+	if (mode == THERMAL_DEVICE_ENABLED) {
 		tz->polling_delay = data->polling_delay;
-	else
+		tz->passive_delay = data->passive_delay;
+	} else {
 		tz->polling_delay = 0;
+		tz->passive_delay = 0;
+	}
 
 	mutex_unlock(&tz->lock);
 
-- 
2.17.1

[PATCH AUTOSEL 4.4 2/7] net: hns: fix length and page_offset overflow when CONFIG_ARM64_64K_PAGES

[Sasha Levin]

From: Huazhong Tan <tanhuazhong@huawei.com>

[ Upstream commit 3ed614dce3ca9912d22be215ff0f11104b69fe62 ]

When enable the config item "CONFIG_ARM64_64K_PAGES", the size of PAGE_SIZE
is 65536(64K). But the  type of length and page_offset are u16, they will
overflow. So change them to u32.

Fixes: 6fe6611ff275 ("net: add Hisilicon Network Subsystem hnae framework support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/ethernet/hisilicon/hns/hnae.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/hisilicon/hns/hnae.h b/drivers/net/ethernet/hisilicon/hns/hnae.h
index cec95ac8687d..fe37fc7ec76e 100644
--- a/drivers/net/ethernet/hisilicon/hns/hnae.h
+++ b/drivers/net/ethernet/hisilicon/hns/hnae.h
@@ -171,10 +171,10 @@ struct hnae_desc_cb {
 
 	/* priv data for the desc, e.g. skb when use with ip stack*/
 	void *priv;
-	u16 page_offset;
-	u16 reuse_flag;
+	u32 page_offset;
+	u32 length;     /* length of the buffer */
 
-	u16 length;     /* length of the buffer */
+	u16 reuse_flag;
 
        /* desc type, used by the ring user to mark the type of the priv data */
 	u16 type;
-- 
2.17.1

[PATCH AUTOSEL 4.4 3/7] e1000: check on netif_running() before calling e1000_up()

[Sasha Levin]

From: Bo Chen <chenbo@pdx.edu>

[ Upstream commit cf1acec008f8d7761aa3fd7c4bca7e17b2d2512d ]

When the device is not up, the call to 'e1000_up()' from the error handling path
of 'e1000_set_ringparam()' causes a kernel oops with a null-pointer
dereference. The null-pointer dereference is triggered in function
'e1000_alloc_rx_buffers()' at line 'buffer_info = &rx_ring->buffer_info[i]'.

This bug was reported by COD, a tool for testing kernel module binaries I am
building. This bug was also detected by KFI from Dr. Kai Cong.

This patch fixes the bug by checking on 'netif_running()' before calling
'e1000_up()' in 'e1000_set_ringparam()'.

Signed-off-by: Bo Chen <chenbo@pdx.edu>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/ethernet/intel/e1000/e1000_ethtool.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
index 83e557c7f279..52129b214c09 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
@@ -665,7 +665,8 @@ static int e1000_set_ringparam(struct net_device *netdev,
 err_alloc_rx:
 	kfree(txdr);
 err_alloc_tx:
-	e1000_up(adapter);
+	if (netif_running(adapter->netdev))
+		e1000_up(adapter);
 err_setup:
 	clear_bit(__E1000_RESETTING, &adapter->flags);
 	return err;
-- 
2.17.1

[PATCH AUTOSEL 4.4 4/7] e1000: ensure to free old tx/rx rings in set_ringparam()

[Sasha Levin]

From: Bo Chen <chenbo@pdx.edu>

[ Upstream commit ee400a3f1bfe7004a3e14b81c38ccc5583c26295 ]

In 'e1000_set_ringparam()', the tx_ring and rx_ring are updated with new value
and the old tx/rx rings are freed only when the device is up. There are resource
leaks on old tx/rx rings when the device is not up. This bug is reported by COD,
a tool for testing kernel module binaries I am building.

This patch fixes the bug by always calling 'kfree()' on old tx/rx rings in
'e1000_set_ringparam()'.

Signed-off-by: Bo Chen <chenbo@pdx.edu>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/ethernet/intel/e1000/e1000_ethtool.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
index 52129b214c09..5ae8874bbf72 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
@@ -645,14 +645,14 @@ static int e1000_set_ringparam(struct net_device *netdev,
 		adapter->tx_ring = tx_old;
 		e1000_free_all_rx_resources(adapter);
 		e1000_free_all_tx_resources(adapter);
-		kfree(tx_old);
-		kfree(rx_old);
 		adapter->rx_ring = rxdr;
 		adapter->tx_ring = txdr;
 		err = e1000_up(adapter);
 		if (err)
 			goto err_setup;
 	}
+	kfree(tx_old);
+	kfree(rx_old);
 
 	clear_bit(__E1000_RESETTING, &adapter->flags);
 	return 0;
-- 
2.17.1

[PATCH AUTOSEL 4.4 6/7] hwmon: (adt7475) Make adt7475_read_word() return errors

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit f196dec6d50abb2e65fb54a0621b2f1b4d922995 ]

The adt7475_read_word() function was meant to return negative error
codes on failure.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/hwmon/adt7475.c | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)

diff --git a/drivers/hwmon/adt7475.c b/drivers/hwmon/adt7475.c
index 3cefd1aeb24f..9c262d955331 100644
--- a/drivers/hwmon/adt7475.c
+++ b/drivers/hwmon/adt7475.c
@@ -274,14 +274,18 @@ static inline u16 volt2reg(int channel, long volt, u8 bypass_attn)
 	return clamp_val(reg, 0, 1023) & (0xff << 2);
 }
 
-static u16 adt7475_read_word(struct i2c_client *client, int reg)
+static int adt7475_read_word(struct i2c_client *client, int reg)
 {
-	u16 val;
+	int val1, val2;
 
-	val = i2c_smbus_read_byte_data(client, reg);
-	val |= (i2c_smbus_read_byte_data(client, reg + 1) << 8);
+	val1 = i2c_smbus_read_byte_data(client, reg);
+	if (val1 < 0)
+		return val1;
+	val2 = i2c_smbus_read_byte_data(client, reg + 1);
+	if (val2 < 0)
+		return val2;
 
-	return val;
+	return val1 | (val2 << 8);
 }
 
 static void adt7475_write_word(struct i2c_client *client, int reg, u16 val)
-- 
2.17.1

[PATCH AUTOSEL 4.4 5/7] hwmon: (ina2xx) fix sysfs shunt resistor read access

[Sasha Levin]

From: Lothar Felten <lothar.felten@gmail.com>

[ Upstream commit 3ad867001c91657c46dcf6656d52eb6080286fd5 ]

fix the sysfs shunt resistor read access: return the shunt resistor
value, not the calibration register contents.

update email address

Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 Documentation/hwmon/ina2xx           |  2 +-
 drivers/hwmon/ina2xx.c               | 13 +++++++++++--
 include/linux/platform_data/ina2xx.h |  2 +-
 3 files changed, 13 insertions(+), 4 deletions(-)

diff --git a/Documentation/hwmon/ina2xx b/Documentation/hwmon/ina2xx
index cfd31d94c872..f8bf14055c2f 100644
--- a/Documentation/hwmon/ina2xx
+++ b/Documentation/hwmon/ina2xx
@@ -32,7 +32,7 @@ Supported chips:
     Datasheet: Publicly available at the Texas Instruments website
                http://www.ti.com/
 
-Author: Lothar Felten <l-felten@ti.com>
+Author: Lothar Felten <lothar.felten@gmail.com>
 
 Description
 -----------
diff --git a/drivers/hwmon/ina2xx.c b/drivers/hwmon/ina2xx.c
index ac63e562071f..9ac6e1673375 100644
--- a/drivers/hwmon/ina2xx.c
+++ b/drivers/hwmon/ina2xx.c
@@ -17,7 +17,7 @@
  * Bi-directional Current/Power Monitor with I2C Interface
  * Datasheet: http://www.ti.com/product/ina230
  *
- * Copyright (C) 2012 Lothar Felten <l-felten@ti.com>
+ * Copyright (C) 2012 Lothar Felten <lothar.felten@gmail.com>
  * Thanks to Jan Volkering
  *
  * This program is free software; you can redistribute it and/or modify
@@ -328,6 +328,15 @@ static int ina2xx_set_shunt(struct ina2xx_data *data, long val)
 	return 0;
 }
 
+static ssize_t ina2xx_show_shunt(struct device *dev,
+			      struct device_attribute *da,
+			      char *buf)
+{
+	struct ina2xx_data *data = dev_get_drvdata(dev);
+
+	return snprintf(buf, PAGE_SIZE, "%li\n", data->rshunt);
+}
+
 static ssize_t ina2xx_store_shunt(struct device *dev,
 				  struct device_attribute *da,
 				  const char *buf, size_t count)
@@ -402,7 +411,7 @@ static SENSOR_DEVICE_ATTR(power1_input, S_IRUGO, ina2xx_show_value, NULL,
 
 /* shunt resistance */
 static SENSOR_DEVICE_ATTR(shunt_resistor, S_IRUGO | S_IWUSR,
-			  ina2xx_show_value, ina2xx_store_shunt,
+			  ina2xx_show_shunt, ina2xx_store_shunt,
 			  INA2XX_CALIBRATION);
 
 /* update interval (ina226 only) */
diff --git a/include/linux/platform_data/ina2xx.h b/include/linux/platform_data/ina2xx.h
index 9abc0ca7259b..9f0aa1b48c78 100644
--- a/include/linux/platform_data/ina2xx.h
+++ b/include/linux/platform_data/ina2xx.h
@@ -1,7 +1,7 @@
 /*
  * Driver for Texas Instruments INA219, INA226 power monitor chips
  *
- * Copyright (C) 2012 Lothar Felten <l-felten@ti.com>
+ * Copyright (C) 2012 Lothar Felten <lothar.felten@gmail.com>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
-- 
2.17.1

[PATCH AUTOSEL 4.4 7/7] i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBus

[Sasha Levin]

From: Mika Westerberg <mika.westerberg@linux.intel.com>

[ Upstream commit 7fd6d98b89f382d414e1db528e29a67bbd749457 ]

Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict
with PCI BAR") made it possible for AML code to access SMBus I/O ports
by installing custom SystemIO OpRegion handler and blocking i80i driver
access upon first AML read/write to this OpRegion.

However, while ThinkPad T560 does have SystemIO OpRegion declared under
the SMBus device, it does not access any of the SMBus registers:

    Device (SMBU)
    {
        ...

        OperationRegion (SMBP, PCI_Config, 0x50, 0x04)
        Field (SMBP, DWordAcc, NoLock, Preserve)
        {
            ,   5,
            TCOB,   11,
            Offset (0x04)
        }

        Name (TCBV, 0x00)
        Method (TCBS, 0, NotSerialized)
        {
            If ((TCBV == 0x00))
            {
            TCBV = (\_SB.PCI0.SMBU.TCOB << 0x05)
            }

            Return (TCBV) /* \_SB_.PCI0.SMBU.TCBV */
        }

        OperationRegion (TCBA, SystemIO, TCBS (), 0x10)
        Field (TCBA, ByteAcc, NoLock, Preserve)
        {
            Offset (0x04),
            ,   9,
            CPSC,   1
        }
    }

Problem with the current approach is that it blocks all I/O port access
and because this system has touchpad connected to the SMBus controller
after first AML access (happens during suspend/resume cycle) the
touchpad fails to work anymore.

Fix this so that we allow ACPI AML I/O port access if it does not touch
the region reserved for the SMBus.

Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737
Reported-by: Yussuf Khalil <dev@pp3345.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/i2c/busses/i2c-i801.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
index 85f39cc3e276..675d634c13d0 100644
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -1267,6 +1267,13 @@ static void i801_add_tco(struct i801_priv *priv)
 }
 
 #ifdef CONFIG_ACPI
+static bool i801_acpi_is_smbus_ioport(const struct i801_priv *priv,
+				      acpi_physical_address address)
+{
+	return address >= priv->smba &&
+	       address <= pci_resource_end(priv->pci_dev, SMBBAR);
+}
+
 static acpi_status
 i801_acpi_io_handler(u32 function, acpi_physical_address address, u32 bits,
 		     u64 *value, void *handler_context, void *region_context)
@@ -1282,7 +1289,7 @@ i801_acpi_io_handler(u32 function, acpi_physical_address address, u32 bits,
 	 */
 	mutex_lock(&priv->acpi_lock);
 
-	if (!priv->acpi_reserved) {
+	if (!priv->acpi_reserved && i801_acpi_is_smbus_ioport(priv, address)) {
 		priv->acpi_reserved = true;
 
 		dev_warn(&pdev->dev, "BIOS is accessing SMBus registers\n");
-- 
2.17.1