[PATCH v3 2/4] iio: adc: add STMPE ADC driver using IIO framework

Philippe Schenker
2018-11-23T14:24:37Z

From: Stefan Agner <stefan@agner.ch>

This adds an ADC driver for the STMPE device using the industrial
input/output interface. The driver supports raw reading of values.
The driver depends on the MFD STMPE driver. If the touchscreen
block is enabled too, only four of the 8 ADC channels are available.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
---

Changes in v3:
- Undo ADC-settings related code-deletions in stmpe-ts.c that the code is
backwards-compatible to older devicetrees.

Changes in v2:
- Code formatting
- Move code to setup ADC to MFD device, as it is used by both drivers
adc and touchscreen
- Removed unused includes
- Defined the macro STMPE_START_ONE_TEMP_CONV with other macros.
- Added new macro that defines the channel of the temperature sensor.
Took new name for STMPE_MAX_ADC->STMPE_ADC_LAST_NR and used it throughout
the code for better readability.
- Added mutex_unlock where missing.

drivers/iio/adc/Kconfig | 7 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/stmpe-adc.c | 326 +++++++++++++++++++++++++++
drivers/input/touchscreen/stmpe-ts.c | 36 +--
drivers/mfd/Kconfig | 3 +-
drivers/mfd/stmpe.c | 81 +++++++
include/linux/mfd/stmpe.h | 9 +
7 files changed, 437 insertions(+), 26 deletions(-)
create mode 100644 drivers/iio/adc/stmpe-adc.c

diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index a52fea8749a9..224f2067494d 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -734,6 +734,13 @@ config STM32_DFSDM_ADC
This driver can also be built as a module. If so, the module
will be called stm32-dfsdm-adc.

+config STMPE_ADC
+ tristate "STMicroelectronics STMPE ADC driver"
+ depends on OF && MFD_STMPE
+ help
+ Say yes here to build support for ST Microelectronics STMPE
+ built-in ADC block (stmpe811).
+
config STX104
tristate "Apex Embedded Systems STX104 driver"
depends on PC104 && X86
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index a6e6a0b659e2..cba889c30bf9 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -69,6 +69,7 @@ obj-$(CONFIG_STM32_ADC_CORE) += stm32-adc-core.o
obj-$(CONFIG_STM32_ADC) += stm32-adc.o
obj-$(CONFIG_STM32_DFSDM_CORE) += stm32-dfsdm-core.o
obj-$(CONFIG_STM32_DFSDM_ADC) += stm32-dfsdm-adc.o
+obj-$(CONFIG_STMPE_ADC) += stmpe-adc.o
obj-$(CONFIG_TI_ADC081C) += ti-adc081c.o
obj-$(CONFIG_TI_ADC0832) += ti-adc0832.o
obj-$(CONFIG_TI_ADC084S021) += ti-adc084s021.o
diff --git a/drivers/iio/adc/stmpe-adc.c b/drivers/iio/adc/stmpe-adc.c
new file mode 100644
index 000000000000..bea3f3c27bb5
--- /dev/null
+++ b/drivers/iio/adc/stmpe-adc.c
@@ -0,0 +1,326 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * STMicroelectronics STMPE811 IIO ADC Driver
+ *
+ * 4 channel, 10/12-bit ADC
+ *
+ * Copyright (C) 2013-2018 Toradex AG <stefan.agner@toradex.com>
+ */
+
+#include <linux/completion.h>
+#include <linux/err.h>
+#include <linux/iio/iio.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/stmpe.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+#define STMPE_REG_INT_STA 0x0B
+#define STMPE_REG_ADC_INT_EN 0x0E
+#define STMPE_REG_ADC_INT_STA 0x0F
+
+#define STMPE_REG_ADC_CTRL1 0x20
+#define STMPE_REG_ADC_CTRL2 0x21
+#define STMPE_REG_ADC_CAPT 0x22
+#define STMPE_REG_ADC_DATA_CH(channel) (0x30 + 2 * (channel))
+
+#define STMPE_REG_TEMP_CTRL 0x60
+#define STMPE_TEMP_CTRL_ENABLE BIT(0)
+#define STMPE_TEMP_CTRL_ACQ BIT(1)
+#define STMPE_TEMP_CTRL_THRES_EN BIT(3)
+#define STMPE_START_ONE_TEMP_CONV (STMPE_TEMP_CTRL_ENABLE | \
+ STMPE_TEMP_CTRL_ACQ | \
+ STMPE_TEMP_CTRL_THRES_EN)
+#define STMPE_REG_TEMP_DATA 0x61
+#define STMPE_REG_TEMP_TH 0x63
+#define STMPE_ADC_LAST_NR 7
+#define STMPE_TEMP_CHANNEL (STMPE_ADC_LAST_NR + 1)
+
+#define STMPE_ADC_CH(channel) ((1 << (channel)) & 0xff)
+
+#define STMPE_ADC_TIMEOUT msecs_to_jiffies(1000)
+
+struct stmpe_adc {
+ struct stmpe *stmpe;
+ struct clk *clk;
+ struct device *dev;
+
+ /* We are allocating plus one for the temperature channel */
+ struct iio_chan_spec stmpe_adc_iio_channels[STMPE_ADC_LAST_NR + 2];
+
+ struct completion completion;
+
+ u8 channel;
+ u32 value;
+};
+
+static int stmpe_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val,
+ int *val2,
+ long mask)
+{
+ struct stmpe_adc *info = iio_priv(indio_dev);
+ long ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ case IIO_CHAN_INFO_PROCESSED:
+
+ mutex_lock(&indio_dev->mlock);
+
+ info->channel = (u8)chan->channel;
+
+ switch (chan->type) {
+ case IIO_VOLTAGE:
+ if (info->channel > STMPE_ADC_LAST_NR) {
+ mutex_unlock(&indio_dev->mlock);
+ return -EINVAL;
+ }
+
+ stmpe_reg_write(info->stmpe, STMPE_REG_ADC_INT_EN,
+ STMPE_ADC_CH(info->channel));
+
+ stmpe_reg_write(info->stmpe, STMPE_REG_ADC_CAPT,
+ STMPE_ADC_CH(info->channel));
+
+ *val = info->value;
+ break;
+
+ case IIO_TEMP:
+ if (info->channel != STMPE_TEMP_CHANNEL) {
+ mutex_unlock(&indio_dev->mlock);
+ return -EINVAL;
+ }
+
+ stmpe_reg_write(info->stmpe, STMPE_REG_TEMP_CTRL,
+ STMPE_START_ONE_TEMP_CONV);
+ break;
+ default:
+ mutex_unlock(&indio_dev->mlock);
+ return -EINVAL;
+ }
+
+ ret = wait_for_completion_interruptible_timeout
+ (&info->completion, STMPE_ADC_TIMEOUT);
+
+ if (ret <= 0) {
+ mutex_unlock(&indio_dev->mlock);
+ if (ret == 0)
+ return -ETIMEDOUT;
+ else
+ return ret;
+ }
+
+ switch (chan->type) {
+ case IIO_VOLTAGE:
+ *val = info->value;
+ break;
+
+ case IIO_TEMP:
+ /*
+ * absolute temp = +V3.3 * value /7.51 [K]
+ * scale to [milli °C]
+ */
+ *val = ((449960l * info->value) / 1024l) - 273150;
+ break;
+ default:
+ break;
+ }
+
+ mutex_unlock(&indio_dev->mlock);
+ return IIO_VAL_INT;
+
+ case IIO_CHAN_INFO_SCALE:
+ *val = 3300;
+ *val2 = info->stmpe->mod_12b ? 12 : 10;
+ return IIO_VAL_FRACTIONAL_LOG2;
+
+ default:
+ break;
+ }
+
+ return -EINVAL;
+}
+
+static irqreturn_t stmpe_adc_isr(int irq, void *dev_id)
+{
+ struct stmpe_adc *info = (struct stmpe_adc *)dev_id;
+ u8 data[2];
+
+ if (info->channel > STMPE_TEMP_CHANNEL)
+ return IRQ_NONE;
+
+ if (info->channel <= STMPE_ADC_LAST_NR) {
+ int int_sta;
+
+ int_sta = stmpe_reg_read(info->stmpe, STMPE_REG_ADC_INT_STA);
+
+ /* Is the interrupt relevant */
+ if (!(int_sta & STMPE_ADC_CH(info->channel)))
+ return IRQ_NONE;
+
+ /* Read value */
+ stmpe_block_read(info->stmpe,
+ STMPE_REG_ADC_DATA_CH(info->channel), 2, data);
+
+ stmpe_reg_write(info->stmpe, STMPE_REG_ADC_INT_STA, int_sta);
+ } else if (info->channel == STMPE_TEMP_CHANNEL) {
+ /* Read value */
+ stmpe_block_read(info->stmpe, STMPE_REG_TEMP_DATA, 2, data);
+ }
+
+ info->value = ((u32)data[0] << 8) + data[1];
+ complete(&info->completion);
+
+ return IRQ_HANDLED;
+}
+
+static const struct iio_info stmpe_adc_iio_info = {
+ .read_raw = &stmpe_read_raw,
+};
+
+static void stmpe_adc_voltage_chan(struct iio_chan_spec *ics, int chan)
+{
+ ics->type = IIO_VOLTAGE;
+ ics->info_mask_separate = BIT(IIO_CHAN_INFO_RAW);
+ ics->info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE);
+ ics->indexed = 1;
+ ics->channel = chan;
+}
+
+static void stmpe_adc_temp_chan(struct iio_chan_spec *ics, int chan)
+{
+ ics->type = IIO_TEMP;
+ ics->info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED);
+ ics->indexed = 1;
+ ics->channel = chan;
+}
+
+static int stmpe_adc_init_hw(struct stmpe_adc *adc)
+{
+ struct stmpe *stmpe = adc->stmpe;
+
+ /* use temp irq for each conversion completion */
+ stmpe_reg_write(stmpe, STMPE_REG_TEMP_TH, 0);
+ stmpe_reg_write(stmpe, STMPE_REG_TEMP_TH + 1, 0);
+
+ return 0;
+}
+
+static int stmpe_adc_probe(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev = NULL;
+ struct stmpe_adc *info = NULL;
+ struct device_node *np;
+ u32 norequest_mask = 0;
+ int irq_temp, irq_adc;
+ int num_chan = 0;
+ int i = 0;
+ int ret;
+
+ irq_adc = platform_get_irq_byname(pdev, "STMPE_ADC");
+ if (irq_adc < 0)
+ return irq_adc;
+
+ indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(struct stmpe_adc));
+ if (!indio_dev) {
+ dev_err(&pdev->dev, "failed allocating iio device\n");
+ return -ENOMEM;
+ }
+
+ info = iio_priv(indio_dev);
+
+ init_completion(&info->completion);
+ ret = devm_request_threaded_irq(&pdev->dev, irq_adc, NULL,
+ stmpe_adc_isr, IRQF_ONESHOT,
+ "stmpe-adc", info);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed requesting irq, irq = %d\n",
+ irq_adc);
+ return ret;
+ }
+
+ irq_temp = platform_get_irq_byname(pdev, "STMPE_TEMP_SENS");
+ if (irq_temp >= 0) {
+ ret = devm_request_threaded_irq(&pdev->dev, irq_temp, NULL,
+ stmpe_adc_isr, IRQF_ONESHOT,
+ "stmpe-adc", info);
+ if (ret < 0)
+ dev_warn(&pdev->dev, "failed requesting irq for"
+ " temp sensor, irq = %d\n", irq_temp);
+ }
+
+ platform_set_drvdata(pdev, indio_dev);
+
+ indio_dev->name = dev_name(&pdev->dev);
+ indio_dev->dev.parent = &pdev->dev;
+ indio_dev->info = &stmpe_adc_iio_info;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+
+ info->stmpe = dev_get_drvdata(pdev->dev.parent);
+
+ np = pdev->dev.of_node;
+
+ if (!np)
+ dev_err(&pdev->dev, "no device tree node found\n");
+
+ of_property_read_u32(np, "st,norequest-mask", &norequest_mask);
+
+ for_each_clear_bit(i, (unsigned long *) &norequest_mask,
+ (STMPE_ADC_LAST_NR + 1)) {
+ stmpe_adc_voltage_chan(&info->stmpe_adc_iio_channels[num_chan], i);
+ num_chan++;
+ }
+ stmpe_adc_temp_chan(&info->stmpe_adc_iio_channels[num_chan], i);
+ num_chan++;
+ indio_dev->channels = info->stmpe_adc_iio_channels;
+ indio_dev->num_channels = num_chan;
+
+ ret = stmpe_adc_init_hw(info);
+ if (ret)
+ return ret;
+
+ return iio_device_register(indio_dev);
+}
+
+static int stmpe_adc_remove(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+ struct stmpe_adc *info = iio_priv(indio_dev);
+
+ iio_device_unregister(indio_dev);
+ stmpe_disable(info->stmpe, STMPE_BLOCK_ADC);
+
+ return 0;
+}
+
+static int __maybe_unused stmpe_adc_resume(struct device *dev)
+{
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct stmpe_adc *info = iio_priv(indio_dev);
+
+ stmpe_adc_init_hw(info);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(stmpe_adc_pm_ops, NULL, stmpe_adc_resume);
+
+static struct platform_driver stmpe_adc_driver = {
+ .probe = stmpe_adc_probe,
+ .remove = stmpe_adc_remove,
+ .driver = {
+ .name = "stmpe-adc",
+ .pm = &stmpe_adc_pm_ops,
+ },
+};
+
+module_platform_driver(stmpe_adc_driver);
+
+MODULE_AUTHOR("Stefan Agner <stefan.agner@toradex.com>");
+MODULE_DESCRIPTION("STMPEXXX ADC driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:stmpe-adc");
diff --git a/drivers/input/touchscreen/stmpe-ts.c b/drivers/input/touchscreen/stmpe-ts.c
index c5d9006588a2..81aa313d6e5a 100644
--- a/drivers/input/touchscreen/stmpe-ts.c
+++ b/drivers/input/touchscreen/stmpe-ts.c
@@ -30,8 +30,6 @@
* with touchscreen controller
*/
#define STMPE_REG_INT_STA 0x0B
-#define STMPE_REG_ADC_CTRL1 0x20
-#define STMPE_REG_ADC_CTRL2 0x21
#define STMPE_REG_TSC_CTRL 0x40
#define STMPE_REG_TSC_CFG 0x41
#define STMPE_REG_FIFO_TH 0x4A
@@ -58,15 +56,6 @@
* @idev: registered input device
* @work: a work item used to scan the device
* @dev: a pointer back to the MFD cell struct device*
- * @sample_time: ADC converstion time in number of clock.
- * (0 -> 36 clocks, 1 -> 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks,
- * 4 -> 80 clocks, 5 -> 96 clocks, 6 -> 144 clocks),
- * recommended is 4.
- * @mod_12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
- * @ref_sel: ADC reference source
- * (0 -> internal reference, 1 -> external reference)
- * @adc_freq: ADC Clock speed
- * (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz)
* @ave_ctrl: Sample average control
* (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 samples, 3 -> 8 samples)
* @touch_det_delay: Touch detect interrupt delay
@@ -88,10 +77,6 @@ struct stmpe_touch {
struct input_dev *idev;
struct delayed_work work;
struct device *dev;
- u8 sample_time;
- u8 mod_12b;
- u8 ref_sel;
- u8 adc_freq;
u8 ave_ctrl;
u8 touch_det_delay;
u8 settling;
@@ -176,7 +161,7 @@ static irqreturn_t stmpe_ts_handler(int irq, void *data)
input_report_key(ts->idev, BTN_TOUCH, 1);
input_sync(ts->idev);

- /* flush the FIFO after we have read out our values. */
+ /* flush the FIFO after we have read out our values. */
__stmpe_reset_fifo(ts->stmpe);

/* reenable the tsc */
@@ -202,20 +187,21 @@ static int stmpe_init_hw(struct stmpe_touch *ts)
return ret;
}

- adc_ctrl1 = STMPE_SAMPLE_TIME(ts->sample_time) |
- STMPE_MOD_12B(ts->mod_12b) | STMPE_REF_SEL(ts->ref_sel);
+ adc_ctrl1 = STMPE_SAMPLE_TIME(stmpe->sample_time) |
+ STMPE_MOD_12B(stmpe->mod_12b) |
+ STMPE_REF_SEL(stmpe->ref_sel);
adc_ctrl1_mask = STMPE_SAMPLE_TIME(0xff) | STMPE_MOD_12B(0xff) |
STMPE_REF_SEL(0xff);

- ret = stmpe_set_bits(stmpe, STMPE_REG_ADC_CTRL1,
+ ret = stmpe_set_bits(stmpe, STMPE811_REG_ADC_CTRL1,
adc_ctrl1_mask, adc_ctrl1);
if (ret) {
dev_err(dev, "Could not setup ADC\n");
return ret;
}

- ret = stmpe_set_bits(stmpe, STMPE_REG_ADC_CTRL2,
- STMPE_ADC_FREQ(0xff), STMPE_ADC_FREQ(ts->adc_freq));
+ ret = stmpe_set_bits(stmpe, STMPE811_REG_ADC_CTRL2,
+ STMPE_ADC_FREQ(0xff), STMPE_ADC_FREQ(stmpe->adc_freq));
if (ret) {
dev_err(dev, "Could not setup ADC\n");
return ret;
@@ -295,13 +281,13 @@ static void stmpe_ts_get_platform_info(struct platform_device *pdev,

if (np) {
if (!of_property_read_u32(np, "st,sample-time", &val))
- ts->sample_time = val;
+ ts->stmpe->sample_time = val;
if (!of_property_read_u32(np, "st,mod-12b", &val))
- ts->mod_12b = val;
+ ts->stmpe->mod_12b = val;
if (!of_property_read_u32(np, "st,ref-sel", &val))
- ts->ref_sel = val;
+ ts->stmpe->ref_sel = val;
if (!of_property_read_u32(np, "st,adc-freq", &val))
- ts->adc_freq = val;
+ ts->stmpe->adc_freq = val;
if (!of_property_read_u32(np, "st,ave-ctrl", &val))
ts->ave_ctrl = val;
if (!of_property_read_u32(np, "st,touch-det-delay", &val))
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 8c5dfdce4326..bba159e8eaa4 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1204,7 +1204,7 @@ config MFD_STMPE

Currently supported devices are:

- STMPE811: GPIO, Touchscreen
+ STMPE811: GPIO, Touchscreen, ADC
STMPE1601: GPIO, Keypad
STMPE1801: GPIO, Keypad
STMPE2401: GPIO, Keypad
@@ -1217,6 +1217,7 @@ config MFD_STMPE
GPIO: stmpe-gpio
Keypad: stmpe-keypad
Touchscreen: stmpe-ts
+ ADC: stmpe-adc

menu "STMicroelectronics STMPE Interface Drivers"
depends on MFD_STMPE
diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
index 566caca4efd8..35390d1c2e64 100644
--- a/drivers/mfd/stmpe.c
+++ b/drivers/mfd/stmpe.c
@@ -463,6 +463,28 @@ static const struct mfd_cell stmpe_ts_cell = {
.num_resources = ARRAY_SIZE(stmpe_ts_resources),
};

+/*
+ * ADC (STMPE811)
+ */
+
+static struct resource stmpe_adc_resources[] = {
+ {
+ .name = "STMPE_TEMP_SENS",
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .name = "STMPE_ADC",
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static const struct mfd_cell stmpe_adc_cell = {
+ .name = "stmpe-adc",
+ .of_compatible = "st,stmpe-adc",
+ .resources = stmpe_adc_resources,
+ .num_resources = ARRAY_SIZE(stmpe_adc_resources),
+};
+
/*
* STMPE811 or STMPE610
*/
@@ -497,6 +519,11 @@ static struct stmpe_variant_block stmpe811_blocks[] = {
.irq = STMPE811_IRQ_TOUCH_DET,
.block = STMPE_BLOCK_TOUCHSCREEN,
},
+ {
+ .cell = &stmpe_adc_cell,
+ .irq = STMPE811_IRQ_TEMP_SENS,
+ .block = STMPE_BLOCK_ADC,
+ },
};

static int stmpe811_enable(struct stmpe *stmpe, unsigned int blocks,
@@ -517,6 +544,44 @@ static int stmpe811_enable(struct stmpe *stmpe, unsigned int blocks,
enable ? 0 : mask);
}

+static int stmpe811_init_adc(struct stmpe *stmpe)
+{
+ int ret;
+ u8 adc_ctrl1, adc_ctrl1_mask;
+
+ ret = stmpe_enable(stmpe, STMPE_BLOCK_ADC);
+ if (ret) {
+ dev_err(stmpe->dev, "Could not enable clock for ADC\n");
+ goto err_adc;
+ }
+
+ adc_ctrl1 = STMPE_SAMPLE_TIME(stmpe->sample_time) |
+ STMPE_MOD_12B(stmpe->mod_12b) |
+ STMPE_REF_SEL(stmpe->ref_sel);
+ adc_ctrl1_mask = STMPE_SAMPLE_TIME(0xff) | STMPE_MOD_12B(0xff) |
+ STMPE_REF_SEL(0xff);
+
+ ret = stmpe_set_bits(stmpe, STMPE811_REG_ADC_CTRL1,
+ adc_ctrl1_mask, adc_ctrl1);
+ if (ret) {
+ dev_err(stmpe->dev, "Could not setup ADC\n");
+ goto err_adc;
+ }
+
+ ret = stmpe_set_bits(stmpe, STMPE811_REG_ADC_CTRL2,
+ STMPE_ADC_FREQ(0xff), STMPE_ADC_FREQ(stmpe->adc_freq));
+ if (ret) {
+ dev_err(stmpe->dev, "Could not setup ADC\n");
+ goto err_adc;
+ }
+
+ return 0;
+err_adc:
+ stmpe_disable(stmpe, STMPE_BLOCK_ADC);
+
+ return ret;
+}
+
static int stmpe811_get_altfunc(struct stmpe *stmpe, enum stmpe_block block)
{
/* 0 for touchscreen, 1 for GPIO */
@@ -1235,6 +1300,12 @@ static int stmpe_chip_init(struct stmpe *stmpe)
return ret;
}

+ if (id == STMPE811_ID) {
+ ret = stmpe811_init_adc(stmpe);
+ if (ret)
+ return ret;
+ }
+
return stmpe_reg_write(stmpe, stmpe->regs[STMPE_IDX_ICR_LSB], icr);
}

@@ -1325,6 +1396,7 @@ int stmpe_probe(struct stmpe_client_info *ci, enum stmpe_partnum partnum)
struct device_node *np = ci->dev->of_node;
struct stmpe *stmpe;
int ret;
+ u32 val;

pdata = devm_kzalloc(ci->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
@@ -1342,6 +1414,15 @@ int stmpe_probe(struct stmpe_client_info *ci, enum stmpe_partnum partnum)
mutex_init(&stmpe->irq_lock);
mutex_init(&stmpe->lock);

+ if (!of_property_read_u32(np, "st,sample-time", &val))
+ stmpe->sample_time = val;
+ if (!of_property_read_u32(np, "st,mod-12b", &val))
+ stmpe->mod_12b = val;
+ if (!of_property_read_u32(np, "st,ref-sel", &val))
+ stmpe->ref_sel = val;
+ if (!of_property_read_u32(np, "st,adc-freq", &val))
+ stmpe->adc_freq = val;
+
stmpe->dev = ci->dev;
stmpe->client = ci->client;
stmpe->pdata = pdata;
diff --git a/include/linux/mfd/stmpe.h b/include/linux/mfd/stmpe.h
index c0353f6431f9..86dca9e9880a 100644
--- a/include/linux/mfd/stmpe.h
+++ b/include/linux/mfd/stmpe.h
@@ -21,6 +21,9 @@
#define STMPE_I_DRIVE(x) (x & 0x1)
#define STMPE_OP_MODE(x) ((x & 0x7) << 1)

+#define STMPE811_REG_ADC_CTRL1 0x20
+#define STMPE811_REG_ADC_CTRL2 0x21
+
struct device;
struct regulator;

@@ -134,6 +137,12 @@ struct stmpe {
u8 ier[2];
u8 oldier[2];
struct stmpe_platform_data *pdata;
+
+ /* For devices that use an ADC */
+ u8 sample_time;
+ u8 mod_12b;
+ u8 ref_sel;
+ u8 adc_freq;
};

extern int stmpe_reg_write(struct stmpe *stmpe, u8 reg, u8 data);
--
2.19.1