From: Michael Straube <straube.linux@gmail.com>
To: gregkh@linuxfoundation.org
Cc: Larry.Finger@lwfinger.net, devel@driverdev.osuosl.org,
linux-kernel@vger.kernel.org,
Michael Straube <straube.linux@gmail.com>
Subject: [PATCH] staging: rtl8188eu: remove unused defines from wifi.h
Date: Mon, 18 Mar 2019 11:23:59 +0100 [thread overview]
Message-ID: <20190318102359.21859-1-straube.linux@gmail.com> (raw)
All defined P2P* in wifi.h are unused in the driver code,
so remove them.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
---
drivers/staging/rtl8188eu/include/wifi.h | 110 -----------------------
1 file changed, 110 deletions(-)
diff --git a/drivers/staging/rtl8188eu/include/wifi.h b/drivers/staging/rtl8188eu/include/wifi.h
index 5e91b9428c16..5f6b04b5016c 100644
--- a/drivers/staging/rtl8188eu/include/wifi.h
+++ b/drivers/staging/rtl8188eu/include/wifi.h
@@ -667,116 +667,6 @@ enum ht_cap_ampdu_factor {
#define WPS_ASSOC_STATE_ASSOCIATION_FAILURE 0x03
#define WPS_ASSOC_STATE_IP_FAILURE 0x04
-/* =====================P2P Section===================== */
-/* For P2P */
-#define P2POUI 0x506F9A09
-
-/* P2P Attribute ID */
-#define P2P_ATTR_STATUS 0x00
-#define P2P_ATTR_MINOR_REASON_CODE 0x01
-#define P2P_ATTR_CAPABILITY 0x02
-#define P2P_ATTR_DEVICE_ID 0x03
-#define P2P_ATTR_GO_INTENT 0x04
-#define P2P_ATTR_CONF_TIMEOUT 0x05
-#define P2P_ATTR_LISTEN_CH 0x06
-#define P2P_ATTR_GROUP_BSSID 0x07
-#define P2P_ATTR_EX_LISTEN_TIMING 0x08
-#define P2P_ATTR_INTENTED_IF_ADDR 0x09
-#define P2P_ATTR_MANAGEABILITY 0x0A
-#define P2P_ATTR_CH_LIST 0x0B
-#define P2P_ATTR_NOA 0x0C
-#define P2P_ATTR_DEVICE_INFO 0x0D
-#define P2P_ATTR_GROUP_INFO 0x0E
-#define P2P_ATTR_GROUP_ID 0x0F
-#define P2P_ATTR_INTERFACE 0x10
-#define P2P_ATTR_OPERATING_CH 0x11
-#define P2P_ATTR_INVITATION_FLAGS 0x12
-
-/* Value of Status Attribute */
-#define P2P_STATUS_SUCCESS 0x00
-#define P2P_STATUS_FAIL_INFO_UNAVAILABLE 0x01
-#define P2P_STATUS_FAIL_INCOMPATIBLE_PARAM 0x02
-#define P2P_STATUS_FAIL_LIMIT_REACHED 0x03
-#define P2P_STATUS_FAIL_INVALID_PARAM 0x04
-#define P2P_STATUS_FAIL_REQUEST_UNABLE 0x05
-#define P2P_STATUS_FAIL_PREVOUS_PROTO_ERR 0x06
-#define P2P_STATUS_FAIL_NO_COMMON_CH 0x07
-#define P2P_STATUS_FAIL_UNKNOWN_P2PGROUP 0x08
-#define P2P_STATUS_FAIL_BOTH_GOINTENT_15 0x09
-#define P2P_STATUS_FAIL_INCOMPATIBLE_PROVSION 0x0A
-#define P2P_STATUS_FAIL_USER_REJECT 0x0B
-
-/* Value of Invitation Flags Attribute */
-
-/* Value of Device Capability Bitmap */
-#define P2P_DEVCAP_SERVICE_DISCOVERY BIT(0)
-#define P2P_DEVCAP_CLIENT_DISCOVERABILITY BIT(1)
-#define P2P_DEVCAP_CONCURRENT_OPERATION BIT(2)
-#define P2P_DEVCAP_INFRA_MANAGED BIT(3)
-#define P2P_DEVCAP_DEVICE_LIMIT BIT(4)
-#define P2P_DEVCAP_INVITATION_PROC BIT(5)
-
-/* Value of Group Capability Bitmap */
-#define P2P_GRPCAP_GO BIT(0)
-#define P2P_GRPCAP_PERSISTENT_GROUP BIT(1)
-#define P2P_GRPCAP_GROUP_LIMIT BIT(2)
-#define P2P_GRPCAP_INTRABSS BIT(3)
-#define P2P_GRPCAP_CROSS_CONN BIT(4)
-#define P2P_GRPCAP_PERSISTENT_RECONN BIT(5)
-#define P2P_GRPCAP_GROUP_FORMATION BIT(6)
-
-/* P2P Public Action Frame (Management Frame) */
-#define P2P_PUB_ACTION_ACTION 0x09
-
-/* P2P Public Action Frame Type */
-#define P2P_GO_NEGO_REQ 0
-#define P2P_GO_NEGO_RESP 1
-#define P2P_GO_NEGO_CONF 2
-#define P2P_INVIT_REQ 3
-#define P2P_INVIT_RESP 4
-#define P2P_DEVDISC_REQ 5
-#define P2P_DEVDISC_RESP 6
-#define P2P_PROVISION_DISC_REQ 7
-#define P2P_PROVISION_DISC_RESP 8
-
-/* P2P Action Frame Type */
-#define P2P_NOTICE_OF_ABSENCE 0
-#define P2P_PRESENCE_REQUEST 1
-#define P2P_PRESENCE_RESPONSE 2
-#define P2P_GO_DISC_REQUEST 3
-
-#define P2P_PROVISIONING_SCAN_CNT 3
-
-/* default value, used when: (1)p2p disabled or (2)p2p enabled
- * but only do 1 scan phase
- */
-#define P2P_FINDPHASE_EX_NONE 0
-/* used when p2p enabled and want to do 1 scan phase and
- * P2P_FINDPHASE_EX_MAX-1 find phase
- */
-#define P2P_FINDPHASE_EX_FULL 1
-#define P2P_FINDPHASE_EX_SOCIAL_FIRST (P2P_FINDPHASE_EX_FULL+1)
-#define P2P_FINDPHASE_EX_MAX 4
-#define P2P_FINDPHASE_EX_SOCIAL_LAST P2P_FINDPHASE_EX_MAX
-
-/* 5 seconds timeout for sending the provision discovery request */
-#define P2P_PROVISION_TIMEOUT 5000
-/* 3 seconds timeout for sending the prov disc request concurrent mode */
-#define P2P_CONCURRENT_PROVISION_TIME 3000
-/* 5 seconds timeout for receiving the group negotiation response */
-#define P2P_GO_NEGO_TIMEOUT 5000
-/* 3 seconds timeout for sending the negotiation request under concurrent mode */
-#define P2P_CONCURRENT_GO_NEGO_TIME 3000
-/* 100ms */
-#define P2P_TX_PRESCAN_TIMEOUT 100
-/* 5 seconds timeout for sending the invitation request */
-#define P2P_INVITE_TIMEOUT 5000
-/* 3 seconds timeout for sending the invitation request under concurrent mode */
-#define P2P_CONCURRENT_INVITE_TIME 3000
-/* 25 seconds timeout to reset the scan channel (based on channel plan) */
-#define P2P_RESET_SCAN_CH 25000
-#define P2P_MAX_INTENT 15
-
/* WPS Configuration Method */
#define WPS_CM_NONE 0x0000
#define WPS_CM_LABEL 0x0004
--
2.21.0
reply other threads:[~2019-03-18 10:24 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190318102359.21859-1-straube.linux@gmail.com \
--to=straube.linux@gmail.com \
--cc=Larry.Finger@lwfinger.net \
--cc=devel@driverdev.osuosl.org \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox